Whirlpool W10531342A User's Manual
Contents
1. ace D 5 Using the Phillips screwdriver mount anti tip bracket to the E wall or floor with the two 12 x 1 screws provided F 6 Move range close enough to opening to allow for final gas and electrical connections Remove shipping base cardboard or hardboard from under range G 7 Move range into its final location making sure rear leveling leg slides into anti tip bracket A Pressure regulator D Union connection fitting E Nipple B 90 elbow F Manual shutoff valve C Black iron pipe G or 3 4 gas pipe Typical flexible connection 1 Apply pipe joint compound made for use with LP gas to the smaller thread ends of the flexible connector adapters see B 8 Move range forward onto shipping base cardboard or and F in the following illustration hardboard to continue installing the range using the following 2 installation instructions Attach one adapter to the gas pressure regulator and the other adapter to the gas shutoff valve Tighten both adapters 3 Use a combination wrench and pliers to attach the flexible connector to the adapters Check that connector is not kinked EA i A F li aff B C E H A Pressure regulator connection fitting B Use pipe joint compound C Adapter D Flexible connector E Adapter F Use pipe joint compound G Manual shutoff valve H or 34 gas pipe Complete Connection 1 Locate gas pre2. GAS CONVERSIONS AWARNING Explosion Hazard Use a new CSA International approved gas supply line Install a shut off valve Securely tighten all gas connections If connected to LP have a qualified person make sure gas pressure does not exceed 14 36 cm water column Examples of a qualified person include licensed heating personnel authorized gas company personnel and authorized service personnel Failure to do so can result in death explosion or fire Gas conversions from Natural gas to LP gas or from LP gas to Natural gas must be done by a qualified installer AWARNING Tip Over Hazard A child or adult can tip the range and be killed Install anti tip bracket to floor or wall per installation instructions Slide range back so rear range foot is engaged in the slot of the anti tip bracket Re engage anti tip bracket if range is moved Do not operate range without anti tip bracket installed and engaged Failure to follow these instructions can result in death or serious burns to children and adults To Convert Gas Pressure Regulator Turn manual shutoff valve to the closed position A Gas supply line B Manual shutoff valve closed position C To range Unplug range or disconnect power Open broiler door and remove broiler pan The gas pressure regulator is located in the back right hand corner of the broiler compartment A Gas press
3. Refer to the Complete Installation section to complete this procedure on AWARNING Tip Over Hazard A child or adult can tip the range and be killed Install anti tip bracket to floor or wall per installation instructions Slide range back so rear range foot is engaged in the slot of the anti tip bracket Re engage anti tip bracket if range is moved Do not operate range without anti tip bracket installed and engaged Failure to follow these instructions can result in death or serious burns to children and adults To Convert Gas Pressure Regulator Turn manual shutoff valve to the closed position A Gas supply line B Manual shutoff valve closed position C To range Unplug range or disconnect power Open broiler door and remove broiler pan The gas pressure regulator is located in the back right hand corner of the broiler compartment A Gas pressure regulator IMPORTANT Do not remove the gas pressure regulator 4 Remove the cap from the gas pressure regulator using a flat blade screwdriver NOTE Do not remove the spring beneath the cap A Cap 5 Turn the cap over so that N or NAT is visible A Cap 6 Reinstall the cap To Convert Surface Burners 1 Remove burner grate burner caps and burners A Burner cap B Burner 2 Locate the Natural gas orifice spuds for top burners in the package containing literat
4. A Anti tip bracket B 12 x 1 screws 2 Literature bag Conversion orifice spuds inside bag containing literature Anti tip bracket must be securely mounted to floor or wall Thickness of flooring may require longer screws to anchor bracket to floor Parts needed m 9V DC alkaline battery not included Check local codes and consult gas supplier Check existing gas supply and electrical supply See Electrical Requirements and Gas Supply Requirements sections t QUADREX is a registered trademark of NLW Holdings Inc 4 IMPORTANT Observe all governing codes and ordinances Do not obstruct flow of combustion and ventilation air m Itis the installer s responsibility to comply with installation clearances specified on the model serial rating plate The model serial rating plate is located on the oven frame behind the left side of the broiler door A Model serial rating plate location m The range should be located for convenient use in the kitchen m Recessed installations must provide complete enclosure of the sides and rear of the range m To eliminate the risk of burns or fire by reaching over heated surface units cabinet storage space located above the surface units should be avoided If cabinet storage is to be provided the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 12 7 cm beyond the bottom of the cabinets m All openings
5. LP Gas CONVErSION aarne enrenar ninian iiei A 14 Complete ConverSion cesseeceeseeneeeeeeeeeeeeeeeeeaeeenesneeeeeeeaes 16 Natural Gas Conversion ssssssseeeresesisirersrisirernsinsinsinsrnrrnrnnrnne 16 Complete ConverSion cssseecesereeneeeeeeseeeeeeeeesaeeeneeneeeeeeeaes 18 IMPORTANT Save for local inspector s use Installer Leave installation instructions with the homeowner Homeowner Keep installation instructions for future reference W10531342A RANGE SAFETY Your safety and the safety of others are very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and either the word DANGER or WARNING These words mean You can be killed or seriously injured if you don t immediately A DANG ER follow instructions You can be killed or seriously injured if you don t follow A WARN i N e instructions All safety messages will tell you what the potential hazard is tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed WARNING If the information in this manual is not followed exactly a fire or explosion may result causing property damage personal injury or death Do not store
6. battery facing the bottom and the blue wires facing up and close the plastic battery box IMPORTANT Do not operate bake burner without the metal battery top installed and secured 7 Replace the broiler pan and grill in the broiler rack 8 Close the broiler door Test the battery by lighting a burner See Electronic Ignition System section The electrode in each burner will spark and make a clicking noise When the battery needs to be replaced follow these instructions and remove the old battery before inserting a new battery Properly dispose of the old battery See the Battery Status Indicator section to know when to replace the battery m The battery status indicator on the control panel will show the recommended time to replace the battery O BATTERY STATUS Battery status indicator m If the battery status indicator lights up red when any of the burner knobs is in the LITE position then it is recommended you replace the battery with a new 9V DC alkaline battery NOTE If any knob is turned to the LITE position and there is no clicking noise or the battery status does not light either the battery power is very low or completely discharged or there is no battery connected to the battery case In this event replace the battery or install a new 9V DC alkaline battery IMPORTANT If the range will be unused for a long time it is recommended that the battery is removed and stored out of reach o
7. control knob to the LITE position The flame should light within 4 seconds 29 OFF w LO MED Turn control knob to the HI position after burner lights Check each cooktop burner for proper flame The small inner cone should have a very distinct blue flame 1 4 0 64 cm to Ya 0 13 cm long The outer cone is not as distinct as the inner cone A l A Outer cone B Inner cone Turn the control knob quickly to the LO position after the burner lights If the flame goes out turn the control knob to the OFF position Check each cooktop burner for proper low flame The low flame should be a minimum steady blue flame The flame size should be 1 4 to 3 0 64 cm to 0 95 cm high If the low flame needs adjusting 1 2 3 12 With the burner flame on turn control knob to the LO position and remove control knob Insert a small flat blade screwdriver into the valve stem Turn the valve adjusting screw to obtain the smallest flame that will not go out when the control of a cold burner is quickly turned from HI to LO Turn right to decrease flame height Turn left to increase flame height Repeat for other cooktop burners as needed A Valve stem Replace control knob Check Operation of Oven Broil Burner 1 Open the oven door 2 Press in and turn the oven control knob to the LITE position OFF 400 450 OVEN TEMP m The oven burner should ligh
8. or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU SMELL GAS e Do not try to light any appliance e Do not touch any electrical switch e Do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or the gas supplier WARNING Gas leaks cannot always be detected by smell Gas suppliers recommend that you use a gas detector approved by UL or CSA For more information contact your gas supplier If a gas leak is detected follow the What to do if you smell gas instructions IMPORTANT Do not install a ventilation system that blows air downward toward this gas cooking appliance This type of ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or unintended operation In the State of Massachusetts the following installation instructions apply m Installations and repairs must be performed by a qualified or licensed contractor plumber or gasfitter qualified or licensed by the State of Massachusetts m If using a ball valve it shall be a T handle type m A flexible gas connector when used must not exceed 3 feet Range Foot Anti Tip Bracket AWA
9. the anti tip bracket may not be installed correctly Do not operate the range without anti tip bracket installed and engaged Please reference the Assistance or Service section of the Use and Care Guide or the cover or Warranty section of the User Instructions to contact service Place a standard flat rack in oven Place level on the rack and check levelness of the range first side to side then front to back If range is not level pull range forward until rear leveling leg is removed from the anti tip bracket Use a drive ratchet and slip joint pliers to adjust leveling legs up or down until the range is level Push range back into position Check that rear leveling leg is engaged in the anti tip bracket NOTE Range must be level for satisfactory baking performance 10 A Battery holder location A Screw B Metal battery top C Plastic battery box D Battery holder NOTE Metal battery top is included in the bag containing literature To install or replace the 9V DC alkaline battery follow the steps below 1 Open the broiler door 2 Remove broiler pan and grill from broiler 3 Using a Phillips screwdriver remove the metal battery top from the bottom of the range and open the plastic battery box 4 Remove the battery holder and insert a new 9V DC alkaline battery into it 5 Replace the battery holder in the plastic battery box with the
10. INSTALLATION INSTRUCTIONS 20 50 8 CM FREESTANDING GAS RANGE with Standard Clean Oven Table of Contents RANGE SAFE Y ticicciicccsccsscccacicactdcteensceustczsdeecttiessecndveexectsivtitecevedsace 2 INSTALLATION REQUIREMENTS csscsssscsseeeeeeentententeneenees 4 TOOIS GNC PAIS vcseisscesecesccentsenecssvesceeuivostenareyandvevustivanchavriniesese secs 4 Location Requirements cceecceeeeeceeeeceeeeseaeeeeeeeeeneeseeeeseneees 4 Electrical REQUuIreMeNts cccccceeeeeeeeteeeeeeseeeeeeeeeeeeeeeeeneeenees 5 Gas Supply Requirement eeeesseeeeeeseeeeeeeeeeeseeeeeeeeneeenes 6 INSTALLATION INSTRUCTIONS ccctecstsssterseerscrsersenseneees 7 Unpack Ranges Aidan nihil Abadia dentin 7 Install Anti Tip Bracket ccccccesceeeseeeeeeeeeeeeseeeeeeeeeeeeeeeeeeesnees 7 Make Gas Connection cesceeeceeseeneeenreeeeeeeeeeeeaeeeaeeeeeeeeeeneeees 8 Verify Anti Tip Bracket Is Installed and Engaged 00 9 Level RANG ai ccstetesatiestecansdawnctncds livevedeasenavanenseeseestasieecsteeeeeteatyaely 10 Installing Replacing the Battery eeeeseeseeseereeeeseeeeeeeeenee 10 Battery Status INGICAtO ee eeeeeseeeeeeeeeeeeeeeeeeeeeeteeeteaeeeaeeaeee 11 Electronic Ignition SyStem ceceesseceeeeeeeeeeeteeeeaeeeeeeeeeeeeeeaes 11 Complete Installation ceeeceeseeseeeeeseeeeeeeeeeeeeeseeeeeeeneeeeeeeaes 13 GAS CONVERSIONS ccctecsteseeeseesnenseeneeeseeeseerseeeseessneneeeneeas 14
11. RNING Tip Over Hazard A child or adult can tip the range and be killed Install anti tip bracket to floor or wall per installation instructions Slide range back so rear range foot is engaged in the slot of the anti tip bracket Re engage anti tip bracket if range is moved Do not operate range without anti tip bracket installed and engaged Failure to follow these instructions can result in death or serious burns to children and adults To verify the anti tip bracket is installed and engaged e Slide range forward e Look for the anti tip bracket securely attached to floor or wall e Slide range back so rear range foot is under anti tip bracket e See installation instructions for details INSTALLATION REQUIREMENTS Gather the required tools and parts before starting installation Read and follow the instructions provided with any tools listed here Tools needed Tape measure Marker or pencil Flat blade screwdriver Pipe joint compound Phillips screwdriver resistant to LP gas m Noncorrosive leak detection solution For LP Natural Gas Conversions m 3 combination wrench Level Hand or electric drill Wrench or pliers Pipe wrench 1546 combination wrench Y2 combination wrench 14 drive ratchet combination wrench _ nut driver 7 mm e nut driver Ya 3 2 mm drill bit for wood floors Quadrex or Phillips screwdriver m Masking tape Parts supplied Check that all parts are included
12. e Installations ANSI A225 1 NFPA 501A or with local codes Mobile home installations require m When this range is installed in a mobile home it must be secured to the floor during transit Any method of securing the range is adequate as long as it conforms to the standards listed above Product Dimensions Freestanding Range J 4112 106 6 cm 25 65 9 cm 19 50 cm Cabinet Dimensions Cabinet opening dimensions shown are for 25 64 0 cm countertop depth 24 61 0 cm base cabinet depth and 36 91 4 cm countertop height If the cabinet depth is greater than 24 61 0 cm oven frame must extend beyond cabinet fronts by 1 3 cm minimum A 18 45 7 cm min clearance upper side cabinet to countertop B 13 33 0 cm max upper cabinet depth C 20 50 8 cm min cabinet opening width D For minimum clearance to top of cooktop see NOTE E 20 81 1 cm min opening width F This shaded area recommended for installation of gas pipe G 3 7 6 cm min countertop space to side wall or other combustible material H 10 25 4 cm 1 5 14 cm J 4 10 cm K 2 5 1 cm NOTE 24 61 0 cm minimum when bottom of wood or metal cabinet is covered by not less than 1 4 0 64 cm flame retardant millboard covered with not less than No 28 MSG sheet steel 0 015 0 4 mm stainless steel 0 024 0 6 mm aluminum or 0 020 0 5 mm copper 30 76 2 cm
13. eck that all parts are now installed If there is an extra part go back through the steps to see which step was skipped Check that you have all of your tools Dispose of recycle all packaging materials Check that the range is level See the Level Range section Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by shipping material Dry thoroughly with a soft cloth For more information see the Range Care section of the Use and Care Guide Read the Use and Care Guide Turn on surface burners and oven See the Use and Care Guide for specific instruction on range operation If range does not operate check the following 9V DC alkaline battery is installed correctly 9V DC alkaline battery is not defective or discharged 9V DC alkaline battery is connected See the Troubleshooting section of the Use and Care Guide When the range has been on for 5 minutes check for heat If the range is cold turn off the range and check that the gas supply line shutoff valve is open m If the gas supply line shutoff valve is closed open it then repeat the 5 minute test as outlined above m If the gas supply line shutoff valve is open turn to closed position and contact a qualified technician If you need Assistance or Service Please reference the Assistance or Service section of the Use and Care Guide or contact the dealer from whom you purchased your range 13
14. f children Reinstall the battery when the range will be used again NOTE Remove the battery before moving the range Reinstall the battery after the range has been reconnected While a knob is in the Then LITE position if Battery status lightis OFF The range is operating normally and igniters spark Battery status light is ON and igniters spark Change battery soon Battery status light is ON and igniters do not spark Change battery now Battery status light is OFF and igniters do not spark Change battery now or check to ensure battery is installed correctly Initial lighting and gas flame adjustments Cooktop and oven burners use electronic igniters in place of standing pilots When the cooktop control knob is turned to the LITE position the system creates a spark to light the burner This sparking continues until the control knob is turned to the desired setting When the oven control knob is turned to the LITE position the system creates a spark to light the pilot The oven bottom has a hole to view the pilot If the pilot is already lit turn the oven control knob counterclockwise to completely light the oven burner The electronic ignition system requires a 9V DC alkaline battery to create a spark to light the burners this battery is not included 11 Check Operation of Cooktop Burners If control panel and knobs were removed earlier reinstall knobs Push in and turn each surface unit
15. in the wall or floor where range is to be installed must be sealed Do not seal the range to the side cabinets Cabinet opening dimensions that are shown must be used Given dimensions are minimum clearances m The anti tip bracket must be installed To install the anti tip bracket shipped with the range see Install Anti Tip Bracket section m Grounded electrical supply is required See Electrical Requirements section Proper gas supply connection must be available See Gas Supply Requirements section m Contact a qualified floor covering installer to check that the floor covering can withstand at least 200 F 93 C m Use an insulated pad or 1 4 0 64 cm plywood under range if installing range over carpeting IMPORTANT To avoid damage to your cabinets check with your builder or cabinet supplier to make sure that the materials used will not discolor delaminate or sustain other damage This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194 F 90 C Mobile Home Additional Installation Requirements The installation of this range must conform to the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 When such standard is not applicable use the Standard for Manufactured Hom
16. ly line rs m A 1 3 cm male pipe thread is needed for connection to the female pipe threads of the inlet to the appliance pressure regulator m Do not kink or damage the flexible metal tubing when moving the range Rigid pipe connection The rigid pipe connection requires a combination of pipe fittings to obtain an in line connection to the range The rigid pipe must be level with the range connection All strains must be removed from the supply and fuel lines so range will be level and in line m Must include a shutoff valve The supply line must be equipped with a manual shutoff valve This valve should be located in the same room but external to the range opening such as an adjacent cabinet It should be in a location that allows ease of opening and closing Do not block access to shutoff valve The valve is for turning on or shutting off gas to the range A Gas supply line B Shutoff valve open position C To range Gas Pressure Regulator The gas pressure regulator supplied with this range must be used The inlet pressure to the regulator should be as follows for proper operation Natural gas Minimum pressure 5 WCP Maximum pressure 14 WCP LP gas Minimum pressure 11 WCP Maximum pressure 14 WCP Contact local gas supplier if you are not sure about the inlet pressure Burner Input Requirements Input ratings shown on the model serial rating plate are for elevations
17. minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet IMPORTANT If installing a range hood or microwave hood combination above the range follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface This range is equipped with an electronic ignition system that works with an 9V DC alkaline battery not included See the Installing Replacing Battery section for instructions on installing and replacing the battery AWARNING Explosion Hazard Use a new CSA International approved gas supply line Install a shut off valve Securely tighten all gas connections If connected to LP have a qualified person make sure gas pressure does not exceed 14 36 cm water column Examples of a qualified person include licensed heating personnel authorized gas company personnel and authorized service personnel Failure to do so can result in death explosion or fire Observe all governing codes and ordinances IMPORTANT This installation must conform with all local codes and ordinances In the absence of local codes installation must conform with American National Standard National Fuel Gas Code ANSI 2223 1 latest edition IMPORTANT Leak testing of the range must be conducted according to the manufacturer s instructions Type of Gas Natural gas This range is design certified by CSA I
18. ncounter immediate resistance the range foot is engaged in the anti tip bracket 3 If the rear of the range lifts more than 2 1 3 cm off the floor without resistance stop tilting the range and lower it gently back to the floor The range foot is not engaged in the anti tip bracket IMPORTANT If there is a snapping or popping sound when lifting the range the range may not be fully engaged in the bracket Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket Verify that the bracket is held securely in place by the mounting screws 4 Slide the range forward and verify that the anti tip bracket is securely attached to the floor or wall 5 Slide range back so the rear range foot is inserted into the slot of the anti tip bracket IMPORTANT If the back of the range is more than 2 5 1 cm from the mounting wall the rear range foot may not engage the bracket Slide the range forward and determine if there is an obstruction between the range and the mounting wall Changes to the gas supply must be performed by a qualified service technician If you need assistance or service refer to the Assistance or Service section of the Use and Care Guide for contact information Repeat steps 1 and 2 to ensure that the range foot is engaged in the anti tip bracket If the rear of the range lifts more than 12 1 3 cm off the floor without resistance
19. nternational for use with Natural gas or after proper conversion for use with LP gas m This range is factory set for use with Natural gas See Gas Conversions section The model serial rating plate located on the oven frame behind the left side of the broiler door has information on the types of gas that can be used If the types of gas listed do not include the type of gas available check with the local gas supplier LP gas conversion Conversion must be done by a qualified service technician No attempt shall be made to convert the appliance from the gas specified on the model serial rating plate for use with a different gas without consulting the serving gas supplier See Gas Conversions section Gas Supply Line m Provide a gas supply line of 34 1 9 cm rigid pipe to the range location A smaller size pipe on longer runs may result in insufficient gas supply With LP gas piping or tubing size can be 2 1 3 cm minimum Usually LP gas suppliers determine the size and materials used in the system NOTE Pipe joint compounds that resist the action of LP gas must be used Do not use TEFLON tape T TEFLON is a registered trademark of E l Du Pont De Nemours and Company 6 Flexible metal appliance connector m If local codes permit a new CSA design certified 4 5 ft 122 152 4 cm long 1 3 cm or 34 1 9 cm I D flexible metal appliance connector may be used for connecting range to the gas supp
20. ssure regulator in the broiler A Gas pressure regulator IMPORTANT Do not remove the gas pressure regulator 2 Check that the gas pressure regulator shutoff valve is in the ON position a N es I Oe lie k S fN Front View O at Front Side View Shutoff valve ON Position 3 Open the manual shutoff valve in the gas supply line The valve is open when the handle is parallel to the gas pipe ee A Closed valve B Open valve 4 Test all connections by brushing on an approved noncorrosive leak detection solution Bubbles will show a leak Correct any leak found 5 Close the broiler door 6 Remove cooktop burner caps and grates from parts package Align notches in burner caps with pins in burner base Burner caps should be level when properly positioned If burner caps are not properly positioned surface burners will not light Place burners burner caps and grates on the cooktop 1 Place the outside of your foot against the bottom front of the broiler and grasp the lower right or left side of the control panel as shown NOTE If your countertop is mounted with a backsplash it may be necessary to grasp the range higher than is shown in the illustration 2 Slowly attempt to tilt the range forward If you e
21. st secure the range to the floor 3 Determine and mark centerline of the cutout space The mounting can be installed on either the left side or right side of the cutout Position mounting bracket against the wall in the cutout so that the V notch of the bracket is 7 20 cm from centerline as shown AWARN 1 NG B Centerline A Explosion Hazard 7 SP Use a new CSA International approved gas supply line ka Install a shut off valve l Securely tighten all gas connections A 77 20 cm If connected to LP have a qualified person make sure B Bracket V notch gas pressure does not exceed 14 36 cm water column 4 Drill two 3 mm holes that correspond to the bracket aa 3 holes of the determined mounting method See the following Examples of a qualified person include illustrations licensed heating personnel Floor Mounting authorized gas company personnel and authorized service personnel Failure to do so can result in death explosion or fire Typical rigid pipe connection A combination of pipe fittings must be used to connect the range to the existing gas line Your connections may be different according to the supply line type size and location 1 Apply pipe joint compound made for use with LP gas to all pipe thread connections 2 Using a pipe wrench to tighten connect the gas supply to the Wall Mounting range af m UCH Rear position Front position Diagonal 2 options
22. t in 20 40 seconds this delay is normal The oven valve requires a certain time before it will open and allow gas to flow To avoid damaging the oven igniter system do not insert any object into the electrode system Do not clean that area 3 Check the oven burner for proper flame The flame should be v2 0 13 cm long with inner cone of bluish green The outer mantle should be dark blue and should be clean and soft in character No yellow tips not enough air blowing or lifting too much air of flame should occur If the flame needs adjusting 1 Turn the oven off Wait for the oven burner to cool down 2 Open oven door and remove oven racks oven tray and flame spreader and set aside A Oven tray lift up at area shown to remove B Screws C Flame spreader 3 Locate the air shutter near the rear wall of oven and loosen the shutter screw A Shutter screw B Air shutter 4 Adjust the air shutter 5 Turn the oven back on and check for proper flame If the flame is still not properly adjusted turn the oven off wait for the oven burner to cool down and repeat Step 4 until flame is properly adjusted 10 When the flame has been properly adjusted turn the oven off and wait for the burner to cool down Tighten the shutter screw Reinstall flame spreader and oven tray Reinstall the oven racks Close the oven door Close the broiler door ok a PON Ch
23. tighten Place LP gas oven burner spud in plastic parts bag along with LP gas cooktop burner spuds for future use and keep with the bag containing literature Reinstall oven burner Reinstall oven racks oven tray and flame spreader 18 o Refer to the Make Gas Connection section for properly connecting the range to the gas supply Turn the manual shutoff valve in the gas supply line to the open position Refer to Check Operation of Cooktop Burners in the Electronic Ignition System section for proper burner ignition operation and burner flame adjustments IMPORTANT You may have to adjust the Lo setting for each cooktop burner Checking for proper cooktop and oven burner flames is very important The small inner cone should have a very distinct blue flame 1 4 to 2 0 6 cm to 1 3 cm long The outer cone is not as distinct as the inner cone Natural gas flames do not have yellow tips Close the oven door and turn the knob to the OFF position Refer to the Complete Installation section to complete this procedure 19 W10531342A 2012 Whirlpool Corporation 9 12 All rights reserved Printed in Mexico
24. tray and flame spreader and set aside Lift oven burner The orifice spud is behind the oven burner air shutter A Oven burner B Air shutter Locate LP gas orifice soud stamped 58 in the package containing literature supplied with the range Use a 3 combination wrench and remove the Natural gas orifice spud Install the number 58 LP gas spud IMPORTANT Do not overtighten OD A LP oven orifice spud stamped with 58 Place Natural gas oven burner spud in plastic parts bag along with Natural gas cooktop burner spuds for future use and keep with the package containing literature Reinstall oven burner Reinstall oven racks oven tray and flame spreader Refer to the Make Gas Connection section for properly connecting the range to the gas supply Turn the manual shutoff valve in the gas supply line to the open position Refer to Check Operation of Cooktop Burners in the Electronic Ignition System section for proper burner ignition operation and burner flame adjustments IMPORTANT You may have to adjust the Lo setting for each cooktop burner Checking for proper cooktop and oven burner flames is very important The small inner cone should have a very distinct blue flame 1 4 to 2 0 6 cm to 1 3 cm long The outer cone is not as distinct as the inner cone LP gas flames have a slightly yellow tip Close the oven door and turn the knob to the OFF position
25. up to 2 000 ft 609 6 m For elevations above 2 000 ft 609 6 m ratings are reduced at a rate of 4 for each 1 000 ft 304 8 m above sea level Gas Supply Pressure Testing Gas supply pressure for testing regulator must be at least 1 water column pressure above the manifold pressure shown on the model serial rating plate Line pressure testing above 1 2 psi gauge 14 WCP The range and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of psi 3 5 kPa Line pressure testing at 1 2 psi gauge 14 WCP or lower The range must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than psi 3 5 kPa INSTALLATION INSTRUCTIONS AWARNING Excessive Weight Hazard Use two or more people to move and install range Failure to do so can result in back or other injury 1 Do not use oven door handle to lift or move the range 2 Remove shipping materials tape and film from range Keep cardboard bottom under range 3 Remove oven racks and parts package from inside oven 4 To place range on its back take 4 cardboard corners from the carton Stack one cardboard corner on top of another Repeat with the other 2 corners Place them lengthwise on the floor behind the range to s
26. upport the range when it is laid on its back 5 Using 2 or more people firmly grasp the range and gently lay it on its back on the cardboard corners 6 Pull cardboard bottom firmly to remove 7 Use an adjustable wrench to loosen the leveling legs Adjust the leveling legs to the correct height Leveling legs can be loosened to add up to a maximum of 1 2 5 cm A minimum of 746 0 5 cm is needed to engage the anti tip bracket NOTE If height adjustment is made when range is standing tilt the range back to adjust the front legs then tilt forward to adjust the rear legs 8 Place cardboard or hardboard in front of range Using 2 or more people stand range back up onto cardboard or hardboard AWARNING Tip Over Hazard A child or adult can tip the range and be killed Install anti tip bracket to floor or wall per installation instructions Slide range back so rear range foot is engaged in the slot of the anti tip bracket Re engage anti tip bracket if range is moved Do not operate range without anti tip bracket installed and engaged Failure to follow these instructions can result in death or serious burns to children and adults 1 Remove the anti tip bracket from where it is attached inside the oven with a wire tie 2 Determine which mounting method to use floor or wall If you have a stone or masonry floor you can use the wall mounting method If you are installing the range in a mobile home you mu
27. ure included with the range Two Natural gas spuds are stamped 149 and two 125 3 Remove the LP gas orifice souds using a 7 mm combination wrench 4 Install the Natural gas orifice spuds using a 7 mm combination wrench N D B A Spud B Holder _ NOTE This range is equipped with 2 standard burners and 2 super burners Spud size and location remain the same Standard Super Burner 125 Burner 149 Super Standard Burner 149 Burner 125 S SD Q Or i NANA 5 Place LP gas orifice spuds in the parts bag for future use and keep with the package containing literature 6 Reinstall burners burner caps and burner grates 17 To Convert Oven Burner Open the oven door and remove oven racks oven tray and flame spreader and set aside Lift oven burner The orifice spud is behind the oven burner air shutter A Oven burner B Air shutter Locate Natural gas orifice spud stamped 51 in the package containing literature supplied with the range Use a combination wrench and remove the LP gas orifice spud Install the number 51 LP gas spud A Natural gas oven orifice spud stamped with 51 IMPORTANT Do not over
28. ure regulator IMPORTANT Do not remove the gas pressure regulator 4 Remove the cap from the gas pressure regulator using a flat blade screwdriver NOTE Do not remove the spring beneath the cap A Cap 5 Turn the cap over so the LP is visible 6 Reinstall the cap To Convert Surface Burners 1 Remove burner grate burner caps and burners A Burner cap B Burner 2 Locate LP gas orifice spuds for top burners in the literature bag included with the range Two LP gas spuds are stamped 88 and two 78 3 Remove Natural gas orifice spuds using a 7 mm combination wrench 4 Install LP gas orifice spuds using a 7 mm combination wrench ES A Spud B Holder A B NOTE This range cooktop is equipped with 2 standard burners and 2 super burners Spud size and location remain the same AN Op Super Burner 88 Standard Burner 78 Standard Burner 78 Super Burner 88 5 Place the Natural gas orifice spuds in the parts bag for future use and keep with the bag containing literature 6 Reinstall burners burner caps and burner grates 15 To Convert Oven Burner 16 Open the oven door and remove oven racks oven
Download Pdf Manuals
Related Search