Stiga VILLA 8211-3013-10 User's Manual
Contents
1. STIGA VILLA STIGA 8211 3013 10 MOWING AHEAD Denna produkt eller delar d rav omfattas av f ljande m nsterskydd This product or part of it is covered by the following design registration Sverige Sweden 62 435 ENGLISH SYMBOLS The following symbols are displayed on the ma chine in order to remind you about the safety pre cautions and attention necessary when using the machine The symbols mean Warning Read the instruction book and safety man ual before using the machine Warning Do not put hands or feet under the cover of A the machine when it is running Iy A Of 2 Warning Beware of objects being flung out Keep spectators away Warning Before starting any repair work remove the spark plug cable from the spark plug INTRODUCTION The power outlet s tension roller and tension arm s spring on the base machine are available in two ver sions figs 1 and 2 NOTE To be able to fit this mower deck Multi clip mod 85M version B is required VERSION A Standard on models made between 1982 83 If the base machine is fitted with version A a sepa rate assembly set is required to be able to fit the mower deck Assembly set art No 13 1967 11 The set contains a v belt tension roller spring as sembly components and assembly instructions N B Older base machines2. Tighten the bearing box s fixing bolts M turning the mower deck over and turn ing the blades that it has been fitted correctly NOTE The mower deck should be dismantled from the base ma When the drive belt is fitted check by chine 8 Now refit the mower deck on the base machine CHANGING BLADES Use protective gloves to prevent cuts 4h when changing blades blade tips Make sure the blades are always sharp This gives the best mowing results Always check the blade s after an impact If the blade system has been damaged the defective parts must be changed Always use original spare parts Using A non original spare parts can result in the risk of damage even if they fit in the machine The cutting system consists of two blade bars each with two interchangeable blade tips Y fig 11 Both blade tips should be replaced at the same time to avoid any imbalance Fit the new blade tips Tighten the screws V and W fully Tightening torque V 9 8 Nm W 24 Nm And heavy impact can result in the blade tip being folded aside Loosen the locking nut X and turn the blade tip back to its correct position Mount a new shear bolt V Tighten the lock nuts X and Z SPARE PARTS STIGA original spare parts and accessories are constructed exclusively for STIGA machines Note that non original spare parts and accessories have not been checked or approved by STIGA Usage of such parts and accessories can A influence t
3. can however be fitted with version B if they have previously been adapted for use with a Multiclip mower deck VERSION B Standard on machines made from 1994 The mower deck can be fitted directly ASSEMBLY MOWER DECK 1 Remove both mounting bolts D on the base ma chine fig 3 2 Insert both spacer sleeves E in the mower deck s arms fig 4 The spacer sleeves are supplied in a plastic bag 3 Bolt the mower deck to the base machine 4 Pull the v belt onto the mower deck s pulley This is carried out easier if the height adjustment lever is in position 5 5 Make sure that the tension roller J is on the out side of the v belt figs 2 and 5 6 Hook the spring into the bracket G figs 2 and 5 7 Screw the guard H in position using three screws fig 6 The screws are supplied in the plastic bag 8 Hook the chain I and lifting spring F in the attach ment s lift arm fig 6 SETTING For the mower deck to mow evenly and cleanly it needs to be adjusted correctly 1 Make sure the tyre pressure is correct Front 0 4 bar 6 psi Rear 1 2 bar 17 psi 2 Place the machine on a flat surface Loosen the screws K fig 7 3 Adjust the mower deck so that the casing s front and rear edges are the same height from the floor 4 Tighten the screws USE MOWING HEIGHT The mower deck has 17 fixed mowing heights from 30 mm to 80 mm N B The stated mowing heights apply when the
4. he machines operability and safety STIGA cannot be held responsi ble for injuries caused by these prod ucts STIGA reserves the right to make changes in the prod uct without prior notice
5. machine is standing on firm ground MOWING ADVICE For the best Multiclip effect follow this advice mow regularly use full throttle on the engine ENGLISH keep the underside of the mower deck clean use sharp blades donot mow wet grass mow twice using different mowing heights if the grass is long MAINTENANCE mower deck unless the engine has been stopped the ignition key has been removed the spark plug cap has been removed from the spark plug the parking brake is engaged the mower deck is disengaged CLEANING After use rinse off the underside of the mower deck using a garden hose No service action must be taken on the If grass cuttings have dried on to the attachment dismantle the mower deck and scrape clean the un derside If necessary touch up the underside using a suita ble paint to prevent corrosion CHANGING THE DRIVE BELT 1 Remove the mower deck from the base machine 2 Remove the transmission casing 3 Loosen the tension arm L fig 8 4 Loosen the right hand bearing box s fixing bolts M fig 9 5 Fit the new drive belt the blades are square 90 to each oth er See figure 10 If you fit the drive belt incorrectly the blades will hit each oth er resulting in the blades being dam aged The new drive belt must be fitted so that 6 The belt is tensioned by pushing the tension arm L forwards and then securing in position 7
Download Pdf Manuals
Related Search