Uniden UST-9000 User's Manual
Contents
1. C Problem There are ghost images or wavy lines on the TV screen Solution 1 Check video polarization by pressing the V H key Adjust the Skew control by pressing the or key 2 Check the channel fine tune adjustment on the TV and the channel selector to make sure it is on 3 or 4 See problem B2 3 Fine tune antenna by pressing East or West key momen tarily so that satellite position counter changes up to 10 counts mers Check the alignment of the antenna by following the steps listed in B6 and B7 5 External interference See Helpful Hints section about inteference D Problem Picture is full of snow or sparkles Weak picture Solution l Follow steps Cl C5 2 Check all cables for proper connection 3 Make sure that the Feedhorn is properly positioned Check the Feedhorn instructions 4 1 GHz cable is too long or improper cable used for length required Check cable chart Check with your Uniden dealer about a line amplifier E Problem Distorted audio or no audio Solution 1 Check volume of receiver and TV Check Mute control 2 Check program guide to make sure the correct audio fre _ quency is tuned Press the Audio 1 keys to tune a different cnp equency 3 Check audio mode and band Try a different band setting by pressing the N W key 4 If you are using the Audio Out jacks check to make sure cables are properly connected F Problem The channel number displayed does not2. Satellite Television System A complete guide to the installa tion and operation of the UST 9000 satellite receiver system uniden UST 93000 Installation and operation x Controls Functions Front Panel Controls 1 2 3 4 11 12 a a a a a Power On Off Turn the receiver on or off from this key or the same key on the remote control C Ku Band Press to select either C band or Ku band satellite signals depending on the LNB installed in your system Memo Key Press to enter satellite channel audio or other information into memory Scan Key Activates channel scan Press once to scan 2 channels per second Press for more than 1 2 second to scan 12 channels per second Press the Scan key again or any other key to stop Channel Up Down Keys Press once to change a channel Press more than 1 2 second to change 8 chan nels per second Release key to stop V H Polarity Key Press to change from horizontal to vertical or vertical to horizontal polarity Skew Adjust the skew pulse to fine tune the television picture Press or until you get the best possible picture Video Fine Primarily for Ku band reception Press and hold the or key until a Ku band channel is visible Press momentarily to fine tune the picture Some C band channeis may also need to be fine tuned by pressing the or key momentarily Audio 1 Keys Adjust the frequency of the first
3. D14 D15 D16 Audio Indicator Lights when the satellite audio mode is selected Satellite Displays the satellite letter and number selected P L Parental Lock LED Lights when a channel has been selected that is locked V and H LEDs Lights to indicate vertical or hori zontal polarity Channel Displays the selected channel number Stereo Indicator Lights to show that the selected audio is in stereo Audio 1 and Audio 2 Displays the selected audio frequencies Remote Window Receives the infrared signal from the handheld remote control ma l Nale Bottom Panel Signal Meter Adjustment if signal level on meter is consistently too high adjust level by turning control with a screwdriver SS EE S PRET E TR eRe ema ee eR ERT Rear Panel R1 s R2 R3 R4 R6 R7 R8 R9 R10 C Input F type connector for the 1 GHz IF cable from the LNB or the UST 524 multiple receiver unit Ku Input Connect the 1 GHZ IF cable from the Ku LNB for Ku band reception Descram Out F type connector for composite vid eo output used with a descrambling device TI On Off Switch Select On to help eliminate microwave terrestrial interference or OFF for normal use 18V and V H Switch Select the 18V position for single receiver installations Select the V H position when using the UST 524 for multiple receiver installa tions CPU Reset Press this switch to clear the cen
4. channel then press the P LOCK key for more than 4 seconds The P L LED will go out Programming Future Satellites The UST 9000 is designed to identify all the satellites that are currently in orbit In the future there may be new satellites put into orbit The UST 9000 has one letter key and 9 number keys that can be assigned to new satellites You sim ply program the satellite position and assign an identification and number with the or Follow the same programming procedure as you did with the existing satellites Operation Now that the antenna is set up and properly operating and the UST 9000 is programmed with satellite positions and spe cial channels you are ready to pioneer the new frontiers of satellite television With the UST 699 infrared remote in hand and a copy of your favorite satellite program guide try each of the functions listed below All operations described belo a are accessed by the remote control used with the UST 900 or the UST 88 Remote Station a a ee ee Press the Power Key on the Remote The UST 9000 will turn on and all the displays will light The last satellite and channel previously watched will come on You can adjust the volume by pressing the Volume up and down keys or mute the volume by pressing the Mute key Select a Channel Press O 9 keys to select any of 24 channels on the current Satellite The selected channel will appear in the channel dis play and that channel will
5. position are now stored in memory esi ela 2 sme Takia PANOT bis beast E tle tae iin bar BT hati ik EDEN Den Ak Lathe oe gh ee IIE pe ar EMELE re n udio Programming Special A The UST 9000 has been programmed at the factory for all standard audio settings Check your local program guide for audio settings on the satellite which are not 6 8 MHz Mono If any of the channels have audio settings other than 6 8 MHz you will need to program the audio for those channels Find the channels in the guide which have special audio set tings Tune the receiver to the first channel Press the Audio 1 keys to step up or down to the correct frequency If the audio portion of the channel is broadcast in multiplex stereo press the Mode key until the MPX LED lights The Stereo indicator will also light if the audio portion of the channel is broadcast on two audio frequencies press the Audio 2 keys to select the second audio frequency as listed in your program guide If the broadcast is in stereo press the Mode key to select Discrete or Matrix stereo The stereo indicator will light as well as the DSC Dis crete or MTRX Matrix LED Press the DNR key to activate the Dynamic Noise Reduction feature The DNR LED will light Press the NAW key if the program guide calls for narrow band audio Selecting a Satellite and Channel To select a preprogrammed satellite simply press the Type key until the desired satellit
6. to watch Press the Video key under the lid Press the channel keys for the number of the station you wish to call Press the call key The TV screen will display the station number satel lite type and number and the channel Fine Tuning the Video When satellite positions were programmed the best possible picture was tuned There may be times when the signal strays or natural forces cause the alignment of the antenna to change If a certain satellite is consistently bad you may want to reprogram its setting If the signal is temporarily off you can fine tune the picture by momentarily pressing the East or West key If the picture is still not Satisfactory try pressing the Skew keys on the front panel The Video Fine key is primarily used for Ku band reception but may help with some C band satellites There may be other factors that affect the picture quality See the Helpful Hints section of this guide Select an Audio Station The UST 9000 also has a 99 station memory for satellite radio programs You can store your favorite radio channels and access them by calling the station number for that channel The receiver will automatically tune to the satellite channel and audio ready to enjoy Press the Audio key under the lid Press the channel keys for the number of the station you wish to call Press the Call key The TV screen will display the radio station number satellite type and number and the channel NOT
7. Down Limit buttons on the back of the UST 9000 are used to stop the travel of the antenna in both the east and west directions If there is some kind of physical obstruction or other reason that the antenna should not trav el the full distance of its arc the Up or Down limit should be set to stop the travel To set the limit advance the antenna to the farthest position it should travel Press the Down button for a western position or the Up button for an eastern position IMPORTANT BE SURE TO SET BOTH THE UPPER AND LOWER LIMITS AS DESCRIBED ABOVE IF THE LIMITS ARE NOT SET THE ACTUATOR WILL NOT WORK PROPERLY Additional Limit Settings The normai limit of travel for the actuator arm is about 18 inches If the most easterly satellite cannot be reached by the antenna when the actuator arm is fully extended an internal limit switch should be adjusted Remove the back case of the actuator motor housing and locate the red limit switch and cam Loosen the two screws holding cam Turn the cam clockwise until the screw head is located in the center of the slot Tighten screws and replace actuator case Press the Counter Clear switch on back of the unit Press the East key to move the antenna to an eastern satellite Move the antenna about 10 counts beyond the sat ellite and press the Upper Limit switch If the eastern satellite is still out of range repeat the preceding steps and rotate cam further Be sure to reset Upper and Lowe
8. audio channel from 5 8 5 MHz Press once to step 10 KHz press more than 1 2 second to change 80 KHz per sec ond Initial setting is 6 8 MHz for all channels Audio 2 Keys Adjust the frequency of the second audio channel Operation is the same as audio 1 Initial setting is 6 8 MHz for all channels Mode Key Press to change the audio mode from mono to discrete matrix multiplex and back to mono N W Key Press to change the audio band from wide to narrow or narrow to wide Initial setting is wide 13 14 15 16 17 18 19 20 21 22 Station Keys Allows easy selection of your favorite preprogrammed satellite video channels or satellite radio channels After selecting the station number simply press the call key to automatically tune to the preprogrammed satellite and channel P Lock The parental lock allows you to block ir ap tion of a specific channel Select the satellite and chani for which you wish to block reception Press the P Lock key Whenever that satellite and channel are called the video will be blank and the P L LED will light To release the parental lock call the satellite and channel then press the P Lock key for more than 4 seconds Lock Key Press to lock the memory In the lock mode the east and west keys will move the antenna 10 counts for fine tuning only Press the Lock key for more than 4 seconds to unlock the memory Type Key Select the type of sat
9. correspond to your Program guide The video is weak or has superimposed images The polarity indicated in the program guide does not correspond to the setting on the receiver Solution 1 Change the polarity by pressing the V H key G Problem Antenna will not move Antenna movement is erratic Solution 1 Check actuator breaker on back of receiver 2 Actuator improperly installed or binding Check actuator installation and antenna mount to make sure nothing is obstructing movement 3 Check actuator cable for proper connections at both the motor and back of receiver 4 Antenna is too heavy for actuator Check with your Uniden dealer about a heavy duty antenna kit H Problem Remote control will not work works erratically Solution 1 Weak batteries Replace with 2 AA size batteries 2 Remote is not pointed directly at remote window on receiver 3 Remote window on receiver blocked Check and clear any obstructions 4 Out of range Remote will work within 20 feet of receiver as long as there is nothing between it and the receiver The remote will not work through wails furniture or peo ple I Problem Memory programming will not work Solution 1 Memory lock is on Lock LED is on Press the Lock key for more than 4 seconds ee
10. the bi annual solar outage Due to the seasonal changes of the earth s axis the satellite belt moves between the earth and the sun When the satel lite belt moves directly between the sun and your antenna the satellite transmissions will be overpowered by the natural radio transmissions of the sun This kind of satellite eclipse occurs twice a year around the spring and fall equinox As the satellite eclipse approaches you may notice a gradual daily increase in interference It will peak for about 10 30 minutes with a completely distorted picture As the eclipse decreases so will the amount of interference until the picture is back to clear normal operation The degree of interference and th timing of this phenomenon varies with the satellite your geo graphical location and the size of your antenna Unfortunate ly the only solution is to tune to a satellite that is east of the sun s position until it has passed the satellite you were watching Other Sources of Interference All electrical equipment is susceptible to interference from other electrical devices The UST 9000 is an extremly sensitive unit and may pick up interference from any household appli ance If you experience temporary audio or video interference you should check other equipment in your house Appliances such as refrigerators washers dryers microwave ovens pumps power tools hair dryers etc may cause a variety of annoying interference Also radio transmit
11. Check the AC power cord to make sure it is plugged into an outlet that is not controlled by a wail switch 3 Check the main circuit breaker on the back of the unit B Problem The indicator lights are on but no TV picture or audio Solution 1 Check the power switch on the TV or monitor Check the cable between the RF Out connector on the back of the unit and the VHF In on the TV set Make sure both con nections are secured 2 Check the channel selector on the TV to be sure it is set to 3 or 4 and that the 3 4 switch on the back of the unit is set to the same number 3 Check to see if the P L LED is on Parental Lock may be engaged i 4 Check another channe on the satellite The current on may not have any programming Troubleshooting 7 5 Check the cable between the 1 GHz In on the back of the unit and the 1 GHz Out on the Low Noise Block Convert er Make sure the cable is not broken and the connections are secure 6 Check the alignment of the antenna Press the Scan key and look for flashes of color on the screen When video is evident press the Scan key again to stop on that channel Press the East and West key momentarily to align the antenna for the best picture 7 If you still do not have a picture press the Scan key and the East or West to move the antenna to another satellite When video flashes on the screen stop the east or west movement and the channel scan Tune in the satellite as described above
12. E if you call a satellite that has not been programmed the No display will flash and then return to the previous satellite To make sure you get the most out of satellite television viewing we offer the following information The sophisticat ed engineering required to tune in satellite signals from about 22 000 miles away can be as mysterious as space itself We hope that this information will take some of the mystery out of this technology making it even more enjoyable for you External Interference The most common cause of interference for a satellite televi sion system is terrestrial interference It is caused by local telephone or data microwave links If your antenna is located close to or in the path of a microwave tower you may experi ence snowy video sparkles or a distorted picture This kind of interference is usually not constant and may appear to increase and decrease at different times of the day Since telephone traffic is busiest during the daytime you may notice the most interference during daytime viewing You may also notice that this interference occurs only on vertical or hori zontal channels On the back of the UST 9000 is a switch labeled TI ON OFF If you experience terrestrial interference turn the TI filter on If the problem still exists you may need to relocate your antenna or use more sophisticated filters Con tact your Uniden dealer for more information Solar Outage Another cause of interference is
13. come on Press key and in 2 seconds channel 1 will appear Press keys 2 2 and channel 22 will appear Press the channel up or down keys to rapidly step through each channel Select a Satellite Open the lid at the top of the remote Press the Type key until the letter of the satellite you wish to view appears Press the No key until the satellite number appears Press the Call key The antenna will move to the preprogrammed position for that satellite Select the desired channel on that satellite If the satellite you selected is not programmed in memory the Satellite display will revert to the last satellite Select the Audio When a satellite and channel have been called the audio will come on as Audio 1 6 8 MHz Mano This setting is common for most programming If your local satellite program guide indicates a different setting press the Mode key for Discrete or Matrix stereo Press the Narrow key if the guide calls for narrow band audio Tune the Audio 1 frequency to the pre scribed setting Tune the Audio 2 frequency to its setting Select DNR for clearer audio Whenever a channel or satellite is changed the audio will revert to Audio 1 6 8 MHz Mono Select a Video Station The UST 9000 has a 99 station memory for video programs 4 You can store your favorite channels and access them byg Calling the station number for that channel The receiver will automatically tune to the satellite channel and audio ready
14. e letter is displayed Next press the No key until the satellite s number is displayed Check your local program guide to be sure that the correct satellite is displayed Press the Call key The antenna will automatically move to the position for that satellite Once the desired satellite has been located press the channel keys to select a channel The audio portion of that channel will automatically tune to 6 8 MHz Mono and Wide band modes unless special audio frequenci s have been program med Double check the audio information displayed with your pro gram guide to be sure all information is correct Press the Memo key to enter the audio information into memory Whenever this satellite and channel are selected the audg portion will automatically be tuned as programmed Contin ue programming each channel that requires a special audio setting NOTE Most satellite audio programming will be broadcast on 6 8 MHz which has already been preprogrammed into your receiver Your local program guide will keep you updat ed on which satellites and channels currently broadcast ster eo audio and what the correct frequencies are for tuning Continue to the next satellite following the same procedure until ail satellite positions and all special audio settings are stored in memory NOTE The UST 9000 has a memory back up circuit that will keep the memory for about 1 year in the event of a power failure Selecting Audio If you wish to change
15. e number Press and hold to move antenna until key is released Type Key Select the type of satellite Operation is the same as No key Preset Video Key Press to activate the video sta tion mode for easy access to your favorite channels X12 X13 X14 X15 X16 X17 X18 X19 Preset Audio Key Press to activate the audio station function for easy access to your favorite satel lite radio programs DNR Key Press to turn Dynamic Noise Reduction on or off C Ku Band Press to select either C band or Ku band Satellite signals For Ku band reception a Ku band LNB is required Audio 2 Keys Adjust the frequency of the second audio channel Operation is the same as audio 1 Initial setting is 6 8 MHz for all channels Video Fine Primarily for Ku band reception Adjust the first local frequency to fine tune the video Press once to change 156 25 KHz press and hold to rapidly change by 800 KHz second Release to stop Some C band channels may also need to be fine tuned by pressing the or key momentarily No Key Select satellite number Press once to select next number Press for more than 1 2 second to change 4 numbers per second Call Key Press to move antenna to satellite and channel shown in display Battery Compartment Remove cover to replace 2 AA size batteries The above diagram shows a typical layout for the UST 9000 satellite receiver system with ail its options Your
16. ecall the display press the Call button NOTE The superimposed graphics will not appear on chan nels that are not actively broadcasting LS A a ee Memory Lock When all the satellite channel and audio information has been programmed the memory function can be locked to avoid accidental erasure or misprogramming When the memory lock is activated the UST 9000 will not accept any additional programming command except to turn the Paren tal Lock feature on or off The East and West key will move the antenna only 10 counts for fine tuning To lock the mem ory press the Lock key on the front panel The Lock LED will light to confirm that the memory is locked To unlock the memory press the Lock key for more than 4 seconds The Lock LED will turn off Parental Lock The UST 9000 has a special feature which will allow any Sumber of channels on any satellite to be locked out or blocked from viewing If you feel that a certain program is not suitable for viewing you can lock out that channel so that it cannot be seen To activate the Parental Lock cail the satellite and channel that you wish to lock Press the P Lock key on the front panel of the receiver The P L LED will light to con firm that that channel is locked Whenever that channel is called it will appear blank on the TV screen and the P L LED will light You can activate the Parental Lock for a total of 10 channels To turn the Parental Lock off call the satellite and
17. ellite Operation is the same as No key No Key Select satellite number Press once to select next number Press for more than 1 2 second to change 4 numbers per second Release to stop Call Key Press to move antenna to satellite and chan nel shown in display or to tune in a preprogrammed Station number East and West Keys Press once to change antenna position by one number on the display Press and hold to move antenna until key is released DNR Key Press to turn Dynamic Noise Reduction on or off Preset Video Key Press to activate the video staf mode for easy access to your favorite channels Preset Audio Key Press to activate the audio sta tion function for easy access to your favorite satellite radio programs a hat ke Display D1 LED Level Meter Indicates the relative strength of the satellite signal D2 Ku LED Lights when Ku band is selected C band has no indicator D3 DNR LED Lights when DNR function is selected 4 Narrow LED Lights when narrow audio band is ol selected Wide band has no indicator D5 MPX DISC MTRX LEDs Lights when these audio modes are selected D6 Video Indicator Lights when the video station mode is selected D7 Lock LED Lights when the memory lock is on D8 Sat Position Memory Ch Displays the antenna positon or preset station channel selected HNH z z st sm H anm Wirm D9 D10 D11 D12 D13
18. n will flicker from the ideo signal Release the East key and press the Scan key to op the channel scan and any 110 120V AC outlet Use the remote control from the receiver pointed at the front of the UST 88 to control all of the functions of your satellite system The superimposed graphics feature will allow you to see the satellites and chan nels you select on your second TV screen You can also pur chase a second remote control UST 699 to use with the UST 88 If you do not have a UST 88 be sure to ask your Uniden dealer for full details Press the channel Up or Down key to locate an active chan nel If the picture appears distorted or scrambled press the polarity key to change polarity If this improves the picture continue If the picture remains distorted select a new chan nel and try the polarity setting again Press the East or West key momentarily to fine tune the antenna to that satellite Press the Skew keys for addi tional fine tuning When the best picture is achieved compare the active channels and the polarity setting on that satellite with your local program guide to identify the satellite to which you are tuned Press the Type key until the correct letter appears in the display for that satellite Press the No key until the correct number appears in the display Press the Memo key to enter the position for that satellite The satellite number will flash twice to confirm entry The satellite and its
19. nt to assign to that channel 1 99 Write that number down along with the program information Press the Memo key Whenever you call that station number the UST 9000 will automatically tune in the preprogrammed channel you want to watch Programming Audio Station Channels Call the satellite and channe of your favorite satellite radio program Select the frequency as listed in your local program guide All satellite radio broadcasts are on the narrow band Press the N W key and check to make sure the Narrow LED is on When you are sure your selection is correct press the Audio preset key Select the station number you wish to assign 1 99 Write down that information then press the Memo key Whenever you call that audio station number the UST 9000 will automaticaliy tune to the preprogrammed radio broadcast you selected Superimposed Graphics Whenever any key on the remote control is pressed the cur rent station number satellite and channel information is dis played on the lower portion of the TV screen This feature allows you to check all programming details to be sure the correct channel or radio station has been selected It is also helpful when using the UST 88 Remote Station The informa tion will be displayed as station number if any P 00 satel lite type and number F 1 and the channel number 00 CH if Ku band is used the screen will display only KU After 4 seconds the display wil disappear To r
20. r limit switches on rear of unit meson arate IMPORTANT Make sure cam screws are tight before replacing actuator case if actuator limit cam is not secure it will cause permenant damage to your unit UST 88 Connection UST 88 Connection The optional UST 88 allows you to control your UST 9000 from another TV away from the receiver Connect the 2 way video splitter included to the RF output cable on the receiv er Connect your main TV to one output on the splitter and connect your second TV where the UST 88 will be used to the other output Run a cable RG 59 from the Remote Sta tion connector on the rear of the UST 9000 to the input on the rear of the UST 88 Place the UST 88 on top of your second TV and plug the AC adaptor into the rear of the unit Programming Now your UST 9000 system is properly installed and is ready or programming Carefully follow each step to become famil ar with the programming procedures The UST 9000 has een designed with the user in mind therefore once the unit 5 programmed the operation is simple rogramming Satellites and Channels ll programming should be done with the keys behind the loor on the front panel of the UST 9000 Turn on the power sure that Lock LED is off Press the Scan key for more than 2 second to rapidly scan the channels Press and hold the ast key The Antenna will begin moving to the east W hen q first satellite is received the TV scree
21. system may not be exactly the same as this diagram shows ree ee ere 7 NOTE Please refer to the cable chart on the preceding page when selecting cable for your system If you have cable runs longer than those indicated in the chart you should consult your dealer for proper cable type Actuator Connection Remove the rear cover of the actuator motor Inside the cas ing is a terminal strip Connect the appropriate wires to the connections on the strip Be sure to use the cables recom mended in the preceding chart Route the wire through the rubber seal and put the case back on the motor Be sure that the gasket is properly seated for a weather tight seal The actuator should then be connected to the 5 screw terminals on the rear of the UST 9000 Make sure that the proper con nections are made Any improper connection can cause per manent damage to your system Actuator Set Up The actuator inner tube should be retracted as far as possible leaving only the pivot socket exposed The satellite position display on the UST 9000 should read 000 If the display is not at 0 press the Clear Counter button on the back of the receiver Once the counter is at 0 press the East key until the counter displays 010 Press the Lower Limit button on the back of the receiver Move the antenna all the way to the east Press the West key to reverse it about 10 counts Press the Upper Limit button on the back of the unit NOTE The Up and
22. ternal audio equipment VCR or monitor Video Output RCA type connector for an external monitor Y CR or descrambling device 6V Pulse and GND Terminals Connectors for a servo motor type polarization device Voltage automatically turns off 4 seconds after polaris changes Counter Clear Press to erase the limits for antenna travel and to reset the counter to 000 Up and Down Limit Set the east and west limit of travel for the antenna a ee Remote Control Remote Control UST 699 _bPposed Keys X1 Power On Off Turn the receiver on or off with this key X2 0 9 Keys Press to select channel or station number X3 Mute Key Press to mute volume Press again to restore volume X4 Channel Up Down Keys Press once to change channel Press more than 1 2 second to change 8 channels per second Release key to stop X5 Volume Up Down Keys Select the volume by pressing or holding up down keys Hidden Keys lift cover to access keys X6 X7 ule X11 Mo N W Key Press to change the audio band from wide to narrow or narrow to wide Mode Key Press to change the audio mode from mono to discrete matrix and back to mono Audio 1 Keys Adjust the frequency of the first audio channel from 5 8 5 MHZ Press once to step 10 KHz press more than 1 2 second to change 80 KHz per second Initial setting is 6 8 MHz for all channels East and West Keys Press once to change anten na position by on
23. ters such as CBs or shortwave radios may be a source of interference Try plug ging the UST 9000 into another outlet or isolated circuit Check with your Uniden dealer for other ways to control this type of interference Aircraft passing over or near to your antenna may cause some temporary interference as it biocks or reflects the satel lite signal This type of interference is momentary and cannot be filtered Western USA Installation If your UST 9000 is installed west of the Rocky Mountains you will need to reverse the installation of the actuator Install the actuator arm on the left side of the antenna and reverse the and connections on the back of the UST 9000 so that the East and West keys operate properly Troubleshooting o 7 If your UST 9000 is not performing up to your expectations please try the simple steps listed below If you cannot get satisfactory results after following these steps contact your local Uniden dealer or call the Uniden Customer Service Center at 1 317 842 2483 9am 5pm EST NOTE Over 80 of the problems occurring with satellite TV systems are related to cable trouble If you are experienc ing any problem with your system first check all cables and connections carefully If the problem still exists try the follow ing steps A Problem The indicator lights on the receiver are not working No vid eo or audio Solution 1 Check the Power switch to make sure it is on 2
24. the preprogrammed audio setting the UST 9000 makes it easy Follow the instructions in the Pro gramming Special Audio section of this guide If you do not wish to permanently change the audio setting do not press the Memo key after tuning the special audio The next time the satellite and channel are called the audio will return to the preprogrammed setting If you decide to make a perma nent change press the Memo key after selecting the special audio NOTE If you call a satellite that has not been programmed the No display will flash and then return to the previous satellite ee A PORAN The sophisticated UST 9000 takes ail the effort out of satellite TV viewing With the push of a few keys you can select as many of your favorite channels as you wish up to 99 auto matically The UST 9000 does all the work It will move the antenna to the satellite and tune in the channel audio and Programming Favorite Channels any other special settings If you would like to listen to a variety of radio broadcasts simply select the audio mode and with a simple 3 button command you can select your favorite satellite radio programs up to 99 Its that simple YE a EN Programming Video Station Channes Call your favorite satellite channel and au fe previously described Check the display to be sure all selections are cor rect including band mode and frequencies Press the Video preset key Select the station number you wa
25. tral processing unit WARNING WHEN THIS BUT TON IS PRESSED ALL MEMORY WILL BE ERASED 18V F type connector for 18VDC power to the UST 524 for multiple receivers installation When the UST 524 is used the 18V V H switch must be in the V H position Remote Station F type connector for hook up of the UST 88 remote control system which allows oper ation of this receiver from a remote location Motor and Terminals 36 VDC 1 5 amp max output for actuator motor Circuit breaker R11 controls this circuit B SEN and GND Terminals Connect to actu ator sensor R11 R12 R13 R14 R16 R17 R18 R19 R20 R21 R22 Actuator Circuit Breaker Push to reset If brea er trips check the antenna and actuator to make sure they are operating properly Main Circuit Breaker Push to reset AC Power Cord Connect to any 110 120V household AC outlet Do not connect to an outlet con trolled by a wall switch AC Outlet Unswitched power for other equip ment such as a monitor or VCR When the power to the UST 9000 is turned off this outlet remains on RF Out F type connector to wire satellite receiver to the VHF antenna terminal of television CH 3 4 Switch Select either channel 3 or 4 depend ing upon your television set Ant In F type connector for external VHF TV antenna When the power is off signal is connected to RF out R15 Audio 1 and 2 Output RCA type connectors for ex
Download Pdf Manuals
Related Search