Tekkeon MP3400 User's Manual
Contents
1. as required Please ensure the cable is unplugged from the portable device while Center Negative changing the voltage Symbol Verify that a battery is installed in the portable device as some devices will not function without a battery installed Verify if your device is designed with charging circuitry that limits the input voltage If so myPower ALL may not be able to power or charge the device For example if a device is designed to accept only a 10 2V input then myPower ALL may not be able to power or charge the device myPower 10 all Limited Warranty The product enclosed herein is warranted to be free of operational defects for a period of one year from the date of purchase In the event of a defect in operation during the warranty period Tekkeon Inc will replace the defective product when the owner returns all product contents The limited warranty will be considered void if the unit is tampered with subject to misuse negligence or accidental damage has been improperly serviced or if the security seal is removed This warranty is limited to replacement only and shall not cover any other damages Any product returned to Tekkeon Inc with no fault found will be returned to the owner at the owner s expense To obtain warranty coverage please complete and submit the enclosed registration card Disclaimer of Warranties Any user of this product does so at the user s own risk To the maximum extent permitted by appl2. L continue to charge the battery until the battery capacity indicates FULL 5 When the battery capacity indicates FULL unplug the power adapter NOTE myPower ALL will automatically shut down the power input when fully charged so you can charge it overnight USER GUIDE 3 Using myPower ALL myPower ALL can be used to power and or charge your portable device With devices that require higher voltage levels like notebook computers and portable DVD players we recommend that you use myPower ALL only to power the device You will find that powering without charging your higher voltage device will maximize the battery life of myPower ALL thus letting you use your portable device even longer To use myPower ALL to power and or charge your device take these steps which are described in detail in the following sections e Select an adapter plug and connect the plug to the output cord Connect the power output cord to myPower ALL Adjust the voltage level to match that of your device and lock the voltage setting Connect the adapter plug output cord to your device Select Connect the Adapter Plug 1 Select the adapter plug that fits securely into the power jack on your portable device 2 Locate the polarity symbol on your device in the area around the power connector jack oco Occo Center Positive Center Negative myPower ALL supports Center Positive polarity only If your device has a Center Negative polarity do not pow
3. Tekkeon my 7 Universal Rechargeable Battery MP3300 MP3400 User Guide my Power USER GUIDE Contents vene 2 Getting Started oerte trt RR Laie 2 Unpacking myPower ALL sse 2 Getting to Know myPower 3 Charging my Power t rn et tee 3 Using myPowel All u a 4 Select Connect the Adapter 02 222 020 2 4 Connect the Power Output Cord 5 Adjust the Voltage 5 Connect the Portable Device 8 View myPower ALL Battery Capacity 8 Recording Device Information sene 9 Obtaining Adapters sss nes 9 Troubleshooting oraret eret et ree erede 10 Limited Warranty ertet reci eee eiecti 11 Customer SUDDpOFL cet ett tbe tice 12 Overview You can use myPower ALL the universal rechargeable battery to power just about any portable device Simply connect myPower ALL to your portable DVD player notebook computer digital camera digital camcorder portable CD player PDA mobile phone or other portable device to extend the battery life As an added bonus myPower ALL will charge the internal battery on some devices while also powering the device myPower ALL goes where you go Slip the handy leather case onto your belt or just toss myPo
4. er the device with myPower ALL contact support tekkeon com for assistance 200097 3 Connect the adapter plug to the power output cord but not the device If you are using a UA xxx adapter rather than PA xxx you must insert the L34 adapter that came with your myPower ALL between the adapter cord and UA xxx adapter as shown L34 Adapter for cord is connected to myPower ALL the voltage setting M Pad Will reset to the lowest voltage 3V for MP3300 5V for MP3400 which is the default voltage setting If you change the adapter plug while the power adapter Connect the Power Output Cord 1 Plug the large end of the power output cord into the DC OUT jack on the end of myPower ALL The 3V MP3300 or 5V MP3400 voltage indicator will turn on to indicate that the voltage is set to the lowest setting If you have previously selected a voltage the voltage selection will be returned to the lowest setting Adjust the Voltage Level 1 Locate the voltage specification for your portable device This can be found on the device power adapter label or device specification label which typically is found on the bottom of the unit If available use the voltage specification shown on the power adapter Sample Power Adapter Label USER GUIDE 9 2 With the voltage lock in the unlocked position switched right to VOLTAGE set the voltage output to the voltage selection that is equal to or one increment h
5. ff At this point you must charge myPower ALL 1 With the voltage lock in the locked position LOCK and the adapter plug power output cord or the power adapter connected press and hold the voltage selector When you release the voltage selector the battery capacity indicators will turn off and one indicator will turn on to indicate the voltage Selection 200097 8 all CAPACITY INDICATOR Red Indicator 1 5 Recharge before using 1st Green Indicator 5 15 2nd Green Indicator 15 25 3rd Green Indicator 25 40 4th Green Indicator 40 55 5th Green Indicator 55 70 6th Green Indicator 70 85 7th Green Indicator 85 100 Recording Device Information The Device At A Glance Card included with myPower ALL enables you to record the information you need to use myPower ALL with each of your portable devices Simply record the device name required voltage and reference letter for the compatible adapter Store the card in the pocket provided inside the leather case Obtaining Adapters Eight adapter plugs that fit most DG adapter jacks on a variety of portable devices are included with myPower ALL If none of these plugs fits snugly into your portable device power jack please go to our web site at www tekkeon com mpadapters to determine which adapter plug you need for your device You can obtain most adapters through the web site or by contacting Tekkeon by phone at 888 787 5888 or 1 714 832 1266 If avai
6. icable law Tekkeon Inc and its suppliers provide the hardware and any support services related thereto as is and with all faults and hereby disclaim all warranties and conditions whether express implied or statutory including but not limited to implied warranties of merchantability fitness for a particular purpose non infringement lack of negligence or correspondence to description except for those warranties specifically and expressly provided in the Limited Warranty With respect to the use of this product in no event shall the company be liable for any loss of profit or any other commercial damage including but not limited to special incidental consequential and other damages USER GUIDE 11 Customer Support Gustomer support for myPower ALL is available at Tekkeon Inc c o myPower ALL 3002 Dow Avenue 134 Tustin CA 92780 888 787 5888 714 832 1266 www tekkeon com Tekkeon Inc must issue a Return Merchandise Authorization RMA number for all exchanges or refunds www tekkeon com my 200097 12 Tekkeon www tekkeon com 2007 Tekkeon Inc Rev B All Rights Reserved myPower is a trademark of Tekkeon Inc Cut loose Stay loose
7. igher than the voltage identified for your device To do this press the voltage selector until the voltage indicator turns on under the appropriate voltage selection 3 4 5 5 6 7 5 9 12 14 for MP3300 and 5 6 7 5 9 12 14 16 19 for MP3400 For example if your device requires 6V set the voltage to 6 If your device requires 7 2V set the voltage to 7 5 It is important to set the voltage selector NO MORE than one step higher than the voltage requirement for the portable device as an incorrect setting may prevent myPower ALL from working with your device or may harm your device in the rare instance that the device accepts the higher voltage However for all devices adjusting the voltage ONLY one step higher than required will not harm the device The following table provides recommended voltage settings by device type myPower ALL VOLTAGE SELECTION Device Type Voltage on Device Suggested Voltage on Power Adapter myPower ALL 14V 12V 16V 14V 19V 14 16V 24V 19V Portable DVD Players 9v 7 5 9V Notebook Computers 12V 9 12V Digital Cameras 5 6V 5 6V CD Players 4 5 5V 5V PDAs 5V 5V Mobile Phones 3 7 5V 5V 9V 75 9V 12V 9 12V MP3 MP4 5V 5V 2777727 Camcorders 3 Slide the voltage lock to the locked position switched left to LOCK This will prevent you from accidentally selecting a different voltage while your device is connected 4 To change the voltage slide the vo
8. lable through Tekkeon the adapter will be sent to you for a nominal fee USER GUIDE 9 Troubleshooting If myPower ALL does not power the portable device or charge the device battery take these steps Verify that the current consumption of the portable device is not more than 3 5 Amp 3 5 Amp for both MP3300 and MP3400 If the device consumes more than the maximum provided by myPower ALL the device will shut down when turned on and cannot be powered and or charged by myPower ALL Verify that the device does not require more than 14V MP3300 or 19V MP3400 If the device requires more MP3300 MP3400 will not be able to charge the device However in most but not all cases MP3300 MP3400 will be able to power the device View the remaining battery capacity If it is below 25 recharge myPower ALL Check that the output cord is connected to both myPower ALL and the portable device and that the adapter plug fits snugly into the power jack on your portable device If not try another adapter Verify that the polarity of the device power jack is Center Positive If the polarity is Center Negative please contact support tekkeon com for assistance Center Positive Check that the output voltage for your portable device matches or Symbol is just below the output voltage set on myPower ALL If the output voltage is not correct unlock the voltage lock if in the locked position and change COE the voltage
9. ltage lock to the unlocked position VOLTAGE and select a new voltage Be sure to relock the voltage TIP You can optimize the use of myPower ALL with your notebook computer or portable DVD player by setting the voltage on myPower ALL to less than the required voltage shown on the notebook computer power supply This prevents myPower ALL from charging the device thus extending the amount of time you can use myPower ALL to power your notebook computer Most notebook computers have a battery voltage of 11 1V or 14 8V allowing them to be powered with 12V or 14V Therefore it is recommended that you set the voltage to 12V first and then test to see if it will power your notebook If not increase the voltage to 14V and retest For MP3400 repeat this process until you reach the voltage that will power your notebook Even though myPower ALL MP3300 provides only up to 14V it may be used to power notebooks To determine if MP3300 can power your notebook verify that the total output power provided by the device power adapter is not more than 64W To do this multiply the voltage by the amps shown on the power adapter Watt Voltage x Amps If the output power is greater than 64W myPower ALL will not power or charge the device If it is less than 64W set the voltage on MP3300 to 12V and test to see if it will power your notebook at this setting If not increase the voltage to 14V and retest Most portable DVD players require 9 or 12 volts Set the
10. voltage to 7 5V and test to see if myPower ALL will power your device at this setting If not increase the voltage by one level and retest USER GUIDE 1 Gonnect the Portable Device 1 Connect the adapter plug into the power jack on the portable device 2 Turn on the portable device and use it as you would normally While connected myPower ALL will power and charge your device As mentioned earlier myPower ALL will not charge a device if the voltage setting is lower than that required or Leave the portable device turned off and myPower ALL will charge the device battery 3 When finished unplug the power output cord from myPower ALL and your device NOTE If your portable device displays a low voltage low capacity or double beep warning while myPower ALL is connected adjust the voltage setting to one level higher TIP For most portable devices myPower ALL can be used to power the device even when the device battery is not installed View myPower ALL Battery Capacity The capacity in myPower ALL will decrease as the battery powers and or charges your devices The remaining voltage is shown on the voltage indicator which is accessed as described on page 9 As the voltage decreases the lights will turn off in sequence from right to left When the myPower ALL battery capacity is low only the red EMPTY light will be on You should recharge myPower ALL at this time When myPower ALL is completely out of battery all lights will be o
11. wer ALL into your briefcase or backpack it s that lightweight Getting Started Unpacking myPower ALL Your myPower ALL package includes the following mL myPower ALL lithium polymer User guide not shown recnargeanig etter Leather travel case Power adapter Power output cord Device At A Glance with belt loop Gard Adapter plug kit with drawstring bag 8 adapter tips my 200097 Getting to Know myPower ALL Voltage Indicators Capacity Indicators Voltage Selector Voltage Lock Charging Indicator DC OUT For connection to device DC IN For connection to power adapter Charging myPower ALL myPower ALL will charge in four hours when completely empty The green CHARGE indicator will turn on after the battery is 8096 charged Therefore you should view the actual battery capacity before disconnecting the power adapter to stop charging Before using myPower ALL for the first time you must charge the device for four hours 1 Plug the power adapter into the DC IN jack on the end of myPower ALL 2 Remove the output cord from the DC OUT jack if connected 3 Plug the power adapter into a wall outlet The red CHARGE indicator will turn on to indicate the battery is charging and is less than 80 charged 4 When the green CHARGE indicator turns on set the voltage lock to LOCK and press the voltage selector to view the battery capacity If the capacity does not indicate FUL
Download Pdf Manuals
Related Search