Home
Verilux VD03 User's Manual
Contents
1. 5 Plug ballast into a standard 120V 50 60Hz outlet Turn lamp on The green LED indicator on center of the ballast should be illuminated Fig 4 If the LED indicator does not illuminate please refer to the troubleshooting section of this manual See page 9 6 If bulb does not illuminate instantly please refer to the troubleshooting section of this manual 7 Adjust lamp brightness to the desired level low medium high WARNING Do not block vents on ballast Vents are necessary for proper function of the ballast blocking them may cause overheating of the ballast and increase risk of fire Attention a Lift your lamp by the vertical shaft V ADJUSTING THE HERITAGE DESK LAMP The Heritage Desk Lamp D adjusts several ways 1 To adjust lamp height hold lamp arm with one hand loosen center swivel knob E Raise or lower lamp arm D to desired height Tighten knob Fig 5 Fig 5 Swivel Knob To adjust lamp head angle up or down loosen swivel knob counterclockwise place head at desired angle tighten swivel knob to f 7 secure Fig 6 Fig 6 3 To tilt lamp head toward you or away from you simply move head to desired position Fig 7 Fig 7 BULB REPLACEMENT INSTRUCTIONS Removal 1 Unplug lamp from power source 2 To access the bulb remove Optix glare control filter by depressing the th
2. abrasive cleaner and soft cloth When cleaning make sure you have turned off and unplugged the unit and allowed sufficient time for the unit to cool All liquid should be properly wiped away and dried prior to restoring power DO NOT USE SOLVENTS OR CLEANERS CONTAINING ABRASIVES OR AMMONIA BASED CLEANERS Note Do not use any cleaning agents including window cleaner on the Optix glare control filter If needed dust with a clean dry cloth 10 Please visit our web site at www Verilux com NET IUX LIFE IN A BETTER LIGHT 340 Mad River Park Waitsfield VT 05673 1 888 544 4865 Printed in China for Verilux Inc VD09 MAN Rev3 O Copyright 2008 Verilux Inc All rights reserved
3. TION Insert plug securely into wall outlet Is the bulb old Check the bulb for blackening darkening at the ends an indicator of bulb life and replace bulb Is the bulb connected securely to the socket Be sure the bulb is securely seated into the socket repeat the bulb installation process Blackening darkening at ends of bulb Is the bulb new Sometimes when a new bulb is turned on for the first time the tube will darken but this will fade after a few minutes Is the bulb old With older bulbs darkening of the tube indicates end of bulb life This doesn t affect operation except to reduce the amount of light available since the phosphor in that area has become inactive Bulb replacement is recommended Light flickers Has the plug come loose Insert plug securely into wall outlet Is the bulb connected securely to the socket Be sure the bulb is securely seated into the socket repeat the bulb installation process Is the lamp connected to a dimmer switch Connect lamp plug only to wall outlet without a dimmer switch WARNING Do not block vents on ballast Vents are necessary for proper function of the ballast blocking them may cause overheating of the ballast and increase risk of fire CARE amp CLEANING Your desk lamp is made from high quality materials that will last for many years with minimum care You may want to periodically clean the lamp using a mild non
4. embling your lamp e Unplug from electrical outlet during lightning storms to ensure protection of the electronics GETTING STARTED Main Parts amp Controls A Lamp Head Switch Lamp Head Swivel Knob Lamp Arm Center Swivel Knob Counter Weight Arm A Close up of Lamp Head G Vertical Shaft Lamp Base Power Cord Power Supply Ballast Optix Glare Control Filter Bulb ASSEMBLY INSTRUCTIONS Please Read Operating Instructions Carefully Before Using the Heritage Desk Lamp 1 Set lamp base on the desk and insert the counter weight arm F onto the center swivel E and screw clockwise to tighten Fig 1 2 To lift lamp head loosen swivel knob C adjust head to desired angle Tighten swivel knob 3 Attaching the Optix glare control filter e Remove glare control filter from protective plastic bag Take care to hold filter by the edges only e Insert tabs on bottom of filter into opening Fig 2 e Press into place using thumb tab Do not touch or press on the filter material itself C E ji Fig 1 Note Do not touch material Fig 2 ASSEMBLY INSTRUCTIONS cont 4 Attach the ballast to the power cord Use care to align the 4 pin plug properly DO NOT FORCE the 4 pin plug was designed to fit in only one orientation Fig 3
5. i LIFE IN A BETTER LIGHT Heritage ccuxe EE Natural Spectrume Desk Lamp IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Thank you for purchasing the Heritage Natural Spectrum Deluxe Desk Lamp Please read the following safety information before using To reduce the risk of fire electrical shock or injury to persons e Do NOT dismantle e Do NOT alter power cord e Turn off unplug and allow to cool before replacing bulb or cleaning For indoor use only e The lamp is an electrical device DO NOT USE NEAR WATER GENERAL PRECAUTIONS e Before plugging in the lamp check to make sure the voltage corresponds with the main voltage of your location 120 volts e Do not use the lamp outside or in wet locations such as bathrooms It is intended for indoor dry use only Not for use with light dimmers timers motion detectors or extension cords e This product may cause interference with radios cordless telephones or devices that use a wireless remote control such as televisions If interference occurs move the product away from the device plug the product or device into a different outlet or move the lamp out of the line of sight of the remote control receiver The light bulb may become loose during transit To reinstall the light bulb see the bulb installation instructions on page 8 e Do NOT use lubricating agent in assembly please see troubleshooting section if you are having difficulty ass
6. umb tab and lifting it out 3 Firmly hold bulb base B and pull bulb C from the socket A in an outward motion Fig 8 Installation 1 Unplug lamp from power source 2 Firmly hold base B and push bulb C into the socket A 3 Be sure bulb is firmly seated in the socket see below and snapped into the metal bulb clip D Fig 9 4 Replace Optix glare control filter es No gap Correctly seated bulb Incorrectly seated bulb TROUBLESHOOTING Your Verilux desk lamp uses advanced micro electronics to power the revolutionary Trucolite bulb These electronics are housed in a specially designed ballast located at the power plug The LED indicator light on the ballast allows you to troubleshoot any problems with the lamp s function When replacing your Verilux ballast take care to plug in the power cord properly The 4 pin plug was designed to fit in only one orientation See Assembly Instructions on page 5 Before requesting service on your Verilux lamp please check the following e Make sure all power connectors cords and plugs are inserted fully and securely e Be sure the bulb is securely seated into the socket See page 8 e Unplug the lamp for a few minutes this allows the electronics in the ballast to reset e Make sure there is power to the wall outlet or try another outlet PROBLEM Light won t come on CHECK Has the plug come loose SOLU
Download Pdf Manuals
Related Search
Related Contents
"取扱説明書" Top Buret™ - Eppendorf A SPEEDy user's guide Comcast M1057A User's Manual Copyright © All rights reserved.
Failed to retrieve file