Weider CSWB2 User's Manual
Contents
1. CSWB2 REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN ST WOODLAND HILLS CA U S A 91367 TABLE OF CONTENTS gt a e Diagram Parts List POE Repair Parts and Service Step 1 Frame Assemb Step 2 Backrest Step 3 Seat mee Step Leg Curl Assembly Step 5 Adjustable Uprights n Fy Y PARTS LIST 10 04 89 i 77 F HAE A DIAGRAM ORDERING ua NO PART NAME 3 ONO 1 UPRIGHT c0253 C17 gt 1 2 dE C0253 C17 I BASE FRAME 0143 29 UPPER U FRAME 1 C0144 C29 SEAT 1 x 6 I BACKREST LONG ANGLE IRON 2 2 30 Fom BaD Ts ADJUSTABLE UPRIGHT 2 0254 017 BACKREST ADJ BAR 1 FERGEN 2 mn HARDWARE BAG 1 A 5 16 20 X 2 HEX HEAD BOLT B 5 16 20 X 2 1 2 HEX HEAD BOLT 801s 5 16 20 LOCK NUT D 3 8 16 X 2 1 2 HEX HEAD BOLT 1 E 3 8 16 LOCK NUT 1 SSCS 1 4 20 X 3 4 MACHINE SCREW 6 HH 5022 G 1 1 4 20 X 2 MACHINE SCREW 1 I uH 5256 gt gt i AA 8001 AA 8002 1 1 2 SQUARE PLASTIC CAP 2 SQUARE PLASTIC CAP 1 ROUND PLASTIC CAP AA 8005 M COVER CAP AA 8070 3 4 ROUND PLASTIC CAP AA 8004 LOCKING PIN LARGE WW 7017 i _1__ j W 7017 R O LOCKING PIN SMALL 2 ww 7016 x s 5 16 20 X 2 1 4 HEX HEAD BOLT 2 HH 5035 UPRIGHT DECAL 2 DE 4100 C INSTRUC2. BOLTS B and LOCK NUTS C Make sure all bolts are tight Insert 3 SQUARE PLASTIC CAPS H into BASE FRAME 3 and 1 SQUARE PLASTIC CAP H into front of MAIN FRAME 2 between the leg curl brackets STEP 2 BACKREST ASSEMBLY LONG ANGLE IRONS 8 are pre assembled to BACKREST 6 so it is necessary to remove one MACHINE SCREW F from the end of one angle iron and spread apart enough to allow the backrest to be assembled onto pivot rod of MAIN FRAME 2 Close angle irons over pivot rod and secure loosened angle iron with MACHINE SCREW F that was previously removed STEP 3 SEAT ASSEMBLY Align bolt holes of SEAT 5 with holes on MAIN FRAME 2 SECURE WITH 2 MACHINE SCREWS f through brackets and 1 MACHINE SCREW 6 through frame STEP 4 LEG CURL 2 Insert SQUARE PLASTIC CAPS H into both ends of LEG CURL 7 Insert 2 ROUND PLASTIC CAPS into both ends of PAD BAR 9 Assemble FOAM PAD 10 onto one end of PAD BAR 9 and insert PAD BAR 9 through proper hole in LEG CURL 7 Assemble other FOAM PAD 10 onto PAD BAR 9 The use of a small amount of liquid dish detergent wiped along the surface of the pad bar wi make assembling pads easier and wi act aS an adhesive when it dries Insert ROUND PLASTIC CAP K into weight pin on LEG CURL 7 and assem ble COVER CAP M over the rear extended section of the weight pin Place the completed leg curl between brackets on MAIN FRAME 2 and se
3. TION MANUAL CNN 1079 br 2 H NS HEN T PREASSEMBLED WITH BACKREST amp SEAT FEET EE FN REPAIR PARTS AND SERVICE ALL OF THE PARTS FOR THE WEIGHTBENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SERVICE DEPT 900 WEST ST JOHN ST OLNEY ILL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT IF YOU FIND THIS PRODUCT TO HAVE EITHER A DEFECTIVE PART OR A MISSING PART WRITE THE ABOVE ADDRESS OR PHONE CUSTOMER SERVICE 4 800 225 0653 ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO NAME OF PART G 2RDERING NUMBER CSWB2 2 STEP 1 FRAME ASSEMBLY ALIGN u brackets of MAIN FRAME 2 with holes on BASE FRAME 3 Secure with 2 HEX HEAD BOLTS O and 2 LOCK NUTS C Align bolt holes of UPPER U FRAME 4 with holes on bracket of MAIN FRAME 2 Secure with 2 HEX HEAD BOLTS A and 2 LOCK NUTS C Insert 2 SQUARE PLASTIC CAPS J into end of UPRIGHTS 1 Align bolt holes of each UPRIGHT with bolt holes on brackets of BASE FRAME 3 and UPPER U FRAME 4 Secure each with 3 HEX HEAD BOLTS B and 3 LOCK NUTS C Insert 2 ROUND PLASTIC CAPS K into each end of WEIGHT STACK PIN 12 Slide WEIGHT STACK PIN 12 into lower hole in UPRIGHTS 1 and assemble with HEX HEAD
4. cure with HEX HEAD BOLT D and LOCK NUT E Do not overtighten The leg curl should swing in a free motion The leg curl can be held from pivoting by the use of the LOCKING PIN P when assembled through the hole in the lower section of the LEG CURL 7 and around the front frame of MAIN FRAME 2 V r NZ STEP 5 ADJUSTABLE UPRIGHTS Insert ROUND PLASTIC CAPS K into each end of BACKREST ADJ BAR 13 This bar is used to support the backrest and adjust the incline or decline for various types of exercise The height of the bar holders can be ad usted by inserting ADJUSTABLE UPRIGHTS 91 into UPRIGHTS 1 and pinning into the desired height by using LOCKING PINS WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT IS ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER IT IS RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORK OUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED
Download Pdf Manuals
Related Search