Home
TechniSat VC 2002 S User's Manual
Contents
1. VC 2002 S INSTALLATION AND OPERATION Satellite Receiver TechniSat VC 2002 S Stereo TechniSat Satellitenfernsehprodukte GmbH TechnicPark Postfach 560 W 5568 Daun Germany TechniSat VC 2002 S INSTRUCTION MANUAL FOR THE TECHNISAT VC 2002 S SAFETY INSTRUCTIONS In the interests of safety please read and observe the following instructions before using your new VC 2002 S This sheet and the following pages concerning installation and operation should be retained for future reference INSTALLATION The procedures set out on page 5 should be fol lowed carefully NOTE Always connect the LNB before connecting to the mains supply Failure to do this may cause damage to the appliance Ventilation Vents on the top and side panels are provided for necessary ventilation The appliance should not be placed in a position where the free pas sage of air would be severely restricted In addi tion for the same reasons as above the VC 2002 S should not be placed on a soft base Water and moisture Ensure that the appliance does not come into contact with any dampness or moisture RISK OF ELECTRIC SHOCK and or damage to the VC 2002 S Heat Do not install the VC 2002 S in the immediate proximity of a heat source radiator oven etc CARE AND USE Power source Connect the VC 2002 S to a power supply which matches the requirements of the appliance 240 V 50 Hz Safe connecti
2. PROGRAMMING Itis possible to alter each channel or change the preset completely if you so wish Switch to the channel you would like to alter and enter the video amp audio frequencies polarisation bandwidth and decoder mode if necessary as follows POLARISATION Select the required polari sation vertical or horizontal by pressing the V H button on the remote control VIDEO TUNING After pressing either the up and down tuning key a 3 figure number is sho wn on the display frequency in MHz To alter the frequency you have the option of either pres sing the up and down tuning keys or the requi red frequency can be keyed in directly using the remote control Although you must always ent er a 4 digit number for the frequency ie 0950 2050 only the last 3 digits are displayed DEV SELECTION ASTRA channels are pre programmed Hi high video level Other chan nels can be programmed Lo low video level AUDIO TUNING a First press either the Mono Stereo button to select 0 Mono 0 0 for Stereo b If stereo is selected the button A B should be pressed to obtain A left or B right side audio outputs c The correct frequency can be set using the audio up down keys After selecting A or B the required frequency can be keyed in directly and will be shown on the digital display d Tune audio bandwidth I wide ll narrow by pressing the W N button IF STEREO HAS BEEN SELECTED IT IS NECESSARY TO REPEAT STAGES
3. the preprogrammed TV and radio stations This table also contains information on the stored audio video parameters which will give you a guide if you wish to change the preset If you are not satisfied with the preprogramming or if you want to add some channels you can programme the receiver to your own require ments as described in the section on Individu al Programming see below i Using V H LNB The TechniSat VC 2002 S is preprogrammed in accordance with programme table 1 at the end of this manual ii Using ISISAT LNB refer to programme table 2 If the ISISAST Preprogramming is called up the preprogramming for V H LNBs does not meet the table any more and all programmes for V H LNB need to be programmed again 1 Switch the receiver to Standby mode power off 2 Press both the up and down channel buttons simultaneously for approx 3 seconds The display will indicate SEL select 3 You can now select a channel Channel up PRG 1 Normal programme Channel down PRG 2 ISISAT programme 4 Switch on the receiver power on PREPROGRAMMING IS NOW COMPLETED CHANNEL SELECTION The channel number selected is shown on the digital display ie F01 F99 or C01 C99 Channels preceded with an F are stored channels and can be accessed eit her directly using the up and down keys or by keying in the respective channel number Non stored channels can only be accessed by key ing in the channel number INDIVIDUAL
4. MHz A B WIDTH PHASIS LEVEL VIDEO MODE SATION KHz External Sky Sports Ver Screensport Hor EUROSPORT Ver 10 MTV Hor 11 LIFESTYLE Hor 12 CHILDR CH Hor 1 KY MOVIES PLUS 1 436 7 02 7 20 SIER 150 J1 Hngn NOR D 4 ver 2 Movie Channel Ver 3 _SKYM GOLD Adult Ch 1 597 7 02 7 20 STER 150 J17 High NOR D 4 Ver 4 SKY ONE Ver 5 SKY NEWS Ver 6 CNN Ver 7 8 9 13 Child Ch MONO Ver 14 JSTV STER Ver 15_ FILMNET D2 MAC MONO Hor 16 RTL 4 VERONIQUE 1 391 7 02 7 20 STER Hor 17_RTL PLUS 1 229 6 50 7 02 MONO Ver 18 SAT 1 Ver 19 PRO7 Ver 20 TELE 5 Hor 21 ARD 1 PLUS Hor 22 3SAT Ver 23 NORD 3 Hor 24 PREMIERE STER Hor 25 TELECLUB 1 832 6 50 7 02 MONO Hor 26 TV3 Schwed 1 244 6 50 7 02 MONO Hor 27 TV 1000 Hor 28 UK GOLD Hor 29 TV 3 Daenemark Hor 30 Hor 31 TV 3 Norw Hor 32 1 686 6 50 7 02 MONO 280 50us High NOR D 4 Ver 43 72 free IF AUDIO MHz BAND DE EM VIDEO DECODER DECODER POLARI MHz A B WIDTH PHASIS LEVEL VIDEO MODE SATION KHz External 3 Hit Radio alle D 4 Ver 74 Holland FM 150 High NOR D 4 Ver 75 Radio Super Gold 150 High NOR D 4 Ver 76 Giant FM 150 High NOR D 4 Ver NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR NOR D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 77 RTL Radio NL STER 78 Rad Schwed Int 79 Schweizer Rad Int 80 Sunrise Radio 81 RTL Radio D STER 82 DE
5. RD 1 PLUS 06 3 SAT 07 NORD 3 08 SPORTKANAL 0964 7 027 20 MONO HIGH 09 EUROSPORT 1559 7 207 02 MONO HIGH 10 MTV STER HIGH 11 PREMIERE 1214 7 027 20 STER HIGH 12 SKY ONE STER HIGH 13 SKY NEWS 14 RTL 4 VERONIQUE 15 LIFESTYLE CHILD 16 SES VIDEO 17 NORDS3 18 19 TELECLUB 20 FILMNET 21 22 JSTV 23 24 CNN 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 1186 16 50 7 02 MONO 1280 50us NOR D 4 HIGH 43 88 free IF AUDIO MHz MODE BAND DE EM DECODER DECODER VIDEO MHz A B WIDTH PHASIS VIDEO MODE LEVEL KHz External 89 SWF 3 90_ POWER FM 91 OPUS RADIO 92 RADIO LUX INT 93 SKY RADIO 94 STAR SAT RADIO 95 DTSCH WELLE Il 96 DTSCH WELLE 97 DEUTSCHLANDF II 98 DEUTSCHLANDF 99 RADIOROPA INFO PS The first IF have been calculated on the basis of the following data 1 For the frequency range 10 95 11 7 GHz LOF 10 000 GHz 2 For the frequency range 11 7 12 5 GHz LOF 10 750 GHz 3 For the frequency range 12 5 12 75 GHz LOF 11 475 GHz LOF Local Oscillator Frequency 12
6. UTSCHLANDF III 83 DEUTSCHLANDF II 84 DEUTSCHLANDF STER 85 DTSCH WELLE II 86 DTSCH WELLE 87 NDR2 STER 88 SWF3 STER 89 STAR SAT RADIO STER 90 OPUS RADIO STER 91 Solar Radio 92 POWER FM STER 93 RADIO LUX INT STER 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High 150 High Hor Ver Hor Ver Hor Ver Ver Ver Ver Ver Hor Hor Ver Hor Ver Hor Hor 94 ASDA FM 150 High NOR D 4 Ver 95 Quality Europe FM STER 150 High NOR D 4 Ver 96 CNN Radio 150 High NOR D 4 Ver 97 Hit Radio 1 318 7 74 7 92 STER 150 High NOR D 4 Ver OT O 74 U 98 SKY RADIO 1 318 7 38 7 56 99 RADIOROPA INFO 1 406 7 74 7 92 PS The first IF have been calculated on the basis of the following data 1 For the frequency range 10 95 11 7 GHz LOF 10 000 GHz 150 High NOR D 4 Ver 150 J17 High NOR D 4 Ver 2 For the frequency range 11 7 12 5 GHz LOF 10 750 GHz 3 For the frequency range 12 5 12 75 GHz LOF 11 475 GHz o ojo z zjojzzjo zz zo aaa IE O OlOmOOmOO Omooo DD Z Z Z ZIZ ZIZ Zz Z Z ZIZ zZ m E oO O O O O O OJO JO O O O only with external Decoder LOF Local Oscillator Frequency ASTRA TV ASTRA RADIO PROGRAMME TABLE 2 ISISAT LNB IF AUDIO MHz MODE BAND DE EM DECODER DECODER VIDEO MHz A B WIDTH PHASIS VIDEO MODE LEVEL KHz External 01 PRO7 02 RTL PLUS 03_ SAT 04 TELES 05_ A
7. b AND c FOR THE OTHER FREQUENCY NOTE i Holding down the AUDIO and TUNING buttons accelerates the frequency change li 5 seconds is allowed for keying in the frequencies directly If this is not achieved ie entry does not appear on the display press the appropriate TUNING or AUDIO key and re enter STORING Once you have attained the best possible picture and sound quality you can sto re the channel by using for example a ball point pen to press the sunken STORE button for 1 2 seconds ERASING To erase stored information press and hold down the ERASE key as above Now the erased channel can only be selected by ente ring the number via the key pad of the remote control see also CHANNEL SELECTION TechniSat VC 2002 S PROGRAMMING Watching a scrambled Videocrypt programme 1 Select a coded channel eg Movie Channel or Sky Movies Plus 2 Insert the viewing card as indicated by the arrow 3 After a few seconds the descrambled picture will appear on the screen NOTE Do not bend or damage the card in any way SCREEN MESSAGES Please insert card make sure that the card is inserted correctly Please wait descrambled picture should appear in a few seconds Your card is invalid ensure the card is ins erted correctly and or has not been damaged Your card has expired a replacement card is required Channel blocked indicates there is some thing wrong with your card In the case o
8. f the last 3 messages first of all try turning the receiver off disconnect from the mains and leave for one minute Turn on again and retry card If this still fails contact BSkyB CONNECTING A SEPARATE DECODER To choose between normal and decoder mode press DECODER In position n the reception signal will be connec ted directly from the TV or video recorder In position d the coded signal non Videocrypt coded channels is sent from the scart socket to the decoder The decoded signal is sent back to the receiver and can be picked up at the scart socket or at the UHF output connection Press the D MODE button to select the deco der signal according to the following table D1 Flat MAC compatible signal D2 PAL de emphasised baseband signal D3 Unclamped video signal D4 Clamped video signal Be sure to consider the recommendation of the manufacturer regarding the connection of the decoder DOES NOT APPLY TO VIDEOCRYPT INTER NAL DECODER BUT REFERS TO THE USE OF A SEPARATE DECODER FOR NON VIDEOCRYPT CODED CHANNELS FREQUENCY SHIFT If the LNB of the outdoor unit does not supply the exact IF frequency it is possible to change it as follows 1 Press the V H button for about 3 seconds The receiver displays AFC Enter 999 The receiver displays 0 0 Now it can be tuned up or down 5 MHz with the tuning buttons Once you have achieved the best picture quality
9. ges Connecting a separate decoder Frequency Shift Specifications Trouble Shooting Programme Table 1 V H LNB Programme Table 2 ISISAT LNB 3 10 11 12 TechniSat VC 2002 S TechniSat APPLIANCE DESCRIPTION FRONT PANEL FOF mew TechniSat VC 2002 S Digital Display STANDBY LED Decoder Card Slot AUTHORIZE BUTTON Channel Up Down Keys Press this button if you wish to see a Pay per View programme BACK PANEL AUDIO OUTPUTSUR LNB IF IN UHF CHANNEL ADJUSTMENT PRESET TO 36 UHF OUT LNB PWR OUT PAL I EUROSCART FOR VCR REC EUROSCART FOR TV 5 5 W MAX m PAL B G TSG 30 WATTS MAX vipeo M VIDEO OUTPUT SCART CONNECTION FOR TV ITSG VIDEO SWITCH ANT IN DECODER OUTPUT SCART CONNECTION MODULATOR SWITCH FOR DECODER VCR PALI PALG TechniSat VC 2002 S LL REMOTE CONTROL ol eN e AUDIO UP DOWN FOR SUBCARRIER pa E FREQUENCY 5 0 8 80 MHz MONOISTEREO AB LEFTIRIGHT STEREO USED WITH AUDIO UPIDOWN DE EMPHASIS WIDE TV SOUND NARROW RADIO VH POLARISATION ccr er em Emm DECODER NORMALIDECODER MODE l CHANNEL UP DOWN VIDEO FREQUENCY UP DOWN 950 2050 MHZ DECODER SIGNAL SELECTION D1 D4 TechniSat INSTALLATION amp INITIAL OPERATION 1 Connect the receiver VC 2002 S to the LNB of 4 i If you are using a scart cable connection switch the outdoor unit using a coaxial cable via IF IN your TV to AV connecti
10. on ii If UHF cable connections are being used it is necessary to find a suitable UHF channel The CAUTION Always ensure that the mains supply satellite receiver is preprogrammed to channel is off when making any connections including LNB 36 To set the TV or VCR to this channel select connection TSGon the receiver back panel and search on the TV until two vertical white bars are clearly 2 The connection between receiver and TV is visible If due to interference it is necessary to made using a scart cable Alternatively you can adjust the UHF channel this can be done using make the connection using an antenna cable the channel adjustment switch on the back of the receiver by turning the screw 3 Connect the receiver to the mains supply 240 V 50 Hz TechniSat VC 2002 S Installation possibilities 1 Connection to TV external decoder if N required Receiver o ie U UHF OUT o 5 5 W MAX L ANT IN 30warts MAX DECODER VIDEO nn nn nn nn nn u mm m Scart Decoder 2 Connection to TV VCR LNB N Receiver uH our ANT IN sowarts MAX LNB PWR OUT 5 5 W MAX DECODER VIDEO EUROSCART FOR VCR REC EUROSC FOR VCR REC 3 Connection to TV VCR LNB N Receiver O unr out ANT IN sowarts MAX EUROSCART FOR VCR REC DECODER VIDEO TechniSat VC 2002 S PREPROGRAMMING At the end of this manual you will find a list of all
11. on to the mains The mains leads should be routed so that they are not likely to be walked on or pinched by items placed against them When not in use If the VC 2002 S is left unattended or unused for long periods of time be sure to unplug the mains connector Unplug the VC 2002 S from the mains when the mains lead or mains connector is damaged the VC 2002 S has been exposed to rain or water a solid object or liquid substance has entered the appliance via the air vents there is a noticeable change in the performance of the VC 2002 S the appliance is not operating as normal the VC 2002 S has been dropped or the outer casing has been damaged NOTE Servicing and repairs must only be carried out by trained service staff Accessories and replacement parts Both accessories and replacement parts should only be purchased as recommended by your satellite dealer Be sure to consult your dealer in all aspects concerning equipment purchase servicing and repairs Cleaning Disconnect the VC 2002 S from the mains befo re cleaning Use a damp cloth only Do not use liquid or aerosol cleaners TechniSat VC 2002 S CONTENTS Safety Instructions Appliance Description Installation amp Initial Operation Preprogramming Channel selection Individual Programming Polarisation Video Tuning DEV Selection Audio Tuning Storing Erasing Programming Watching a scrambled Videocrypt programme Screen Messa
12. or lights is connected to an appropriate AC power supply 2 Power switch is off Press power button 3 Fuse has blown Replace No picture or sound but 1 TV is not not set to the right channel indicator lights are lit or fine tuning on TV is incorrectly adjusted Check that TV is tuned to appropriate UHF channel when using modulator output 2 Antenna is not pointed at a satellite Check that antenna is aligned to an operating satellite 3 Bad cable connections Check all cable connections and connectors 4 Defective LNB Replace Indicator lights are lit Internal fuse has blown except stand by Contact dealer Picture has sparkles or 1 Antenna is not aligned to an operating is grainy satellite Readjust antenna 2 Video fine tuning incorrectly adjusted Readjust accordingly 3 Excessive signal loss between LNB and recei ver Install a line amplifier 4 LNB is defective Replace 5 Bad connections Check all coaxial connections and plugs 6 Water in coaxial cable Dry out if necessary and use suitable connector sealant on all outside connections Audio sounds distorted 1 Selected AUDIO is not tuned to correct subcarrier Check the required audio frequency with the programme table Remote control does not operate 1 Weak battery in remote control Replace or has poor range 10 ASTRA TV ASTRA RADIO PROGRAMME TABLE 1 V H LNB IF AUDIO MHz MODE BAND DE EM VIDEO DECODER DECODER POLARI
13. you can store the frequency shift with the STORE button C1 AOON O NOTE The frequency shift applies for all channels TechniSat VC 2002 S SPECIFICATIONS 1 Tuner Input Frequency Input Impedance Input Level Input Connector LNB Power Bandwidth Gain Control Tuning 2 Clamped Video De Emphasis Bandwidth Output Level Output Connector 3 Decoder Output Mode Output Level Output Connector Output Impedance 4 Audio Frequency Range Mode Bandwidth De Emphasis Frequency Response Output Level Output Connector 5 RF Modulator UHF UHF Output Level UHF Output Connector Ant Input Connector 6 Others Supply Voltage 950 2050 MHz 75 Ohm 70 dBm to 25 dBm F type 18 V constant at 300 mA max 14 V 18 V for V H LNB 26 MHz AGC PLL frequency synthesized CCIR REC 405 1 625 LINE 5 MHz 1 V p p Scart and RCA phono 4 different modes D1 D4 1 V p p Scart and RCA phono L R 75 Ohm 5 0 to 8 8 MHz adjustable Mono Stereo selectable 150 KHz 280 KHz selectable 50 us J17 20 Hz to 15 kHz 2 V p p Scart and RCA phono L R 30 39 tunable preset to 36 switchable PAL PAL B 75 4 dBuV IEC Male IEC Female 240 Volt 50 Hz Technical specifications are subject to improvements TechniSat VC 2002 S LL TROUBLE SHOOTING PROBLEM CAUSE SOLUTION No picture or sound no 1 No power Make certain that your VC 2002 S indicat
Download Pdf Manuals
Related Search
Related Contents
サニタリエースSD取扱説明書 SafeVIEW - Farnell creative Voici la procédure afin de pouvoir de choisir PC banking pour la File 1 Copyright © All rights reserved.
Failed to retrieve file