TRENDnet 24-Port User's Manual
Contents
1. TRENDNET TEG 240WS FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures VCCI Warning This is a product of VCCI Class A Compliance CORB T E e E BIR RISE Z VCCI OR CED PIA ATHENS COMBE CHATS d HERR Sta TC LE 0 ED COMA HERD VANER ET ZEDBRENSZCEMHVEF UL Warning a Elevated Operating Ambient Temperature If installed in a closed or multi unit rack assembly the operating ambient temperature of the rack environment may be greater than room ambient Therefore consideration should be given to installing the equipment in an environment compatible with the manufacturer s maximum rated ambient temperature Tmra b Reduc2. plug and play capability just need to plug in the network cable to the hub directly and don t care if the end node is NIC Network Interface Card or switch and hub These ports can operate in half duplex mode for 10 100Mbps and full duplex mode for 10 100 1000Mbps Note When the port is set to Forced Mode the Auto MDI MDIX will be disabled Mini GBIC Slots Port 23 24 The Switch is equipped with two combo mini GBIC ports supported optional 1000BASE SX LX mini GBIC module The 1000BASE T port 23 and 24 are the same ports with the mini GBIC port 23 and 24 when plug in the mini GBIC module the device will activate mini GBIC and the RJ45 port will be disabled Rear Panel The rear panel of the Switch consists of an AC power connector and Reset button The following shows the rear panel of the Switch RESRT A Vi Figure 5 Rear panel AC Power Connector This is a three pronged connector that supports the power cord Plug in the female connector of the provided power cord into this connector and the male into a power outlet Supported input voltages range from 100 240V AC at 50 60Hz Reset The Reset button is to reset all the setting back to the factory default Note Be sure that you recorded the setting of your device else all the setting will be erased when pressing the Reset button UNDERSTANDING LED INDICATORS The front panel LEDs provides instant status feedback and helps
3. Trap Setting Trap Setting Enabled Disabled TrapiP 172 21 81 48 System Events V Device Bootup Illegal Login Fiber Port Event V Link Up Link Down Twisted Pair Port Event Y Link Up Link Down Figure 29 Trap Setting System Events Monitoring the system s trap Device Bootup a trap when booting up the system Illegal Login a trap when there is using a wrong password login and it will record from where the IP to be login Fiber Port Event Monitoring the Fiber port status Link Up Link Down a trap when there is linking status happens in mini GBIC connection Twisted Pair Port Event Monitoring the twisted pair port status Link Up Link Down a trap when there is linking status happens in 1000BASE T connection 56 Password Setting Setting a password is an invaluable tool for managers to secure the Web Smart Switch After entering the old password and the new password two times press Apply for the changes to take effect If you forget the password press the Reset button in the front panel of the Switch Note All current settings will be erased when pressing the Reset button Password Setting Old Password New Password Maximum password length is 20 characters and is case sensitive Re type New Password E Figure 30 Password Setting 57 Statistic The Statistic Menu screen will show the
4. n faut Y Disabled S Middle Deen 19 Aut Missle Down u au F Disabled X Mads Down 2 auto Missle Down 05 aut Y Disabled X Missie Down D Aut Mads Down w au Y visabied S Middle Down a aut Moie Down or Aut Disabled Maie Down D aut Missle Down og Auti Disabled e Midde Deen u aut Mads Down aut paed Moie Down Gs vw far let Miate SE sooty RER Disabled Middle Down Figure 17 Port Setting Note The priority of Gigabit Fiber port is higher than Copper Speed The 1000BASE T connections can operate in Forced Mode settings 1000M Full 100M Full 100M Half 10M Full 10M Half Auto or Disable The default setting for all ports are Auto The mini GBIC Gigabit Fiber connections can operate in Forced Mode settings 1000M Full Auto or Disable 28 Flow Control This setting determines whether or not the Switch will be handling flow control Set Flow Control to Enable for avoiding data transfer overflow Or it sets to Disable there is either no flow control or other hardware software management When the port is set to forced mode then the flow control will automatically set to Disable QoS Displays each port s 802 1p QoS priority level for received data packet handling Default setting for all ports is Middle You can change the priority settings in 802 1p Default Priority IEEE 802 1Q VLAN A VLAN is a group of ports that can be anywhere in the network but communicate as though they w
5. ports then apply setting Port n 07 03 04 05 OG OF OG 09 10 1 12 13 14 15 46 img 6 0 0 0 0 00 0 6 6668660 6 m0000000000000000 Net Member O 6 e eeeeooooooeooe Figure 36 Note The multi need server must be support IEEE 802 10 VLAN the sever uplink port is portl 37 Example 4 Setting Tag VLAN on two switches Switch 1 s VLAN 1 2 3 ports have access to the Switch 2 s VLAN 1 2 3 ports The settings of VLAN group for two devices are same Step1 Set Switchl s VLANI port land 4 24 to Not Member then apply setting VID Setting VID 01 VLAN ame VAN Blame should be less than 20 characters Pon 0 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 2 24 f ler 000000 Mot Member O O O ARA Figure 37 Step2 Set Switch2 s VLAN1 member as Switch1 Step3 Uplink two switches via Port 24 38 Trunk Setting The Trunking function enables the cascading of two or more ports for a combined larger bandwidth Up to six Trunk groups may be created each supporting up to 8 ports Add a Trunking Name and select the ports to be trunked together and click Apply to activate the selected Trunking groups Trunk Setting 7 D TrunkingMame HR 03 04 05 OF 07 08 09 10 11 12 13 14 15 16 17 10 19 2 2 22 2 24 m 000000000000000000000000 02 HOOOOOGOGOGODOOGOOGOGEGOI oooooo 03 D D DHDDD DD DDD DDDDDD DD DD D n OOODOOOOOOOOOGOOOGOOOGOOGOOC 05 000000000000000000000 06
6. System Up Time 9 days 4 hours 1 mins 39 seconds E Figure 27 System Information 53 System Setting The System Setting includes IP Information and System information There are two ways for the switch to attain IP Static and DHCP Dynamic Host Configuration Protocol When using static mode the IP Address Subnet Mask and Gateway can be manually configured When using DHCP mode the Switch will first look for a DHCP server to provide it with an IP address network mask and default gateway before using the default or previously entered settings By default the IP setting is static mode with 192 168 0 1 as the IP address By entering a System Name and System Location the device can easily be recognized through the Web Management Utility and in other Web Smart devices on the LAN The Login Timeout controls the idle time out for security purposes when there is no action in the Web based Utility When the Login Timeout expires the Web based Utility requires a re login before using the Utility again 54 System Setting HPinformation Ep zen pe Apply B md a Figure 28 System Setting 55 Trap Setting By configuring the Trap Setting it allows Web Management Utility to monitor specified events on the Web Smart Switch By default Trap Setting is Disabled When the Trap Setting is Enabled enter the Destination IP address of the managing PC that will receive trap information
7. Time 10 25 sec The Max Response Time specifies the maximum allowed time before sending a responding report Adjusting this setting effects the leave latency or the time between the moment the last host leaves a group and when the routing protocol is notified that there are no more members It also allows adjustments for controlling the frequency of IGMP traffic on a subnet Default is 10 seconds Robustness Variable 1 255 The Robustness Variable allows adjustment for the expected packet loss on a subnet If a subnet is expected to be lousy the Robustness Variable may be increased The Robustness Variable cannot be set zero and SHOULD NOT be one Default is 2 times Last Member Query Interval 1 25 sec The Last Member Query Interval is the Max Response Time inserted into Group Specific Queries sent in response to Leave Group messages and is also the amount of time between Group Specific Query messages This value may be adjusted to modify the leave latency of the network A reduced value results in reduced time to detect the loss of the last member of a group Default is I second Host Timeout 130 1225 sec This is the interval after which a learnt host port entry will be purged For each host port learnt a PortPurgeTimer runs for HostPortPurgelnterval This timer will be restarted whenever a report message from host is received over that port If no report messages are received for HostPortPurgelnterval time the learnt
8. in the tag depending on your configuration D De D mis Port Piety D mos o mote Y u R e mode Y a mate Y u m de Y a m de Y m Mode Y o m de Y os Made y e mode Y 40 m ge Y Figure 40 IEEE 802 1p Default Priority Setting 41 Broadcast Storm Control Setting The Broadcast Storm Control feature provides the ability to control the receive rate of broadcasted packets If Enabled default is Disabled threshold settings of 8 000 4 096 000 bytes per second can be assigned Press Apply for the settings to take effect Broadcast Storm Control Setting Broadcast Storm Control y Enabled Disabled Threshold 8 000 bytes per second D 16 000 32 000 64 000 128 000 256 000 512 000 1024 000 2048 000 4096 000 Figure 18 Broadcast Storm Control Setting Jumbo Frame Setting Jumbo Frames enable the transportation of identical data in fewer frames This ensures less overhead lower processing time and fewer interruptions Maximum packet length supported is 10240 bytes Jumbo Frame Setting Disabled Maximum Length is 10240 bytes Apply Figure 19 Jumbo Frame Setting 42 Advanced Setting Find that there are four items including SNMP Setting Spanning Tree Setting 802 3x Setting and IGMP Snooping Setting in Advanced menu SNMP Setting The Web Smart Switch supports SNMP include software referred to as an agent which run
9. monitor and troubleshoot when needed Figure 6 LED indicators Power and System LEDs POWER Power Indicator On When the Power LED lights on the Switch is receiving power Off When the Power turns off or the power cord has improper connection SYSTEM Management Indicator Blinking When the CPU is working the System LED is blinking On Off The CPU is not working 15 1000BASE T Port 1 24 Status LEDs Link ACT Link Activity On When the Link ACT LED lights on the respective port is successfully connected to an Ethernet network Blinking When the Link ACT LED is blinking the port is transmitting or receiving data on the Ethernet network Off No link Speed Green When the Speed LED lights green the respective port is connected to a 1000Mbps Gigabit Ethernet network Amber When the Speed LED lights amber the respective port is connected to a 100Mbps Fast Ethernet network Off When the Speed LED lights off the respective port is connected to a 10Mbps Ethernet network 16 Mini GBIC Port 23 24 Status LEDs Link ACT On When the fiber line connected to the mini GBIC module is installed and connected to a network the Link ACT LED will lights on Blinking When the Link ACT LED is blinking the port is transmitting or receiving data on the Gigabit Ethernet network Off Fiber line or mini GB
10. status of each port packet count Statistics Port ID TxOK RxOK TxError RxError 01 0 0 0 0 02 0 0 0 0 03 6466 1251889 0 0 04 0 0 0 0 05 0 0 0 0 06 0 0 0 0 07 0 0 0 0 08 0 0 0 0 09 0 0 0 0 10 0 0 0 0 11 0 0 0 0 12 0 0 0 0 13 0 0 0 0 14 0 0 0 0 15 0 0 0 0 16 0 0 0 0 17 12256 2577015 0 0 18 0 0 0 0 19 0 0 0 0 20 0 0 0 0 21 0 0 0 0 22 0 0 0 0 23 40 131 0 0 24 0 0 0 0 Figure 31 Statistics Refresh To renew the details collected and displayed Clear Counter To reset the details displayed 58 To view the statistics of individual ports click one of the Port ID as Error Reference source not found Port Statistics Port ID 3 Clear conte Figure 32 Port Statistics Factory Reset The Factory Reset helps you to reset the device back to the default setting from the factory All of the configuration will be reset the IP address of the device will be set to default setting 192 168 0 1 Factory Reset Please be aware that all configuration will reset to default value Factory Reset Figure 33 Factory Reset Backup Setting The backup setting help you to backup the current setting of the Switch Once you need to backup the setting press the Backup button to save the setting To restore a current setting file to the device you must specify the backup file and press Restore button to proceed the setting of the recorded file Backup Setting Please n
11. 10 19 128 Forward Bridge Max Age 6 40 soe 11 9 128 Forward Bridge Hello Time D 10 see gt Bridge Forward Delay 4 30 sec 13 19 128 IE isje U 19 128 Forward Root Port 15 19 128 Forward Root Path Cost 16 19 128 Forward A Ea 17 19 128 Forward 18 19 128 Forward x em e KK 18 19 128 Forward 2 19 128 Forward Port Path Cost 1 65535 Priority 0 255 State a 2 19 128 Forward or 19 128 Forward 2 19 128 Forward 02 19 128 Forward 2 19 128 Forward 0 19 128 Forward 2 19 128 Forward 04 19 128 Pormard lobal Setting Path Cost 1 65535 Pront s 05 19 128 Forward U d riority 0 255 i D D 128 Forward CAMISA Figure 21 Spanning Tree Setting 802 11D Spanning Tree Enable or Disable the 802 11D Spanning function on the Web Smart Switch Bridge Priority This value between 0 and 65535 specifies the priority for forwarding packets the lower the value the higher the priority The default is 32768 45 Bridge Max Age This value may be set to ensure that old information does not endlessly circulate through redundant paths in the network preventing the effective propagation of the new information Set by the Root Bridge this value will aid in determining that the Switch has spanning tree configuration values consistent with other devices on the bridged LAN If the value ages out and a BPDU has still not been received from the Root Bridge the Switch will start sending its own BPDU to all other swit
12. AT TRENDNET S OPTION REPAIR OR REPLACEMENT THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF TRENDNET S PRODUCTS TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF INFORMATION OR DATE OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES AND LIMITS ITS LIABILITY TO REPAIR REPLACEMENT OR REFUND OF T
13. After enabling Asymmetric VLAN by clicking the Apply button users can configure PVID in the following window Figure 29 Step2 Set VLANI port 1 24 to Untag ports then apply setting VID Setting vo 01 Name should be less than 20 characters Seet D a Pot 01 02 0 04 05 06 07 08 09 10 11 12 13 14 15 16 17 1H 19 20 21 22 2 imp 00000060 ORM m000000000000000000000000 EM Not Member 0 00000000000000000000000 mm Figure 30 34 Step3 Create VID 02 and set port 1 5 to Untag ports and port 6 24 to Not Member ports then apply setting Add VID VID 02 VLAN Name vanz Name should be less than 20 characters Port OY 02 03 04 05 06 OF 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 D 24 Sien vw Ge 6 6 6 6 0000000000000000 co EN 000000000000000000000000 HH Wer Menger 000000000000000000000000 KR Figure 31 Step4 Create VIDO3 and set port 1 and 6 9 to Untag ports then apply setting Add VID vo 03 VLAN Name VANG Name should be less than 20 characters Port 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 umg0000000000000000000000 mWOo0o000000000000000000006 Not Member 0 000000000000000000000 KEN EE Figure 32 Step5 Set PVID Port 3 9 PVID value to below list PVID Setting 01 02 03 04 05 06 07 08 09 I 10 at al al al a aL 3 4 u 5 6 17 1922 Carra arr aa Figure 33 35 Note 1 Untag port VLA
14. D D D DDD D D D D D DD D D D D D D D D Ka Note The selected trunk port vetting must be set to the same VLAN Group Figure 38 Trunk Configuration Be sure that the selected trunk setting port must connect to the device with a same VLAN group 39 Mirror Setting Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and or outgoing packet from one port of the Switch to another port where the packet can be studied This enables network managers to better monitor network performances Mirror Setting Mirror Enabled ODinablod Snitter Port om N Source Port Selection Sniffer Mode 01 02 03 04 05 06 OF 08 09 10 11 12 13 14 15 16 17 18 19 2 21 2 23 24 Select All RX eine SCT LG e EG E an an T EG Hao e KA Wen 00000000000000000000000 ER KS Figure 39 Mirror Setting Selection of the Sniffer mode is as follow TX transmit mode this mode will duplicate the data transmit from the source port and forward to the Sniffer port RX receive mode this mode will duplicate the data that send to the source and forward to the Sniffer port Both transmit and receive mode this mode will duplicate both the data transmit from and data that send to the source port then it will forward to the Sniffer port 40 IEEE 802 1p Default Priority This feature displays the status Quality of Service priority levels of each port and for packets that are untagged the switch will assign the priority
15. EEE 802 3z 1000BASE SX LX Gigabit Ethernet Protocol CSMA CD Data Transfer Ethernet 10Mbps half duplex 20Mbps full duplex Rate Fast Ethernet 100Mbps half duplex 200Mbps full duplex Gigabit Ethernet 2000Mbps full duplex Topology Star Network Cables 10BASET 2 pair UTP Cat 3 4 5 up to 100m 100BASE TX 2 pair UTP Cat 5 up to 100m 1000BASE T 4 pair UTP Cat 5 up to 100m Fiber module Mini GBIC Fiber module LC Type Cable Number of Ports 24 x 10 100 1000Mbps Auto MDIX RJ 45 ports 2 x Combo mini GBIC slots Physical and Environmental AC inputs 100 240V AC 50 60 Hz internal universal power supply ku PE 33 Watts Max Temperature Operating 0 40 C Storage 10 70 C Humidity Operating 10 90 Storage 5 90 Dimensions 440 x 210 x 44 mm W x Hx D Certification CE FCC 63 Performance Transmits Method RAM Buffer 512KBytes per device Filtering Address Table MAC Address Learning Packet Filtering 10Mbps Ethernet 14 880 pps Forwarding Rate 100Mbps Fast Ethernet 148 800 pps 1000Mbps Gigabit Ethernet 1 488 000 pps Store and forward 8K entries per device Automatic update 64 Limited Warranty TRENDnet warrants its products against defects in material and workmanship under normal use and service for the following lengths of time from the date of purchase TEG 240WS 5 Years Warranty If a product does not operate a
16. Figure 13 Firmware Upgrade Access Web Double click the device in the Monitor List or select a device in the Monitor List and press this Web Access button to access the device in Web browser DHCP Refresh Press this DHCP Refresh button to refresh IP address of selected device form DHCP server 24 Toolbar The toolbar in the Web Management Utility have four main tabs File View Options and Help In the File TAB there are Monitor Save Monitor Save As Monitor Load and Exit e Monitor Save To record the setting of the Monitor List to the default when you open the Web Management Utility next time it will auto load the default recorded setting e Monitor Save As To record the setting of the Monitor List in appointed filename and file path Monitor Load To manually load the setting file of the Monitor List e Exit To exit the Web Management Utility In the View TAB there are view log and clear log function this function will help you to show trap setting e View Log To show the event of the Web Management Utility and the device e Clear Log to clear the log In the Option TAB there are Refresh Time function this function helps you to refresh the time of monitoring the device Choose 15 secs 30 secs I min 2 min and 5 min to select the time of monitoring In the Help TAB there is About function it will show out the version of the Web Management Utility Configuring the
17. HE PURCHASE PRICE PAID AT TRENDNET S OPTION THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE Governing Law This Limited Warranty shall be governed by the laws of the state of California Note AC DC Power Adapter Cooling Fan Cables and Power Supply carry 1 Year Warranty 66 TRENDnet Product Warranty Registration Please take a moment to register your product online Go to TRENDnet s website at http www trendnet com register TRENDNET 20675 Manhattan Place Torrance CA 90501 USA Copyright 2009 All Rights Reserved TRENDnet
18. IC module is not installed Speed Green When the Speed LED lights green the respective port is connected to a 1000Mbps Gigabit Ethernet network Amber When the Speed LED lights amber the respective port is connected to a 100Mbps Fast Ethernet network Off When the Speed LED lights off the respective port is connected to a 10Mbps Ethernet network 17 CONFIGURATION Through the Web Browser you can configure the Switch such as VLAN Port Trunking Jumbo Frame etc With the attached Web Management Utility you can easily discover all the Web Management Switch assign the IP Address changing the password and upgrading the new firmware Installing the Web Management Utility The following are step by step instructions for installing the Web Management utility 1 Insert the Utility CD in the CD ROM Drive 2 Click Install Utility icon to start TRENDnet Install Utility User s Guide rri Lt Product Registration Exit Figure 7 3 Follow the on screen instructions to install the utility 4 Upon completion go to Program Files gt TRENDnet gt Web Smart Switch Management Utility and open the Web Management utility Figure 8 Web Management Utility The Web Management Utility is divided into four sections Discovery List Monitor List Device Setting and Toolbar function for details instruction follow the below section Discovery List This is the list where you can discover all the We
19. N member can exist in different VLAN groups simultaneously when Asymmetric VLAN function enabled 2 You must create VLAN and add VLAN member first that just can set PVID setting 3 You must change Untag Port PVID to another existent VLAN ID that just can remove Untag port member from VLAN group Tag VLAN Setting The IEEE802 1Q protocol defines a new format of the frame it adds a tag header in the original Ethernet frame as follows IEEE802 1Q Tag VLAN is divided by VLAN ID VID On receiving a frame the switch checks the VID in the tag header of the frame to decide which VLAN it belongs to If the receiving frame doesn t contain the tag header the switch will assign a tag to the frame using the PVID of the port as its VID IEEE 802 1Q Tag Original Ethernet Packet COBRADO Figure 34 36 Example 3 Create two VLAN groups for Tag ports multi need server application setting and two VLAN clients cannot negotiate to each other Asymmetric VLAN function disabled Stepl Set VLANI port I to Tag and port 9 24 to Not Member then apply setting vo 01 VLAN Name VLANL Mame should be less than 20 characters Por 01 02 o3 o4 05 06 OF o8 09 10 11 12 13 14 15 16 17 18 19 20 71 22 23 24 feed mg 090000000000000000000000m wooo0000000000000000000000 m Not Member 00000000000000000000000pm o Figure 35 Step 2 Create VID 02 and set port I to Tag port and port 9 24 to Untag
20. Switch The TEG 240WS 24 Port 10 100 1000Mbps Gigabit Ethernet Web Smart Switch has a Web GUI interface for smart switch configuration 25 The Switch can be configured through the Web Browser A network administrator can manage control and monitor the switch from the local LAN This section indicates how to configure the Switch to enable its smart functions Login Before you configure this device note that when the Web Smart Switch is configured through an Ethernet connection make sure the manager PC must be set on same the IP network For example when the default network address of the default IP address of the Web Smart Switch is 192 168 0 1 then the manager PC should be set at 192 168 0 x where x is a number between 2 and 253 and the default subnet mask is 255 255 255 0 Open Internet Explorer 5 0 or above Web browser Enter IP address http 192 168 0 1 the factory default IP address setting to the address location Address ttp 192 168 0 1 Figure 14 Or through the Web Management Utility you do not need to remember the IP Address select the device shown in the Monitor List of the Web Management Utility to settle the device on the Web Browser When the following dialog page appears remain enter the default password admin and press Login to enter the main configuration window 26 System Name Location Name IP Address 192 168 01 MAC Address 00 11 22 00 11 22 Figure 15 After entering
21. ated Trap IP Shows the IP where the Trap to be sent Subnet Mask Shows the Subnet Mask set of the device Gateway Shows the Gateway set of the device 21 View Trap The Trap function can receive events that occur from the Web Management Switch listed in the Monitor List For information on Trap settings using the Web Management Utility refer to the Trap Setting section in the manual There is a light indicator near the View Trap button A Green light indicates that there has not been any new trap information transmitted A Red light indicates new trap information being transmitted and is set as a reminder to view the trap Figure 9 wem Figure 9 View Trap button When the View Trap button is clicked a Trap Information window will pop out it will show the trap information including the Symbol Time Device IP and the Event occurred Figure 10 The symbol represents the trap signal arise this symbol will disappear after you review and click on the event record Figure 10 Trap Information Note In order to receive Trap information switch has to be configured with Trap IP and Trap Events in Web browser which are available in the Trap Setting Menu see Page 56 for detail Add Item To add a device to the Monitor List manually enter the IP 22 Address of the device that you want to monitor Delete Item To delete the selected device in the Monitor List Device Setting You can set the
22. ault and contains all ports as Untagged 30 IEEE 802 1Q VLAN Setting Asymmetric VLAN Enabled Disabled Apply Note After enabling Asymmetric VLAN by clicking the Apply button users can configure PVID in the following window vip VLAN Name Untag VLAN Ports Tag VLAN Ports EI 01 02 03 04 05 06 07 08 01 default 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Figure 20 802 1Q Asymmetric VLAN Setting Add VID Click to create a new VID group assigning ports I 24 as Untag Tag or Not Member A port can be Untagged in only one VID To save the VID group press Apply vio 01 VLAN Nama VUNE Name should be less than 20 characters Pon 01 02 03 04 05 OG 07 OB 09 10 11 12 13 14 15 16 W 1B 19 2 21 2 aagi Umag G HHR lt Tag C o0o00000000000 EN Mot Member 000000000000000000000 KR eech 153 Figure 21 Add New VID VID A unique VLAN ID VLAN Name A VLAN name is used to associate with the VLAN ID Port The switch port number Untag Outgoing frames without VLAN tag Tag Outgoing frames with VLAN tag Not Member The port number which not to be grouped Select All Select all ports to be VLAN members or not VLAN members Cancel To call the modifications off 31 Apply To activate and save the modifications Delete Click to delete selected VID Asymmetnc VAN Enabled Disatied EN Note Atar enating Asymmatnc VLAN by eted the Apphy button estes can co
23. b management devices in the entire network By pressing the Discover button you can list all the Web Management devices in the discovery list Double click or press the Add to monitor list button to select a device from the Discovery List to the Monitor List 20 System word definitions in the Discovery List MAC Address Shows the device MAC Address IP Address Shows the current IP address of the device Protocol version Shows the version of the Utility protocol Product Name Shows the device product name System Name Shows the appointed device system name DHCP Shows the DHCP status of the device Location Shows where the device is located Trap IP Shows the IP where the Trap to be sent Subnet Mask Shows the Subnet Mask set of the device Gateway Shows the Gateway set of the device Monitor List All the Web Smart Device in the Monitor List can be monitored you can also receive the trap and show the status of the device System word definitions in the Monitor List S Shows the system symbol of the Web Smart device D represent for device system is not alive IP Address Shows the current IP address of the device MAC Address Shows the device MAC Address Protocol version Shows the version of the Utility protocol Product Name Shows the device product name System Name Shows the appointed device system name DHCP Shows the DHCP status of the device Location Shows where the device is loc
24. ches for permission to become the Root Bridge If it turns out that the Switch has the lowest Bridge Identifier it will become the Root Bridge A time interval may be chosen between 6 and 40 seconds The default value is 20 Bridge Hello Time The user may set the time interval between transmissions of configuration messages by the root device thus stating that the Switch is still functioning The default is 2 seconds Bridge Forward Delay This sets the maximum amount of time that the root device will wait before changing states The default is 15 seconds Root Bridge Displays the MAC address of the Root Bridge Root port Displays the root port Root Path Cost Shows the root path cost Path Cost This defines a metric that indicates the relative cost of forwarding packets to specified port list The lower the number the greater the probability the port will be chosen to forward packets The default value is 19 Path Priority Select a value between 0 and 255 to specify the priority for a specified port for forwarding packets the lower the value the higher the priority The default is 128 46 802 1x Setting The IEEE 802 1x provides a security standard for network access control 802 1x holds a network port disconnected until authentication is completed Depending on the results the port is either made available to the user or the user is denied access to the network 802 1X uses the Extensible Authentication Protocol EAP f
25. device by using the function key in the Device Setting Dialog box Configuration Setting In this Configuration Setting you can set the IP Address Subnet Mask Gateway Set Trap to Trap IP Address System name Location and DHCP function Select the device in the Discovery list or Monitor List and press this button then the Configuration Setting window will pop out as Figure 10 after filling up the data that you want to change you must fill up the password and press the Set to process the data changed immediately The default password of this TEG 240WS 24 Port 10 100 1000Mbps Gigabit Ethernet Web Smart Switch configuration is admin Figure 11 Configuration Setting Password Change You can use this Password Change when you need to change the password fill in the password needed in the dialog box and press Set button to proceed the password change immediately 23 Figure 12 Password Change Firmware Upgrade When the device has a new function there will be a new firmware to update the device use this function to update Select the path of where the firmware updated firmware is located by clicking Browse Once you have selected the firmware type the password of the device and click the Start button to proceed Firmware Upgrade Device Information Device IP 192 168 0 1 Device Mac 000055335589 Upgrade Setting Firmware Path Password Upgrade State Start
26. e eee ee 13 eet GEN 13 Rear Panel cuernos Ee kaskede th st TARE asta asses ZON EST 14 Understanding LED Indicators sss sese 15 Power and System LIGA 15 1000BASE T Port 1 24 Status LEDs sees 16 Mini GBIC Port 23 24 Status LED 17 Er ele 19 Installing the Web Management Up 19 Discovery EE deste alae aie eed 20 Monitor List user nt ee ved 21 Device Setting siosar AR 23 KO 25 Configuring the Switch 25 EST 26 KE TTT 27 ege EE 28 IEEE 802 10 KTT 29 Trunk ett eg ane eae 39 Mirror Setting NEEN ENEE adel tabama ehee ee 40 IEEE 802 1 p Default Priority ss sese 41 Broadcast Storm Control Setting sese eee eee eee eee 42 Jumbo Frame Setting priina on E a E 42 Advanced TTT 43 SNMP ea ETT 43 Spanning Tree Setting 45 802 TX EE 47 IGMP Snooping Seng 49 IGMP VLAN Setting NENNEN 51 System SUN AAA 53 System Informaton nono cancrnnnos 53 NA TE 54 A TS gd 56 Password Set eebe 57 St iia 58 Factory Resetear lie te 60 Backup Setting ui 60 A TS a aenor 61 System Rebeet e enge REENEN REENEN 61 NN 62 Technical Specifications rmaenenerenneneree 63 iii ABOUT THIS GUIDE Congratulations on your purchase of the TEG 240WS 24 Port Gigabit Web Smart Switch w 2 Shared Mini GBIC Slots This device integrates 1000Mbps Gigabit Ethernet 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package Purpose This guide discusses how to install your TEG 240WS 24 Port G
27. ed Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised c Mechanical Loading mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading d Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on over current protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern e Reliable Earthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit e g use of power strips K SONSA7 0 2 o s HG user EA amp USTED 4617 gt E Dy RS LTE USA E159561 EA Ver C1 1 00 TABLE OF CONTENT About This Guida EEN dd 1 ere 1 KEE 1 Intfoduetion s sann ania ku jekker 3 Gigabit Ethernet Technology 3 Fast Ethernet Technology 4 Switching Technology ment seren e eee aies 5 VLAN Virtual Local Area Network 6 BO atures unos miras told Ee Ee SES 6 Unpacking and Installation sese 9 Unpacking iii ed 9 Installation ss siecle a 9 Rack Mounting ere deta 10 Connecting Network Cable esse sese 11 IOR OE E E ETET 12 Identifying External Components sees eee eee eee e
28. epl Set VLANI port 9 24 to Not Member then apply setting VID Setting vo 01 VLAN Name vlani Mame should be less than 20 characters Por OF G2 03 os os 06 OF og o9 10 11 121314 15 16 47 HE 19 29 21 nm Zi w0000000000000000000000 0 ol TW000000000000000000000000 HH or Member 0 00000000000000000000000 mm RER Figure 26 Step2 Create VID 02 and set port 9 24 to Untag Port member then apply setting Add VID vo VEAN Mame VLANZ Name should be less than 20 characters Port OF G2 03 ot O o9 10 11 12 13 14 15 16 17 18 19 20 D D 24 SelectAll umag O O O O oeeeeeeeeeeeeeeee ER 190000 00000000000000000 EN Not Member 60000000000000000 EE Pee een Figure 27 33 Example2 802 1Q Asymmetric VLAN settings example Port 1 16 in VLAN 1 port1 5 in VLAN 2 port1 6 9 in VLAN 3 All VLAN1 3 have access to Internet via port 1 IEEE 802 1Q Asymmetric VLAN Setting Asymmetric VLAN Enabled Disabled Ka Note Aker enabling Asymmetne VLAN by c chorg the App buen users can configure PVID n the Kared vdes vo VLAN Name Untag VLAN Porta Tag VLAN Ports D 012 03 04 06 06 07 00 mn van mMMR 97 10 19 20 21 22 23 24 02 va 01 02 03 0405 o e MAG 01 05 07 08 29 o Add mm PVID vettmge Delete Figure 28 Note The multi need server must be support IEEE 802 10 VLAN Stepl Enable Asymmetric VLAN function IEEE 802 1Q Asymmetric VLAN Setting Amymmatnc AN Enabled O Disabled Move
29. ere in the same area VLANs can be easily organized to reflect department groups such as R amp D Marketing usage groups such as e mail or multicast groups multimedia applications such as video conferencing and therefore help to simplify network management by allowing users to move devices to a new VLAN without having to change any physical connections The IEEE 802 1Q VLAN Configuration page provides powerful VID management functions The original settings have the VID as 01 named default and all 24 ports as Untagged Asymmetric VLAN IEEE 802 1Q Asymmetric VLAN default setting is Disabled you can press Enabled radio button and Apply it to submit the 29 Asymmetric VLAN function Asymmatric VLAN OEnabled Disabled Ka Note A er enabling Asymmetne VLAN by releg the Apply button users can configure PVID m the follomng window Untag VLAN Ports 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Figure 18 Enabled Asymmetric VLAN function indows Internet Explorer O The settings of VLAN and Forwarding Table will be reset to default Figure 19 Change setting warning message Note The Settings of VLAN IGMP Snooping and Forwarding Table will be reset to default Untag Asymmetric VLAN Setting The IEEE 802 1Q VLAN Configuration page provides powerful VID management functions The original default VLAN setting has the VID as 01 named def
30. his command affects the behavior of the switch only if periodic re authentication is enabled Default is 3600 802 1x Port Access Control Enable or disable the 802 1x port access on selected port 48 IGMP Snooping Setting With Internet Group Management Protocol IGMP snooping the Web Smart Switch can make intelligent multicast forwarding decisions by examining the contents of each frame s Layer 2 MAC header IGMP snooping can help reduce cluttered traffic on the LAN With IGMP snooping enabled globally the Web Smart Switch will forward IP multicast traffic only to connections that have group members attached IGMP Snooping IGMP Snooping Enabled Disabled Querier State Disabled Query Interval 60 600 sec 125 Max Response Time 10 25 sec 10 Robustness Variable 2 255 2 Last Member Query Interval 1 25 sec 1 Host Timeout 130 153025 sec Router Timeout 60 600 sec 260 Leave Time 0 25 sec 1 Figure 23 IGMP Global Setting IGMP Snooping Enable or Disable the IGMP Snooping function on the Web Smart Switch Querier State Enable or Disable the Querier State of IGMP Snooping 49 Query Interval 60 600 sec The Query Interval is the interval between General Queries sent By adjusting the Query Interval the number of IGMP messages can increase or decrease larger values cause IGMP Queries to be sent less often Default is 125 seconds Max Response
31. host entry will be purged from the multicast group Default is 260 seconds 50 Router Timeout 60 600 sec This is the interval after which a learnt router port entry will be purged For each router port learnt a RouterPortPurgeTimer runs for RouterPortPurgelnterval This timer will be restarted whenever a router control message is received over that port If no router control messages are received for RouterPortPurgelnterval time the learnt router port entry will be purged Default is 125 seconds Leave Timer 0 25 sec This is the interval after which a Leave message is forwarded on a port When a leave message from a host for a group is received a group specific query is sent to the port on which the leave message is received A timer is started with a time interval equal to IgsLeaveProcessInterval If a report message is received before above timer expires the Leave message is dropped Otherwise the Leave message is either forwarded to the port Default is 1 second IGMP VLAN Setting To enable IGMP snooping for a given VLAN select Enable under State then press the Edit button under Static Router Port Setting then select the ports to be assigned for IGMP snooping for the VLAN and press Apply for changes to take effect The VLAN Setting of IGMP snooping VLAN Router Ports ID VLAN Name State Setting Multicast Entry Table 01 default Enabled Y Ed Figure 24 VLAN Setting of IGMP Snooping 51 Router P
32. igabit Web Smart Switch w 2 Shared Mini GBIC Slots Terms Usage In this guide the term Switch first letter upper case refers to your TEG 240WS 24 Port Gigabit Web Smart Switch w 2 Shared Mini GBIC Slots and switch first letter lower case refers to other Ethernet switches INTRODUCTION This chapter describes the features of the TEG 240WS 24 Port Gigabit Web Smart Switch w 2 Shared Mini GBIC Slots and some background information about Ethernet Fast Ethernet Gigabit Ethernet switching technology Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802 3 Ethernet utilizing the same packet structure format and support for CSMA CD protocol full duplex flow control and management objects but with a tenfold increase in theoretical throughput over 100 Mbps Fast Ethernet and a hundredfold increase over 10 Mbps Ethernet Since it is compatible with all 10 Mbps and 100 Mbps Ethernet environments Gigabit Ethernet provides a straightforward upgrade without wasting a company s existing investment in hardware software and trained personnel The increased speed and extra bandwidth offered by Gigabit Ethernet is essential to coping with the network bottlenecks that frequently develop as computers and their busses get faster and more users use applications that generate more traffic Upgrading key components such as your backbone and servers to Gigabit Ethernet can greatly improve network response times a
33. ill maintaining the same network cabling and adapter cards Switching LAN technology is a marked improvement over the previous generation of network bridges which were characterized by higher latencies Routers have also been used to segment local area networks but the cost of a router the setup and maintenance required make routers relatively impractical Today switches are an ideal solution to most kinds of local area network congestion problems VLAN Virtual Local Area Network A VLAN is a group of end stations that are not constrained by their physical location and can communicate as if a common broadcast domain a LAN The primary utility of using VLAN is to reduce latency and need for routers using faster switching instead Other VLAN utility includes Security Security is increased with the reduction of opportunity in eavesdropping on a broadcast network because data will be switched to only those confidential users within the VLAN Cost Reduction VLANs can be used to create multiple broadcast domains thus eliminating the need of expensive routers Features 24x 1000BASE T Auto negotiation Gigabit Ethernet ports 2x Combo mini GBIC Auto Sense for optional mini GBIC transceiver to extend distance share with 2 1000BASE T ports AH 1000BASE T ports support auto MDI MDIX so there is no need to use cross over cables or an up link port Half duplex transfer mode for connection speed 10Mbps and 100Mbps Full duplex
34. nfigure PVD lt the evrd window vo VLAN Name Untag VLAN Ports Tag VLAN Ports 01 02 03 04 05 06 07 08 L 09 10 11 12 13 14 15 16 97 18 19 20 21 2223 28 a Sales v8 19 202221 24 Figure 22 Delete VID To change exist IEEE 802 1Q VLAN setting press the VID to modify that IEEE 802 1Q VLAN setting IEEE 802 1Q VLAN Setting VAN OEnabied ODinabied Mote Abr enabing Asymmatne VLAN by cred the App butten users can conique PVO n the feliceng wnsow vio VLAN Name Untag VLAN Ports Tog VLAN Ports D 8199 01 04 89 04 07 08 DI dele 09 10 11 42 13 14 45 46 17 18 192021222324 L Sales 18 198202223 24 a Figure 23 Modify VID PVID settings While receiving an untagged frame from the port the switch will assign a tag to the frame using the PVID of the port as its VID PVID Setting Port 01 02 03 04 05 06 07 evo 0 JC JO JD 1 Pot 13 14 15 17 16 19 evio Jaap H Figure 24 PVID Setting 32 Example 1 Here is an example of two VLAN groups with several ports in each group and VLAN 1 VID 01 does not have communication with VLAN 2 VID 02 IEEE 802 1Q VLAN Setting Armens VAN OEnatied Daea Note Ain eeatling Asymmetric VLAN by clicking the Apply button users can configure PVID in the followng window vio VLAN Name Uatag VLAN Ports Tag VLAN Ports D L WLAD 01 02 0304 05 06 07 08 vwe RSE o Figure 25 St
35. ons to retrieve and modify MIB objects Default setting private Trap Setting Enable or Disable the Trap function on the Web Smart Switch Traps are messages that alert network personnel of events that occur on the Switch Such events can be as serious as a reboot someone accidentally turned the Switch OFF or less serious events such as a port status change The Switch can generate traps and send them to the trap recipient i e network administrator Trap Name Enter a Trap Name i e Trap Name must be selected from a Community Name IP Enter the IP of the device to be monitored and choose the event s to trap Event The available trap Events to choose from include System Device Bootup Fiber Link Up Link Down Fiber Abnormal Receive Error Fiber Abnormal Transmit Error Twisted Pair Link Up Link Down Twisted Pair Abnormal Receive Error Twisted Pair Abnormal Transmit Error 44 Spanning Tree Setting The Web Smart Switch supports IEEE 802 1D Spanning Tree Protocol STP implementation is designed to prevent network loops that could cause a broadcast storm When the physical links forming a loop provide redundancy only a single path will be forwarding frames If the link fails STP activates a redundant link automatically 802 1D Spanning Tree Setting Di 9 128 Forward Spanning Tree Global Setting 08 19 128 Forward 802 10 Spanning Tree OEsabled Daabled m3 19 128 Forwerd Bridge Priority 0 65535 sec
36. or passing authentication messages gt R 5 CH TRENDNET Gigabit Web Smart Switch 802 1x Setting Enable OErabied Datei Figure 22 802 1x Setting Enable Enable or Disable the 802 11x function on the Web Smart Switch Radius Server IP Enter the IP address of the Radius Server 47 Authentication Port Sets primary port for security monitoring Default is 1812 Key Confirm Key Masked password matching the Radius Server Key TxPeriod Sets the number of seconds that the switch waits for a response to an EAP request identity frame from the client before retransmitting the request Default is 24 seconds ReAuthEnabled This Enable or Disable the periodic ReAuthentication control When the 802 1X function is Enabled the ReAuthEnabled function is by default also Enabled QuietPeriod Sets the number of seconds that the switch remains in the quiet state following a failed authentication exchange with the client Default 80 seconds SuppTimeout Sets the switch to client retransmission time for the EAP request frame Default is 12 seconds ServerTimeout Sets the amount of time the switch waits for a response from the client before resending the response to the authentication server Default is 16 seconds MaxReq This parameter specifies the maximum number of times that the switch retransmits an EAP Request packet to the client before it times out the authentication session Default is 5 times ReAuthPeriod T
37. orts Settings VLANID 1 VLAN Nome dde id ic Router 04 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 10 19 20 21 2 2 U fa WE a JE a NE ea UEI ea OPE EEE ENE EE EEE ENE ENTEN EN E jt __ _ 01 02 03 04 05 06 07 08 03 10 11 12 13 14 15 16 17 18 19 20 21 22 D 24 KO Figure 25 IGMP Router Port Setting To view the Multicast Entry Table for a given VLAN press the View button Multicast Entry Table VLAN VLAN Multicast Port Group ID ID N G Multicast MAC address Memt 001 1 default 239 255 255 100 01 00 5e 7f ff 64 01 02 03 17 Figure 26 IGMP Multicast Entry Table Setting 52 System Setting Find that there are nine items including System Information System Setting Trap Setting Password Setting Statistics Factory Reset Backup Setting Firmware Upload and System Reboot in System menu System Information Press on System Information to display the system information status on this screen it will show the Product Name Firmware Version Protocol Version MAC Address System Name Location Name IP Address Subnet Mask Default Gateway Trap IP Login Timeout and System Up Time r System Information Product Name Firmware Version Protocol Version TEG 240WS 3 01 04 2 001 003 MAC Address 00 00 55 34 45 fe System Name Location Name IP Address 172 21 82 22 Subnet Mask 255 255 240 0 Default Gateway 172 21 80 254 Trap IP 0 0 0 0 Login Timeout 5 minutes
38. ote that the device will reboot after a successful configuration restore Backup current Back setting to file Restore saved _Browse setting from file Restore Figure 34 Backup Setting Note when restoring a recorded file the current password will not be erased Firmware Upload The Firmware Upload helps you backup or upload firmware from to the Switch Once you need to backup the current firmware of the Switch press the Backup button to save the current firmware of the Switch To restore or upgrade firmware to the Switch you must specify the firmware file and press Upload button to proceed the firmware upload Firmware Upgrade Backup Firmware ime Sg Upload Firmware eee Figure 35 Firmware Upload System Reboot Provides to a safe way to reboot the system ensure the configuration has been saved or all the changes you just made may be lost after system reboot System Reboot System Reboot Figure 36 System Reboot Logout When pressed you will logout of the web configuration page and will return to the first Login page System Name Location Name JP Address 192 168 01 MAC Address 00 11 22 00 11 22 D roves MENE Figure 37 62 TECHNICAL SPECIFICATIONS Standards IEEE 802 3 10BASE T Ethernet IEEE 802 3u 100BASE TX Fast Ethernet IEEE 802 3ab 1000BASE T Gigabit Ethernet IEEE 802 3x Full Duplex Flow Control I
39. ps Gigabit Ethernet that runs in Auto negotiation mode and 10Mbps Ethernet or 100Mbps Fast Ethernet that runs both in half and full duplex mode and 1000Mbps Gigabit Ethernet runs in full duplex mode using four pairs of Category 5 cable These 1000BASE T ports are Auto MDI type port The Switch can auto transform to MDI II or MDI X type so you can just make an easy connection that without worrying if you are using a standard or crossover twisted pair cable There are additional 2 ports combo mini GBIC slot for optional mini GBIC module 11 AC Power The Switch used the AC power supply 100 240V AC 50 60 Hz The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan The switch s power supply will adjust to the local power source automatically and may be turned on without having any or all LAN segment cables connected 12 IDENTIFYING EXTERNAL COMPONENTS This chapter describes the front panel rear panel and LED indicators of the Switch Front Panel The figure below shows the front panels of the Switch Figure 4 Front panel LED Indicators Comprehensive LED indicators display the status of the switch and the network see the LED Indicators chapter below 1000BASE T Gigabit Ethernet Ports Port 1 24 The Switch twenty four Gigabit twisted pair ports supported auto negotiable 10 100 1000Mbps and auto MDI MDIX crossover detection function this function gives true
40. s locally on the device A defined set of variables managed objects is maintained by the SNMP agent and used to manage the device These objects are defined in a Management Information Base MIB which provides a standard presentation of the information controlled by the on board SNMP agent SNMP defines both the format of the MIB specifications and the protocol used to access this information over the network 3 SNMP Setting SNMP Setting Enable Enabled Disabled Community Setting Access Access Right Community Name Read Only Road Virte Enable Enabled Disabled Event System Device Bootup Fiber Link Up Leik Down Fiber Abnormal Ri o Fiber Abnormal Transmit Error Twisted Pair Link Up Link Down Twnsted Par Abnormal Rec Eror Twasted Par Abnormal Transma Error Figure 20 SNMP Setting 43 SNMP Setting Enable or Disable the SNMP function on the Web Smart Switch Community Setting In support of SNMP version 1 the Web Smart Switch accomplishes user authentication by using Community Settings that function as passwords The remote user SNMP application and the Switch SNMP must use the same community string SNMP packets from a station that are not authenticated are ignored dropped Read_Only The community with read only privilege allows authorized management stations to retrieve MIB objects Default public Read_Write The community with read write privilege allows authorized management stati
41. s warranted above during the applicable warranty period TRENDnet shall at its option and expense repair the defective product or deliver to customer an equivalent product to replace the defective item All products that are replaced will become the property of TRENDnet Replacement products may be new or reconditioned TRENDnet shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to TRENDnet pursuant to any warranty There are no user serviceable parts inside the product Do not remove or attempt to service the product through any unauthorized service center This warranty is voided if i the product has been modified or repaired by any unauthorized service center ii the product was subject to accident abuse or improper use iii the product was subject to conditions more severe than those specified in the manual Warranty service may be obtained by contacting TRENDnet office within the applicable warranty period for a Return Material Authorization RMA number accompanied by a copy of the dated proof of the purchase Products returned to TRENDnet must be pre authorized by TRENDnet with RMA number marked on the outside of the package and sent prepaid insured and packaged appropriately for safe shipment WARRANTIES EXCLUSIVE IF THE TRENDNET PRODUCT DOES NOT 65 OPERATE AS WARRANTED ABOVE THE CUSTOMER S SOLE REMEDY SHALL BE
42. s well as significantly speed up the traffic between your subnets Gigabit Ethernet enables fast optical fiber connections to support video conferencing complex imaging and similar data intensive applications Likewise since data transfers occur 10 times faster than Fast Ethernet servers outfitted with Gigabit Ethernet NIC s are able to perform 10 times the number of operations in the same amount of time In addition the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost effective method to take advantage of today and tomorrow s rapidly improving switching and routing internetworking technologies And with expected advances in the coming years in silicon technology and digital signal processing that will enable Gigabit Ethernet to eventually operate over unshielded twisted pair UTP cabling outfitting your network with a powerful 1000 Mbps capable backbone server connection creates a flexible foundation for the next generation of network technology products Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need for high performance networks A number of high speed LAN technologies have been proposed to provide greater bandwidth and improve client server response times Among them 100BASE T Fast Ethernet provides a non disruptive smooth evolution from the current 10BASE T technology The non disruptive and smooth evolution nat
43. the password the main page comes up the screen will display the device status TRENDNET Gigabit Web Smart Switch TEG 240WS System Information Product Name TEG 240W5 Firmware Version 30104 Protocol Version 2 001 003 MAC Address 00 00 55 34 4540 System Namo Location Namo IP Address 172218272 Subnet Mask 255 255 240 0 Default Gateway 172 21 20 254 Trap 0000 Login Timeout minutes System Up Time 6 days hours 8 mens 15 seconds Figure 16 System Information Setup Setting Find that there are seven items including Port Setting IEEE 802 1Q VLAN Settings Trunk Setting Mirror Setting IEEE 802 1p Default Priority Broadcast Strom Control Setting Jumbo Frame Setting in 27 Setup menu Port Settings In Port Settings menu Figure 17 this page will show each port s status selected drop down menu to set each port s Speed and QoS priority then press Apply button to activate changes To refresh the information table to view the latest port setting and Link Status press the Refresh button The Link Status in the screen will show the connection speed and duplex mode else this dialog box will show Down when the port is disconnected 12 auti Made Down B Aut Middle Down VI Aut Middle Deen E y TA TT Se 15 Austi Middle Deen Port ID Speed ass Link Status w aut Maz Down D Aut m Disabled Y Middle Deen ET Missie 1000M Fu az A Disabled Y Nadie Down 18 Aut Mads Down
44. transfer mode for connection speed of 10Mbps 100Mbps and 1000Mbps Store and Forward switching scheme capability to support rate adaptation and ensure data integrity Upto 8K unicast addresses entities per device self learning and table aging 512 KBytes packet buffer F HHHHHHHH HHH Supports IEEE 802 3x flow control for full duplex mode ports Supports IEEE 802 1Q VLAN Supports IEEE 802 1p Priority Queues Supports Static Port Trunk Supports IGMP Snooping Supports SNMP for RFC1213 MIB II and Private MIB Supports IEEE 802 1D Spanning Tree Supports 802 1x port based access control Supports Jumbo Frame Supports Broadcast Storm Control Supports Port Mirroring Supports Port Setting for Speed Flow control Easy configuration via WEB Browser Easy setting via Web Management Utility Standard 19 Rack mount size UNPACKING AND INSTALLATION This chapter provides unpacking and installation information for the Switch Unpacking Open the shipping cartons of the Switch and carefully unpacks its contents The carton should contain the following items TEG 240WS 24 Port Gigabit Web Smart Switch wi 2 Shared Mini GBIC Slots Multi Language Quick Installation Guide Y CD COM Utility amp User s Guide Power Cord Rack Mount Kit Rubber Feet Screws and Mounting Brackets If any item is found missing or damaged please contact your local reseller for replacement Installation The site where you install the h
45. ub stack may greatly affect its performance When installing consider the following pointers Install the Switch in a fairly cool and dry place See Technical Specifications for the acceptable temperature and humidity operating ranges Install the Switch in a site free from strong electromagnetic field generators such as motors vibration dust and direct exposure to sunlight Leave at least 10cm of space at the front and rear of the hub for ventilation Install the Switch on a sturdy level surface that can support its weight or in an EJA standard size equipment rack For information on rack installation see the next section Rack Mounting When installing the Switch on a level surface attach the rubber feet to the bottom of each device The rubber feet cushion the hub and protect the hub case from scratching Figure 1 Attach the adhesive rubber pads to the bottom Rack Mounting The switch can be mounted in an EIA standard size 19 inch rack which can be placed in a wiring closet with other equipment Attach the mounting brackets at the switch s front panel one on each side and secure them with the provided screws Figure 2 Combine the Switch with the provided screws 10 Then use screws provided with the equipment rack to mount each switch in the rack o o o o o o o o a a ON o o o o o o o Figure 3 Mount the Switch in the rack Connecting Network Cable The Switch supports 1000Mb
46. ure and the dominating potential market base virtually guarantees cost effective and high performance Fast Ethernet solutions 100Mbps Fast Ethernet is a standard specified by the IEEE 802 3 LAN committee It is an extension of the 10Mbps Ethernet standard with the ability to transmit and receive data at 100Mbps while maintaining the CSMA CD Ethernet protocol Since the 100Mbps Fast Ethernet is compatible with all other 10Mbps Ethernet environments it provides a straightforward upgrade and takes advantage of the existing investment in hardware software and personnel training Switching Technology Another approach to pushing beyond the limits of Ethernet technology is the development of switching technology A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments Switching is a cost effective way of increasing the total network capacity available to users on a local area network A switch increases capacity and decreases network loading by dividing a local area network into different segments which don t compete with each other for network transmission capacity The switch acts as a high speed selective bridge between the individual segments The switch without interfering with any other segments automatically forwards traffic that needs to go from one segment to another By doing this the total network capacity is multiplied while st
Download Pdf Manuals
Related Search