Vision Fitness X1500 User's Manual
Contents
1. M8x45L Bo Quantity 2 t CO jo N M4x12L Screw Quantity 2 5x10x1T Washer Quantity 4 8x38x2T Washer Quantity 2 Q Nylon Nut Cover Quantity 2 6x14x1T Washer Quantity 8 8x25x1 5T Washer Quantity 2 CH mu M5x12L Bolt Quantity 12 Nylon Interval Ring Quantity 4 Assembly Guide X1500 ELLIPTICAL TRAINER To avoid possible damage to this Elliptical Trainer please follow these assembly steps in the correct order Before proceeding find your new Elliptical Trainer s serial number located on the front axle tube and enter here Refer to this number when calling for service and enter this serial number on your Warranty Card and in your own records Be sure to read your Owner s Guide before using your new Elliptical Trainer If any parts hardware or tools are missing please call 1 800 335 4348 NOTE It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent loosening and noise Also during each assembly step ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw e Slide the stabilizer shaft through the plastic sleeves in the rear support tube NOTE A tight fit between the shaft and sleeves is important to the stability of the unit Because of this it2. U VISIONS FITNESS 500 South CP Avenue PO Box 280 Lake Mills WI 53551 toll free 800 335 4348 phone 920 648 4090 fax 920 648 3373 www visionfitness com 2008 Vision Fitness All Rights Reserved May be covered by one or more patents or patents pending US 5540637 US 5573480 US 5813949 US 5813949 US 5924962 US 5938567 US 6135927 US 6149551 US 7316633 TW 364373 TW 371899 CN 99808486 7 9 08 AG18 34PRD REV8 X1500 ELLIPTICAL TRAINER TOOLS amp PARTS INCLUDED 5mm L Shaped Wrench PARTS BOX 13mm Wrench Console Mast Boot DualAction Link Arm Covers DualAction Axle Covers Pedal Arm Joint Covers Right and Left Footplates Rear Stabilizers Water Bottle and Cage Power Supply Color Coded Hardware Bags Owners Manual Assembly Guide Warranty Card Screwdriver 5mm TShaped Wrench 13mm Wrench Quantity 1 8x16x1T Washer NYY Quantity 2 M8x15L Bolt Quantity 2 M8x20L Bolt Quantity 2 l SW8 Lock Washers Quantity 6 m M8X1 5L Bolt 8x18x1T Washer Quantity 6 Quantity 4 l 4x10x1T Washer Quantity 2 8x17x1T Arc Washer Quantity 2 25x34x2T Wavy Washer Quantity 2 mm M8x20L Bolt Quantity 2 P mu M4x12L Bolt Quantity 2 8x38x2T Washer Quantity 2 D 5 25x34x2T Wavy Washer Quantity 2 M8 Nut Quantity 4 OL SS41 Link Joint Sleeve Quantity 2 NII
3. Slide a wavy washer 25x34x2T onto the console mast axle Slide th right duataction arm onto the axle Fi in place with a washer 8x38x2T and nylon nut M8 Cover with the included nylon nut cover e Insert the link joint sleeve SS41 into the socket joint of the right link arm Position the socket joint of the link arm into the bracket at the bottom of the duakaction arm Position the Nylon Interval Rings between the socket joint and bracket on each side Insert a bolt M8x45L through the bracket interval rings and socket joint sleeve Secure in place with a washer 8x25x1 5T and nylon nut M8 Tighten with the 5mm T shaped wrench and 13mm wrench e Position the link arm covers over the socket joint and secure the two pieces together with a screw M4x1 21 Tighten with the screwdriver Connect the cover to each side of the link arm with a washer 5x1Ox1T and bolt M5x12L Tighten with the screwdriver e Position the right footplate onto the right link arm Secure in place with four washers 6x14x1T and four bolts M5x1 21 Tighten with the screwdriver e Repeat steps on the left side e Attach the hand grips onto the dual action arms by turing grip in a clockwise direction Make sure it is tight
4. may be helpful to tap the shaft through with a rubber mallet e Slide the stabilizer covers onto the stabilizer shaft and secure with M8x20L bolts and 8x16x1T _ flat washers Tighten with the 5mm Tshaped wrench e Attach end caps to the end of the guide rails with M8x151 bolts Tighten with the 5mm Tshaped wrench BLUE BAG e Slide a wavy washer 25x34x2T on to the right rotation axle Slide the knuckle joint of the pedal arm assembly onto the right rotation axle The pedal arm roller wheel should be placed into the groove of the guide rail Secure the pedal arm assembly to the rotation axle with a washer 8x38x2T and bolt M8x2OL U with the 5mm TF shaped wrench e Place the pedal arm cover over the knuckle joint Secure in place with a washer 4x10x1T and bolt M4x1 21 Tighten with the screwdriver e Repeat both steps on the left side Stabilizer Cover Knuckle Joint Pedal Arm Assembly Pedal Arm Cover Hand Grips CONSOLES DELUXE PREMIER Dual Action Axle Cover Hand Grips Dual Action Arm Link Arm Covers Console CONSOLE e Refer to Product Selection and Model Configuration decal on console or follow these steps e Once the product is plugged in turn on the console e Select product Bike BK or Elliptical EP using the resistance arrow keys Press ENTER to select e Select model number Bike 1500 2050 2250 3200 or Elliptical 1500
5. 6000 6200 using the RESISTANCE arrow keys Press ENTER to select Console will reset to startup screen e The product selection and model configuration is now complete STEP 4 e Slide the boot onto the console mast e Unfold the wire harness located in the frame bracket Wrap the end of the wire tie located at the bottom of the console mast around the end of the wire harness Pull the wire tie and wire harness up through the console mast while simultaneously sliding the mast over the frame e Slide a lock washer SVW8 followed by a flat washer 8x18x1T onto four of the bolts M8x15L Insert these bolts through the side of the mast to secure the mast to the frame Slide a lock washer SVV8 followed by a arc washer 8x17x1T onto the two remaining bolts M8x15l Insert these bolts through the holes in front of the mast Tighten all bolts with the 5mm T shaped wrench e Slide the boot down the console mast and set it in place over the side covers e Remove the four bolts from the back of the console Connect the wire harness to the plug in the back of the console Connect the heart rate wires into the heart rate plugs in the back of the console Attach the console to the console mast with the four console bolts and screwdriver Attach the water bottle cage to the console mast with the two bolts located on the mast GREEN BAG e Slide the dualaction axle cover into place over the console mast axle
Download Pdf Manuals
Related Search