Xerox ColorQube 8700 User's Manual
Contents
1. 8 Elatec TWNS 8 Magnetic Stripe Reader 8 ID TECH Magnetic Stripe Reader Configuration Upgrade 9 RF IDeas Magnetic Stripe Reader Configuration Upgrade 10 Document Version History Error Bookmark not defined USB Card Reader Configuration Guide i Overview This document describes how to configure off box authentication to a Solution Partner Authentication server with a USB card reader using the new open USB standard The USB card reader is connected directly to the USB port on the Xerox machine When the USB card reader is connected to the machine an external card reading controller is no longer required This feature is used to control access to the MFP via employee badge to a partner authentication server Once the server is setup to communicate with the device and selected Services are locked at the LUI access to those locked services will only be granted to walk up users with valid cards and or System Administrators Supported Reader Technology Employee badges can contain one or multiple technologies for storing user identity information The 4 prominent methods in use today are Wireless which is also known as Proximity Magnetic Stripe Visual Barcode and Smart Cards This document addresses support for Proximity Magnetic Stripe2. and Visual Barcode readers There are two classes of proximity readers those which can read the Card Serial Number CSN and those which can read from secure memory segments contained on specific card types This solution will only support proximity readers which send the CSN Smart Card Authentication CAC PIV NET etc are addressed in the Smart Card feature documentation Operation This feature is designed to read data from an employee badge and to package that data into a message which is sent to the server running software from solution provider This requires that the solution provider has developed their software to be compatible with this feature using the Convenience Authentication API This feature enables solution providers to provide authentication pull printing and accounting which is tied the user associated with the employee s badge This feature is configured using most of the Xerox Secure Access set up screens but is not compatible with the Xerox Secure Access feature itself It is not compatible with the white card readers supplied as part of Xerox Secure Access Each of the currently approved badge readers has internal intelligence to read a card and to acknowledge success by blinking the LED or creating sound with the beeper on the reader itself Note that this behavior is different than with the Xerox Secure Access XSA solution With XSA the authentication server is in control of the LED on the reader This means
3. users will observe faster acknowledgement that their card has been recognized because that recognition does not require communication with a server A side effect is that the LED indications will not be consistent with those of the XSA solution The card readers will have power applied when the MFP is awake and while it is in Sleep mode A card swipe will take the MFP out of Sleep mode and will initiate an authentication sequence To meet EPA USB Card Reader Configuration Guide 2 Energy Star requirements power is removed from the reader when the MFP enters Deep Sleep In Deep Sleep the card reader will appear to be dead Since the reader has no power the LED will not be illuminated A card swipe in Deep Sleep mode will be ignored Users must first awaken the MFP using the Energy Saver button Once the MFP is awake the card reader will again be functional Diagnostics USB card readers have been chosen which communicate using the Human Interface Device HID keyboard emulation mode The rationale for this decision is primarily to aid in the ability to troubleshoot problems in the field An HID reader can be plugged directly into any personal computer and tested independent from the MFP All one need do is open a document application such as Microsoft Notepad which expects Text as input If an employee badge is swiped across the reader the CSN will be displayed in the Notepad application This makes it easy to diagnose reader related problems in t
4. 493801 In order to determine if the reader conforms to the Xerox standard the reader can be easily tested using a personal computer 1 Open a text document tool like Microsoft Notepad 2 Connect the magnetic stripe reader to a USB port on the computer 3 Wait for the card reader driver to be installed 4 Swipe one of the customer s mag stripe cards 5 Observe the data displayed in Notepad If the data is presented in a single line with one carriage return the reader is compatible and no programming is required b If the reader sends multiple lines or strips off the line start and end characters the reader will need to be reprogrammed Each of the card readers listed in Appendix Acan be reprogrammed to this format using tools supplied by each manufacturer Below are URLsto the manufacturer s websites where the card reader configuration tool can be retrieved Note that the YSoft and ID TECH Magnetic stripe readers listed in Appendix A already conformed to the Xerox standard and did not need to be upgraded 8 USB Card Reader Configuration Guide RF IDeas pcSwipeConfig exe htip www rfideas com Software ID TECH USB Swipe amp Insert Reader programming tool http www idtechproducts com index php o0ption com_ docman amp task cat_view amp gid 298 amp ltemid 79 MagTek MiniMag II Configuration Software http www magtek com support software demo programs usb swipe insert asp ID TECH Magnetic Stripe Reader Configurati
5. USB card reader a Depending on the particular reader you should observe the card reader LED change color or the reader will beep b Observe that the user is authenticated and their username appears in the upper right corner of the local user interface display 6 Swipe or scan the same card with the card reader a Depending on the particular reader you should observe the card reader LED change color or the reader will beep b Observe that the user is logged out and that the Default Walkup Screen is displayed If the Default Screen is locked the blocking screen will be displayed 6 USB Card Reader Configuration Guide Appendix A Supported USB card readers Proximity readers These support 125Khz amp 13 56Mhz which include HID Prox Mifare HID iCLASS LEGIC and a variety of other card types Elatec TWN3 amp TWN4 family USB readers htip www elatec rfid com RF IDeas RDR XX6081 AKU family USB Prox readers and all other readers from the USB Enroll family including pcProx Plus http www rfideas com YSoft V2 family USB readers http www ysoft com Magnetic Stripe readers These support ISO 7813 and ISO 4909 encoding standards for tracks 1 2 amp 3 RF IDeas MS3 00M1AKU MagStripe reader http www rfideas com ID TECH MiniMag II MagStripe reader htto www idtechproducts com MagTek Magnetic stripe reader htto www magtek com YSoft V2 Magnetic stripe reader http www ysoft com Vi
6. Xerox USB Card Reader Configuration Guide Xerox WorkCentre 51 Xerox WorkCentre 56xx Xerox WorkCentre 57xx Xerox WorkCentre 6400 Xerox WorkCentre 75xx Xerox WorkCentre 77xx Xerox ColorQube 87xx 89xx Xerox ColorQube 92xx Xerox ColorQube 93xx February 2014 2014 Xerox Corporation All rights reserved Xerox and Xerox and Design WorkCentre ColorQube and Xerox Extensible Interface Platform are trademarks of the Xerox Corporation in the United States and or other countries Other company trademarks are also acknowledged Document Version 3 0 February 2014 dc13cd023 Table of Contents Ras MN E 2 Supported Reader 2 eiu M 2 CD UO EC 3 Card Reader Software rrr nre tertie pk eger nner 3 Magnetic Stripe Reader Constraints 3 44 11 11 5 eed ET 4 Installation m Ennn Ennet 4 Connecting the USB card 4 Configuring the machine to use USB card reader for authentication 5 Create a Device Certificate and Enable 581 5 Appendix A Supported USB 7 Appendix B Card Reader Configuration Setting
7. elds will be available for selection Choose whether the server will enter the appropriate accounting code or whether the user will be prompted to enter a code 10 Fill in the Device Instructional Blocking Window details the Window Title and Instructional Text For example Please swipe your card to log on 11 Select Save If the USB Card Reader Detection Policy was set to Prevent use of device when USB card reader is disconnected then when the summary screen appears it will indicate whether an Approved card reader is Connected Not Connected or Not Supported Verify Connected Reader At this point the local UI should show a pop up or message indicating that the card reader is not connected 1 Insert a qualified card reader into the USB port and observe that the message goes away 2 Remove the card reader and observe that the pop up reappears 3 Plug the card reader back in Validation At this point the system is fully configured for authentication Lock a few services to verify that authentication is required for access Via CWIS navigate to Properties Security Authentication Tools amp Feature Access Under Presets select Custom Access Select Locked for any Services Features or Pathways that should be secured Select Apply TS At the local Ul navigate to a locked Service or Pathway Verify the prompt to swipe a card to log on is displayed 5 Swipe or scan a valid card with the
8. ge 1 Navigate to Security Authentication Setup 2 Select Xerox Secure Access Unified ID System as the Authentication method on the machine s touch user interface 3 Under Configuration Setting select the Edit button next to Xerox Secure Access Setup 4 Normally the configuration settings are pushed down from the partner server If you plan to use this method select Close and consult the particular solution partner s installation and configuration documentation If you wish to configure these settings manually select Manually Configure 5 Fillin the server Communication details using either IP address or Host Name Include the path to the server 6 Verify that the Embedded box is NOT checked This checkbox enables software which only works with the white egg shaped Xerox Secure Access card readers 7 Setthe USB Card Reader Detection Policy to either allow or deny access to the MFP if the card reader becomes unplugged This will cause a Caution screen to appear whenever the card reader is accidentally unplugged and remind the user to plug it back in 8 Setthe Device Log In Method to either enable only swipe card authentication or whether to also offer Alternate Authentication where the user manually enters their logon credentials in the event they lost or forgot their card USB Card Reader Configuration Guide 5 9 Configure Accounting Information If the Job Based Accounting option has been purchased these fi
9. he field Since this is a relatively new feature we have chosen to start cautiously As a result the only readers which will be recognized are those which have been tested and found acceptable by engineering If any reader is connected which is not listed in Appendix A the MFP will totally ignore it The Configuration section of this document will address how the MFP will indicate that a non supported reader is connected Card Reader Software Magnetic Stripe Reader Constraints There is a wide variety in the factory default behavior of magnetic stripe readers While all of the tested readers are capable of supporting the applicable ISO standards they do not initially send the card data in exactly the same way Each of the supported readers can be programmed in the way they send card data and each of the manufacturers provides PC based tools to program the reader As aresult a standard configuration can be defined across all readers In our defined standard configuration the reader will emit every line of data which the magnetic stripe card contains The reader will emit all line sentinels field separators and line termination characters and will not mask out any data This will enable solution partners full access to card data which can be processed as they desire Appendix B contains directions to properly configure each magnetic stripe reader USB Card Reader Configuration Guide 3 Prerequisites The Multi function Printer software mus
10. netic Card Reader Download and install pcSwipeConfig exe 1 Connect the reader to the workstation and run the pcSwipe tool a Select the Scan Connect button so the tool will interrogate the reader 2 Once areader has been recognized select the Fields tab a Inthe Tracks field enable tracks 1 2 amp 3 b Select User Field 1 and insure that the checkbox next to Show Sentinels and Separators is selected C Select User Field 2 and then 3 and insure the Show Sentinels and Separators field is selected for those as well d Select User Field 4 Insure the checkbox next to Enable is selected f Verify that the word ENTER appears in the text field adjacent to the User Field 4 button This is the termination to the data stream g ENTER does not appear select the keyboard icon on the left labeled Keys h Within the pop up which will appear select ENTER and then Insert 3 Select the LED Beep tab a Verify that the LED and tone response match the customer s desired behavior When all configuration options have been set this can be written to the reader From the pcSwipeConfig toolbar select the Flash icon The reader will beep and blink and beep when the new settings have been written 10 USB Card Reader Configuration Guide
11. on Upgrade Software can be found at http www idtechproducts com download swipe readers doc download 38 configuration software html Select the IDTech Xerox Config zip file to access the ID TECH MagStripe Configuration file that will be required later in the setup process The file is located within the USB Card Reader Install zip file mentioned in the Prerequisites section Save the file to your PC for later use After installing note requires a restart and running the Magstripe Configuration Utility 1 Select Reader Interface button 2 Select USB Radio button below USB picture and then select Continue The reader will beep a few times and the screen will return back to the default view 3 Select Change Basic Reader Settings Select Load from File 5 Navigate to where you saved the configuration file then select it followed by Open You should get a message that loading the file was successful Select 6 Select Send to MSR Reader will beep once or twice and you see a message that the settings were successfully written 7 You are now done programming the reader Select Close and then EXIT USB Card Reader Configuration Guide 9 RF Magnetic Stripe Reader Configuration Upgrade RF Ideas magnetic stripe readers can be configured with the pcSwipe tool available from their website http www rfideas com Select Support Software amp Downloads then scroll down to pcSwipe Mag
12. r configuration to be compatible with the MFP This is defined in Appendix B Please be sure the software and configuration are correct before the reader is installed on the MFP 4 USB Card Reader Configuration Guide Configuring the machine to use USB card reader for authentication Create a Device Certificate and Enable SSL The following configuration settings can only be completed via CWIS Note Either the existing default certificate can be used or the user can install their own certificate The steps below use the default certificate 1 Open a web browser and connect to CWIS by entering the following URL http enter device IP address 2 Click on the Properties Certificates Security Certificates note SSL must be enabled If it is not follow the Configure SSL link on this page to enable SSL then repeat step 2 Enter System Administrator credentials if prompted On the Xerox Device Certificate tab click Create New Xerox Device Certificate Select Connection Enabled with port 80 Select Secure HTTPS Disabled Select Default Xerox Device Certificate Select Device Certificate Default Xerox Device Certificate 9 Complete all text fill in fields 10 Select the Subject Alternative Name checkbox 11 When all entries are complete select Finish 12 Wait while the new certificate is created 13 Select Apply Configure the feature the existing Xerox Secure Access web pa
13. sual Barcode Reader These support one dimensional visual barcodes Honeywell amp 38009 http www honeywellaidc com These support two dimensional visual barcodes Motorola 05457 amp 059208 http www motorola com USB Card Reader Configuration Guide 7 Appendix Card Reader Configuration Setting Elatec TWN3 Software Elatec TWNG readers must have at least software version V3 03d 4 39 to operate properly on the WorkCentre 53xx WorkCentre 7120 and WorkCentre 74xx If connecting an Elatec reader with earlier software to one of these products the reader software will need to be upgraded first Please contact Elatec Customer Support for this software update support 2elatec rfid com Magnetic Stripe Reader Configuration The ISO specification for magnetic stripe cards defines the data format for the 3 possible tracks on a mag stripe card Each line starts with a unique character called a sentinel which denotes which line of data is being read The ISO spec specifies characters used to define the data blocks within a line as well as the line termination character Shown below are three lines of data contained on a hypothetical 3 track mag stripe card B6006493801 XEROX 1012110 LQI 6006493801 101211050282809 6006493801 Xerox MFPs require this data to be concatenated into a single string with only one carriage return as the terminating character B6006493801 XEROX 1012110 LQI 6006493801 10121 1050282809 6006
14. t meet a minimum software level The supported devices and the minimum software levels are WC51xx software Version 21 120 65 170 WC56xx software SBC Version 25 54 65 170 MBC Version 21 120 65 170 WC57xx software Version 061 132 222 28900 WC6400 software Version 061 070 102 23501 WC75xx software Version 061 121 222 21500 WC77xx software Version 061 090 223 10600 CQ87xx 89xx software Version 071 160 222 28900 CQ93xx software Version 61 180 222 08700 e Must be using supported cards and card readers See Appendix A e The Secure Socket Layer SSL must be enabled Note e Extensible service setup has to be enabled if the Xerox Extensible Interface Platform EIP application is used The open USB card reader standard cannot be used with Xerox Secure Access branded readers Installation Connecting the USB card reader Connect the card reader to one of the available USB ports on the MFP The reader can be mounted in a number of locations on the MFP For example it can be placed on the top panel next to the UI on the left hand shelf or on the top of the finisher Most of the tested readers will indicate that they have power and are operational by illuminating an LED and possibly emitting a sound once the card reader has booted up Please insure the card reader software is at the latest level by checking with the particular manufacture web site as outlined in Appendix A Some readers require a particula
Download Pdf Manuals
Related Search