Uniden CEZ202 Owner's Manual
Contents
1. If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved Follow instructions for repairing if any e g battery replacement section otherwise do not substitute or repair any parts of the device except as specified in this manual Should you experience trouble with this equipment contact Uniden customer service at 800 297 1023 to arrange repairs All repairs must be done by Uniden or an authorized agent Connection to party line service is subject to state tariffs Contact the state public utility commission public service commission or corporation commission for information This equipment is hearing aid compatible NOTICE According to telephone company reports AC electrical surges typically resulting from lightning strikes are very destructive to telephone equipment connected to AC power sources To minimize damage from these types of surges a surge arrestor is recommended Changes or modifications to this product not expressly approved by Uniden or operation of this product in any way other than as detailed by the owner s manual could void your authority to operate this product2. The Product should include all parts and accessories originally packaged with the Product Include evidence of original purchase and a note describing the defect that has caused you to return it The Product should be shipped freight prepaid by traceable means to warrantor at Uniden America Corporation Service Department 4700 Amon Carter Blvd Fort Worth TX 76155 Slimline Phone User s Guide What s in the box Telephone Handset cord Base A 5 amp If any items are missing wen f or damaged contact soc A our Customer Care Line immediately Never use j damaged products z re Need Help You can get MT Coiled answers 24 7 at our website oS handset cord WWW uniden com You Contact Uniden Phone have a question or problem 800 297 1023 30054 3988 need special assistance due Accessibility Help Line 800 874 9314 to a disability as voice or ITY During regular business hours Central Standard Time Visit our website for detailed business hours Important safety precautions When using your telephone equipment always follow basic safety precautions to reduce the risk of fire electric shock and injury to persons including the following gt Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool gt Avoid using a telephone other than a cordless type during an electrical storm There may be a remote
3. Connecting the Phone Route the cord through the channel Use the telephone cord to connect the line jack to a standard telephone wall jack Use the coiled cord to connect the handset to the base use the jack marked with the handset icon Route the cord through the channel To reduce the risk of fire use only No 26 AWG or larger e g 24 AWG UL listed or CSA Certified Telecommunications Line Cord Test the connection 1 Pick up the handset and listen for a dial tone If you don t hear one check the connection between the base and the phone jack 2 Make a test call If the dial won t stop when you dial check the Tone pulse switch if it s on tone change it to pulse and vice versa Try your test call again If static or noise is on the line see the section on Solving Problems FCC Part 15 Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio o
4. TA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant See installation instructions for details The REN is used to determine the number of devices that may be connected to a telephone line Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to a line as determined by the total RENs contact the telephone provider The REN for this product is part of the product identifier that has the format US 6NYTE BXXXXXX The digits represented by are the REN without a decimal point e g 18 is a REN of 1 8 If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service
5. e REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 One year Limited Warranty Important Evidence of original purchase is required for warranty service WARRANTOR UNIDEN AMERICA CORPORATION Uniden ELEMENTS OF WARRANTY Uniden warrants for one year to the original retail owner this Uniden Product to be free from defects in materials and craftsmanship with only the limitations or exclusions set out below WARRANTY DURATION This warranty to the original user shall terminate and be of no further effect 12 months after the date of original retail sale The warranty is invalid if the Product is A damaged or not maintained as reasonable or necessary B modified altered or used as part of any conversion kits subassemblies or any configurations not sold by Uniden C improperly installed D serviced or repaired by someone other than an authorized Uniden service center for a defect or malfunction covered by this warranty E used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden or F installed or programmed by anyone other than as detailed by the owner s manual for this product STATEMENT OF REMEDY In the even
6. ontact your telephone provider to subscribe to this service If you get a Call Waiting call the handset beeps Press Flash to switch between the current call and the waiting call each time you switch there s a short pause before you re connected to the other caller Changing the Audio Volume During a call press Boost to activate the Volume dial Use the dial to change the volume When you re finished press Boost again to deactivate the Volume dial Wall Mounting the Phone You can mount the phone on any standard telephone wall plate where the pins are 100 mm 3 16 inches apart line cord through 4 Before p the inside channel putting the Biz handset in ilies the cradle you need to ite switch the Cc nants Tuck excess line cord into the Y space on the back of the phone 9 clip into wall mount mode as shown in the drawing Line up the notches on the base with the pins on the wall plate Place the phone over the plate and slide it down to lock it into place below ET the clip from ET to back Slide it back into the slot Rotate the rd 180 rd Slide the clip out of its slot Solving Problems If you have any trouble with your phone try these simple steps first If you still have a question or problem call the Customer Hotline listed on the front page Problem Things tot keep hearing a dialtone Checking the Tone pulse swi
7. r television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help If your home has wired alarm equipment connected to a phone line be sure that installing the system does not disable your alarm equipment If you have questions about what will disable alarm equipment contact your telephone company or a qualified installer Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Industry Canada I C Notice Terminal equipment NOTICE This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications This is confirmed by the registration number The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met It does not imply that Industry Canada approved the equipment NOTICE The Ringer Equivalence Number REN for this terminal equipment is marked on the equipment itself Th
8. risk of electric shock from lightning gt Do not use the telephone to report a gas leak in the vicinity of the leak SAVE THESE INSTRUCTIONS Uniden works to reduce lead content in our PVC coated cords in our products and accessories Warning The cords on this product and or accessories contain lead a chemical known to the State of California to cause birth defects or other reproductive harm Wash hands after handling Uniden is a registered trademark of Uniden America Corporation The pictures in this manual are used for examples only Your actual phone may not look exactly like the pictures Using the Phone Visual ringer light Penden ii Reset Vol button olume dial TE pa 50E J gr gs Mute Flash ot button utton win he N Redial kea Tone pulse button switch Handset A clip Ringer switch Button What it does Boost and These controls work together to change the volume See Volume dial Changing the Audio Volume During a call switch to a waiting call Tone pulse Change the dial mode see Solving Problems During a call Hang up the current call and get a dial tone During a call press amp hold to mute the microphone so callers Mute i l can t hear you Release to turn the microphone back on Redial Redial the last number Turn the audio ringer but not the visual ringer off or on Using Call Waiting Call waiting is service provided by your local telephone provider c
9. t that the product does not conform to this warranty at any time while this warranty is in effect warrantor will either at its option repair or replace the defective unit and return it to you without charge for parts service or any other cost except shipping and handling incurred by warrantor or its representatives in connection with the performance of this warranty Warrantor at its option may replace the unit with a new or refurbished unit THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER WHETHER EXPRESS IMPLIED OR ARISING BY OPERATION OF LAW INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow this exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you LEGAL REMEDIES This warranty gives you specific legal rights and you may also have other rights which vary from state to state This warranty is void outside the United States of America and Canada PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY If after following the instructions in the owner s manual you are certain that the Product is defective pack the Product carefully preferably in its original packaging
10. tch if it s on when try to make a call tone change it to pulse and try again The phone rings but I can t Checking the coiled cord connection hear anything between the base and the handset If there s static on the line z DSL broadband Internet service can DSL filter cause static on telephones but a DSL filter usually solves any problems To get a DSL filter call your DSL provider Telephone i elephone cord or look in any electronics store wall jack To install the filter plug the DSL filter into the wall jack and then plug your J ZB phone into the filter Make atest call lt Z to see if the noise is gone A A What Else Do I Need to Know FCC compliance information Part 68 information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA On the bottom of this equipment is a label that contains among other information a product identifier in the format US 6NYTE BXXXXXX where XXXXXX stands for a specific model number If requested this number must be provided to the telephone company An applicable Universal Service Order Codes USOC certification for the jacks used in this equipment is provided i e RJ11C in the packaging with each piece of approved terminal equipment A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the AC
Download Pdf Manuals
Related Search