Wayne-Dalton 3966 User's Manual
Contents
1. door will begin to move NOTE If you inadvertently enter an incorrect code the door will not move To Reset press and hold the 7 8 and 9 0 buttons for 2 seconds and reenter your PIN number 2 Unit remains active for next 25 sec Pressing any key will stop the door if opening and stop or reverse the door if closing Battery Replacement Under normal operating conditions the battery should be changed once every 12 months Dispose of used batteries properly To replace battery perform the following steps A Snap open case with a coin and remove old batteries B Replace batteries two CR2032 or equivalent and snap case together 2 Coin Cells Batteries CR2032 Rear Case Coin Slot MODEL 3966 Wireless Keyless Entry System Your new Model 3966 Wireless Keyless Entry contains a state of the art wireless digital transmitter capable of operating an unlimited number of compatible garage door openers For added security your Wireless Keyless Entry utilizes a rolling code technology that each time the transmitter communicates with the receiver sets a new code selecting from millions of combinations reducing the possibility of electronic equipment causing unwanted access For proper operation it is important that you follow the programming directions and sequence as written Wayne Dalton Corp One Door Drive m Mt Hope OH 44660 888 827 3667 Wayne Dalton START HERE ae PLEASE R2. EAD ALL INSTRUCTIONS THOROUGHLY TO FAMILIARIZE YOURSELF WITH THE PROGRAMMING PROCEDURE BEFORE BEGINNING SAVE THESE INSTRUCTIONS FOR REFERENCE WHENEVER YOU WISH TO CHANGE YOUR PERSONAL IDENTIFICATION NUMBER PIN Before your Wireless Keypad will be able to operate the opener there are several programming steps that have to be completed FCC WARNING To comply with FCC rules adjustment or modification of transmitter is prohibited THERE ARE NO USER SERVICEABLE PARTS EXCEPT FOR BATTERY REPLACEMENT This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation A WARNING Always keep moving door in sight and away from people and objects until it is completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR Never let children operate or play with door controls Keep all controls away from children Programming or Changing Personal Identification Number program button program button program button CGarive DoorMaster ClassicDrive A With new installations it is recommended that the keyless entry be programmed before mounting to wall otherwise proceed to step B B Unit should be programmed with garage door in the down position For the iDrive IM openers pull the emergency disconne
3. Pre drill a 5 64 pilot hole 3 4 deep NOTE This equipment has been tested and found to comply with the limits for a Class B digital device Pursuant to Part 15 of the FCC Rules These limits are l designed to provide reasonable protection against pi ae harmful interference when the equipment is operated in z a residential environment This equipment generates q l uses and can radiate radio frequency energy and if l Not installed and used in accordance with the i l i i l instruction manual may cause harmful interference to l radio communications However there is no guarantee l that interference will not occur in a particular l installation If this equipment does cause harmful l interference to radio or television reception which can l i l be determined by turning the equipment off and on the user is encouraged to try to correct the interference by i one or more of the following measures Reorient or relocate the receiving antenna z Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected j Consult the dealer or an experienced radio TV z technician for help Pre drill a 5 64 pilot hole 3 4 deep Drilling Template For Keyless Entry Mounting NOTE With new installations it is recommended that the keyless entry be programmed before mounting to wall Lo
4. cate Keyless Entry Unit within sight of door at a minimum height of 5 feet so it cannot be reached by small children and away from all moving parts of the door Choose a convenient location that does not interfere with the normal opening and closing operation of the door such as the door jamb IS CAUTION The keypad should be mounted a minimum of 5 feet from the floor to keep it out of the reach of small children Two screws are included for proper mounting into wood or other similar material If you re mounting into some other material consult a building contractor to insure proper hardware is used for a secure mounting Once you have determined the mounting location use the drilling template ermine le positions and drill a 5 64 pilot hole 3 4 deep for the two mounting screws Snap open the Keyless Entry case with a coin Separate the front case from the back case Mount the back case and secure with screws provided Do not over tighten the screws as this may bend or damage the back case Install and snap the front case onto the back case Remove paper backing from Changing Personal Identification Number label and apply label to a clean surface inside garage How Your Keyless Entry Operates Your Opener The following explains how your Keyless Entry can be used to OPEN CLOSE START and STOP your door 1 Enter your 5 digit PIN personal identification number
5. ct handle to the manual operated position lower position A p C Press the program button on the garage door opener to switch the opener to the transmitter learn mode see illustrations above Opener will remain in the learn mode for at least 30 seconds D Press the desired five digit PIN PERSONAL IDENTIFICATION NUMBER number example 1 2 3 4 5 Garage door opener should beep or lamp should blink For the iDrive openers return the emergency disconnect handle to the motor operated position upper position Wait 5 seconds and press any button the door should move Programming is now complete Q Cy NOTE IF AT ANY TIME AN ERROR WAS MADE IN ENTERING THE CODES SIMPLY PRESS AND HOLD BOTH THE 7 8 AND 9 0 BUTTONS FOR 2 SECONDS TO RESET THE KEYLESS ENTRY REPEAT THE ABOVE PROCEDURES Note One 3966 Keyless Entry can be programmed to open multiple garage door openers To program for additional openers repeat steps A thru D above except input a different five digit PIN number for each additional opener
Download Pdf Manuals
Related Search