U-Line 2175BEVOL2 User's Manual
Contents
1. Overlay Frame 2175BEVOL2 Units Only FRAME PREPARATION IMPORTANT The thickness of the wood overlay panel must be 3 4 Right hand isometric view shown Opposite 2175BEVS 2175BEVOL2 Beverage Center 1 OO SOs SO Use the following instructions to create or have a wood overlay panel created for your Echelon Wine Captain or Beverage Center model as shown in Figure 13 Drill holes for pivot pins upper door hinge and lower door hinge as shown The overlay door panel must be installed in accordance with the Installation Instructions starting on page 9 for left hand 3 8 6 N See Detail A NOTE Final component is only a picture frame No panel inside of rails and stiles NOTE Front view of wood panel with 29 3 4 right hand hinge shown A mirror image t for left hand hinge 2 1 4 CAF Detail A Door top Scale 2 1 3 16 x 11 16 deep Detail C Door bottom Scale 2 1 3 8 x 1 4 deep Chamfer 1 32 x 45 Section A A Scale 2 1 Typ 4 places erie 3 474 ol Dim A 23 3 4 2275WCOL 2175WCOL2 2175BEVOL2 www U LineService com Dim A 14 3 4 2115WCOL2 Figure 13 me See Detail C ULIN_1024_A 03 2008 PREPARE THE NEW OVERLAY PANEL IMPORTANT 2175BEV 2175BEVOL2 Beverage Center The overlay door panel must not weigh more than 20 Ibs The thickness2. 2175BEV 2175BEVOL2 B U LINE OA CIAECS 2BEV 217 3BEVOL2 Beverage Center U Product Dimensions Door Swing Clearances Information Wood Overlay units have a zero clearance for the door to open 90 see Figure 3 Stainless Steel models require a minimum of 2 1 8 door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure 25 3 8 m Including Handle 1 4 Min 2 1 8 Min I 90 90 Door Swing Door Swing WwW Wood Overlay Stainless Steel Figure 3 23 15 16 Eee re Other Site Requirements 23 1 4 Including m Wood The unit requires a grounded and polarized 115 VAC Overlay 60 Hz 15A circuit normal household current See Electrical Specifications on Page 14 Power Supply Environmental Requirements Many U Line models are designed to operate in harsh outdoor marine environments Special considerations include the following e The units are designed to operate between 50 F 10 C and 110 F 40 C High ambient temperatures 110 F 40 C or higher may reduce the unit s ability to reach low temperatures e For best performance keep the unit out of direct sunlight and away from heat generating equipment e In climates where high humidity and dew points are present condensation may appear on outside surfaces This is considered normal The condensation will disappear when the humid
3. Once your unit is installed keep the Use and Care Guide and this Installation Guide in a safe place for future reference 2175BEVS units are Stainless Steel Stainless Steel units are covered with a protective coating and have been ordered left or right hand hinged The Stainless doors are not reversible 2175BEVOL2 units are Black with a door that requires the construction of a 3 4 inch thick wood overlay frame You must determine left or right hand opening before construction All units come with maple trim wine racks that can be finished or stained Please carefully follow the directions that apply to your unit and your intended design Tools Materials Required e Screwdrivers slotted and Phillips head e Sandpaper low odor water clean up quick drying finish tack cloth and if desired water based wood stain and synthetic foam brush e 3 4 inch overlay frame material cutting tools drill and bits 2175BEVOL2 units Inspection Unwrap and inspect the unit on a flat level surface capable of supporting its entire weight Removing Protective Coating Stainless Steel Units Only When inspecting installing a Stainless Steel unit the protective coating covering the unit must be removed first Start at a corner of the unit door and pull back the protective coating to remove it from the unit door www U LineService com U U LINE CORPORATION 2175BEVS 2175BEVOL2 Beverage Center After all the protective coating h
4. a level to check the levelness of the Beverage Center from front to back and from side to side Level www U LineService com 2175BEVS 2175BEVOL2 Beverage Center Ee SO should be placed along top edge and side edge as shown see Figure 25 Figure 25 2 If the Beverage Center is not level adjust the feet on the corners of the unit as necessary see Figure 26 0 N a g Turn Foot to Adjust Figure 26 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level Go on to 8 Install the Unit Installation Tip If the room floor is higher than the floor in the cut out opening adjust the rear feet to achieve a total unit rear height of 1 8 less than the opening s rear height Shorten the unit height in the front by adjusting the front feet This allows the unit to be gently tipped into the opening Readjust the front feet to level the unit after it is correctly positioned in the opening 8 Install the Unit ANTI TIP BRACKET INSTALLATION 1 Locate the two Anti Tip brackets included inside the unit 03 2008 a UFsLINE O E P A CS OT 2175BEV 2175BEVOL2 Beverage Center U p e 2 Place the unit into the area where it will be installed Check the door sides and top for a proper fit Also test the make sure the door opens and closes freely 3 Remove grille and place mark on the floor at the front o
5. door Figure 7 Remove door by tilting forward and lifting off bottom hinge pin ULIN_0003_A Figure 9 4 Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge Figure 10 door closer inserts Figure 10 5 Remove existing bottom hinge 3 screws and remount on opposite side TOP Remove hinge screw pin baled 6 Remove the plastic hole plug from the top of the door to allow the pivot pin to be inserted in the new location Install the plug into the vacated hole on the 2 Remove metal hinge plugs 3 each top and bottom opposite side from new hinge location Do not discard Figure 8 Figure 7 www U LineService com 8 03 2008 CORPORATION E PF P ARA ay ee 2175BEV 2175BEVOL2 Beverage Center D UFLINE 7 With bottom of door facing up remove pivot plate 2 10 Install metal hinge plugs removed in step 2 in old hinge screws flip over and remount on opposite side of door holes 3 each top and bottom Figure 11 Be sure angled side of plate faces center door pivot plate bottom hinge screw pin ULIN_0274_A Figure 11 Figure 12 8 Holding door upright with top of door tilted forward place hole of door pivot plate on bottom hinge screw pin Figure 12 9 Tilt top of door into position in top hinge and install top hinge screw pin 03 2008 9 www U LineService com U U LINE CORPORATION
6. harness on the back 3 Disconnect the wiring harness from the controller Figure 6 3 4 Remove the two screws holding in the controller housing Figure 6 2 then remove from wood Note Carefully remove controller from housing The glass front is not secured to the controller Glass may fall and break which is not covered under warranty 5 After staining installation is the reverse Be sure to align glass with controller when installing otherwise controller may not work correctly 03 2008 2175BEV 2175BEVOL2 Beverage Center U U LINE CORPORATION N WARNING To prevent permanent damage to the inner liner of your unit the wood trim MUST be removed from the unit for staining and or finishing Allow stain finish to dry thoroughly at least 24 hours per coat in accordance with the product manufacturer s instructions prior to reinstallation Failure to do so may cause the inner liner of the unit to have a permanent odor which is not covered by the warranty If staining the trim is desired it must be done before the application of any type of final finish Review the following staining final finish and final finish only guidelines when staining and or sealing the wood to ensure proper adhesion and durability of the finish Note Glass in door is tinted Stain may look darker when door is closed Staining and final finish application 1 Remove all screws securing wood trim to interior components and re
7. the cabinet 1 Grasp the end of the rack and gently slide it out until it stops 2 Remove any bottles stored on the rack Figure 5 3 Press the left rack release lever Figure 5 down and at the same time lift the corresponding right rack release lever up and pull the rack out until it is free of the tracks and the cabinet IMPORTANT Do not remove the track side rails from the cabinet 03 2008 Le Es OO To insert a rack in the cabinet 1 Align the left and right rack channels with the tracks in the cabinet and ensuring an even track engagement on both sides gently push the rack into the cabinet until it stops 2 Before reloading the rack ensure proper operation of the travel stops in the left and right track rails by pulling the rack out gently until it completely stops Wood Trim Finishing The U Line Beverage Center is equipped with wood trimmed wine racks that are coated at the factory with a clear vinyl sealer which will adequately protect the wood in normal usage A final finish coat was not applied so that the wood trim could be stained to match d cor The trim on the racks may be coated with a final finish or stained To remove the wood trim surrounding the controller Figure 6 1 Loosen the two screws holding the controller to the mounting bracket Figure 6 1 2 Lift the controller housing Figure 6 4 and then rotate forward to expose the wiring
8. 1 8 below the top of the unit s cabinet NOT flush with the top see Figure 20 1 Compare the top edge of the door to the top edge of the cabinet 2 If the door edge is 1 8 below and parallel to the top of the cabinet go on to 6 Prepare Power Supply If it is not note whether the side opposite the hinge needs to be moved UP or DOWN and use the following procedure Adjusting Door Alignment 1 Remove top hinge screw pin Phillips screwdriver see Figure 21 Remove door by tilting forward and lifting off bottom hinge pin 2 With door upside down loosen but do not remove the two screws on the door s bottom hinge plate Figure 21 03 2008 Reinstall the closers lining Mount the door install top Slotted Mounting Holes Angled Ed Towards Center of Door OOo Raise lt gt Lower Outside Outside Door Edge Door Edge Figure 22 See Figure 22 If the top far edge of the door needs to move UP move the hinge plate toward the outside of the door and retighten screws If the top far edge of the door needs to move DOWN move the hinge plate toward the inside of the door and retighten screws Mount the door to recheck alignment and repeat Steps 2 and 3 if further adjustment is necessary When top edge of door is parallel to top edge of cabinet remove the door and ensure the two screws are secure Re
9. NCAUTION Caution means that failure to follow this safety statement may result in minor or moderate personal injury property or equipment damage 03 2008 LI Es Oe General Precautions Use this appliance for its intended purpose only and follow these general precautions along with those listed throughout this guide N WARNING SHOCK HAZARD Electrical Grounding Required e Keep the unit unplugged throughout installation except during testing e Never remove the round grounding prong from the plug and never use a two prong grounding adapter e Never use an extension cord to connect power to the unit e Always keep your working area dry NCAUTION e Use care when moving and handling the unit Use gloves to prevent personal injury from sharp edges e Do not lift the unit by the door or door handle e Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille which may cause the unit to malfunction 03 2008 2175BEV 2175BEVOL2 Beverage Center Y UsLINE CORPORATION 2 Inspect and Plan You have received a carton containing your 2175BEVS or 2175BEVOL2 Beverage Center with a package inside containing a Use and Care Guide a Product Registration Card and an Anti Tip Bracket Installation Kit 2175BEVOL2 units are shipped with an additional package of hardware Complete and mail the Product Registration Card or register online at www U LineService com
10. U U INE C oOoORPORATION E ohoin C Toara Installation Guide a R 2175BEVS Beverage Center and 2175BEVOL2 Beverage Center with Overlay www U LineService com Phone 414 354 0300 FAX 414 354 7905 Service amp Parts Tech Lines Phone 800 779 2547 FAX 414 354 5696 OnlineService U Line com 2008 U Line Corporation 03 2008 U U LINE CORPORATION Contents 1 Follow Safety Precautions 4 2 2 Inspect and Plan 0000 eee eee eee ees 3 Exterior Cleaning 00200e eee eeees 4 3 Prepare Site 0 00 c eee 4 Cut Out Dimensions 0 eee eee 4 Product Dimensions 00e eee eee 5 Door Swing Clearances Information 5 Other Site Requirements 5 5 Side By Side Installation Instructions 6 4 Prepare Racks and Door Frame 6 Wine Rack Removal Installation 6 Wood Trim Finishing 20 00000 7 Reversing the Door 2000eee eres 8 Overlay Frame snanu nannaa annn eee 10 Frame Preparation 020000e eee eee 10 Prepare the New Overlay Panel 11 Attaching the Overlay Panel 11 Assembling Door to Cabinet 12 5 Adjust Door 000 ce eee cence eee 13 Checking Door Alignment 13 Adjusting Door Alignment 13 6 Prepare Power Supply 2000 cece eee
11. as been removed from the unit door clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth Do NOT use abrasive cleaning agents Note If cleaning with mild detergent and warm water solution and soft cloth the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product to prevent discoloration Exterior Cleaning As Required Overlay Models e The door grille and cabinet may be cleaned with a mild detergent and warm water solution Do not use solvent based or abrasive cleaners Use a soft sponge and rinse with clean water Wipe with a soft clean towel to prevent water spotting Stainless Steel Models e Stainless steel models can discolor when exposed to chlorine gas pool chemicals salt water or cleaners with bleach e Keep your stainless steel unit looking new by cleaning with a good quality all in one stainless steel cleaner polish on a monthly basis For best results use Claire Stainless Steel Polish and Cleaner which can be purchased from U Line Corporation The part number is 173348 Comparable products are acceptable Frequent cleaning will remove surface contamination that could lead to rust Some installations may require cleaning on a weekly basis Do not clean with steel wool pads Do not use cleaners that are not specifically intended for stainless steel this include
12. correctly Also re check leveling from front to back of the unit and adjust as necessary Make sure that pivot plate is installed correctly 03 2008 9 Start Up for the First Time Initial Start Up The unit is shipped with the control preset No adjustments should be necessary at this time For information about Adjusting the Temperature Control see the Use and Care Guide Start Up Troubleshooting Q Problem Unit does not appear to turn on when plugged in A Z Solution Make sure outlet has power circuit breaker has not tripped Check to see that control is turned on Q Problem Light is on with door closed Z Solution Touch the LIGHT icon on the display panel This will cancel out the light function and just allow the light to turn on and off with the door opening and closing The Beverage Center has an interior light that is illuminated when the door is opened The light can be left on while the door is closed by pressing the LIGHT icon This will turn interior light on for 4 hours then it will turn off IMPORTANT See the Use and Care Guide s Troubleshooting Guide for more solutions Who to Call Service Information If the need for service arises call the U Line Customer Care Center directly 800 779 2547 To ensure accurate assistance please have your Model Number and Serial Number and an explanation of the problem The Model and Serial Number plate is located inside unit at upper rig
13. e 14 Electrical Specifications 000 eae 14 7 Level the Unit occ ccs Meee a eee ee te 14 Leveling Information 000e eee 14 Installation Tip 00 0c eee eee ees 14 8 Install the Unit 0 0 0 eee ee 14 Anti tip Bracket Installation 14 Single Unit Installation 15 Side by Side Installation 004 16 Installation Troubleshooting 16 9 Start Up for the First Time 000000es 16 Initial Start Up 0 0 e eee eee ee 16 Start Up Troubleshooting 16 Who to Call 2 2 croca nera ra nE tee 16 Service Information 0 0e e0e0es 16 www U LineService com 2175BEVS 2175BEVOL2 Beverage Center Ee Ss SO 1 Follow Safety Precautions IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit e This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes Safety Alert Definitions Safety items throughout this guide are labeled with a Danger Warning or Caution based on the risk type DANGER Danger means that failure to follow this safety statement will result in severe personal injury or death N WARNING Warning means that failure to follow this safety statement could result in serious personal injury or death
14. f the unit Also place a mark on the floor in the center of the unit Figure 27 Drill Holes and ount Anti Tip Brackets to Floor Back of Unit of Unit Figure 29 NCAUTION Other hardware is required for floors made of materials other than wood Marks on floor 7 Place the unit back into position making sure the feet Figure 27 engage the Anti Tip brackets properly Check the alignment of the lines made on the floor in step 3 with 4 Remove the unit Using a square extend a centerline the position of the front feet to ensure proper 20 1 4 toward the back wall Figure 28 At the back positioning of the centerline mark a line that measures 11 1 16 to the left and right This line services as the back edge for SINGLE UNIT INSTALLATION the Anti Tip brackets and its furthest points mark the 1 Remove the two screws from the opposite side of the outer edge of each bracket hinge assembly using a Phillips screwdriver Figure Note Instructions are shown for built in installation Use 30 same dimensions for free standing installation Right handed units shown Left handed units are mirrored Back Line Marks Back Front Wall i of Unit Pi ot i nit N A agar AN W A Figure 30 ae ae Marks i J 7 2 Place bracket part 14154 over holes and attach to on Floor 11 1 16 lt 11 1 16 aes A Bae unit with two screws rem
15. ht hand corner If you need to locate a service company you can go online at www U LineService com and search for a service company by zip code www U LineService com For more than four decades U Line has distinguished itself as the leader in built in undercounter ice making refrigeration and wine storage appliances U Line Corporation located in Milwaukee WI is a family operated manufacturer of built in undercounter icemakers Combo icemaker refrigerators Wine Captain wine storage units refrigerators refrigerated drawers and refrigerator freezers 2008 U Line Corporation Publication No 30225E 03 2008 Rev A
16. ity drops 23 15 16 e U Line does not recommend installation of glass front models Wine Captain wine storage models and Beverage Centers as well as the Combo Drawer model Refrigerator Freezer Ice Maker outdoors or in tropical climates where high humidity and dew point are present on a regular basis unless air conditioning typical 72 F 75 RH will be used es Wood Overlay Figure 2 Please note that the unit has adjustable feet that can add one additional inch to height during leveling or to match adjacent cabinets see Figure 26 on Page 14 03 2008 5 www U LineService com U U LINE CORPORATION Side By Side Installation Instructions For a complete refreshment center install your 2175BEVS or 2175BEVOL2 unit beside a U Line Refrigerator Ice Maker or Combo Model see Figure 4 for typical cut out Note that each Side By Side Installation will be different e Cut out width for a side by side installation is the total of the widths listed under Cut Out Dimensions in each unit s Installation Guide For example Placing a 2175 Beverage Center next to a 2115 series unit would require a cut out width of 24 3 16 15 3 16 39 3 8 Placing a 2175 Beverage Center next to a 2175 series unit would require a cut out width of 24 3 16 24 3 16 48 3 8 e No trim kit is required However 1 4 inch space needs to be maintained between the units to ensure unobstructed door swing e U
17. move the door closers from the bottom hinge clean thoroughly and lubricate the mating surfaces with petroleum jelly up the bosses with holes in hinge and hinge plate see Figure 23 hinge pivot pin and go on to 6 Prepare Power Supply Figure 23 www U LineService com UFLINE CORPORATION 6 Prepare Power Supply Electrical Specifications CAUTION Electrical installation must observe all state and local codes This unit requires connection to a grounded three prong polarized receptacle that has been placed by a qualified electrician The unit requires a grounded and polarized 115 VAC 60 Hz 15A power supply normal household current An individual properly grounded branch circuit or circuit breaker is recommended GFCI ground fault circuit interrupter is usually not required for fixed location appliances and is not recommended for your unit because a GFCI could be prone to nuisance tripping However be sure to consult your local codes See Figure 24 for recommended receptacle location Figure 24 A WARNING SHOCK HAZARD Electrical Grounding Required e Never remove the round grounding prong from the plug and never use a two prong grounding adapter e Never use an extension cord to connect power to the unit Go on to 7 Level the Unit 7 Level the Unit Leveling Information Note It is recommended that the unit is level 1 Use
18. move the trim from the cabinet interior IMPORTANT DO NOT use oil based stains on wood trim Vapors from oil based stains will permanently penetrate the liner and will not dissipate over time 2 Apply Minwax Water Based Wood Stain to wood with a synthetic bristle brush or a foam applicator Allow stain to penetrate approximately three minutes Before the stain is dry take a stain dampened rag and remove any excess stain remaining Wipe in the direction of the grain with medium pressure to achieve the desired stain color 3 After two hours repeat step 2 This will even out the color of the wood 4 Allow stain to dry for a minimum of three hours before applying the final finish 5 If desired sand the wood with very fine sandpaper to smooth the surface after the staining process 6 Remove all dust from the wood and apply one coat of Minwax Polycrylic Protective Finish using a synthetic bristle brush to the wood This finish should be applied in a thin coat following the direction of the grain Apply the finish to the back and sides of the wood first and allow it to dry for two hours Apply the finish to the front side of the wood next and allow it to dry for two hours Sand with very fine 220 grit sandpaper Apply two addition coats of the finish in the same manner but do not sand the trim after the final third coat is applied 7 Allow the final coat to dry for 24 hours before reinstalling the trim to the cabine
19. nits must operate from separate properly grounded electrical receptacles placed according to each unit s Electrical Specifications Typical Side By Side Cut Out o 1 4 Space sl Between Appliances Figure 4 www U LineService com 2175BEVS 2175BEVOL2 Beverage Center 4 Prepare Racks and Door Frame The U Line Beverage Center is equipped with wood trimmed wine racks that are coated at the factory with a clear vinyl sealer which will adequately protect the wood in normal usage A final finish coat was not applied so that the wood trim could be stained to match d cor or overlay frame The trim on the racks may be coated with a final finish or stained 2175BEVOL2 Models are designed for and require installation of an Overlay Frame If none of these treatments are to be included in this installation go on to 5 Adjust Door CAUTION To prevent permanent damage to the inner liner of the Beverage Center the wine rack wood trim MUST be removed from the unit for staining and or finishing Allow stain finish to dry thoroughly at least 24 hours per coat in accordance with the stain finish manufacturer s instructions prior to re installing the wood trim inside the cabinet of the Beverage Center Failure to do so may cause the inner liner of the unit to have a permanent odor which is not covered by the warranty Wine Rack Removal Installation To remove a rack from
20. of the door panel must be 3 4 1 Place a towel or other similar soft non marking material out on a flat clean surface Be sure the material is large enough to have the wood panel not touch the hard marking surface 2 Lay the wood panel out with the front side of the wood facing down 3 Cut the foam tape into four pieces two pieces the width of the overlay and two pieces the height of the overlay 4 Remove adhesive protection strip from one piece of the cut foam and align the edge of the foam tape to the inside edge of the overlay as shown adhering the foam tape to the overlay Figure 14 ZA gp _ Inside edge ee Front surface of overlay frame Figure 14 5 Trim each piece of tape immediately after applying it to the overlay Do not allow any overlapping of the foam tape Damage to the overlay can occur if the foam tape is not trimmed correctly Figure 14 6 If required attach any optional cabinet hardware to the wood panel at this time If an optional cabinet handle is installed make sure the mounting screw heads are below countersunk the back surface of the overlay Note After attaching the optional cabinet hardware additional supports may be needed to keep panel flat for next steps ATTACHING THE OVERLAY PANEL 7 Remove the top hinge pivot pin with a Phillips screwdriver and lift door off bottom hinge pin Figure 15 Be careful not to lose the door closer insert sets Save pivot pin for
21. oved in step 1 using a Phillips Centerline 3 5 screwdriver Tighten screws fully Figure 28 3 Recheck the leveling from front to back and side to side Make any necessary adjustments The unit s top surface should be approximately 1 8 below the countertop 5 Place the Anti Tip brackets on the floor against the line drawn for the outer edge Mark spots for the screw holes Figure 29 6 Use a 1 8 drill to make two starter holes and fasten the 4 Secure bracket into adjoining surface Anti Tip brackets to the floor using the screws provided 03 2008 15 www U LineService com 2175BEV 2175BEVOL2 Beverage Center Y U LINE CORPORATION SIDE BY SIDE INSTALLATION 1 Remove screws shown Figure 31 NCAUTION Be sure to remove and discard screw shown Failure to do so may cause damage to the bracket and or unit Remove and discard screw Figure 31 2 Place bracket as shown and re attach screws to unit using a Phillips screwdriver Tighten screws fully 3 Recheck the leveling from front to back and side to side Make any necessary adjustments The unit s top surface should be approximately 1 8 below the countertop INSTALLATION TROUBLESHOOTING Problem The door remains open unless it is pushed closed Solution The hinges should be self closing when the door is open approximately 8 If this is not the case make sure the closers at the bottom of the hinge pin are clean greased and installed
22. racket is covered by any wood chase thru the hole with a 11 32 drill to open hole in door panel DO NOT drill deeper than 1 4 deep ASSEMBLING DOOR TO CABINET 14 Starting at the corners and working toward the center push the door gasket back into place Make sure gasket is fully seated on all four sides and corners 15 Check the closure assembly on the bottom hinge to be sure it is seated correctly in the bosses in the hinge 16 Position door over closer Be sure the door hinge plate holes align with the bosses on the closer Figure 19 Failure to do so will result in the door not sitting in the proper position and door will not align correctly Sometimes it is helpful to open the door 180 to have the closer and pivot plate align correctly Door closers Figure 19 17 Holding the door in the closed position install the pivot post removed in step 7 thru the top hinge into the top pivot plate Tighten securely with a Phillips screwdriver making sure post is seated fully 18 Adjust door as needed for proper closure Refer to the following section for adjustment procedures 03 2008 z UFsLINE O Ai lay ee 2175BEV 2175BEVOL2 Beverage Center D ee 5 Adjust Door Checking Door Alignment The unit s door is aligned at the factory before shipment However its alignment could have been disturbed during shipment or during overlay frame installation IMPORTANT Properly aligned the door should be
23. s glass tile and counter cleaners e If any surface discolors or rusting appears clean it quickly with Bon Ami or Barkeepers Friend Cleanser and a non abrasive cloth Always clean in the direction of the grain Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems e Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred e Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible 3 Prepare Site Your U Line product has been designed for either free standing or built in installation When built in your unit does not require additional air space for top sides or rear However the front grille must NOT be obstructed and clearance is required for electrical connection in the rear Note Unit can NOT be installed behind a closed cabinet door Cut Out Dimensions femm 1 1 2 24 3 16 Figure 1 Follow the cut out drawing in Figure 1 The 24 3 16 width allows 1 4 for ease in installation and removal of the unit 24 is the cabinet depth in most installations The unit is 23 1 4 deep including the wood overlay frame on 2175BEVOL2 models and 23 1 4 deep including the door and not the handle on Stainless Steel models see Figure 2 www U LineService com 03 2008 SK
24. t interior components www U LineService com U LINE A D pe 2175BEVS 2175BEVOL2 Beverage Center O Holari aie Final finish only application 1 Remove all screws securing wood trim to interior components and remove the trim 2 Lightly scruff sand the wood trim with 280 or finer grit sandpaper 3 Remove sanding dust with a clean dry cloth Hinge plugs 4 The factory applied seal is compatible with virtually all finishes A low odor water clean up quick drying finish such as Minwax Polycrylic Protective Finish is recommended Minwax Polycrylic is an ultra fast drying water based finish Apply a thin coat of a clear protective finish following the container label directions Figure 8 5 Lightly sand and reapply if desired 3 Remove top hinge 3 screws reinstall hinge screw pin 6 Allow the final coat to dry for 24 hours before and remount on opposite side BOTTOM Figure 9 reinstalling the trim to the cabinet interior components Reversing the Door All U Line units except Stainless Steel models may be hinge screw left or right hand opening The door opening is easily pin reversed by moving the hinge hardware to the opposite side The top hinge hardware will be used on the bottom of the other side and the bottom hinge hardware will be used on the top of the other side see Figure 7 Y To reverse the door 1 Using a Phllips screwdriver remove top hinge screw pin from
25. use later 03 2008 Y UsLINE CORPORATION Figure 15 8 Carefully lay the door over the wood panel making sure door is orientated correctly top of door with top of wood overlay 9 Pull door gasket out of the groove completely Start in the middle and pull outward moving towards the corners Figure 16 This may take some force but be careful not to cut or rip the gasket Figure 16 10 After gasket has been removed place it on a flat clean surface 11 Secure door to the back of the wood overlay using tape on all four corners Make sure all four edges are aligned Figure 17 www U LineService com U U LINE CORPORATION DOOR FRAME TOP OF OVERLAY BOTTOM OF OVERLAY ULIN_0418_A Figure 17 12 Use the door frame holes as a guide to lightly punch pilot holes for the 6 x 1 pan head screws Figure 18 6 x 1 pan head _ screws 10 total gt Figure 18 13 Attach the door to the overlay using 6 x 1 wood screws IMPORTANT If you decide to drill pilot holes remove the wood overlay from the door and do not use a drill larger than 7 64 and do not drill deeper than 3 8 The door frame and wood overlay must be aligned properly or the door will not operate correctly www U LineService com 12 2175BEVS 2175BEVOL2 Beverage Center Ee es Oe Note After attaching the wood to the door double check the bottom pivot hole location If the hole in the pivot b
Download Pdf Manuals
Related Search