TP-Link TD-8610 User's Manual
Contents
1. TD 8610 TD 8610B External ADSL2 MODEM 1910010011 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2008 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT Fe This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or reloc2. name and its password is admin if you want to change it please go to Management Password Figure 3 5 TP Link TD 8610 Set Password Device Info WAN Setup LAN Setup Management Diagnose Password Upgrade admin Figure 3 5 3 3 Setup 1 Choose Configuration See Figure 3 6 2 Enter the VPI VCI value which is provided by your ISP click Save to finish the configuration You can press Next to add VPI VCI value TD 8610 8610B External ADSL MODEM ADSL MODEM TP Link TD 8610 Device Info Modify VPI VCI Settings WAN Setup ADSL Modulation 1 8 ATM PVCs VPI Mar LAN Setup 0 Management 1 33 0 35 0 100 e 81 0 200 0 0 Back Apply Next Save Reset Figure 3 6 3 4 Software Dial TD 8610 TD 8610B works in bridged RFC 1483 Bridged mode to connect to the Internet You need to install dial software on your PC There is some software working on WINDOWS in market example for EnterNet3000 RASPPPoE and WinPeET TD 8610 8610B External ADSL MODEM ADSL MODEM Appendix A Default Configuration USER NAME admin PASSWORD admin IP ADDRESS 192 168 1 1 VPI VCI 0 32 1 33 0 35 0 100 0 200 8 35 8 81
3. 1 Product Overview 1 4 Product main specification 1 2 Supporting protocol 1 3 Transmit data rate 1 4 1 5 System support 1 6 Working environment 1 7 Electric parameter Chapter 2 Hardware Installation Guide 2 1 System requirement 2 2 LED explanation 2 3 Rear panel 2 4 Hardware installation procedures Chapter3 How to use 3 1 Computer Configuration 3 2 Login 3 3 Setup 3 4 Software Dial ATM property nette s Et eth Ee Pre tv c d ER ETE TD 8610 8610B External ADSL MODEM ADSL MODEM Chapter 1 Product Overview With the excellent design of circuit and high quality production we guarantee ADSL2 MODEM a high performance very good stability and easy to use TD 8610 TD 8610B is a complete plug and play solution With standard Ethernet interface it can be directly connected to any 10M 100M Ethernet devices support Auto MDIX TD 8610 TD 8610B not only use html web mode through Ethernet port to configure the MODEM but also use external utility software too You can download it from our website http www tp link com 1 1 Product main specification High speed and asymmetry data transmit mode adapt to wide band internet access Point to point connection provide safe and exclusive bandwidth Support All ADSL industrial standards Advanced DMT modulation and demodulation Firmware upgradeable Compatible with all mainstream DSLAM CO Real time Configuration and device monitoring ON WV Quick res
4. ate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Mark Warning This class product In domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Package Contents The following contents should be found in your package One TD 8610 TD 8610B External ADSL2 MODEM One AC power Adapter for TD 8610 TD 8610B External ADSL2 MODEM One RJ45 cable Two RJ11 cable One ADSL splitter only available for TD 8610 One Resource CD for TD 8610 TD 8610B External ADSL2 MODEM including This User Guide Other Helpful Information V V cg Note Make sure that the package contains the above items If any of the listed items are damaged or missing please contact with your distributor CONTENTS Chapter
5. outer to reboot LAN Connect with your computer s NIC LINE WAN Connect to the MODEM of Splitter or connect to the telephone line 2 4 Hardware installation procedures First Step Connect the MODEM of Splitter with the LINE port of the TD 8610 TD 8610B ADSL2 MODEM by telephone line While you need to use a telephone please attach telephone line into the phone of Splitter Second Step Connect category 5 cable with RJ45 jacks to ADSL MODEM s LAN port and your computer s NIC Third Step Link power adapter into the power jack of ADSL MODEM Please note the range of voltage of power adapter should be within AC 220 230V 50Hz which will make the MODEM under normal operation Last Step Check the line connection to see if everything is ready Then power up TD 8610 8610B 0 B eon PHONE LINE RJ45 MODEM ADSL SPLI e LINE RJ11 ADSL LINE AC POWER ADAPTER ISP Figure 2 1 TD 8610 8610B External ADSL MODEM ADSL MODEM Chapter 3 How to use 3 1 Computer Configuration 1 Connect the cable according to Chapter 2 and then turn on the power 2 Change the IP address of your PC Figure 3 1 Open TCP IP Properties of the LAN card in your PC enter the IP address as 192 168 1 is any value between 2 to 254 Subnet mask is 255 255 255 0 Gateway is 192 168 1 1 DNS address is the value provided by ISP Internet Protocol TCP IP Prope
6. ponse semi conductive surge protect circuit provides reliable ESD surge protect function 1 2 Supporting protocol G 992 1 G dmt Annex A B G 992 2 G lite Annex A B ANSI T1 413 G 992 3 ADSL2 Annex A B compliant G 992 5 ADSL2 Annex A B compliant ADSL dual latency fast path and interleaved path 1 432 ATM physical layer compliant Supports RFC2516 PPPoE Supports RFC1483 EoA Bridged cg Note Need third party software 1 3 Transmit data rate Max download data rate 24Mbps TD 8610 8610B External ADSL MODEM ADSL MODEM gt gt upload data rate 1 Mbps gt Maxline length 6Km 1 4 ATM property gt AAL5 OAM RM and raw cell types supported Direct hardware support for 4 Receive VCs with additional RX VCs and TX VCs supported in software gt Full 24 bit Virtual Path Identifier VPI and Virtual Circuit Identifier VCI 1 5 System support Support PVC Support IEEE 802 3 IEEE 802 3u Support 10Base T 100BASE TX full duplex or half duplex Ethernet Support Auto MDIX V ON 1 6 Working environment gt Operating temperature 0 40 gt Storage temperature 40 C 70 C gt Humidity 10 9096 1 7 Electric parameter gt Adaptor power Output 9VAC 0 8A 50Hz or 60 Hz Power consumption 4W Maximum TD 8610 8610B External ADSL MODEM ADSL MODEM Chapter 2 Hardware Installation Guide 2 1 System re
7. quirement Confirm your computer has been installed with networking interface card NIC before connecting ADSL MODEM to your computer with operating system supporting the TCP IP protocol 2 2 LED explanation TD 8610 External ADSL2 Modem The panel of ADSL MODEM includes one power button one power indicator RED and four function indicators GREEN and these five indicators are explained as chart 1 1 Name Status Indication On Power OK Power Off Power fail On There is data transmitting or receiving on WAN Act port Off No data transmitting or receiving on WAN port On There is a mistake when ADSL is transmitting Alarm data or receiving data Off ADSL normal Slow flash Self detecting when power up ADSL Quick flash The LINE port is sending or receiving ADSL data On The LINE port has connected to ISP s network Off The LINE port is disconnected On LAN port is normal LAN Off Connection on LAN port is abnormal Flash Data is transmitting or receiving on LAN port Chart 1 1 TD 8610 8610B 2 3 gt Turn on off the ADSL modem s power gt Power 9VAC 0 8A input please do not use any unknown power adaptor otherwise may cause damage to your ADSL MODEM RESET reset default When the device is working please press the reset button of the Modem keep the reset button pressed down for more than five seconds and then wait for the r
8. rties xi General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 168 Subnet mask 255 255 255 0 255 255 Default gateway 132 168 1 1 92 168 gt Ubtain ONS server address automatically Use the following DNS server addresses Preferred DNS server 202 96 128 133 Alternate DNS server 202 96 128 188 Advanced Cancel Figure 3 1 cg Note 1 The users of Windows 98 can open TCP IP Properties according to the following Right press Mouse Network Neighbor gt Choose Properties gt Double press TCP IP PCI Fast Ethernet Adapter 2 The users of Windows 2000 NT XP can do the following Right press Network Neighbor gt TD 8610 8610B External ADSL MODEM ADSL MODEM Choose Properties gt Right click Local Connection gt Choose Properties gt Double press Internet Protocol TCP IP 3 The words in fact maybe are different with this guide You can check whether your configuration is successful through PING command Enter Ping 192 168 1 1 If the screen likes the following your configuration is successful Pinging 192 168 1 1 with 32 bytes of data from 192 168 1 1 bytes 32 time ims TTL 254 from 192 168 1 1 bytes 32
9. time ims TTL 254 from 192 168 1 1 bytes 32 time ims TTL 254 from 192 168 1 1 bytes 32 time ims TTL 254 Ping statistics for 192 168 1 1 Packets Sent 4 Received 4 Lost loss Approximate round trip times in milli seconds Minimum ms Maximum ims Average ms Figure 3 2 If the screen likes the following your configuration is unsuccessful Please repeat the previous steps again gt Documents and Settings Administrator ping 192 168 1 1 inging 192 168 1 1 with 32 bytes of data equest timed out equest timed out equest timed out equest timed out ing statistics for 192 168 1 1 Packets Sent 4 Received Lost 4 loss gt Figure 3 3 3 2 Login Startup Internet Explorer and enter 192 168 1 1 then enter user name admin password admin you will see the page Figure 3 4 When ADSL connection is OK you will see some information such as link rate TD 8610 8610B External ADSL MODEM ADSL MODEM TP Link TD 8610 Device Info Version jBn19h8 d16m WAN Setup Firmware LAN Setup Hardware Serial Number Management address 01 00 01 ADSL Statistics Status Idle Channel Mode Downstream Upstream Rate Kbps SNR Margin dB Attenuation dB Super Frames Super Frame Errors Figure 3 4 The default user
Download Pdf Manuals
Related Search