Troy-Bilt 24C-060F063 User's Manual
Contents
1. Handle The starter handle is attached to the right upper handle Stand behind unit and pull the starter handle to start engine Bag Collects shredded material fed through the chipper chute or vacuumed through the nozzle or hose Bag Handle Used to grasp bag in order to assist in attaching removing and emptying bag Chipper Chute Allow twigs and small branches up to 1 1 to be fed into the impeller for chipping Blower Chute If Equipped When attached to unit the blower chute is used to blow or scatter yard waste such as leaves pine needles or small twigs across yard Nozzle Height Adjustment Lever Used to adjust the nozzle ground clearance ranging approximately 5 8 to 4 1 8 Nozzle Yard waste such as leaves or pine needles can be vacuumed up through the nozzle for shredding in diameter Hose Assembly Used as an alternative to the nozzle to vacuum yard waste such as leaves or pine needles in hard to reach places Hose Handle Used to guide hose assembly when vacuuming Nozzle Hose Vac Handle The nozzle hose vac handle is located on top of the nozzle and it is used to regulate the vacuum between the nozzle and the hose assembly Throttle Control Lever Not Shown The throttle control lever is located on the engine It controls the engine s speed and stops the engine See separate engine manual packed with unit for details Engine Controls See the separate engine manual for the location and funct2. blower chute if equipped from the unit as instructed in the OPERATION section to obtain access to flail screen See Figure 11 Hex Screw amp Flat Washer Lock Nut Flail Screen Figure 11 e Remove hex screw on right side of unit that attaches to the fail screen It may be necessary to remove the hose bracket hanger to get access to the hex screw See Figure 12 Remove hex screw and flat washer on top of rear housing mounting bracket and the lock nut that secures flail screen See Figure 11 Remove and clean the screen by scraping or washing with water Reinstall the flail screen Remove Hex Screw Sharpening Or Replacing Chipper Blade Because the engine on this unit has a tapered crankshaft a special impeller tool part number 753 0900 is required to remove the impeller assembly For further assistance contact your local service dealer NOTE When tipping the unit empty the fuel tank and keep spark plug side up e Disconnect the spark plug wire and ground it away from the spark plug Remove the front hubcaps lock nuts front wheels and wave washers that attach to the pivot arm assemblies See Figure 13 Remove the shoulder screws thrust and bell washers that go through the pivot arms and height Pivot Arm Assembly Bell Washer Wave Washer Height Adjustment Bracket Thrust Washer Figure 13 e Remove the three screws on the upper housing that secure the nozzle cover and the
3. clean dry area Do not store next to corrosive materials such as fertilizer SECTION 6 TROUBLESHOOTING Problem Cause Remedy Engine fails to start Spark plug wire disconnected pes Connect wire to spark plug 2 Fueltank empty or stale fuel 2 Fill tank with clean fresh gasoline 3 Throttle control lever notin correct 3 Move throttle lever to FAST position starting position 4 Choke notin CHOKE position If 4 Move choke to CHOKE position Equipped 5 Engine if equipped with a primer 5 Prime engine not primed properly 6 Blocked fuel line 6 Clean fuel line 7 Faulty spark plug 7 Clean adjust gap or replace Engine runs erratic 1 Spark plug wire loose 1 Connect and tighten spark plug wire 2 Unit running on CHOKE If 2 Move choke lever to OFF position Equipped 3 Blocked fuel line or stale fuel 3 Clean fuel line fill tank with clean fresh gasoline 4 Water or dirt in fuel system 4 Drain fuel tank Refill with fresh fuel 5 Dirty air cleaner 5 Clean or replace air cleaner 6 Carburetor out of adjustment 6 See authorized service dealer Too much vibration 1 Loose parts or damaged impeller 1 See authorized service dealer Engine overheats 1 Engine oil level low 1 Fill crankcase with proper oil 2 Dirty air cleaner 2 Clean or replace air cleaner 3 Carburetor not adjusted properly 3 See authorized service dealer Occasional skip hesitates 1 Spark
4. the engine PREPARATION 1 Thoroughly inspect the area where the equipment is to be used Remove all rocks bottles cans or other foreign objects which could be picked up or thrown and cause personal injury or damage to the machine Always wear safety glasses or safety goggles during operation or while performing an adjustment or repair to protect eyes Thrown objects which ricochet can cause serious injury to the eyes Wear sturdy rough soled work shoes and close fitting slacks and shirts Loose fitting clothes or jewelry can be caught in movable parts Never operate this machine in bare feet or sandals Wear leather work gloves when feeding material in the chipper chute Before starting check all bolts and screws for proper tightness to be sure the machine is in safe working condition Also visually inspect machine for any damage at frequent intervals Maintain or replace safety and instructions labels as necessary To avoid personal injury or property damage use extreme care in handling gasoline Gasoline is extremely flammable and the vapors are explosive Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite Wash your skin and change clothes immediately a Use only an approved gasoline container b Extinguish all cigarettes cigars pipes and other sources of ignition c Never fuel machine indoors d Never remove gas cap or add fuel while the engine is hot o
5. through nozzle See Figure 8 e The spring loaded pin must be in the first hole of the hose adapter to operate the nozzle vac e Place both hands on top of upper handle to push unit over yard waste Yard waste such as leaves and pine needles can be vacuumed up through the nozzle for shredding After material has been shredded by the flail blades on the impeller assembly it will be discharged into catcher bag or through blower chute if equipped Do not attempt to shred or chip any material other than vegetation found in anormal yard i e branches leaves twigs etc Avoid fibrous plants such as tomato vines until they are thoroughly dried out Materials such as stalks or heavy branches up to 1 1 2 in diameter may be fed into the chipper chute Nozzle Hose Vac Handle Top Position Spring Loaded Pin First Hole Figure 8 IMPORTANT The flail screen is located inside the housing in the discharge area If the flail screen becomes clogged remove and clean as instructed in SECTION 5 MAINTAINING YOUR YARD VACUUM For best performance it is also important to keep the chipper blade sharp WARNING Do not at any time make any A adjustments without first stopping engine and disconnecting spark plug wire Using the Hose Assembly e Place nozzle hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assembly See Figure 9 The spring loaded pin must be in the second hole of the hose a
6. 6 Nozzle height adjustment levers Lubricate the pivot points of the nozzle height adjustment levers once a season with light oil Refer to Figure 6 Locking Rod Lubricate the locking rod with light oil to ease the application of attaching on or removing bag or blower chute if equipped Refer to Figure 6 Nozzle Hose Vac Handle Lubricate the nozzle hose vac handle on top of nozzle once a season with light oil Refer to Figure 6 Engine Follow the separate engine manual packed with you unit for lubrication instructions Maintenance Engine Refer to the separate engine manual for all engine maintenance instructions e Check engine oil level before each use as instructed in the separate engine manual packed with your unit Read and follow instructions carefully e Clean air cleaner every 25 hours under normal conditions or once a season Clean every few hours under extremely dusty conditions To service the air cleaner refer to the separate engine manual packed with your unit The spark plug should be cleaned and the gap reset once a season Check engine manual for correct plug type and gap specifications Removing The Flail Screen If the discharge area becomes clogged remove the flail screen and clean area as follows e Stop the engine and make certain the Yard Vacuum has come to a complete stop e Disconnect spark plug wire from spark plug and ground against the engine e Remove the bag or
7. OTROY BILT Operator s Manual Yard Vacuum Chipper Shredder Vacuum Hose Model Numbers 24B 060F063 24C 060F063 IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest covered brush covered or grass covered land unless the engine s exhaust system is equipped with a spark arrester meeting applicable local or state laws if any If a spark arrester is used it should be maintained in effective working order by the operator In the State of California the above is required by law Section 4442 of the California Public Resources Code Other states may have similar laws Federal laws apply on federal lands A spark arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department P O Box 361131 Cleveland Ohio 44136 0019 TROY BILT LLC P O BOX 361131 CLEVELAND OHIO 44136 0019 PRINTED IN U S A FORM NO 769 00835 8 03 TABLE OF CONTENTS Content Page Important Safe Operation PractiCeS ecccceescceceeeeeeeeeeseeeeeeeaeeeeeneeessaeesennees 3 Assembling Your Yard Vacuum c ccccecceceeeeeeeceeeeeeeeeneeeeeeeeeeeeeeeeeeneaeeeeeneneaeees 5 Know Your Yard Yacu sssskseciocren aea 7 Operating Your Yard VACUUM 0 cccececeeeceeeeeeeeeeeeseaaeeeceeeesaaeeeeaaeesesaeeseeaeeeeaes 8 Maintaining Your Yard Vacuum 0 eeeecceeeeeescneeeee
8. age If the fuel tank has to be drained do this outdoors Observe proper disposal laws and regulations for gas oil etc to protect the environment A NOTE Not all safety labels may apply to your Yard Vacuum 4 DANGER TO AVOID SERIOUS INJURY READ OPERATOR S MANUAL KEEP HANDS OUT OF INLET AND DISCHARGE OPENINGS WHILE MACHINE IS RUNNING ROTATING BLADES ARE INSIDE TURN ENGINE OFF AND ALLOW IMPELLER TO COME TO COMPLETE STOP BEFORE REMOVING BAG DO NOTATTEMPT TO CLEAR A CLOG OR JAM WITH THE ENGINE RUNNING DO NOT OPERATE UNIT WITHOUT BAG OR OPTIONAL BLOWER CHUTE IN PLACE DO NOT STAND OR WALK IN FRONT OF BLOWER CHUTE OR AIM IT AT BYSTANDERS OBJECTS THROWN OUT OF DISCHARGE CAN CAUSE PERSONAL INJURY DO NOT OPERATE WHEN CHILDREN OR OTHERS ARE AROUND WEAR APPROVED SAFETY GLASSES 30599 WARNING YOUR RESPONSIBILITY Restrict the use of this power machine to persons who read understand and follow the warnings and instructions in this manual and on the machine O KEEP HANDS OUT OF INLETS WHILE ENGINE IS STOP RUNNING ROTATING BLADES ARE INSIDE TITT g 530258 SECTION 2 ASSEMBLING YOUR YARD VACUUM IMPORTANT This unit is shipped without gasoline or oil in the engine Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine NOTE Reference to right or left hand side of the Yard Vacuum is observed from the operating pos
9. an optional feature on some model yard vacuums It is NOT standard equipment If your unit is not equipped with a blower chute contact Customer Support as instructed on page 2 for information regarding price and availability e Grasp blower chute with one hand and slide locking rod on mounting bracket with other hand toward engine Use end of mounting bracket as leverage when sliding the locking rod See Figure 5 Slip blower chute over rim of the discharge opening and release locking rod to secure chute in place Make sure the safety switch button is fully depressed by the front tab on the blower chute e Raise the nozzle height to the highest setting when using the blower chute Refer to nozzle height adjustment in the OPERATION section Blower Chute Locking SECTION 3 KNOW YOUR YARD VACUUM Starter Handle Bag Handle Bracket Nozzle Height Adjustment Lever Hose Assembly Blower Chute Nozzle Figure 6 Read this operators manual and safety rules before operating your Yard Vacuum Compare the illustrations in Figure 6 with your unit to familiarize yourself with the location of various controls and adjustments WARNING The operation of any Yard A Vacuum can result in foreign objects being thrown into the eyes which can result in severe eye damage Always wear safety glasses provided with the Yard Vacuum for operating this equipment or while performing any adjustments or repairs on it Starter
10. clusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above exclusions or limitations may not apply to you In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold Alteration of safety features of the product shall void this warranty You assume the risk and liability for loss damage or injury to you and your property and or to others and their property arising out of the misuse or inability to use the product This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift HOW STATE LAW RELATES TO THIS WARRANTY This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state IMPORTANT Owner must present Original Proof of Purchase to obtain warranty coverage Troy Bilt LLC P 0 BOX 361131 CLEVELAND OHIO 44136 0019 Phone 1 866 840 6483 1 330 558 7220
11. connect the spark plug wire ground it against the engine and perform the following steps a Inspect for damage b Repair or replace any damaged parts c Check for any loose parts and tighten to assure continued safe operation Do not allow an accumulation of processed material to build up in the discharge area This can prevent proper discharge and result in kickback of material through the feed opening Do not attempt to shred or chip material larger than specified on the machine or in this manual Personal injury or machine damage could result Never attempt to unclog either the feed intake or discharge opening while the engine is running Shut the engine off wait until all moving parts have stopped disconnect the spark plug wire and ground it against the engine before clearing debris Never operate without vacuum bag and discharge chute properly attached to the machine Never empty or change vacuum bag while the engine is running Zippered end of vacuum bag must be kept closed at all times during operation 10 12 13 14 15 16 Never operate without either the inlet nozzle or optional hose attachment properly attached to the machine Never attempt to attach or change either attachment while the engine is running Keep all guards deflectors and safety devices in place and operating properly Keep your face and body back and to the side of the chipper chute while feeding material into the machine to av
12. dapter to operate the hose assembly e Unhook the hose from upper handle bracket and grasp the hose handle to guide while vacuuming yard waste such as leaves or pine needles in hard to reach places Nozzle Hose Vac Handle Bottom Position Spring Loaded Second Hole Figure 9 Nozzle Height Adjustment The nozzle can be adjusted to any six positions ranging from 5 8 to 4 1 8 ground clearance The nozzle height has to be adjusted according to the conditions Move the height adjustment levers forward or backward to adjust the nozzle upwards or downwards Make sure both levers are in the same position See Figure 10 NOTE n general raise the nozzle height to vacuum a thick layer of leaves or to operate with the blower chute if equipped and lower the nozzle height for smoother surfaces Nozzle Height Adjustment Lever Figure 10 SECTION 5 MAINTAINING YOUR YARD VACUUM Customer Responsibilities MAINTENANCE SCHEDULE Lubricate Wheels SERVICE Lubricate Nozzle Levers Lubricate Locking Rod PRODUCT Lubricate Nozzle Hose Handle Check Chipper Blade Change Oil Check Air Filter Clean Engine Check Spark Plug WARNING Always stop engine and disconnect spark plug wire before cleaning lubricating or doing any kind of maintenance on your machine A Lubrication Wheels Lubricate each wheel shoulder screw once a season with light oil Refer to Figure
13. eenaeeeeeeeeaeeeeseeaeeeeseeeaeeeeeseaaes 10 TBOUBIGS MO OUI 535s rica lacs tats due esa S 13 Parts LiSt cccvecie edie teeta an in edi es evs eben ni evi 14 FINDING MODEL NUMBER This Operator s Manual is an important part of your new Yard Vacuum It will help you assemble prepare and maintain the unit for best performance Please read and understand what it says Before you start assembling your new equipment please locate the model plate on the equipment and copy the information from it in the space provided below The information on the model plate is very important if you need help from our Customer Support Department or an authorized dealer You can locate the model number by looking down at the rear of the Yard Vacuum A sample model plate is explained below For future reference please copy the model number and the serial number of the equipment in the space below Model Number Serial Number Copy the model number here TROY BIT LLC Copy the serial number here OTROV BILT BOX 361131 www troybilt com CLEVELAND OH 44136 330 558 7220 866 840 6483 ENGINE INFORMATION The engine manufacturer is responsible for all engine related issues with regards to performance power rating specifications warranty and service Please refer to the engine manufacturer s Owner s Operator s Manual packed separately with your unit for more information CALLING CUSTOMER SUPPORT If you have difficulty asse
14. firm grip on starter handle Let rope rewind slowly e Repeat previous steps until engine fires When engine starts move choke control if equipped gradually to RUN position WARNING Never run the engine indoors A or in a poorly ventilated area Engine exhaust contains carbon monoxide an odorless and deadly gas Stopping Engine Move throttle control lever to STOP or OFF position Disconnect spark plug wire from spark plug and ground against the engine 1o Empty Bag Unhook bag straps from the lower handle and unsnap bag clip from the top of lower handle See Figure 7 e Grasp bag handle with one hand and pull lock rod on mounting bracket with other hand toward engine to release e Remove bag from rim of the discharge opening Refer to Figure 4 e Twist the two buttons on the back of the bag to unlock and empty contents See Figure 7 e Hold bag handle and bag clip while emptying the contents Compress bag opening and fold inner flap over opening Fold outer flap over inner flap and insert buttons on the bag through metal outlets e Twist the buttons to lock bag Figure 7 To Remove Blower Chute if Equipped e Grasp blower chute with one hand and pull lock rod on mounting bracket with other hand toward engine to release Refer to Figure 5 Remove blower chute from rim of the discharge opening Using the Nozzle Vacuum e Place nozzle hose vac handle in the top position on the nozzle to vacuum
15. ion of the controls on the engine SECTION 4 OPERATING YOUR YARD VACUUM WARNING The operation of the Yard A Vacuum can result in foreign objects being thrown into the eyes which can damage your eyes severely Always wear the safety glasses provided with this unit or eye shields before chipping or blowing and while performing any adjustments or repairs Gas And Oil Fill Up Service the engine with gasoline and oil as instructed in the separate engine manual packed with your Yard Vacuum Read instructions carefully WARNING Never fill fuel tank indoors with A engine running or until the engine has been allowed to cool for at least two minutes after running Starting Engine Attach spark plug wire to spark plug Make certain the metal cap on the end of the spark plug is fastened securely over the metal tip on the spark plug e Make sure safety switch wire is connected to engine and properly grounded e Engines with choke lever Move choke lever on engine to CHOKE position A warm engine may not require choking Engines with primer Prime engine as instructed in separate engine manual e The throttle control is located on the engine Move engine throttle control lever to FAST or ON position e Stand behind unit grasp starter handle and pull rope out slowly until engine reaches start of compression cycle rope will pull slightly harder at this point e Pull rope with a rapid continuous full arm stroke Keep a
16. ition Removing Unit From Carton Remove staples break glue on top flaps or cut tape at carton end and peel along top flap to open carton e Remove loose parts if included with unit i e operator s manual etc e Cutalong corners lay carton down flat and remove packing material e Roll or slide unit out of carton and check carton thoroughly for loose parts Loose Parts In Carton see Figure 1 e Handle Assembly Bag e Blower Chute If Equipped e Hose Assembly Disconnecting Spark Plug Wire Before setting up your Yard Vacuum disconnect the spark plug wire from the spark plug and ground to a stud on the engine Upper Handle Blower Chute ower C ute SS Rope Guide Handle Hose Assembly If Equipped Figure 1 Att Att aching The Handle Unfold the upper handle until it aligns with the lower handle Secure the two handles by tightening the wing nuts carriage bolts must be seated properly into the handle See Figure 1 Remove the hairpin clips from the handle brackets on the Yard Vacuum and remove the carriage bolts and wing nuts from the lower handle See Figure 2 Place the bottom holes in lower handle over pins on handle brackets and secure with hairpin clips Insert carriage bolts through upper hole in lower handle from the outside and secure with wing nuts Figure 2 Loosen the wing nut that secures the rope guide to the right side of upper handle Pull the starter rope o
17. lters blade sharpening tune ups brake adjustments clutch adjustments deck adjustments and normal deterioration of the exterior finish due to use or exposure d Service completed by someone other than an authorized service dealer e Troy Bilt does not extend any warranty for products sold or exported outside of the United States its possessions and territories except those sold through Troy Bilt s authorized channels of export distribution f Replacement parts that are not genuine Troy Bilt parts g Transportation charges and service calls No implied warranty including any implied warranty of merchantability of fitness for a particular purpose applies after the applicable period of express written warranty above as to the parts as identified No other express warranty whether written or oral except as mentioned above given by any person or entity including a dealer or retailer with respect to any product shall bind Troy Bilt During the period of the warranty the exclusive remedy is repair or replacement of the product as set forth above The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale Troy Bilt shall not be liable for incidental or consequential loss or damage including without limitation expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product Some states do not allow the ex
18. mbling this product or have any questions regarding the controls operation or maintenance of this unit please call the Customer Support Department Call 1 330 558 7220 or 1 866 840 6483 to reach a Customer Support representative Vi Please have your unit s model number and serial number ready when you call See previous section to locate this information You will be asked to enter the serial number in order to process your call For more details about your unit visit our website at www troybilt com SECTION 1 IMPORTANT SAFE OPERATION PRACTICES 1 WARNING This symbol points out important safety instructions which if not followed could endanger the personal safety and or property of yourself and others Read and follow all instructions in this manual before attempting to operate this machine Failure to comply with these instructions may result in personal injury When you see this symbol heed its warning WARNING Engine Exhaust some of its constituents and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm DANGER This machine was built to be operated according to the rules for safe operation in this manual As with any type of power equipment carelessness or error on the part of the operator can result in serious injury This machine is capable of amputating hands and feet and throwing objects Failure to observe the follo
19. misuse abuse commercial use neglect accident improper maintenance alteration vandalism theft fire water or damage because of other peril or natural disaster Damage resulting from the installation or use of any part accessory or attachment not approved by Troy Bilt for use with the product s covered by this manual will void your warranty as to any resulting damage Normal wear parts are warranted to be free from defects in material and workmanship for a period of thirty 30 days from the date of purchase Normal wear parts include but not limited to items such as batteries belts blades blade adapters grass bags rider deck wheels seats snow thrower skid shoes shave plates auger spiral rubber and tires HOW TO OBTAIN SERVICE Warranty service is available WITH PROOF OF PURCHASE through your local authorized service dealer To locate the dealer in your area check your Yellow Pages or contact Troy Bilt LLC at P O Box 361131 Cleveland Ohio 44136 0019 or call 1 866 840 6483 or 1 330 558 7220 or log on to our Web site at www troybilt com This limited warranty does not provide coverage in the following cases a The engine or component parts thereof These items may carry a separate manufacturer s warranty Refer to applicable manufacturer s warranty for terms and conditions b Log splitter pumps valves and cylinders have a separate one year warranty C Routine maintenance items such as lubricants fi
20. nine screws that secure the lower housing to the upper housing See Figure 14 Figure 14 Remove lock nut that secures flail screen to the lower housing The flail screen does not have to be removed Refer to Figure 11 Remove the hex bolt lock washer and flat washer that secure the impeller assembly to the crankshaft See Figure 15 Impeller Assembly BOTTOM VIEW Figure 15 e Apply lubricant to the threads of impeller removal tool and then thread the tool into the crankshaft Stop when the impeller assembly can move on the crankshaft e Remove the impeller assembly from the crankshaft Unthread the impeller removal tool from the impeller assembly e Remove the blade using a 3 16 allen wrench on the outside of the blade and 1 2 wrench on the impeller assembly e Replace or sharpen chipper blade e When sharpening blade protect hands by using gloves and follow the original angle of grind e Reassemble by performing the previous steps in reverse order e Tighten blade screws to 210 250 in lbs Tighten impeller bolt to 375 425 in lbs NOTE Make certain chipper blade is reassembled with the sharp edge facing upward See Figure 16 __ Chipper Impeller Assembly Figure 16 Storing Your Yard Vacuum e Clean the equipment thoroughly e Wipe equipment with a oiled rag to prevent rust e Refer to engine manual for correct engine storage instructions e Store unit in a
21. oid accidental kickback injuries Never operate this machine without good visibility or light Always be sure of your footing and keep a firm hold on the handles Do not operate this machine on a gravel surface Do not operate this machine while under the influence of alcohol or drugs Muffler and engine become hot and can cause a burn Do not touch Never pick up or carry machine while the engine is running MAINTENANCE AND STORAGE 1 2 Never tamper with safety devices Check their proper operation regularly Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition Also visually inspect machine for any damage and repair if needed Before cleaning repairing or inspecting stop the engine and make certain the impeller and all moving parts have stopped Disconnect the spark plug wire and ground it against the engine to prevent unintended starting Do not change the engine governor settings or overspeed the engine The governor controls the maximum safe operating speed of the engine Maintain or replace safety and instruction labels as necessary Follow this manual for safe loading unloading transporting and storage of this machine Never store the machine or fuel container inside where there is an open flame spark or pilot light such as a water heater furnace clothes dryer etc Always refer to the operator s manual for proper instructions on off season stor
22. plug gap too close 1 Adjust gap to 030 at high speed Unit does not discharge 1 Discharge chute clogged 1 Stop engine immediately and disconnect spark plug wire Clean flail screen and inside of discharge opening 2 Foreign object lodged in impeller 2 Stop engine and disconnect spark plug wire Remove lodged object 3 Low engine RPM 3 Always run engine at full throttle 4 Vacuum bag is full 4 Empty bag Rate of discharge slows 1 Low engine RPM 1 Always run engine at full throttle considerably or 2 Chipper blade dull 2 Replace chipper blade or see your composition of discharged material changes authorized service dealer NOTE For repairs beyond the minor adjustments listed above contact your nearest authorized service dealer MANUFACTURER S LIMITED WARRANTY FOR OTROY BILT The limited warranty set forth below is given by Troy Bilt LLC with respect to new merchandise purchased and used in the United States its possessions and territories Troy Bilt warrants this product against defects in material and workmanship for a period of two 2 years commencing on the date of original purchase and will at its option repair or replace free of charge any part found to be defective in materials or workmanship This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator s Manual furnished with the product and has not been subject to
23. r running e Allow engine to cool at least two minutes before refueling f Never over fill fuel tank Fill tank to no more than 1 2 inch below bottom of filler neck to provide space for fuel expansion g Replace gasoline cap and tighten securely h If gasoline is spilled wipe it off the engine and equipment Move machine to another area Wait 5 minutes before starting the engine i Never store the machine or fuel container inside where there is an open flame spark or pilot light e g furnace water heater space heater clothes dryer etc j To reduce a fire hazard keep machine free of grass leaves or other debris build up Clean up oil or fuel spillage and remove any fuel soaked debris k Allow machine to cool at least 5 minutes before storing OPERATION 1 Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening Contact with the rotating impeller can amputate fingers hands and feet Before starting the machine make sure the chipper chute feed intake and cutting chamber are empty and free of all debris Thoroughly inspect all material to be shredded and remove any metal rocks bottles cans or other foreign objects which could cause personal injury or damage to the machine If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration immediately shut the engine off Allow the impeller to come to a complete stop Dis
24. ut of the engine slowly and slip the starter rope into the rope guide Tighten the wing nut aching The Hose Assembly Slide hose adapter of hose assembly into the base adapter located on the left front of the Yard Vacuum See Figure 3 Pull spring loaded pin out on the base and align pin with the first hole in the hose adapter Release the pin to lock the hose in place Connect the hose handle near nozzle end of hose to the side bracket on the upper handle Refer to Figure 6 Snap hose handle to the lower handle bracket to secure in place and lay hose tubing on side hanger bracket next to chipper chute Refer to Figure 6 Hose Adapter Spring Loaded Pin fa Att Figure 3 aching The Bag Grasp bag handle with one hand and slide locking rod on mounting bracket with other hand toward engine Use the end of mounting bracket as leverage when sliding the locking rod See Figure 4 Slip bag over the rim of the discharge opening and release locking rod to secure bag in place Place the straps on the bag over the lower handle hooking them on the studs Snap bag clip to the top of the lower handle NOTE The safety switch button attached to the mounting bracket must be fully depressed by the front tab on the bag handle when securing the bag or the engine will not start See Figure 4 Figure 4 Attaching The Blower Chute If Equipped NOTE The blower chute is
25. wing safety instructions could result in serious injury or death TRAINING Read understand and follow all instructions on the machine and in the manual s before attempting to assemble and operate Keep this manual in a safe place for future and regular reference and for ordering replacement parts Be familiar with all controls and their proper operation Know how to stop the machine and disengage them quickly Never allow children under 16 years old to operate this machine Children 16 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent Never allow adults to operate this machine without proper instruction Keep bystanders helpers pets and children at least 75 feet from the machine while it is in operation Stop machine if anyone enters the area Never run an engine indoors or in a poorly ventilated area Engine exhaust contains carbon monoxide an odorless and deadly gas Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening Contact with the rotating impeller can amputate fingers hands and feet Never attempt to unclog either the feed intake or discharge opening remove or empty vacuum bag or inspect and repair the machine while the engine is running Shut the engine off and wait until all moving parts have come to a complete stop Disconnect the spark plug wire and ground it against
Download Pdf Manuals
Related Search