Turbosound Milan Mi0 User's Manual
Contents
1. Does the loudspeaker remain in protect mode Is the input signal level too high Is the mic line switch set incorrectly re the level controls set too high re the connected sources balanced Ground loops re signal cables near or running parallel to mains cables user manual MILAN M10 Action Connect the mains lead Check the mains outlet or switch to another outlet Press the mains switch Turn the control slowly clockwise Verify signal at the source output Un mute muted outputs or mixer channels Check cables and replace Milan does not supply 48v phantom power Use a dynamic microphone or connect to a mixer with phantom power Turn off the mains switch unplug the loudspeaker before reconnecting Refer to qualified service personnel Reduce mixer or preamp level Change mic line setting to correct source Reduce volume controls or use additional loudspeakers Use balanced cables and 3 pole connectors wherever possible Check wiring Lift audio ground on affected device with adapter Move signal cables MILAN Mi0 user manual Page 21 user manual MILAN M10 Product Dimensions Milan Mi0 329 5mm 13 293mm 11 67 d gt _ EE i 521 5mm 20 57 WLAN MILAN Mi0 user manual Page 22 user manual MILAN Mi0 Technical Specifications Dimensions Net weight Frequency range Dispersion Max SPL cont max Construction2. Connectors Controls Indicators Rigging options Milan Mi0 515mmH x 330mmW x 293mmD 20 3 x 13 x 11 5 11 8kg 26lbs 55Hz 20kHz 3dB 90 H x 60 V 6dB points 119dB 125dB Injection moulded polypropylene enclosure self coloured in dark blue Recessed carrying handle Integral dual angle pole mount socket Powder coated galvanised perforated steel mesh grille Mic input female XLR wired pin 2 hot Line input combo jack female XLR wired pin 2 hot Mix out XLR male wired pin 2 hot IEC mains conector with integrated fuseholder Mic gain Line level Mains on off Bass and treble controls Ground lift switch SIG LIMIT LED Power LED green 6 x M10 threaded internal rigging points MILAN Mi0 user manual Page 23 user manual MILAN M10 Spare Parts LS1029 2 LS 1029 2 10 254mm low frequency driver 04A9340 CD 122 HF compression driver 05B9332 RD 122 Replacement HF diaphragm 16F466 AMP ASSEMBLY Replacement amplifier assembly Accessories rcon m e 07B508 1 2 Speaker pole 35mm x 120cm long 07B830 PB 55 Pole mount wall bracket 07B392 EB 10 18 M10 shoulder eyebolt MILAN Mi0 user manual Page 24 user manual MILAN M10 Warranty All products in this manual are warranted by Turbosound Limited to the original end user purchaser against defects in workmanship and materials used in its manufacture for a period of two 2 years for loudspeakers and one 1 year for electro
3. as keyboards acoustic guitars with on board electronics commonly provide only an unbalanced output on a 2 pole jack connector The Milan loudspeaker line input can handle these connections without any rewiring since pin 3 ve of the input is automatically grounded by the jack plug ime tip hot af ring cold sleeve ground EE mO tip hot af ad cold ground 3 pole jack balanced 2 pole Jack unbalanced If an unbalanced source is to be connected to an input channel via the XLR line input connector either 2 pole or 3 pole jack plugs can be used In both cases pin 3 should be connected to pin 1 ground at the XLR as shown here EI tip 1 ground EO 2 sleeve 3 ground orm tip ER es sleeve Some sources such as mp3 players or CD players commonly provide 2 pole unbalanced phono connectors and these can be connected to the Milan line input channel via either the XLR connector or jack connector In either case wire the connectors as follows tip ER around sleeve 3 tip oc otip sleeve O sleeve MILAN Mi0 user manual Page 12 user manual MILAN Mi0 Connecting to the Milan Mi0 O O MAX ON LIMIT MIC GAIN BASS TREBLE LINE LEVEL klm LIFT MIC IN POWER ON 1 Mains Connector and Fuseholder Mains power is connected to the loudspeaker via a combination IEC connector and fuseholder Make sure that the Milan MiO loudspeaker is turned of
4. electrics a keyboard or MP3 player Connect dynamic microphones directly to the Mic input connector and adjust the volume level Connect line sources to the combo jack XLR connector and adjust the volume control Use the MIX OUT function to daisy chain to additional Milan loudspeakers SE oa OOOO DOOD O MIN max MIN MAX O O N max ON LIMIT MIC GAIN BASS i TREBLE LINE LEVEL ON LIMIT MIC GAIN BASS TREBLE LINE LEVEL use Cis CON Zz gt oo fe NERE hl JL NO LA N ar GROUND LIFT MICIN MIX OUT LINE IN GROUND LIFT MIE IN POWER ON is Oo z MA EEN EE OE OE EN N a a EA oe mo mu Uh MILAN Mi0 user manual Page 15 user manual MILAN M10 Stereo P with an external mixer Two Milan loudspeakers form the left and right elements of a stereo PA setup with all signal sources connected to an external mixing console Connect the outputs of the mixer to the Mi0 line inputs using either balanced XLR cables or balanced or unbalanced jack cables Bring up the master faders on the mixer ensuring that the outputs are not clipping and then adjust both loudspeakers level controls to the desired loudness For consistent balance and response set the tone controls to approximately the same positions on both cabinets LEFT RIGHT 0000 0000 MIN MAX MIN MAX MIN MAX MIN MAX oh ion MIC GAIN BASS TREBLE Gu LEVEL on Si MIC GAIN BASS TREBLE Eie LEVEL Ia GR
5. OUND LIFT MIC IN MIX OUT Hard GROUND LIFT MIC IN MIX OUT MILAN Mi0 user manual Page 16 Stereo P with an external mixer and subwoofers In this example sub frequencies are routed to separate subwoofers in order to gain extended frequency response and higher overall sound level Connect the mixer output first to the user manual MILAN Mi0 subwoofers and then loop up to the Milan loudspeakers Connect the outputs of the subwoofers to the MiO line inputs using either balanced XLR cables or balanced or unbalanced jack cables The tone controls on both cabinets should be set to the same positions nominally flat to begin with Ensure that the mixer outputs are not clipping and then adjust both loudspeakers level controls to the desired loudness O O ON LIMIT MIC GAIN BASS TREBLE LINE LEVEL alle GROUND LIFT MICIN MIX OUT POWER ON OOO MIN MAX Rm MIN MAX LINE IN I I I I I I l I I I I I I I I I KR OOOO MIN MAX MIN MAX ON LIMIT MIC GAIN BASS TREBLE LINE LEVEL 7iLin N GROUND LIFT MIC IN MIX OUT POWER Ex DH ON MILAN Mi0 user manual Page 17 user manual MILAN Mio Stereo PA with powered wedge monitors On larger gigs a separate monitor system provides good quality foldback
6. Turbosound CJ Mitel vid USER GUIDE Turbosound Ltd Star Road Partridge Green West Sussex RH13 8RY United Kingdom Tel 44 0 1403 711447 Fax 44 0 1403 710155 web www turbosound com Issue 1 0 Turbosound Ltd user manual MILAN M10 Contents EG Declaration of Conform iy aa ee RE Ee EE EG ee Be DE GE Os ee EG Gee DE 4 Sarev Considerations ss EE a E ee ser 5 IntroduELOR SE ES ee A DR ee Ge ee ee 6 TEKS SE ES ED FEE ee Ge ERG IE N ES ED EL GEL KE Mice 6 Unpacking ie ER Ge EE ee A 6 Bo a 5 Cc ener EE EE EE OE OE RO EE HE 6 Genina Starte ds REDE A EG EG De RE De N Ge GE EE EG Oe GO GE ee 7 Seli Powered Loudspeakers se N be ER Ee Ge a sas tins Se ed ee GO 9 Using Milan Mi0 with SUD WO Of OMS st DS GR N n Ge ES Ge ee ee died 9 Using Milan MiQ as a Floor Monitor Se GR Ge SG ie 9 Model lniarmatiOn see ED EE Ge EG ee DE A GE GE 10 Milan Mid Self Powered LoudSpe akel cscsscccscsescssssssescsessssssesesescsesesesececsesesesesacsesesesesaacaesesesnsesetaneeses 10 Milan NiO Fedt Sc eet ss esc accu us clatter adele selec ou etc due ca i pst asics ee ee ee es 11 COMME CLOT Wing so ee tect ea sealed Ee ie doc SEERE DERES EE Ee Ge DE SEES 12 Connecting to the Milan VID adi its ee Gn EE RR EG GR Sua tal see ese 13 Mans COnne ctor and Euseholder so Ee ee ee GER ed GE A 13 MES WED SE alee tag RE EO deta aa EG ee We E oe NE Nien eae 13 SR Ege Toro MIL SWEIS N N EG N ED Ee Ee ee PE 13 A Microphone DUE en Se ed GE aG 13 S Line
7. Using Milan Mi0 with Subwoofers Improved bass response and higher overall sound pressure level can be achieved by adding sub bass loudspeakers to the Milan system This also reduces mechanical stress on the Milan loudspeaker s low frequency driver since most of the low frequency content in the signal is routed to the subwoofer It is recommended that you connect the full range signal from the mixer first to the subwoofer s and from there to the Milan MiO Using Milan Mi0 as a Floor Monitor Reduce the level of the BASS CONTROL when using Milan as a floor monitor which will avoid any low frequency boominess due to the proximity of the floor that can detract from clear and intelligible monitor sound If you are using Milan as part of a larger multi channel monitor system and where drums may be part of the monitor mix it is recommended that kick drum EQ is used sparingly and carefully MILAN Mi0 user manual Page 9 user manual MILAN M10 Model Information Milan Mi0 Self Powered Loudspeaker The Milan MiO is a self powered sound reinforcement loudspeaker designed for many different portable and permanently installed applications It consists of a custom 10 low frequency driver matched with a 1 high frequency compression driver on a 90 horizontal x 60 vertical Converging Elliptical Waveguide providing smooth and even coverage over a wide audience area together with a two channel amplifier module providing micr
8. ates that the input signal is too high or additional speakers are required MILAN Mi0 user manual Page 7 user manual MILAN M10 8 When shutting down the Milan system first turn down the input level controls then switch off the mains power before turning off the mixer or signal source MILAN Mi0 user manual Page 8 user manual MILAN M10 Self Powered Loudspeakers The Milan MiO self powered loudspeaker is equipped with an integrated two channel amplifier module driving the high frequency and low frequency components independently taking consistent performance convenience and ease of use to a new level Milan eliminates the need for separate amplifier racks and controllers as well as the attendant cabling This makes setting up at gigs and obtaining a consistent sound in different venues a faster and simpler process The amplifiers are exactly matched to the known parameters of the loudspeaker components and are therefore able to produce the optimum power for the drivers By placing the amplifiers in the cabinet it is possible to keep the loudspeaker cables extremely short to eliminate resistive losses so effectively all the power from the amplifiers is transferred to the drivers The on board electronics provides a mic and line input with two band EQ Fast acting limiters allow you to achieve higher average sound pressure level reduce the possibility of driver damage and help to ensure better long term system reliability
9. eyebolts into the S threaded rigging points and tighten The front rigging points should take the majority of the load I while the rear rigging point should be used for i angling the cabinet downwards only Ke When installing the E S cabinet sideways pick N Q up from either of the two front eyebolt a ig YH j f pairs and bridle the two rear eyebolt points to provide a single pull back for adjusting the downward angle Wall Mounting The Milan loudspeaker can be conveniently wall mounted using the PB 55 pole mount wall bracket which simply locates into the pole mount socket in the bottom of the cabinet Mount the bracket to the wall using suitable fixings and locate the loudspeaker onto the pole mount bracket Rotate and angle the loudspeaker to optimise coverage and tighten the locking mechanism to stop the loudspeaker from being inadvertently removed MILAN Mi0 user manual Page 20 Troubleshooting Fault No power to the loudspeaker No sound quiet sound No sound from connected microphone No sound although loudspeaker is on Distorted sound Distorted sound limit LED is on continuously Hum or noise Check Is the mains lead plugged in Is the Mains outlet live Is the power switch on re the level controls turned down anti clockwise Is the source sending a signal Is the microphone a condenser type needing phantom power Is the loudspeaker in protect mode
10. f before connecting mains power Replace the fuse only with the same type and rating 2 Mains Switch Rocker switch turns mains power on to the loudspeaker Make sure the Mic Gain and Line Level controls are fully off MIN and power up other external equipment such as a mixer before switching on 3 Ground Lift switch Safely lifts the signal ground of the balanced audio inputs from the ground of the amplifier Select position as appropriate in order to minimise hum 4 Microphone Input Balanced female XLR connector for use with a variety of balanced and unbalanced dynamic microphones The mic input is not suitable for condenser microphones that require phantom power The input is balanced to avoid hum loops and RF interference and is wired pin 2 hot pin 3 cold MILAN Mi0 user manual Page 13 user manual MILAN M10 5 Line Level Input Combination jack XLR connector that will accept a wide range of balanced and unbalanced line level sources such as keyboards acoustic guitars with on board electronics and other line level sources such as CD players and DJ mixers 6 Mix Out An unbalanced line level output on a male XLR that connects to additional powered Milan loudspeakers This output contains a mix of all connected sources and is post EO Note that adjusting the equalisation will similarly affect any additional Milan loudspeakers connected from this output 7 Line Level Control Rotary level control which attenuates t
11. for individual performers and helps to keep the PA sound less cluttered LEFT RIGHT OOo OOoo MIN MAX MIN MAX MIN MAX MIN MAX a mar MIC GAIN BASS TREBLE Fe LEVEL Si iar MIC GAIN BASS TREBLE Goa LEVEL SF GROUND LIFT MICIN ae LIFT MICIN MIX C OUT POWER EX ON sopir rs Las hf Oooo OOO MIN MAX MIN MAX MIN MAX MIN T MAX a ing MIC GAIN BASS TREBLE goer T ve MIC GAIN BASS TREBLE Ee LEVEL alle sia S ii 7 ed WAS LIFT MICIN MIX O OUT LINE IN ere LIFT MIC IN MIXO OUT LINE IN MON 1 MON 2 MILAN Mi0 user manual Page 18 user manual MILAN M10 Loudspeaker Placement In order to avoid the possibility of feedback locate the loudspeakers in front of your microphones and do not point microphones directly at the front of a loudspeaker When using speaker stands try to raise the loudspeakers as high as practically possible at least higher than the heads of the audience since people are very good absorbers of sound especially at high frequencies You also have the option to point them down using the alternate angle provided for by the built in dual angle pole holder Doing this will improve the coverage for both near and far audience members SAFETY PRECAUTIONS make sure that any speaker stands you use are capable of taking the weight of the loudspeaker and that stands are placed on a flat level and stable surface Make sure that the legs do not
12. he input signal level of the connected instrument line source 8 Treble Control and 9 Bass control The bass control provides 6dB of boost or cut at 90H with a shelving curve shape and the treble control provides 6dB of boost or cut at 8kHz with a shelving curve shape Always use equalisation sparingly aiming to cut rather than boost especially when the loudspeaker is used near boundaries such as walls or floors 10 Mic Gain Control Rotary level control which attenuates the input signal level of the connected microphone Allows the mic signal to be optimised for the first and subsequent loudspeakers connected to the MIX OUT connector 11 Limit Indicator llluminates green to indicate the presence of signal at the amplifier input llluminates red when the amplifier s output is limited Frequent and or continuous lighting of the limit LED indicates overdriving If this occurs reduce the input level to the loudspeaker or enlarge your system with additional loudspeakers 12 Power Indicator lIluminates green to indicate that mains power is connected and powered up MILAN Mi0 user manual Page 14 user manual MILAN Mi0 Connection Diagrams Small duo setup using the integrated mixer and Mix Out The built in two channel mixer allows the simultaneous use of a low impedance dynamic microphone and a line level source The line level source could be an acoustic instrument such as a guitar with either passive or active on board
13. ilan MiO loudspeaker IEC mains cable User Guide Turbosound logo sticker MILAN Mi0 user manual Page 6 user manual MILAN Mi0 Getting Started OTurbosound SROJF ACONPANY io OM O O MIN MAX ON LIMIT MIC GAIN BASS TREBLE LINE LEVEL A zia GROUND LIFT POWER 1 Turn the Mic Gain and Line Level controls fully anticlockwise MIN 2 Set the Bass and Treble tone controls to their centre position no boost or cut 3 Connect your signal sources mixing console keyboard microphone acoustic guitar to the appropriate input connector 4 Switch on the mixer or other source and make sure the output faders or master output level controls are turned fully down 5 Ensure that the mains voltage requirement of you model as indicated by the voltage label 230v or 120v matches your local AC mains supply Connect the AC mains cable to the Milan loudspeaker and turn on the mains switch The green POWER LED will illuminate to indicate that mains power is connected 6 Increase the output level of the signal source to a normal operating level 7 Slowly turn up the Milan loudspeaker s level control s until a suitable volume level is reached The SIG LIMIT LED illuminates green to indicate signal present and flashes red when limiting It is normal for the SIG LIMIT LED to flash occasionally but excessive or prolonged illumination indic
14. instructions e Heed all warnings e Follow all instructions e Do not use this product near water e Do not install near any heat sources such as radiators stoves boilers or other apparatus that produces heat e Do not allow the mains cable to become damaged twisted cut or caught under other equipment e Do not use the loudspeaker with AC mains supplies lower than 100v or higher than 240v as damage may result e Use only accessories and attachments approved by the manufacturer If the product is to be permanently installed use only rigging hardware approved by Turbosound e Unplug the loudspeaker during lightning storms or when it is not to be used for long periods of time e This equipment must be grounded earthed e Be careful when lifting the loudspeaker for instance when placing onto speaker stands or poles Make sure that you are lifting within your personal capability e Keep the exterior of the loudspeaker enclosure clean and clean only with a dry cloth e Do not install the loudspeaker in outdoor environments where the product could be subjected to moisture excessive temperatures or prolonged UV light exposure Electrically powered devices such as this product can present dangerous shock hazards when wet or exposed to moisture e This product is not suitable for fixed installation in outdoor environments MILAN Mi0 user manual Page 5 user manual MILAN M10 Introduction Congratulations you have pu
15. ite at www turbosound com distrib distribs php Product Information You can find full details on all our products on the internet at www turbosound com products MILAN Mi0 user manual Page 26
16. level DEL es EG DEE ED GE GE Ge GR 14 o NIBE cca Seca sets saa cee laa teas E a O e DE 14 To Line level OROS EG GE GE GO DR Ge Ge dC 14 6 Treble toiitrolard 9 Basseontrel ie Ge Ee ee 14 OSMI Gal Geni Ol Ms Ee GE EG 14 ENE MING C SO SS ee EE Ge SR De GE A 14 12 Power ndie GEO se SE EE EG Ge Ge Ge ee 14 Connection Diagrams EE ES SR N RD n Ge Ge ee aad Ge 15 Small duo setup using the integrated mixer and MIX Out ees se se ee ee ee ee ee RR ee Ge RR ee Ge Ge ee ee ee ee 15 stereo PA with ame kierie ES Gie EG ER EG De De ee ees 16 Stereo PA with an external mixer and subWOOTEFS ees sesse se ee ee ee Ge Ge ee ee ee ee ee ee AR ee ee ER Re ee be ee ee ee ee ee 17 Stereo PA with powered wedge MONIOFS e ee ese ee ee ee ee ee ee Ge Ge Ee ee AR ee ee Ge Re ee GR Re ee Ge Ge Ee ee ek ELLE ee ee ee ee 18 Loudspeaker lA COIN OI se ee De EG ER De GE E be Ee 19 Installing the Milan loudspeaker iese esse se ee RR Ee AR RA Re Ek AA ee Re Ge ee ee ee ee ee 20 Using the MIO Hd POMS se EE GE NE EE ee WE EE DSE 20 MAMI MO ER ER Gode Se Ee ae ee ee ee 20 TM MOUND SUMO OCIA EE EE EE EE EE au a GE WE DE Ee ech ges ee Ee GE 21 Produet Dimension se De EG GO DR Ee ee N SE 22 WA ELE Le Ee ED EE ER REE IE N OE ERE OEER SSPE NE NFDES 22 Technical Speeili aHONSE EDS RE Ge EG EG GE EE OGE ede 23 S parte US si AE OE RE a De ee oe EE ED Ee De Ee 24 ACCES SSOrOS ER A EG er aaa 24 MILAN Mi0 user manual Page 2 user manual MILAN Mi0 WY IAIN CY cus
17. na SES EDER RIR NEUE SEERNES Ee be ee REESE Ee ee ie 25 Contact MiGriatI RRS EE EG eee Ce reece eee 26 CUStOMEr SETVE EE AE RD E 26 fmd more NNE Ia COIN At ON se EE RE EE EE ee N ED SKER SERENE ED ESS GR N SEE OE ED 26 KN KE SK ies EE RE BE Ee Re Ge Ee Error Bookmark not defined MILAN Mi0 user manual Page 3 user manual MILAN M10 EC Declaration of Conformity Manufacturer Turbosound Ltd Star Road Partridge Green West Sussex RH13 8RY UK tel 44 0 1403 711447 fax 44 0 1403 710155 www turbosound com Standards This product complies with directive 89 336 EEC EMC and following modifications 92 31 EEC and 93 68 EEC as stated in EN 55103 1 and EN 55103 2 and with directive 73 23 EEC LVD and following modifications 93 68 EEC as stated in EN 60065 standard Under the EM disturbance the ratio of signal noise will be changed above 10dB FCC Compliance This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 the device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limit
18. ng of Milan loudspeakers and simple expansion of your sound system e Trapezoidal shape with symmetrical 43 wedge angle allows the loudspeaker to be used as a floor monitor e Ergonomically placed handle for easy lifting and carrying e Professional quality 1 high frequency compression driver with wide dispersion Converging Elliptical Waveguide e Custom developed 10 LF driver provides high performance and contributes to lower weight e Dual angle pole mount socket allows the loudspeaker to be used vertically or angled downwards for improved coverage e Durable stylish and lightweight moulded composite enclosure e Internal M10 rigging points on top and bottom for easy suspension in permanent installs e Attractive powder coated and galvanised perforated steel grille MILAN Mi0 user manual Page 11 user manual MILAN Mio Connector wiring The amplifier microphone and line inputs are designed to accept balanced three conductor connections and it is recommended that this method be used since it offers the best rejection of noise hum and radio interference especially where long cable runs are involved XLR connectors should be wired pin 2 hot positive pin 3 cold negative and pin 1 ground while the standard wiring for 3 pole jack plug connectors is tip hot positive ring cold negative and sleeve ground as shown below hot cold ground Balanced male XLR Balanced female XLR Some signal sources such
19. nics from the date of shipment to the end user Faults arising from misuse unauthorised modifications or accidents are not covered by this warranty No other warranty is expressed or implied This warranty does not affect any statutory rights of the purchaser Should any fault develop with a component of your Turbosound system the faulty unit should be sent in its original packaging to the supplier or your local authorised Turbosound dealer with the shipping prepaid You should include a written statement listing the faults found and the product serial number must be quoted ion all correspondence relating to the claim IMPORTANT We recommend you record your purchase information here for future reference Dealers Names EE N EER se ee EG Se GE MG ee ek Ge ee Ge Ee GE eg ee PRO CEOS SS AE ORE EE GE SE N DE DE EG aude view GE N EE N DE eee OE N ee N AE PEDONE NO vs AE EE Oe Ee Ee A De EE de Invoice Recept NOW Date cet BR ee ER oe EG ee A Serra PU CS Me N ee S AE EE RE EE EE a a tae N Jil In keeping with our policy of continual improvement Turbosound Limited reserves the right to alter specifications without prior notice MILAN Mi0 user manual Page 25 user manual MILAN M10 Contact Information Turbosound Ltd Star Road Partridge Green West Sussex RH13 8RY United Kingdom Customer Service If your product requires servicing please contact your local distributor or retailer A complete list is available on our webs
20. ophone and line level input channels and Ee equalisation These high quality professional components are housed in a lightweight stylish and durable trapezoidal moulded polypropylene cabinet that is instantly adaptable to front of house or floor monitoring applications The cabinet is extensively ribbed and internally damped This design feature increases the cabinet s rigidity and eliminates internal reflections which translates into better transient response and improved bass reproduction It also keeps the weight of the cabinet as low as possible ss EA ATT NM MiO is equipped with a dual angle pole mount socket which allows it to be angled down for better coverage when used with tripod stands or for mounting on top of bass cabinets Lifting and carrying is made easy with the provision of a comfortable scoop handle on the top of the cabinet The MiO cabinet provides M10 rigging points on the top and bottom for suspending horizontally or vertically in permanent installs MILAN Mi0 user manual Page 10 user manual MILAN M10 Milan Mi0 Features e Two discrete amplifier channels 360 watts program Class D low frequency and 100 watts program Class AB high frequency for excellent audio quality e Integrated mixer provides XLR microphone input and line input on combination jack XLR connector e Two band EO with 6dB of cut and boost e Mix Out function allows daisy chaini
21. present a trip hazard Take care when lifting the speakers on to the stand ask someone else to help you if needed TUW W N TU i The same applies to using Milan loudspeakers mounted on straight poles on top of bass cabinets or subwoofers Adjustable height poles or stands allow you to fine tune the height of the loudspeakers to suit your venue Do not place your loudspeakers too close to turntables as this may induce rumble or low frequency feedback from the tone arms Isolate turntables on shock mounts Use equalisation sparingly Start with the bass and treble controls at their neutral position no boost or cut Cut a little bass to tame any boomy frequencies in the room and add a little treble to help vocal intelligibility Consider adding subwoofers and or further loudspeakers if the overall sound level or low freguency response is not enough for the room MILAN Mi0 user manual Page 19 user manual MILAN M10 Installing the Milan loudspeaker Using the M10 rigging points The Milan loudspeaker can be permanently installed in a venue suspended from eyebolts fitted to the internal M10 rigging points on the top and bottom of the cabinet Three possible orientations are available vertically upright or upside down to position the high frequency driver closer to the audience or sideways if required Insert M10 load rated shoulder
22. rchased a professional loudspeaker product from the Milan series of loudspeakers designed to give you the best in audio quality and many years of reliable trouble free operation It offers excellent pattern control safe and practical rigging hardware superior audio quality proven reliability ease of setup consistent performance and the backing of a world leader in acoustics technology including a comprehensive warranty against manufacturing defects Please read through this manual carefully before you attempt to operate the loudspeaker system It contains valuable information which will enable you to quickly and easily connect the loudspeakers to your outboard equipment and important system and set up checks Thanks Thank you for choosing a TURBOSOUND loudspeaker product for your application By engaging in an on going rigorous program of research and development all TURBOSOUND products are carefully engineered for world class performance and reliability If you would like further information about this or any other TURBOSOUND product please contact us Detailed product information is available on our website at www turbosound com We look forward to helping you in the near future Unpacking After unpacking the unit please check carefully for damage If damage is found please notify the carrier concerned at once You the consignee Must instigate any claim Please retain all packaging in case of future re shipment Contents M
23. s are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Category Professional apparatus for use in Commercial Light Industrial and controlled EMC environments CE Marking All products are marked in accordance with the relevant statutory requirements Simon Blackwood Managing Director Dominic Harter Sales Director July 2011 MILAN Mi0 user manual Page 4 user manual MILAN M10 Safety considerations Before using your Milan loudspeaker please read the following information as it pertains to your safety and the reliability of your product e Read and retain these
Download Pdf Manuals
Related Search