Home
WhisperKool Platinum 042610 User's Manual
Contents
1. PLATINUM MINI SPLIT WhisperKOOL UNIT SPECIFIC INSTALLATION GUIDE The Coolest Thing In Wine Storage TO BE USED WITH THE SPLIT SYSTEM OWNERS MANUAL Required Tools e Drill e Phillips Screwdriver Ladder e 5 32 Drill Bit e Tape Measure e Level e 1 4 Socket Drill Bit Brazing Torch e Pliers e 1 4 Wrench e Drywall Saw e Pencil PACKAGE CONTENTS Oe 1 Mini Split Evaporator Unit 10 Piece of Cork Tape 1 1 12 Foot Bottle Probe 1 Split System Owner s Manual 4 2 8 Hex Head Screws 1 Unit Specific Installation Guide 10 FT 3 8 Drain Line 1 Evaporator Mounting Template Sight Glass 1 Warranty Registration Card 4 Filter Drier WN oa owe as ay WH 1 1 1 EVAPORATOR PREPARATION 1 Remove the access panel 2 Install bottle probe connector 3 Install 3 8 drain line on drain pan 4 Depending on your desired installation remove the rear or bottom knockouts for the line set and drain line 5 Using a 5 32 drill bit on a drill from the outside of the unit Eos I E cut holes through the unit s insulation for the line e set and drain line e 1738 E Alpine Ave Stockton CA 95205 1 800 343 9463 www whisperkool com Page 1 INSTALLING THE EVAPORATOR Note The evaporator is designed to be mounted on two standard 16 spaced wall studs 1 Locate two desired wall studs Mark center lines for the studs vertically on the
2. pply wires into the unit through the power knockout and install the supplied strain relief 13 Connect power supply wires to the pre installed butt splice connectors located inside of the unit Hot Black Neutral White Ground Green 14 Route drain line out of the unit to desired location 15 Connect the Bottle Probe 16 Reinstall the access panel removed in step 1 of Evaporator Preparation 17 Plug in the evaporator and condensing unit 18 Follow standard refrigeration system charging processes WhisperKOOL recommends pressurizing the sys tem using dry nitrogen then allow unit to hold pressure for 30 minutes prior to charging 19 Once the system is charged adjust the Thermal Expansion Valve to maintain 8 12 F superheat if necessary Please refer to the Split System Owners Manual for condensing unit wiring diagrams and general split system information PMS 01 042610 Page 2
3. wall 16 inches apart followed by a level horizontal line at your desired height Note The top of the unit needs to be installed at a minimum of 6 inches from the ceiling and no further than 18 inches from the ceiling 2 Place the installation template on the wall lining up the vertical lines through the sight slots 3 Mark through the indicated Mounting Screw holes and location for the Access Hole 4 Set Installation Template aside 5 Install the supplied four 2 8 Hex Head Screws into the marked mounting screw locations leaving 1 6 be tween the wall surface and screw head 6 Cut out the Access Hole using a drywall saw or desired method Be sure to clear all debris and insulation 7 The wall is now ready for installation Place the prepared unit below the install location Note During installation WhisperKOOL recommends elevating the unit close to the install height 8 Raise the evaporator to the installation location Align the rear key holes with the mounting screws and mount the unit 9 Using a 1 4 wrench or socket tighten accessible mounting screws inside of the unit 10 Route the 3 8 suction line and 1 4 liquid line into the unit and braze Note Angle the flame up and away from any electrical O 3 8 Suction and insulation while brazing inside of the unit 1 4 Liquid 11 Insulate the 3 8 suction line with the 10 piece of e Drain supplied cork tape 12 Route power su
Download Pdf Manuals
Related Search
Related Contents
Swingline GBC CombBind C450E PRESOTERAPIA ORIENTAÇÕES GERAIS Sony ERS-7 User's Manual Model WBS4345 - whirlpool documents NucleoSpin® 96 Plant II (Core Kit) - MACHEREY Advances in gringo series 3 - Institut für Informatik Lenovo T60 User's Manual Das ÖAMTC - rastundruh.heim.at Copyright © All rights reserved.
Failed to retrieve file