Weider B120 User's Manual
Contents
1. 8005 H GT ENES NE UR Ass ve 1 2 SQUARE PLASTIC CAP 2 AA 8001 Te 1 1 40 SQUARE PLASTIC CAP 1 3 AA 8069 x q SEK CUT LOCK NUTS o il R 5 16 20 x 2 HEX HEAD BOLT 5 HH 5021 ERIS _ _ 5 16 20 LOCK NUT C k 1 4 20 x 3 4 MACHINE SCREW 5 16 20 x 2 1 4 HEX HEAD BOLT UPRIGHT DECAL RIGHT UPRIGHT DECAL LEFT INSTRUCTION MANUAL 965 E NE spa2. NN 1048 ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN STREET WOODLAND HILLS CALIFORNIA U S A 91367 TABLE OF CONTENTS ETNE ETE MGE REPAIR PARTS AND SERVICE Br FN PARIS NNN STEP 1 FRAME ASSEMBLY MN ENDE CIEN NE C C MENS DECAL APPLICATION 58 U MENFE ee Ur uu ccce s a ERE ENGE a oe 2 DM RM M EDU 2 ES NN EEE l NN RUE po Uu e x i A REPAIR PARTS AND SERVICE All of the parts for the Weightbench can be ordered from Weider Health and Fitness Parts Service Dept 900 West St John St Olney 62450 When ordering parts will be sent and billed at the current prices Prices may be subject to change without notice Standard hardware items are available at local hardware stores If you find this product to have either defective part or a miSsing part write the above address or for faster service phone Customer Service at 1 800 423 5502 ALWAYS include the following information when ordering parts eModel Number eName of Part e Ordering Number B 120 NO ds S r ERE a O BEEN CEN JERN 277 PARTS LIST PART NAME Our MAIN FRAME m FRONT SUPPORT LEG CURL 7 20 BACKREST 2 PAD BAR 30 FOAM PAD BACKREST ADJ BAR 20 LONG ANGLE IRON Q 5 6 20 X2 HEX HEAD BOLT Q 2 1 4 20 3 4 MACHINE SCREW 2 UPRIGHT DECAL RIGHT 7 UPRIGHT D
3. ECAL LEFT Q INSTRUCTION MANUAL NO REQUIRED 19 3 ORDERING NUMBER CA05 0205 CA05 0107 05 0108 05 0109 05 0314 05 0315 05 6044 05 0425 CA05 6045 CA05 6046 CA05 5777 8004 8005 8070 AA 8001 8069 24 063 HH 5061 HH 5043 HH 5013 HH 5017 HH 5021 HH 502 DE 4012 DE 4013 IN2588 STEP 1 FRAME ASSEMBLY Begin by inserting 2 SQUARE PLASTIC CAPS d into UPRIGHT 1 Align bolt holes on L BRACKETS 11 with bolt holes on UPRIGHT 1 Secure each bracket with 2 HEX HEAD BOLTS h and 2 LOCK NUTS j Align bolt hole on MAIN FRAME 2 and FRONT SUPPORT 3 Secure with 1 HEX HEAD BOLT h and 1 LOCK NUT j With UPRIGHT 1 standing lower u bracket of MAIN FRAME 2 onto crossmember of UPRIGHT 1 Align bolt holes and secure with 2 HEX HEAD BOLTS m and 2 LOCK NUTS j Insert 2 SQUARE PLASTIC CAPS e into FRONT SUPPORT 3 Tighten all bolts LOOSEN NOTE The lower or attach 10R 2 TURN ment end of the BACKREST 5 can be identified quickly by the LONG ANGLE IRONS 10 The LONG ANGLE IRONS 10 will be extended approximately two inches beyond the BACKREST PAD 5 STEP 2 BACKREST PREPARATION Turn BACKREST 5 over to expose work area Both LONG ANGLE IR NS 10 have been fastened to BACKREST 5 for shipment One long angle iron must be loosened in order to assemble BACKREST 5 to main frame pivot rod The lower MACHINE SCREM k mus
4. l Place COVER CAP c over weight pin opposite end WARNING CONSULT YOUR PHYSICIAN CONSULT YOUR PHYSICIAN BEFORE STARTING YOUR EXERCISE PROGRAM IT IS ADVISABLE TO HAVE A PHYSICAL EXAMINATION BY YOUR PHYSICIAN BEFORE YOU ENTER ANY EXERCISE PROGRAM I FOR YOUR OWN SAFETY DO NOT BEGIN ANY EXERCISE WITHOUT PROPER INSTRUCTION CHILDREN AND HANDICAPPED PERSONS SHOULD NOT USE ANY EXERCISE EQUIPMENT WITHOUT A QUALIFIED PERSON IN ATTENDANCE TRAIN WITH A PARTNER IT IS RECOMMENDED THAT AN INDIVIDUAL SHOULD NOT WORKOUT WITHOUT A TRAINING PARTNER IN ATTENDANCE SET UP YOUR PROGRAM TO ACCOMMODATE TWO PEOPLE AND YOU WILL BE HIGHLY MOTIVATED TO INSURE PROPER CLEARANCE BETWEEN THE MAST AND LEG CURL MOUNTING BRACKETS 8 FLATWASHERS HAVE BEEN ADDED TO THE HARDWARE ASSEMBLE TWO WASHERS BETWEEN THE LEG CURL BRACKET AND THE LEG CURL AT THE ATTACHMENT HOLES SHOWN ABOVE J 2252 PARTS LIST 11 22 88 DIAGRAM PART NAME ORDERING pU S meer gt gt NT 00550205 x 2 MAIN FRAME 4 405 0107 3 O FRONT SUPPORT 4 CAOS 0108 Venn 1 040830102 c8 TU BACKREST gt 5 NE 005500 ae D F Lu V PRE ER LONG ANGLE IRON 05 6046 i O 2 L BRACKET CA05 6124 EE Vr D V AEK EET Je EEE x a 3 4 ROUND PLASTIC CAP 1 4 AA 8004 P p 1 ROUND PLASTIC f
5. t be removed while the upper MACHINE SCREW k is only loosened The LONG ANGLE IRON 10 can now swing freely from the lower end of BACKREST 5 3 te STEP 3 ATTACHING BACKREST amp SEAT BACKREST To aid in attaching Backrest first slide the BACKREST ADJ BAR 9 through one of the hole patterns in the uprights With LONS ANGLE IRON 10 free lower BACKREST 5 to main frame pivot rod Slide the secured LONG ANGLE IRON 10 onto one side of pivot rod Swing the free LONG ANGLE IRON 10 back to its original position and onto the opposite end of the pivot rod See Detail A Replace MACHINE SCREM k that was removed in Step 2 and tighten all machine screws SEAT With SEAT 6 right side up lower SEAT 6 to seat brackets on main frame Align bolt holes and fasten with 2 MACHINE SCREWS k Tighten all machine screws SEAT BRACKET LEG CURL BRACKETS STEP 4 ATTACHING LEG CURL Place LEG CURL 4 between leg curl brackets on main frame and align bolt holes Secure with HEX HEAD BOLT f and LOCK NUT g Repeat the following instructions until all PAD BARS 7 and FOAM PADS 8 are in place First slide PAD BAR 7 through proper hole in LEG CURL 4 until equal amounts of bar are on both sides of LEG CURL 4 Slide one FOAM PAD 8 onto each end of PAD BAR 7 Insert SQUARE PLASTIC CAP e into end of LEG CURL 4 Insert PLASTIC Cap b into weight pin on leg cur
Download Pdf Manuals
Related Search