Sony CFD-S350L User's Manual
Contents
1. IF FM 10 7 MHz AM MW LW 450 kHz Aerials FM Telescopic aerials AM MW LW Built in ferrite bar aerials Cassette corder section Recording system 4 track 2 channel stereo Fast winding time Approx 120 s sec with Sony cassette C 60 Frequency response TYPE I normal 80 10 000 Hz General Speaker Full range 10 cm dia 3 2 Q cone type 2 Outputs Headphones jack stereo minijack For 16 68 Q impedance headphones Maximum Power output 5 2W Power requirements For CD radio cassette corder Malaysia Singapore and Thailand models 230 240 V AC 50Hz Korean model 220 V AC 60 Hz Other models 230 V AC 50 Hz 9 V DC 6 R20 size D batteries For remote control 3 V DC 2 R03 size AAA batteries Power consumption AC 14W Battery life For CD radio cassette corder FM recording Sony R20P approx 13 5 h Sony alkaline LR20 approx 20 h Tape playback Sony R20P approx 7 5 h Sony alkaline LR20 approx 15 h CD playback Sony R20P approx 2 5 h Sony alkaline LR20 approx 7 h Dimensions Approx 420 x 155 x 260 mm w h d 16 x 6 x 10 inches incl projecting parts Mass Approx 3 7 kg 8 Ib 3 oz incl batteries Supplied accessory Mains lead 1 Remote control 1 Design and specifications are subject to change without notice Optional accessories Sony MDR headphone series To prevent fire or shock hazard do not expose the player to rain or moistu2. or in a place subject to direct sunlight excessive dust or mechanical shock Do not place the player on an inclined or unstable place Do not place anything within 10 mm of the side of the cabinet The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components Ifthe player is left in a car parked in the sun be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun e Since a strong magnet is used for the speakers keep personal credit cards using magnetic coding or spring wound watches away from the player to prevent possible damage from the magnet On operation e Ifthe player is brought directly from a cold to a warm location or is placed in a very damp room moisture may condense on the lenses inside the CD player section Should this occur the player will not operate properly In this case remove the CD and wait about an hour for the moisture to evaporate Ifthe player has not been used for a long time set it in the playback mode to warm it up for a few minutes before inserting a cassette Notes on cassettes e Break off the cassette tab from side A or B to prevent accidental recording If you want to reuse the tape for recording cover the broken tab with adhesive tape Side A Tab for side A Tab for side B e The use of a cassette with more than 90 minutes of play time is not recommended e
3. I shuffle play SHUF Press Pll repeat tracks SHUF REP Press Pll in random order programme play PGM Press k or PI then press DISP ENT MEMORY for the tracks you want to programme in the order you want up to 20 tracks see fig Then press Pll repeat programmed tracks PGM REP Press k or BPI then press DISP ENT MEMORY for the tracks you want to programme in the order you want up to 20 tracks Then Press Pil On the remote When you ve selected PGM or PGM REP press the number buttons for the track you want up to 20 tracks then press B To cancel selected play mode Press MODE repeatedly until the selected mode disappears from the display To check the programmed track and playing order in the display To check the order of tracks before play press DISP ENT MEMORY Every time you press the button the track number appears in the programmed order To change the current programme Press W once if the CD is stopped and twice if the CD is playing The current programme will be erased Then create a new programme following the programming procedure Tips e You can play the same programme again since the programme is saved until you open the CD compartment e You can record your own programme After you ve created the programme insert a blank tape and press to start recording Listening to the radio 1 Press RADIO BAND AUTO PRESET until the band you want appears
4. Precautions On safety e As the laser beam used in the CD player section is harmful to the eyes do not attempt to disassemble the casing Refer servicing to qualified personnel only Should any solid object or liquid fall into the player unplug the player and have it checked by qualified personnel before operating it any further Discs with non standard shapes e g heart square star cannot be played on this player Attempting to do so may damage the player Do not use such discs Cleaning the cabinet e Clean the cabinet panel and controls with a soft cloth slightly moistened with a mild detergent solution Do not use any type of abrasive pad scouring powder or solvent such as alcohol or benzine On power sources For AC operation check that the player s operating voltage is identical with your local power supply see Specifications and use the supplied mains lead do not use any other type The player is not disconnected from the AC power source mains as long as it is connected to the wall outlet even if the player itself has been turned off For battery operation use six R20 size D batteries When the batteries are not to be used remove them to avoid damage that can be caused by battery leakage or corrosion The nameplate indicating operating voltage power consumption etc is located at the bottom On placement Do not leave the player in a location near heat sources
5. a gt gt PRESET gt gt I MEGA BASS PRESET I lt A The button has a tactile dot I Remote Sensor peee a Display Programmed track GiGi Playing order Falling asleep to music 1 Play the music source you want 2 Press SLEEP to display SLEEP 3 Press SLEEP to select the minutes until the player goes off automatically Each time you press the button the indication changes as follows 60 90 120 gt OFF 10 20 30 To cancel the sleep function Press OPERATE or POWER to turn off the power Note When you are playing a tape using this function If the tape length of one side is longer than the set time the player will not go off until the tape reaches the end Playing a CD 1 Press CD direct power on On the remote press OPERATE or POWER and then press FUNCTION repeatedly until Cd appears in the display 2 Load aCD in the CD compartment 3 Press amp PUSH OPEN CLOSE to close the CD compartment 4 Press PI BE on the remote The player plays all the tracks once To Press stop playback a pause playback Pil HE on the remote Press the button again to resume play after pause go to the next track PP go back to the previous track Hea PUSH OPEN CLOSE bP forward or lt 4 backward while playing until you find the point PPI or kK on the remote bP forward or lt 4 backward in pau
6. ce Suppress Switch that most decreases the noise For the best results use the AC power as a power source for recording To erase a recording proceed as follows 1 Insert a tape with the recording you want to erase 2 Press TAPE 3 Press
7. eplace the batteries be sure to take out the CD from the player To use the player on batteries disconnect the mains lead from the player e When you operate the player on batteries you cannot turn on the player using the remote Preparing the remote Insert two R03 size AAA batteries not supplied Replacing batteries With normal use the batteries should last for about six months When the remote no longer operates the player replace all the batteries with new ones Location of controls Inserting a cassette Loading a CD With the side you want to play facing you oooo o O o oooo o 4 PUSH OPEN CLOSE TAPE TUNE lt lt RADIO BAND AUTO PRESET TUNE gt gt DISP ENT MEMORY Pir MODE cp a OPR BATT Q MEGA BASS wy Display D l Total track number o 552 l To turn on off the power CFD S350L Press OPERATE CFD S350 Press POWER To adjust the volume Press VOLUME VOL on the remote To listen through headphones Connect the headphones to the Q headphones jack Adjusting the sound emphasis To reinforce the bass sound Press MEGA BASS MEGA BASS appears in the display To return to normal sound press the button again Remote Control Total playing time SLEEP FUNCTION OPERATE POWER Number buttons With the labeled side up MODE BAND VOL TUNE E amp PUSH OPEN CLOSE i VOLUME ie
8. er 1 Press RADIO BAND AUTO PRESET to select the band 2 Hold down RADIO BAND AUTO PRESET for 2 seconds until AUTO flashes in the display 3 Press DISP ENT MEMORY The stations are stored in memory from the lower frequencies to the higher ones If a station cannot be preset automatically You need to preset a station with a weak signal manually 1 Press RADIO BAND AUTO PRESET to select the band 2 Tune ina station you want 3 Hold down DISP ENT MEMORY for 2 seconds until the preset number flashes in the display 4 Press PRESET or until the preset number you want for the station flashes in the display 5 Press DISP ENT MEMORY The new station replaces the old one On the remote 1 Press BAND until the band you want appears in the display 2 Tune ina station you want 3 Hold down the number buttons that you want to preset the new station on for about 2 seconds To select the preset number over 10 press gt 10 first then the corresponding number buttons You need to hold down the last number button to enter for about 2 seconds Example To select 12 press gt 10 and 1 first then hold down 2 for about 2 seconds Tip The preset radio stations remain in memory even if you unplug the mains lead or remove the batteries Playing preset radio stations 1 Press RADIO BAND AUTO PRESET to select the band 2 Press PRESET or to tune in the stored station On the remote 1 Press BAND 2 Press the number buttons t
9. in the display direct power on Each time you press the button the indication changes as follows CFD S350 FM AM CFD S350L FM MW gt LW 2 Hold down TUNE or until the frequency digits begin to change in the display The player automatically scans the radio frequencies and stops when it finds a clear station If you can t tune in a station press the button repeatedly to change the frequency step by step Tip If the FM broadcast is noisy press MODE repeatedly until Mono appears in the display and the radio will play in monaural Changing the AM MW tuning interval The AM MW tuning interval is preset to 9 kHz at the factory If you need to change the AM MW tuning interval do the following 1 While keeping the RADIO BAND AUTO PRESET button and TAPE button pressed disconnect the mains lead from the mains 2 While keeping the RADIO BAND AUTO PRESET button and TAPE button pressed reconnect the mains lead to the mains The tuning interval is changed and AM 9 MW 9 or AM 10 MW 10 appears in the display for 2 seconds After changing the tuning interval you need to reset your preset radio stations Presetting radio stations You can store radio stations into the player s memory You can preset up to 30 radio stations CFD S350 20 for FM and 10 for AM in any order or 40 radio stations CFD S350L 20 for FM 10 for MW and 10 for LW in any ord
10. location free from vibration e Clean the lens with a commercially available blower e The sound may drop out or noise may be heard when using poor quality CD Rs CD RWs or if there is a problem with the recording device or application software Radio Reception is poor e Reorient the aerial to improve FM reception Reorient the player itself to improve AM or MW LW reception The audio is weak or has poor quality e Replace all the batteries with new ones if they are weak Move the player away from the TV The picture of your TV becomes unstable e If you are listening to an FM programme near the TV with an indoor aerial move the player away from the TV Tape Player The tape does not move when you press an operation button Close the cassette compartment securely The button does not function or the tape does not play or record e Make sure the safety tab on the cassette is in place Poor or distorted playback recording or erasing quality e Clean the heads pinch roller and capstan with a cleaning swab slightly moistened with cleaning fluid or alcohol Replace all the batteries with new ones if they are weak TYPE II high position or TYPE IV metal tape is being used Use TYPE I normal tape only Demagnetize the heads using a commercially available tape head demagnetizer Lens Pinch roller Erase head Capstan Record playback head Remote The rem
11. o tune in the stored station To tune in a preset station over 10 press gt 10 first then corresponding number buttons Example To tune in a preset station 12 press gt 10 and 1 first and then press 2 TEE 1 Press TAPE direct power on On the remote press OPERATE or POWER and then press FUNCTION repeatedly until TAPE appears in the display 2 Press W amp to open the tape compartment and insert a recorded tape Close the compartment Use TYPE I normal tape only 3 Press lt a To Press stop playback LEY fast forward or rewind the tape PP or lt lt pause playback i Press the button again to resume play after pause eject the cassette Es 1 Press BH to open the tape compartment and insert a blank tape Use TYPE I normal tape only 2 Select the programme source you want to record To record from the CD player Press CD and insert a CD See Playing a CD To record from the radio Press RADIO BAND AUTO PRESET and tune in the station you want See Listening to the radio 3 Press to start recording lt is depressed automatically To Press stop recording Ey pause recording H Press the button again to resume recording Tips Adjusting the volume or the audio emphasis will not affect the recording level CFD S350L only If the AM or MW LW programme makes a whistling sound after you ve pressed in step 3 press MODE to select the position of ISS Interferen
12. ote does not function e Replace all the batteries in the remote with new ones if they are weak e Make sure that you are pointing the remote at the remote sensor on the player Remove any obstacles in the path of the remote and the player e Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light Move closer to the player when using the remote After trying the above remedies if you still have problems unplug the mains lead and remove all the batteries After all the indications in the display disappear plug the mains lead and insert the batteries again If the problem persists please consult your nearest Sony dealer Specifications CD player section System Compact disc digital audio system Laser diode properties Material GaAlAs Wave length 780 nm Emission duration Continuous Laser output Less than 44 6 yW This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick up block with 7 mm aperture Spindle speed 200 r min rpm to 500 r min rpm CLV Number of channels 2 Frequency response 20 20 000 Hz 1 2 dB Wow and flutter Below measurable limit Radio section Frequency range CFD S350 FM 87 5 108 MHz AM 531 1 611 kHz 9 kHz step 530 1 610 kHz 10 kHz step CFD S350L FM 87 5 108 MHz MW 531 1 611 kHz 9 kHz step 530 1 610 kHz 10 kHz step LW 153 279 kHz
13. re SONY To avoid electrical shock do not open CD Radio iste Cassette Corder Operating Instructions WARNING Do not install the appliance in a confined space such as a bookcase or built in cabinet To prevent fire or shock hazard do not place objects filled with liquids such as vases on the appliance Connect the apparatus to an easily accessible AC outlet Should you notice an abnormality in the apparatus disconnect the main plug from the AC outlet immediately Notice for customers in the United Kingdom A moulded plug complying with BS 1363 is fitted to this equipment for your safety and convenience Should the fuse in the plug supplied need to be replaced same rating fuse approved by ASTA or BSI to BS 1362 i e marked with amp or Y CFD S350 mark must be used CFD S350L If the plug supplied with this equipment has a detachable fuse cover be sure to attach the fuse cover after you change the fuse Never use the plug without the fuse cover If you should lose the fuse cover please contact your nearest Sony 2005 Sony Corporation service station 2 548 052 13 1 548 052 13 1 http www sony net Power Sources Connect the mains lead BN or insert six R20 size D batteries not supplied into the battery compartment E Notes Replace the batteries when the OPR BATT indicator dims or when the player stops operating Replace all the batteries with new ones Before you r
14. se until you find the point BPI or kK on the remote a number button of the track on the remote remove the CD locate a point while listening to the sound locate a point while observing the display locate a specific track directly You cannot locate a specific track if SHUF or PGM is lit in the display Turn off the indication by pressing W Tip To locate a track numbered over 10 press gt 10 first then the corresponding number buttons on the remote Example To play track number 23 press gt 10 first then 2 and 3 Using the display To check the total track number and playing time Press DISP ENT MEMORY in stop mode see fig BD To check the remaining time Press DISP ENT MEMORY repeatedly while playing a CD The display changes as follows the current track number and playing time l the current track number and the remaining time on the current track l L the numter of tracks left and remaining time on the CD For a track whose number is more than 20 the remaining time appears as in the display Selecting the play mode Press MODE until REP 1 REP ALL SHUF SHUF REP PGM PGM REP appears in the display Then proceed as follows To Select Then do this repeat a single track REP 1 Press k or gt P to select the track that you want to repeat then press Pll repeat all tracks REP ALL Press PA
15. ur player please consult your nearest Sony dealer Troubleshooting General The power does not come on e Make sure the batteries are inserted correctly Replace all the batteries with new ones if they are weak e You cannot turn on the player with the remote when you operate the player on batteries The power is not on and bAttErY and Error are displayed alternately e Make sure the batteries are inserted correctly Replace all the batteries with new ones if they are weak There is no audio e Adjust the volume e Unplug the headphones when listening through speakers Noise is heard e Someone is using a portable telephone or other equipment that emits radio waves near the player Move the portable telephone etc away from the player CD Player The CD does not play or no dISC lights in the display even when a CD is in place Place the CD with the label surface up e Clean the CD Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation The CD R CD RW was not finalized Finalize the CD R CD RW with the recording device e There is a problem with the quality of the CD R CD RW recording device or application software The CD R CD RW is blank Replace all the batteries with new ones if they are weak The sound drops out e Reduce the volume Clean the CD or replace it if the CD is badly damaged Place the player in a
16. xcept for long continuous recording or playback Notes on CDs Before playing clean the CD with a cleaning cloth Wipe the CD from the center out Do not use solvents such as benzine thinner commercially available cleaners or anti static spray intended for vinyl LPs Do not expose the CD to direct sunlight or heat sources such as hot air ducts nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car Do not stick paper or sticker on the CD nor scratch the surface of the CD e After playing store the CD in its case If there is a scratch dirt or fingerprints on the CD it may cause tracking error About CD Rs CD RWs This player can play CD Rs CD RWs recorded in the CD DA format but playback capability may vary depending on the quality of the disc and the condition of the recording device CD DA is the abbreviation for Compact Disc Digital Audio It is a recording standard used for Audio CDs Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc CD standard Recently various music discs encoded with copyright protection technologies are marketed by some record companies Please be aware that among those discs there are some that do not conform to the CD standard and may not be playable by this product If you have any questions or problems concerning yo
Download Pdf Manuals
Related Search