Tricity Bendix TBG700 User's Manual
Contents
1. taps ignition switches Check continuity from ignition Change the ignitor unit Switches connector to ignitor unit 25 TRICITY BENDIX Commissioning When the hob has been fully installed it will be necessary to check the minimum flame Setting To do this follow the procedure below ce 1 Turn the gas tap to the MAX position and ignite 2 Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times If the flame is unstable or is extinguished follow the procedure below Procedure ce 1 Re ignite the burner and setto MIN 2 Remove the control knob 3 To adjust use a thin bladed screwdriver and turn the adjustment screw See diagram until the flame is steady and does not extinguish when the knob is turned from MIN to MAX Repeat this procedure for Ge S all burners Minimum adjustment screw Pressure Testing The pressure testing must becarried out on the burners ce Proceed as follows 1 Remove the pan supports and the burner caps and crowns 2 Fit manometer tube over the injector 3 Turn on the burner gas supply and ignite another burner supply The pressure reading should be nominally 20 mbar and must be between 17 mbar and 25 mbar 4 Turn off the burner supplies 26 E TRICITY BENDIX Conversion from Natural Gas to LPG Z IMPORTANT The replacement conversion from natural gas to LPG should only be undertaken by a competent person Itis importantto note2. Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped if fitted Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly e g after cleaning Check the main jet is not blocked and the burner crown is clear of food particles Check the burner cap and crown have been replaced correctly e g after cleaning H after all these checks your hob still does not operate correctly contact your local Service Force Centre Please note that it will be necessary to provide proof of purchase for any in guarantee service calls In guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown 12 TRICITY BENDIX Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width 680 mm Depth 510mm Height 72 mm CUT OUT DIMENSIONS Width 560 mm Depth 480 mm Thickness 30 mm SUPPLY CONNECTIONS Gas R 1 2 inch 1 2 inch male Rear righthand corner Electric 230 V 50 Hz supply 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse HEAT INPUT Rear Left Burner 2 0 kW 6826 BTU HR semi rapid Front Right Burner 3 0 kW Natural Gas 10239 BTU HR rapid 2 8 kW LPG 9556 BTU HR Rear Right Burner 2 0 kW 6826 BTU HR semi rapid Central Burner 4 0 kW 13652 BTU HR tri
3. Centre must undertake all service work under this guarantee Any appliance or defective part replaced shall become the Company s property This guarantee is in addition to your statutory and other legal rights Exclusions Damage or calls resulting from trans portation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom Appliances found to be in use within a commercial environment plus those which are subject to rental agreements Products of Electrolux manufacturer thatare not marketed by Electrolux 28 TRICITY BENDIX Service and Spare Parts In the event of your appliance requiring service or if you wish to purchase spare parts please contact your local Service Force Centre by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre co vering your postcode area Forthe address of your local Service Force Centre and further information about Service Force please visitthe website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading Something notworking When you contactthe Service Force Centre you will need to give the follo wing details 1 Your name address and postcode 2 Your telephone number 3 Clear concise d
4. can become tarnished if excessively heated Therefore prolonged cooking with potstones earthenware pans or cast iron plates is inadvisable Also do not use aluminium foil to protect the top during use Make sure pots do not protrude over the edges of the cooktop and that they are centrally positioned on the rings in order to obtain lower gas consumption Do not place unstable or deformed pots on the rings they could tip over or spill their contents causing accidents Pots must not enter the control zone TRICITY BENDIX Maintenance and Cleaning A Before any maintenance or cleaning can be carried out you must DISCONNECT the hob from the electricity supply A The hob is best cleaned whilst it is still warm as spillage can be removed more easily than if it is left to cool A This appliance cannot be cleaned with steam or with a steam cleaning machine The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little wasing up liquid has been added Avoid the use of the following household detergent and bleaches impregnated pads unsuitable for non stick saucepans steel wool pads bath sink stain removers Should the hob top become heavily soiled the following products are recommended For stainless steel hobs use a proprietary stainless steel cleaner For other hobs use Hob Brite or Bar Keepers Friend A Do not leave acid or alkaline substances e g vinegar s
5. on the bottom of the hob A copy is attached on the back cover of this book The hob is supplied with a 3 core flexible supply cord incorporating a 3 amp plug fitted In the event of having to change the fuse a 3 amp ASTA approved BS 1362 fuse must be used Should the plug need to be replaced for any reason the wires in the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live L 1 Connect the green and yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow Connect the blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black Connect the brown live wire to the terminal in the plug which is marked with the letter L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord Clamp must be secure over the outer sheath bd A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely A The replacement of electric cable must be carried out exclusively by the service force centre or by personnel with similar competencies in accordance with the current regulations 21 GREEN amp YELLOW 3 AMP FUSE 2 3 TRICITY BENDIX Permanent Connection In the case of a permanent connection it is necessary that y
6. thatthis model is designed for use with natural gas butcan be converted foruse with butane or propane gas providing the correct injectors are fitted The gas rate is adjusted to suit Method CS 1 Ensure thatthe gas taps are in the OF F position 2 Isolate the hob from the electricity supply 3 Remove all pan supports burner caps rings crowns and control knobs 4 With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate LPG injectors TO ADJ UST THE GAS RATE With the aid of a thin bladed screwdriver completely tighten down the by pass adjustmentscrew Upon completion stick the replacement rating plate on the under side of the hob 27 TRICITY BENDIX Standard Guarantee Conditions We Electrolux undertake thatif within 12 months of the date of the purchase this Electrolux appliance or any partthereofis proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us Electrolux Service Force
7. 0 Electrical een 21 Wining Diagram ET 22 ell EE 23 COMMISSIONING EE 26 Conversion from Natural Gas to LPG oeren a 27 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions Safety Instructions Step by step instructions for an operation Hints and Tips Environmental information e64 TRICITY BENDIX Important Safety Information You MUST read these warnings carefully before installing or using the hob If you need assistance contact our Customer Care Department on 08705 950950 Installation e This appliance must be installed and serviced by a competent person as stated in the Gas Safety Installation and Use Regulations Current Editions and the IEE Wiring Regulations e For appliances installed in the Republic of Ireland please refer to NSAl Domestic Gas Installations 813 Current Editions and the ETCI Rules for Electrical Installations e Remove all packaging before using the hob e Ensure that the gas and electrical supply complies with the type stated on the rating plate located near the gas supply pipe Do not attempt to modify the hob in any way Child Safety e This hob is designed to be operated by adults Do not allow children to play near or with the hob e This appliance is not intended for use by children or other persons whose physical sensory or mental capabilities or lack of experience and knowledge prevents them from using the appliance
8. alt lemon juice etc on the cooktop Pan Supports The pan supports are dishwasher proof If washing them by hand take care when drying them as the enamelling process occasionally leaves rough edges If necessay remove stubborn stains using a paste cleaner After cleaning make sure that the pan supports are correctly positioned To make burners work properly ensure that pan supports are placed in a way that the arms are centred upon the burner as shown in the picture A Pay attention when replacing the pan supports in order to avoid damaging the hob top 10 E TRICITY BENDIX The Burners The burner caps and crowns can be removed for cleaning Wash the burners caps and crowns using hot soapy water and remove marks with a mild paste cleaner A well moistened soap impregnated steel wool pad can be used with caution if the marks are particularly difficult to remove After cleaning be sure to wipe dry with a soft cloth The Ignition electrode The electric ignition is obtained through a ceramic electrode and a metal electrode Keep these components very clean to avoid difficult lighting and check that the burner crown holes are not obstructed 11 TRICITY BENDIX Something Not Working If the hob is not working correctly please carry out the following checks before contacting your local Service Force Centre SYMPTOM a There is no spark when lighting the gas a The gas ring burns unevenly SOLUTION
9. b and installation Ensure thatthe main connection pipe does not exertany strain on the hob WHEN THE HOB IS FIRST INSTALLED bd Once the hob has been installed it is important to remove any protective materials which were put on in the factory On the end of the shaft which includes the GJ 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts together without using excessive force A Itis important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe Failure to ensure the correct assembly will cause leakage of gas A Endofshaftwith nut B Washer C Elbow 17 i TRICITY BENDIX Cut Out Size The dimensions of the cut out are given in the diagram 18 TRICITY BENDIX Building In Building over a cupboard or drawer Ifthe hob is to be installed above a cupboard or drawer it will be necessary to fita heat resistant board below the base of the hob on the underside of the work surface Itis also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 Building over a kitchen unit with Jonorr swen door Proper arrangements must be taken in designing the Bs furniture unit in order to avoid any contact with the bottom ofthe hob which can be heated when itis operated The recommended solution is shown in diagram 3 The panel fit
10. d not be used on the hob as unstable pans can cause an accident by tipping or spillage e Never leave the hob unattended when cooking with oil and fats e Never use plastic or aluminium foil dishes on the hob e Perishable food plastic items and areosols may be affected by heat and should not be Stored above or below the hob unit e This appliance cannot be cleaned with steam or with a steam cleaning machine Service e This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used Environmental Information e After installation please dispose of the packaging with due regard to safety and the environment e When disposing of an old appliance make it unusable by cutting off the cable e Thesymbol IS on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product These instructions are only valid for count
11. etails of the fault 4 The model and Serial number of the appliance found on the rating plate 5 The purchase date Please note a valid purchase receipt or guarantee documentation is required for in guarantee service calls Customer Care For general enquiries concerning your Electrolux appliance or for further information on Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www electrolux co uk Customer Care Department Electrolux Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Tel 08705 950 950 Calls may be recorded for training purposes 29 K L TRICITY BENDIX European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual for the period specified in the appliance guarantee or otherwise by law If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications e The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purchase document issued by the seller of the appliance e The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new country of residence for this particular model or range of appliances e The appliance guarantee is
12. i TRICITY BENDIX C 4 h 4 gt User Manual K L P 4 R g Gas Hob d K L e TBG700 J i TRICITY BENDIX Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux which hopefully will provide you with lots of pleasure in the future The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable You find some examples on the cover in this manual Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine We promise that it will provide a superior User Experience delivering Ease of Mind Good luck TRICITY BENDIX Contents Important Safety Informati tenants nesaet aing rnrannttats 4 IRSHUCEONS for CAT 8 Set 6 B le EE 8 Maintenance and Cl aniNg EE 10 Something Not dl die EE 12 Standard Guarantee Conditions scsarasnseesipasninn tnuatnninsdahateantinasadnantuntoainssnnaiilansanapsidiones 28 Service and Spar Tc 29 European EE TTT 30 Instructions for the Installer sssssssssssrssnsssrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannnnnnannnnn 13 Engineer technical 099 eenn 13 Important safety requirements ss ssssssssssirrsssssssantnrtnsnnnnnnnnnnnnnnnnnannnnnnnnnnrnntnnnnnnaanrnnnnn 15 Astala tOM siiis aaa 16 E EE 17 BEES 18 Bilding a re a ee re ree eer Tr 19 Fitting the Hob into Te WN OTRE eege eenegen 2
13. mum distance combustible material can be fitted directly above the hob is 700 mm For appliances installed in the Republic of Ireland please refer to NSAI Domestic Gas Installation S 813 Current E dition Section 7 Permitted Locations of Appliance 15 TRICITY BENDIX CLEARANCES REQUIRED CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WHEN FITTING THE GAS HOB WITHOUT ACOOKER HOOD ABOVE WITH A COOKER HOOD ABOVE 600 mm Installation IMPORTANT A This hob must be installed by a competent person to the relevant Gas Standards A Any gas installation must be carried out by a registered competent person Please ensure that once the hob is installed it is easily accessible for the engineer in the event of a breakdown The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored On the end of the shaft which includes the G 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts together without using excessive force 16 TRICITY BENDIX Gas Connection Connection to the gas supply should be with either rigid or semi rigid pipe i e steel or copper The connection should be suitable for connecting to R 1 2 1 2 BSP male thread When the final connection has been made itis essential that a thorough leak testis carried outon the ho
14. ogdani Nr 7 Tirane Bergensesteenweg 719 1502 Lembeek Bud jovicka 3 Praha 4 140 21 Sj llandsgade 2 7000 Fredericia Muggenhofer Str 135 90429 Nurnberg Mustam e tee 24 10621 Tallinn Carretera M 300 Km 29 900 Alcala de Henares Madrid Addington Way Luton Bedfordshire LU4 9QQ 4 Limnou Str 54627 Thessaloniki Slavonska avenija 3 10000 Zagreb Long Mile Road Dublin 12 C so Lino Zanussi 26 33080 Porcia PN Kr Barona iela 130 2 LV 1012 Riga Verkiy 29 09108 Vilnius Lithuania Rue de Bitbourg 7 L 1273 Hamm H 1142 Budapest XIV Erzs bet kir lyn tja 87 Vennootsweg 1 2404 CG Alphen aan den Rijn Rislokkvn 2 0508 Oslo Herziggasse 9 1230 Wien ul Kolejowa 5 7 Warsaw Quinta da Fonte Edificio Gongalves Zarco Q 35 2774 518 Pago de Arcos B dul Timisoara 90 S6 Bucharest Industriestrasse 10 CH 5506 Magenwil Electrolux Ljubljana doo Gerbi eva 98 1000 Ljubljana Electrolux Slovakia s r o Electrolux Dom ce spotrebi e SK Seber niho 1 821 03 Bratislava Electrolux Service S t G ransgatan 143 S 105 45 Stockholm Tarlaba caddesi no 35 Taksim stanbul 129090 Mockpa Onnmnn ckn npocnekr 16 BU Onumnuk 31 www electrolux com www tricity bendix co uk 35674 6903 02 07 R O
15. or continuity and all contacts clean and tight B INSULATION CHECK Appliance electrically disconnected all switches ON a meter set on W Ohms x 1 scale Test leads from L to N in appliance terminal block If meter reads 0 then there is a short circuit b meter set on W Ohm x 100 scale Repeat test with leads from L to E If meter reads less than x infinity there is a fault NOTE Should it be found that the fuse has failed but no fault is indicated a detailed continuity check i e by disconnecting and checking each component is required to trace the faulty component Itis possible that a fault could occur as a result of local burning arcing but no fault could be found under test However a detailed visual inspection should reveal evidence of burning around the fault 24 TRICITY BENDIX Ignition System Gas Ignition YES Ignitor does not spark aoe supply at NO SEET Light bumer manually replace if necessary Check polarity and earth Check by pass simmer continuity of supply point adjusted Check fitting of bumers Check position of the electrode Check earth continuity of appliance Check continuity from N on the Check continuity from the tip of mains connector block and O on each electrode to the terminals 1 to 4 on the ignitor unit the ignitor unit Check continuity from L on the mains connector block and the Check for breaks in the insulation of the HT leads
16. ou install a double pole Switch between the hob and the electricity supply mains with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations The switch must not break the yellow and green earth cable at any point bd Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg C Wiring Diagram L 1 Ignitor switches 2 Ignitor unit 22 TRICITY BENDIX Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out A Earth Continuity check NO YES Carry out C Polarity check Cary out D Resistance to Earth check Has inlet fuse blown NO YES Electricity supply should now be satisfactory PLUG with cover removed SOCKET Inlet wiring Gong face view _ faulty a Ire Rectify any Green Y ellow fault Neutral Wire Blue Isolate appliance and carry out B Insulation check Rectify any fault including replacing fuses as necessary 23 TRICITY BENDIX A EARTH CONTINUITY CHECK Appliance must be electrically disconnected meter set on W Ohms x 1 scale and adjust zero if necessary Test leads from any appliance earth point to earth pin on plug Resistance Should be less than 0 1 W Ohm check all earth wires f
17. personal to the original purchaser of the appliance and cannot be transferred to another user e The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home i e is not used for commercial purposes e The appliance is installed in accordance with all relevant regulations in force within your new country of residence The provisions of this European Guarantee do not affect any of the rights granted to you by law 30 TRICITY BENDIX www electrolux com EN Albania Belgique Belgi Belgien Ceska republika Danmark Deutschland Eesti Espana France Great Britain Hellas Hrvatska Ireland Italia Latvija Lituania Luxembourg Magyarorsz g Nederland Norge sterreich Polska Portugal Romania Schweiz Suisse Svizzera Slovenija Slovensko Suomi Sverige T rkiye Poccna a 35 5 4 261 450 32 2 363 04 44 420 2 61 12 61 12 45 70 11 74 00 49 180 32 26 622 37 2 66 50 030 34 902 11 63 88 www electrolux fr 44 8705 929 929 30 23 10 56 19 70 385 1 63 23 338 353 1 40 90 753 39 0 434 558500 37 17 84 59 34 370 5 27 80 609 35 2 42 43 13 01 36 1 252 1773 31 17 24 68 300 47 81 5 30 222 43 18 66 400 48 22 43 47 300 35 12 14 40 39 39 40 21 451 20 30 41 62 88 99 111 38 61 24 25 731 421 2 43 33 43 22 www electrolux fi 46 0 771 76 76 76 90 21 22 93 10 25 7 095 937 7837 tll Rr Pjeter B
18. ple crown Front Left Burner 1 0 kW 3413 BTU HR auxiliary APPLIANCE CLASS 3 APPLIANCE CATEGORY I2H3 GAS SUPPLY Natural gas G20 2H 20 mbar C This appliance is manufactured according to the following EEC directives 2006 95 EEC 93 68 EEC 89 336 EEC 90 396 EEC current edition 13 E TRICITY BENDIX BURNER RAPID SEMI RAPID AUXILIARY TRIPLECROWN TYPE OF GAS POSITION MAX MIN MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER HR 3 0 O65 2 0 O45 ISU OG 90 13 NATURAL GAS 20 mbar NOMINAL FLOW VALUE RATE mh 0 286 0 062 0 190 0 043 0 095 0 031 0 381 0 114 37 78 MJ m E r E Ws 50 7 MJ m NOZZLE REFERENCE 119 Adjust 96 Adjust 70 Adjust 146 Adjust 1 100 mm NOMINAL THERMAL LPG GAS POWER W 28 loosi 2 0 1045 pio 10 38 4 0 2 28 30 37 mbar VALUE NOMINAL FLOW NOZZLE REFERENCE 86 40 11 32 50 28 98 56 1 100 mm Burner Dia Tap By pass 1 100mm Auxiliary 28 Semi rapid 32 Rapid 40 Triple crown 56 Aeration adjustment none 14 TRICITY BENDIX Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regulations Current Edition and the IEE Wiring Regulations Current Edition For appliances installed in the Republic of Ireland please referto NSAI Domestic Gas Installation S 813 Current E ditions and the ETC Rules for Electrical Installations Provision for Ventilation Detailed recommendations are contained in the following British Standards Code
19. required If the burner does not ignite turn the control knob to zero and try again When switching on the mains after installation or a power cut itis quite normal for the spark generator to be activated automatically In the absence of electricity ignition can occur without the electrical device in this case approach the burner with a flame push the relevant knob down and turn it anti clockwise until it reaches the maximum position H H H If the control knobs become difficult to turn please contact your local Service Force Centre Using the hob correctly To ensure maximum burner efficiency it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used so that flame will not spread beyond the bottom of the vessel see the table beside 00 Pee A A A TRICITY BENDIX Burner minimum maximum diameter diameter Triple crown 180 mm 260 mm Large rapid 180 mm 260 mm Medium semi rapid 120 mm 220 mm Small auxiliary 80 mm 160 mm As soon as a liquid starts boiling turn down the flame so that it will barely keep the liquid simmering Use only pans or pots with flat bottom If you use a saucepan which is smaller than the recommended size the flame will spread beyond the bottom of the vessel causing the handle to overheat Carefully supervise cooking with fat or oil since these types of foodstuff can result in a fire if over heated The stainless steel
20. ries whose identification symbols are shown on the cover of this instruction booklet and on the appliance itself Keep this instruction book for future reference and ensure it is passed on to any new owner i TRICITY BENDIX Description of the Hob Hob Top Semi rapid Burner Triple Crown Burner Rapid Burner Auxiliary Burner 10 Control Knobs L TRICITY BENDIX bd INSTALLATION Any gas installation must be carried out by a registered competent person and in accordance with existing rules and regulations The relevant instructions are to be found in the second section of this manual Please ensure that once the hob is installed itis easily accessible for the engineer in the event of a breakdown WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed it is important to remove any protective materials which were put on in the factory The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this book be ignored TRICITY BENDIX Hob burners control knobs The symbols on the knobs mean that 6 there is no gas supply M there is maximum gas supply A there is minimum gas supply Operation Lighting the burners EN For easier lighting proceed before putting a pan on the pan support E a light a burner e push in the relevant control knob and turn it anticlockwise to maximum position sq to ignite the burner Then adjust the flame as
21. s Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions The hob should notbe installed in a bed sitting room with a volume of less than 20 m If itis installed in a room of volume less than 5 mi an air vent of effective area of 110 cm is required If itis installed in a room of volume between 5 m and 10 m an air vent of effective area of 50 cm is required while if the volume exceeds 11 m no air ventis required However if the room has a door which opens directly to the outside no air ventis required even ifthe volume is between 5 m and 11 mi If there are other fuel burning appliances in the same room B S 5440 Part2 Current Edition should be consulted to determine the requisite air vent requirements For appliances installed in the R epublic of Ireland please refer to the NSAI Domestic Gas Installation LS 813 Current Editions Table F our Location The hob may be located in a kitchen a kitchen diner or bed sitting room butnotin a bathroom or shower room Before making the cutoutin the worktop ensure thatthere is a minimum distance of 55 mm between the rear edge of the hob and the wall A minimum distance of 100 mm mustbe left between the side edges of the hob and any adjacent cabinets or walls The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm If itis fitted below 400 mm a space of 50 mm 5mustbe allowed from the edges of the hob The mini
22. safely without supervision or instruction by a responsible person to ensure thatthey can use the appliance safely e The hob gets hot when itis in use Children should be kept away until it has cooled e Children can also injure themselves by pulling pans or pots off the hob During Use e This hob is intended for domestic cooking only Itis not designed for commercial or industrial purposes e This appliance is not connected to a combustion products evacuation device It must be installed and connected in accordance with current installation regulations Particular attention shall be given to the relevant requirements regarding ventilation e When in use a gas cooking hob will produce heat and moisture in the room in which it has been installed Ensure there is a continuous air supply Keeping air vents in good condition or installing a cooker hood with a venting hose e Ensure a good ventilation around the appliance A poor air supply could cause lack of oxygen e When using the hob for a long period time the ventilation should be improved by opening a window or increasing the extractor speed e Donotuse this hob if itis in contact with water Do not operate the hob with wet hands TRICITY BENDIX e Ensure the control knobs are in the OFF position when not in use e When using other electrical appliances ensure the cable does not come into contact with the hot surfaces of the cooking appliance e Unstable or misshapen pans shoul
23. ted under the hob a should be easily removable to allow easy access if technical assistance is needed The space behind the kitchen unit b can be used for connections Dimensions are given in mm TRICITY BENDIX Fitting the Hob into the Worktop Carry out the building in of the hob as follows 1 place the seals supplied with the hob on the front edge of the cut out Then place them at 50 mm from the side edges and at 10 mm from the rear edge as shown in the diagram taking care that the seals meet without overlapping 2 Place the hob in the cut out taking care that it is centred 3 Fix the hob with the relevant fixing clamps supplied with the injectors kit see diagram When the screws have been tightened the excess seal can be removed The edge of the hob forms a double seal which prevents the ingress of liquids 20 TRICITY BENDIX Electrical Connections A Any electrical work required to install this hob should be carried out by a qualified electrician or competent person in accordance with the current regulations THIS HOB MUST BE EARTHED The manufacturer declines any liability should these safety measures not be observed This hob is designed to be connected to a 230 V 50 Hz AC electrical supply Before switching on make sure the electricity supply voltage is the same as that indicated on the hob rating plate The rating plate is located
Download Pdf Manuals
Related Search