SOYO SY-V6BE+ User's Manual
Contents
1. Power On by Keyboard function 1 23 Important When using the Power On by Keyboard function please make sure the ATX power supply can take at least take 720mA load on the 5V standby lead 5VSB to meet the standard ATX specification Apart from the jumper setting you have to enter the CMOS setup and set the Power On by Keyboard item in the SOYO COMBO Setup to Password or function key Step7 Clear CMOS Data J P5 Clear the CMOS memory by momentarily shorting pin 2 3 on jumper P5 for atleast5 seconds and then by shorting pin 1 2 to retain new settings This jumper can be easily identified by its white colored cap CMOS Clearing Clear CMOS Data Retain CMOS Data Short pin 2 3 for Short pin 1 2 JP5 Setting _ at least 5 seconds to retain the to clear the CMOS 1 2 3 newsettings 1 2 3 Note You must unplug the ATX power cable from the ATX power connector when performing the CMOS Clear operation setting twice after clearing CMOS data If you fail to do this EN You MUST enter the CMOS SETUP and SAVE CMOS gt your new setting would NOT be Saved Hardware Installation SY V6BE Quick Start Guide 5 Note on Over clocking Capability The SY V6BE mainboard provides over clocking capability Due to the over clocking setting your system may fail to boot up or hang during run time If this occurs please perform the following steps to recover your system from the abnorm2. 3322 Web Site http www soyo com tw E mail info mail soyo com tw USA Branch Office Soyo Tek Inc USA Tel 408 452 7696 Fax 408 573 7696 Web Site http Avww soyousa com E mail sales soyousa com SOYO Europe Soyo Europe B V Holland Tel 31 79 3637500 Fax 31 79 3637575 Web Site http www soyo europe com http www soyo nl E mail Sales soyo nl Germany Branch Office SAAT Technology GmbH Germany Tel 49 0 444 204044 Fax 49 0 444 203422 Web Sites http www saatde http www soyo saatde http www soyo saatcom Email sales saatde UK Branch Office Soyo U K Ltd Tel 44 0 181 569 4111 Fax 44 0 181 569 4134 Web Site http www soyo nl E mail sales soyo nl Japan Branch Office Soyo Computer J apan Tel 81 3 33682188 Fax 81 3 33682199 Web Site http www soyo co jp E mail soyo po iijnet or jp Hong Kong Branch Office Soyo Hong Kong Ltd H K Tel 852 2710 9810 Fax 852 2710 9078 Web Site http www soyo com hk E mail rshu hkstar com
3. SDRAM module Computer case and chassis with adequate power supply unit Monitor PS 2 Keyboard Pointing Device PS 2 mouse VGA Card Sound Card optional Speaker s optional Disk Drives HDD CD ROM Floppy drive Extemal Peripherals Printer Plotter and Modem optional LAR A e aE ae aE SE a AE A E i Intemal P eripherals Modem and LAN cards optional 5 Hardware Installation SY V6BE Quick Start Guide Install the Mainboard Follow the steps below in order to perform the installation of your new SY V6BE Mainboard Step 1 Install the CPU M Mark your CPU Frequency Record the working frequency of your CPU that should be clearly marked on the CPU cover L 233MHz 66 x 3 5 J 300MHz 66 x 4 5 CJ 350MHz 100x 35 J 450MHz 100x 45 L 266MIHz 66 x 4 0 J 333MHz 66 x5 0 LJ 400MHz 100 x 4 0 J 500MHz 100 x 5 0 CPU Mount Procedure To mountthe Pentium II processor that you have purchased separately follow these instructions 1 Unpack the Retention Kit Position the Mainboard 3_ Insert the Screws 4 Install the Supporting Base C ATX Power Slot 1 CPUFAN Power Heat Sink Larger Pinhole Insert the Latches Odd Tunguag Remember to connect the CPU Cooling Fan to the C
4. Supports onboard hardware monitoring 500MHz amp Celeron processors 266 and includes Hardware Doctor utility 400MHz optional gt Auto detect CPU voltage gt S1 x 32 bit AGP slot gt PC98 ACPI Ultra DMA 33MHz gt 4x 32 bit bus mastering PCI slots gt Power on by modem alarm or keyboard gt 2xUSB ports onboard F Suppors Wake Or LAN WOL 2 IDA pon upports Wake On LAN WOL gt Supports multiple boot function gt DMI utility SY V6BE Quick Start Guide 2 Installation Ur NON To avoid damage to your mainboard follow these simple rules while lt gt handling this equipment Before handling the mainboard ground yourself by grasping an unpainted portion of the system s metal chassis Remove the mainboard from its anti static packaging Hold it by the edges and avoid touching its components Check the mainboard for damage If any chip appears loose press carefully to seat it firmly in its socket Follow the directions in this section designed to guide you through a quick and correct installation of your new SY V6BE Mainboard For detailed information please refer to SY V6BE Mainboard Users guide and Technical Reference online manual included on the CD ROM packed with your mainboard vo or 22 eg Ow IERS PREPARATIONS Gather and prepare all the necessary hardware equipment to complete the installation successfully Pentium II processor with builtin CPU cooling fan boxed type
5. the CMOS memory and continue the boot sequence SY V6BE Quick Start Guide 4 The SOYO CD Your SY V6BE Mainboard comes with a CD ROM labeled SOYO CD The SOYO CD contains the user s manual file for your new mainboard the drivers software available for installation and a database in HTML format with information on SOYO mainboards and other products Step 1 Insert the SOYO CD into the CD ROM drive The SOYO CD will auto run and the SOYO CD Start Up Menu will display as shown below BI sovo CD Start Up Menu Etud 50YO Manuals Jastall Drivers Eater the SOW Ch Board Ja formation SOYO CD Start Up Program Menu The SOYO CD Start Up P rogram automatically detects which SOYO mainboard you own and displays the corresponding model name Step 2 Read SOYO model name Manual Click the Read Manual button to open the user s manual file of your mainboard 12 SY V6BE Quick Start Guide Please note that if the Start Up program was unable to determine which SOYO mainboard you own the manual selection menu will pop up as shown below Then select the user s manual file that corresponds to your mainboard model name and click OK SOYO CD Manuals X Please select your manual In the box below and click OK SY V6BE ly OK Back Manual Selection Menu The users manual files included on the SOYO CD can be read in PDF Postscript Document format In order to read a PDF file the appropriate Acrobat R
6. PUFAN power connector on the mainboard SY V6BE Quick Start Guide Step 2 Make Connections to the Mainboard This section tells how to connect internal peripherals and power supply to the mainboard Internal peripherals include IDE devices HDD CD ROM Floppy Disk Drive Chassis Fan Front Panel Devices Turbo LED Intemal Speaker Reset Button IDE LED and KeyLock Switch Wake On LAN card VGA card Sound Card and other devices For more details on how to connect intemal and extemal peripherals to your new SY V6BE Mainboard please refer to SY V6BE Mainboard Users Guide and Technical Reference online manual on CD ROM Connectors and Plug ins IrDA Infrared Device Header IR1 Wake On LAN Header JP44 us Pinl Pin2 Pin3 Pin4 Pin5 Pinl Pin2 Pin3 a VCC None IRRX GND RTX 5VSB GND MP Wakeup 2 0 CPU Cooling Fan CPUFAN Chassis Fan CHAFAN i Pinl Pin2 Pin3 Pini Pin2 Pin3 re GND 12V SENSOR GND 12V SENSOR z Power LED KeyLock Speaker Power LED Keylock Pinl Pin2 Pin3 Pil Pin2 OOOOO OOOO 5V NC GND ControlPin GND OO 1OO 10000 Speaker i 1 Pinl Pin2 Pin3 Pin4 Reset PWRBT Turbo LED HDD LED 5V NC C Speaker out HDD LED Turbo LED PWRBT RESET Pinel Pin2 Pin1 Pin2 Pin1 Pin2 Pini Pin2 LED LED Power LED Anode Catho
7. SY V6BE Mainboard Quick Start Guide SOYO SY V6BE Mainboard Pentium II processor amp Celeron processors AGP PCI Mainboard 66 amp 100MHz Front Side Bus supported ATX Form Factor Copyright 1998 by Soyo Computer Inc Trademarks Soyo is a registered trademark of Soyo Computer Inc All trademarks are the property of their owners Product Rights Product and corporate names mentioned in this publication are used for identification purposes only and may be registered trademarks or copyrights of their respective companies Copyright Notice All rights reserved This manual is copyrighted by Soyo Computer Inc You may not reproduce transmit transcribe store in a retrieval system or translate into any language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise any part of this publication without express written permission of Soyo Computer Inc Disclaimer Soyo Computer Inc makes no representations or warranties regarding the contents of this manual We reserve the right to revise the manual or make changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision or change The information contained in this manual is provided for general use by our customers Our customers should be aware that the personal computer field is the subject of many patents Our customers shoul
8. al situation 1 Tum off system power If you use a ATX power supply sometimes you have to press the power button for more then 4 seconds to shut down the system 2 Setthe SW1 to shortif you use a FSB 66MHz CPU Set the SW1 to open if you use a FSB 100MHz CPU 3 Press and hold down the Insert key while tuming on the system power Keep holding down the lt insert gt key until you see the message of the CPU type and frequency 133MHz or 200M Hz appear on screen 4 Press the lt Del gt key during the system diagnostic checks to enter the Award BIOS Setup program 5 Fromthe BIOS main menu select SOYO COMBO and move the cursor to the CPU Frequency field to set the proper working frequency 6 Select Save amp Exit SETUPJand press lt Enter gt to save the configuration to the CMOS memory and continue the boot sequence S 2e or 22 eE Ow I ag Note SOYO does not guarantee system stability if the user over clocks the system Any malfunctions due to over clocking are not covered by the warranty SY V6BE Quick Start Guide 3 Quick BIOS Setup This mainboard does not use any hardware jumpers to set the CPU frequency Instead CPU settings are software configurable with the BIOS SOYO COMBO SETUP The SOYO COMBO SETUP menu combines the main parameters that you need to configure all in one menu for a quick setup in BIOS After the hardware installation is complete tum the power switch on then press the lt DEL gt k
9. d ensure that their use of our products does not infringe upon any patents It is the policy of Soyo Computer Inc to respect the valid patent rights of third parties and not to infringe upon or assist others to infringe upon such rights Restricted Rights Legend Use duplication or disclosure by the Government is subject to restrictions set forth in subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause at 252 277 7013 About This Guide This Quick Start Guide is for assisting system manufacturers and end users in setting up and installing the mainboard Information in this guide has been carefully checked for reliability however no guarantee is given as to the correctness of the contents The information in this document is subject to change without notice If you need any further information please visit our Web Site on the Internet The address is http www soyo com tw SY V6BE Serial Version 1 0 Edition November 1998 These specifications are subjectto change without notice SY V6BE Quick Start Guide 1 Introduction Congratulations on your purchase of the SY V6BE Mainboard This Quick Start Guide describes the steps for installing and setting up your new mainboard This guide is designed for all users to provide the basic steps of mainboard setting and operation For further information please refer to SY V6BE Mainboard User s Guide and Technical Reference online manual included
10. de Cathode GND PowerGood GND On OF GND ATX Power On Off PWRBT ATX Power Supply ATX PW Connect your power switch to this Attach the ATX Power cable to this connector header momentary switch type When using the Power On by PS 2 Keyboard To turn off the system please _ function please make sure the ATX power press this switch and hold down supply can take at least 720mA load on the for longer than 4 seconds 5V Standby lead 5VSB to meet the standard ATX specifications SY V6BE Quick Start Guide Step 3 Configure Memory Your board comes with three DIMM sockets providing support for up to 768MB of main memory using DIMM modules from 8MB to 256MB For 66MHz frontside bus CPUs use 12ns or faster memory for 100M Hz front side bus CPUs use 8ns 100MHz PC 100 compliant memory Memory Configuration Table Number of Memory Modules DIMM 1 ee ee RAM Type SDRAM Memory Module Size MB 8 16 32 64 128 256 Mbytes Notex1 256 MB memory modules only available on PC registered DIMM 2 Always install memory modules in the order prescribed in this table 3 Do not install unbuffered and registered memory modules together V o Oo 22 eE Ow BEM Important It is of prime importance that you install DIMM modules as outlined in the table above in order to preserve signal integrity on 100M Hz front side bus systems Step 4 Set SW1 for power up FSB clock and AGP bu
11. e The USB supplement is available on the Windows OSR 2 or above CD in the following directory OSR 2 usbsupp exe Italso can be downloaded from www microsoftcom Step 4 Enter the SOYO CD Click the Enter SOYO CD button to enter the SOYO HTML database The Start Up program will activate the default HTML browser installed on your system for example Internet Explorer or Netscape to visualize the contents of the SOYO CD The SOYO CD contains useful information about your Mainboard and other SOYO products available in as many as eleven different languages F or your convenience this information is available in HTML format similar to the format widely used on the Intemet ENGLISH Wg sovo Introduction FAO Drivers Utilities BIOS Upgrades Manuals amp Quick Settings Product Information Contact Us SOYO CD HTML Database in English _ The list of menu options may vary between languages Note If no HTML browser is installed on your system the Start Up program will prompt you on whether or not you would like to install the Internet Explorer browser Click YES to install the HTML browser After the installation is complete please restart your system Then re run the SOYO CD and you will be able to browse the SOYO HTML database Intemet Explorer is a Microsoft Trademark Edition November 1998 International Headguarters Version 1 0 Soyo Computer Inc Taiwan SY V6BE SERIAL Tel 886 2 2290 3300 Fax 886 2 2298
12. eader software must be installed in your system Note The StartUp program automatically detects if the Acrobat Reader utility is already presentin your system and otherwise prompts you on whether or not you wantto install it You must install the Acrobat R eader utility to be able to read the user s manual file Follow the instructions on your screen during installation then once the installation is completed restart your system and re run the SOYO CD Step3 Install Drivers The following describes the best way of installing Windows 95 or Windows 98 on your SY V6BE mainboard gt The following BIOS default settings should not be changed 1 The OnChip USB Controller item under BIOS features Setup is setto enabled 2 The USB Assigned IRQ itemunder PnP PC Configuration is set to enabled You MUST have these two items enabled for Windows 95 98 to run properly on your system gt Install Windows 95 98 gt After installation of windows you will need to install theVIA drivers Follow the instruction below 13 SY V6BE Quick Start Guide Click the Install Drivers button to display the list of drivers that can be installed on your mainboard The start up program displays the drivers available for the SY V6BE and the Windows version you use For Windows 95 four drivers will be listed see Driver Installation Menu below for Windows 98 three drivers will be listed the ACPI drivers will be left out If you
13. ey during the system diagnostic checks to enter the Award BIOS Setup program The CMOS SETUP UTILITY will display on screen Then follow these steps to configure the CPU settings Step 1 Select STANDARD CMOS SETUP Set Date Time and Floppy drive type then set Hard Disk Type to Auto Step 2 Select LOAD SETUP DEFAULT Selectthe LOAD SETUP DEFAULT menu and type Y at the prompt to load the BIOS optimal setup te vo or eE Cw si EA Step3 Select SOYO COMBO SETUP Move the cursor to the CPU Frequency field to setthe CPU frequency Available CPU Frequency settings on your SY V6BE Mainboard are detailed in the following table If you set this field to Manual you are then required to fill in the next two consecutive fields 1 the CPU Host PCI Clock and 2 the CPU Ratio CPU Frequency Select the working frequency of your Pentium processor among LJ 233mHz 66x 3 5 Ll 400MHz 100 x 4 0 these preset values C 266mHz 66 x 4 0 C 450MHz 100x45 Note M Mark the checkbox that corresponds to the working L 300MHz 66 x 4 5 __ 500MHz 100 x 5 0 an L 333MHz 66 x 5 0 u processor in case the CMOS configuration should be lost L_ 350MHz 100 x 3 5 Note if you use Bus Frequencies of 75 MHz make sure that your PCI cards can cope with the higher PCI clock Step 4 Select SAVE amp EXIT SETUP Press lt Enter gt to save the new configuration to
14. on the CD ROM packed with your mainboard Cc ke WwW U 5 xe ke Ww Cc Unpacking lf your board comes with a driver disc and a paper manual the Quick Start Guide and the CD ROM are not included in the package When unpacking the mainboard check for the following items JA YA TheSY V6BE AGP PCI Mainboard Peng SS This Quick Start Guide The Installation CD ROM O Sr 4 The CPU Retention Set AA One IDE Device Flat Cable p One Floppy Disk Drive Flat Cable pap he Cc ke WwW U 5 pe ke Ww Cc SY V6BE Quick Start Guide Pi PS I2KB PS 2 Mouse SY V6BE Mainboard Layout Connector Connector JP10 ji woo H gt DIMM 1 C0 ID g X I e e DIMM USB 1 NN USB 2 Slot 1 for ra VE Pentiun Il Processor ee FDC PRT gt Fe COM 1f lo 2 mea 22 uan of LG jon COM 2 22 PARIR IES oe 1 1 IDE2 IDE1 3V Lithium y _ swt y ae PCI Slot 3 y ofa PCI Slot 4 VA 7 ble ml LED Menag aa Kaum Keylock PP Tweet o tones Lea _ Reset i JA CHAFAN Key Features gt Supports Intel Pentium II processor 233 gt
15. s clock SWI is used to adjustAGP bus clock frequency depending on the value of the front side bus FSB clock also the setting of the SW1 determines the power up FSB clock which will remain effective until the BIOS set the FSB clock to the CMOS setting SWI Setting Power up FSB Clock AGP Clock AGP Clock e 66MHz a FSB Clock 1 AGP Clock 100MHz i FSB Clock 1 5 Note The specification of maximum AGP bus Clock frequency is 66 6MHz X SetSWI to open when you use a FSB 100MHz CPU such as 350MHz 400MHz 450MHz or 500MHz X SetSWI to close when you use a FSB 66MHz CPU such as 233MHz 266MHz 300M Hz 333M Hz or 366Mhz only for Celeron X SetSWI to open when you use a FSB 66MHz but wantto over clock the FSB clock to 100M Hz via the BIOS setting SY V6BE Quick Start Guide Step 5 Set the CPU Frequency This mainboard does not use any jumpers to set the CPU frequency CPU setting are changed through the BIOS SOYO COMBO SETUP Refer to Chapter 3 Quick BIOS Setup for details on how to set the Pentium II processor frequency Step 6 Enable Disable Power On by Keyboard J P10 You can choose to enable the Power On by Keyboard function by shorting pin 1 2 on jumper J P10 otherwise short pin 2 3 to disable this function Power On by Keyboard Enable Disable Short pin 1 2 to enable the Short pin 2 3 to disable the JP10 Setting Power On by Keyboard function
16. wantto see all the drivers available on the SOYO CD click the Display all drivers on the SOYO CD button Do NOT install drivers that are not suitable for you board otherwise your system may crash Driver Installation X Please select the driver you want to install and click OK You will have to restart your system after installation Only the drivers that are relevant to your board are displayed initially VIA IRQ remapping utility VIA ACPI Driver SOYO SpeedPro BusMaster Driver VIA VxD Driver Display all drivers Canes on the SOYO CD oss Driver Installation Menu Select which driver you want to install and click OK or click Cancel to retum to the main menu When the installation program of a driver starts running the SOYO CD will exit After finishing the installation restartthe SOY O CD and install the next driver We recommend you to install all drivers and to do so in the right sequence top to bottom Note Once you have selected a driver the system will automatically exitthe SOYO CD to begin the driver installation program When the installation is complete most drivers require to restart your system before they can become active After installing all drivers above if you use Windows 95 first install the USB supplement before installing the AGP driver that came with your PN Install the drivers in sequence starting with the VIA IRQ remapping utility AGP card 14 SY V6BE Quick Start Guid
Download Pdf Manuals
Related Search