Sony CDU948S User's Manual
Contents
1. Power T TIRA Supply 2 So INTERFAN Cable Audio Cable E supplied SCSI Cable Not included Red Edge O 49 T ns i oo p Sound Card Not included SCSI Card Not included Speakers Not included Step 10 Closing the Computer Carefully replace computer cover and reinstall screws per Owner s Manual Now hardware installation is complete 14 Hardware Installation Software Installation Please refer to CD R formatting software manual for instruction on software installation CD R formatting software must first be properly installed in order to write CD s with the CDU948S drive Using Discs and Caddies Loading a Disc into a Standard Caddy 1 Press both tabs at opposite end to shutter to open caddy lid Note CD R disc s recording surface must be clean please do not touch it Data cannot be recorded is CD s recording surface is contaminated Software Installation Using Discs and Caddies 15 3 Close the lid firmly 4 Do not manually open slide Storing Discs and Caddies e Remove the caddy from the drive before moving drive e Do not store the disc or caddy in a location subject to high humidity high temperature excessive dust direct sunlight Care of Discs e Only hold disc by its edge Do not touch the record surface Wipe CD ROM disc with optional CD cleaner to clean it e Do not wipe CD R discs before recording data To avoid scra2. SCSI host adapter connector Pin 1 red Opposite End Note If no free 50 pin SCSI connector exists see Troubleshooting page 19 Step 4 Choosing the Configuration M SCSI ID selection M Termination If no other SCSI devices are in the system we recommend the default Jumper settings In this case go on to Step 6 Connecting the Drive If one or more SCSI ID s are assigned you must determine if the default ID 6 is free If SCSI ID 6 is assigned you must change the CD R drive to a free ID via jumpers at rear of drive If CD R drive is on end of SCSI cable leave terminators in place If CD R drive is not on end of SCSI cable or last physical device carefully remove the drive termination resistors and assure the last physical SCSI device is properly terminated or activated Note Only the last physical SCSI device needs to be terminated Hardware Installation 9 Step 5 Setting the Jumpers Set jumpers on rear of drive unit according to your computer configuration Jumpers are factory preset as shown below DEVICE TYPE PREVENT ALLOW ID SELECT di TEST MODE Terminators ODE Low TESTATA PREVI GIOE gree Oe 10 Hardware Installation The following table shows the function of each jumper Jumper Function DEVICE The setting of this jumper determines whether the TYPE SCSI device type code in the inquiry data is WO or CD ROM ON WORM OFF CD ROM ID
3. and quadruple speeds along with read only at 8x speed e Fast access time assures high speed reading and writing Audio e Outputs 16 bit digital audio data over SCSI interface e Audio CD playback via Audio Out and headphones jack Note Please read this manual thoroughly before attempting installation System Requirements for WINDOWS 95 NT e System requirements of format software SCSI host adapter card 20 MB or more free Hard Disc space 3 5 floppy disk drive Mouse Microsoft compatible 16 MB of RAM or more Introduction 5 Location and Function of Parts and Controls Front Panel Caddy insertion slot Emergency eject hole Busy indicator Eject button Headphones jack Volume control This indicator shows the unit s status in various phases of operation Seek read and write Flashes amber Error Lights up amber and stays lit When the power is turned on the indicator lights up green Rear Panel Jumper block for SCSI bus Terminators Power in connector GND GND JO ooo00o00000000000000000000 Dol ooo00000000000000000 0rcjooa O000 INTERFACE CONNECTOR 1 LJ 5V 5 GND 12V 10 DC INPUT TEST MODE PREVENT ALLOW ID SELECT DEVICE TYPE LI LGNDR AUDIO OUT Frame ground
4. CAS D OUVERTURE EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU VORSICHT UNSICHTRARE LASERSTRAHLUNG WENN ABDECKUNG GE FFNET ICHT DEM STRAHL AUSSETZE ADVARSEL pa LASERSTR LING VED pa UNDGA UDS ETTELSE FOR STRALING ADVARSEL USYNLIG LASERSTRALING NAR DEKSEL PNES UNNG EKSPONERING FOR STR LEN VARNING OSYNLIG LASERSTRALING N R DENNA DEL AR PPNAD STRALEN R FARLIG VAROI NAKYMATON AVATTAESSA OLET ALTTINA LASERSATEILYLLE ALA KATSO SATEESEN This label is located on the bottom of the drive unit enclosure This unit uses CD R discs with the following mark MSE CEAD This unit uses CD ROM discs with the following mark SC When you use this unit as a CD player use compact COMPACT discs with the following mark MSE DIGITAL AUDIO You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular inst
5. SELECT Assign the drive unit s ID number by setting these jumpers to ON or OFF Do not assign the same number as one used for other SCSI device ID number Jumper settings 0 1 2 0 OFF OFF OFF 1 ON OFF OFF 2 OFF ON OFF 3 ON ON OFF 4 OFF OFF ON 5 ON OFF ON 6 OFF ON ON n ON ON ON KEY Used to prevent the SCSI bus interface connector from being plugged in upside down PREVENT ON Allows insert and removal of a CD caddy ALLOW with the eject button and the eject command OFF Prevents insert and removal of a CD caddy with the eject button or an eject command TEST MODE ON Enables test mode OFF Enables normal operation Factory settings Notes e The upper row of pins is without position KEY is ground e Remove jumper to set OFF install jumper to set ON e ID SELECT PREVENT ALLOW and TEST MODE are recognized when the power supply is turned on or the SCSI bus is reset e TEST MODE is used exclusively for factory testing Do not set TEST MODE to ON Doing so may cause unexpected results Hardware Installation 11 Step 6 Connecting the Drive Attach flat SCSI cable to connector at rear of CD R drive ie 1 Interface Connector Power Supply Connector Audio Out Connector D Red Edge SCSI Flat Cable Cable Red Wire Notes The 50 pin flat SCSI cable must be firmly attached wit
6. on the drive unit Notes e Eject button does not function if software disabled e To eject a caddy when physical eject is software disabled Assure jumper block s PREVENT ALLOW is set to ON Switch computer off then on or software reset SCSI bus E Ejecting a caddy manually in an emergency In the event of electrical or mechanical drive failure a manual emergency eject is provided to allow manual caddy removal 1 Turn off the computer 2 Insert a pointed object perhaps a paper clip into the emergency eject hole and push typical force required is 46 N 4 7 kg at least 35 mm After thus removing caddy consult dealer or qualified service point 18 Operating the Drive Troubleshooting Should problems arise installing or operating the drive e Please verify the steps of this manual were carefully followed e If problem still exists please confirm the items in Checklist below Checklist Please verify the following e Power cable properly attached to drive Step 8 on page 13 When properly connected the LED lights green e Both ends of SCSI cable are properly attached check pin 1 position e SCSI ID of CD R is unique to SCSI bus Compare all other SCSI devices internal and external and see Step 2 Step 5 pages 8 10 e Check all other jumpers on rear of drive We recommend factory defaults on pages 10 and 11 with a SCSI ID 6 if possible e Assure SCSI bus is properly terminated or activ
7. tab Audio output connector SCSI bus interface connector 6 Location and Function of Parts and Controls Precautions Installation Avoid placing the drive in a location subject to high humidity high temperature excessive dust mechanical vibration direct sunlight Only horizontal drive operation recommended not tilted Operation e Do not move drive during operation it may cause an error e Avoid exposing the drive to sudden temperature changes as condensation may form on a lens inside the drive Should the surrounding temperature suddenly rise during operation wait at least 1 hour before turning off power Operation immediately after a temperature rise may cause a malfunction as well Transportation Keep the original packing materials for future transport of the drive Remove caddy before moving or repackaging drive Hardware Installation Installing the Drive Unit into the Computer Before starting this section you may wish to consult your computer s manual for a more detailed description of installing new hardware Our example assumes an IBM PC AT compatible computer a SCSI adapter card and a SCSI interface cable 50 pin flat are supplied Getting Started Assure a SCSI adapter is installed before installing the CD R drive Prepare the necessary parts and tools not supplied a screwdriver Two mounting rails if computer has mounting tracks e Unplug and disconnect any attache
8. CDU948S CD R Drive Unit User s Guide Mode d emploi Bedienungsanleitung Manual de instrucciones Manuale d istruzione 1998 by Sony Corporation Rev 1 0 BKC 98000668 CDU948S CD R Drive Unit User s Guide Mode d emploi Bedienungsanleitung Manual de instrucciones Manuale d istruzione Owner s Record The model and serial numbers are located on the bottom of the drive Record these numbers in the spaces provided below Refer to them whenever you call upon your sales representative regarding this product Model No Serial No Safety Regulations To prevent fire or shock hazard do not expose the unit to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only Caution As the laser beam in this CDU948S is harmful to the eyes do not attempt to disassemble the cabinet Refer servicing to qualified personnel only The use of optical instruments with this product will increase eye hazard The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation DANGER INVISIBLE LASER RADIATION WHEN OPEN AVIOD DIRECT EXPOSIRE TOP BEAM VORSICHT This label is located on the drive unit s internal chassis ee LASERSTRAHLUNG WENN ABDECKUNG NICHT DEMSTRAHL AUSSETZEN DANGER INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM DANGER RADIATIONS INVISIBLES DU LASER EN
9. allation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CLASS 1 This CD R drive unit is classified as a CLASS 1 LASER LASER PRODUCT PRODUCT LASER KLASSE 1 The CLASS 1 LASER PRODUCT label is located at the PRODUKT bottom of the enclosure Trademarks Windows and Windows 95 NT are registered trademarks of Microsoft Corporation IBM PC AT is a registered trademarks of International Business Machines Contents Introduction 5 Features a ite Mid e ong cies drain a hee 5 System Requirements for WINDOWS 95 NT see eeeteeeeeeteeeteeeeaes 5 Location and Function of Parts and Controls 6 Front Panel Rear Panel ha narra 6 Precautions 7 Hardware Installation 7 Installing the Drive Unit into the Computer ii 7 Getting started Step 1 Opening the Computer Step 2 SCSI Configuration Step 3 Finding the Connector Step 4 Choosing the Configuratio
10. ated at both ends For details please see Step 4 Termination on page 9 Should you still have problems operating or installing your CD R drive please contact Hotline or local computer dealer Additional Installation Cases E No free SCSI connector present If other SCSI devices occupy every bus connector either remove a device before installing CD R drive or use a SCSI cable with more connectors Please contact local computer dealer for details E 68 Pin SCSI Cable If only a wide SCSI cable 68 pin exists in the computer a 50 pin adapter is necessary Troubleshooting 19 ee Specifications M General Host interface SCSI 2 single ended 50 pin Supported Read Write formats Read only Write Methods Write Read Speed Write Read E Audio Line out Headphone M Environmental conditions Relative humidity Climate gradient Temperatures Operating Transport 72 hours max Storage 6 month max E Drive Mass CD ROM Mode 1 amp 2 CD ROM XA Mode 2 Form 1 amp 2 CD Audio Audio combined CD ROMs includes CD EXTRA CD I Mode 2 Form 1 amp 2 CD I Ready CD Bridge CD R conforming to Orange Book Part II Incremental Write Session at Once Track at Once Variable amp Fixed Packet Track Reservation Disk at Once 1X 2X 4X 2X only for packet write 1X 2X 4X 8X 1X 150 kbytes sec 0 7 V at 47 KQ 0 55 V at 32 Q 10 to 90 no condensation 10 C hour 10 humidity
11. d computer cables for your own safety Restore power only after completing installation Precautions Hardware Installation 7 Step 1 Opening the Computer Remove the computer s cover as directed in the Owner s Manual Step 2 SCSI Configuration 8 Locate the 50 pin SCSI cable in your computer One end of the cable is connected to the SCSI host adapter card as shown below 4 SCSI Host Adapter Card ZZ is R gt ni Red Edge EY SCSI SCSI SCSI Device Device Device Note The following types of cables may be installed in your computer Find this DI flat cable Floppy Disk ille SHE Lila Drive Cable IDE Cable Note There may already be internal or external SCSI devices HDD Scanner CD ROM connected to the SCSI cable If so you must determine the SCSI ID of each SCSI device This information will be required for Step 5 Setting the Jumpers Refer to SCSI device s for ID data In some cases a SCSI chip set may be implemented in the motherboard Hardware Installation wr wr 40 Pi 34 Pin ha I I Step 3 Finding the Connector The SCSI cable should have 1 or more unused connectors on the end opposite the adapter as shown find a connector not in use We recommend a connector at the very end of the 50 pin SCSI cable
12. h its red edge Pin 1 positioned next to the power supply connector If your computer has a Sound Card an Audio Cable may be connected to the rear of the CD R drive Contact a local dealer if cable is required 12 Hardware Installation Step 7 Mounting the Drive Insert the CD R drive into computer front as shown routing cables accordingly Secure drive to frame with appropriate screws Audio Cable Note Slide rails not included may be necessary if CD R drive cannot cannot be secured Refer to computer s User s Guide for more information Step 8 Connecting the Power Cable Locate an available power supply cable within computer and connect it to the rear of CD R drive as shown Power Supply Connector 5Vt5 GND 12V 10 DC INPUT Power Supply Cable Note The power supply cable connector is designed to fit one way do not force it upside down this could damage drive and void the warranty Hardware Installation 13 Step 9 Installation Review Now review the hardware installation process assuring that All connectors are properly connected Each SCSI device has its own unique SCSI ID number The last physical SCSI device on the bus is properly terminated Red Edge Notes Red edge of 50 pin flat SCSI cable must be on pin 1 of host adapter e The following is a sample configuration of CDU948S installation CDU948S Drive
13. hour 5 C to 40 C 41 F to 104 F 40 C to 60 C 40 F to 140 F 30 C to 50 C 22 F to 122 F 1 04 kg Design and specifications subject to change without notice 20 Specifications M Dimension diagram 41 4 146 4 21 9 e 139 7 10 gt lt N LUI s a a 2 i A N va 2 v a x Ok 2 i 4 M3 Mounting la 148 5 screws 4 M3 Mounting screws o ca i q cu vt v 0 8 ae 0 8 42 5 p Unit mm Important Screws must not extend more than 4 0 mm into the side panels or the bottom plate Specifications 22
14. n Step 5 Setting the JUMPers Step 6 Connecting the Drive S Step 7 Mounting the Drive i Step 8 Connecting the Power Cable ii 13 Step 9 Installation Review Po Step 10 Closing the Computer 14 Software Installation 15 Using Discs and Caddies 15 Loading a Disc into a Standard CaddY i 15 Storing Discs and Caddies i 16 Gare 0f DISCS i iaia ie 16 Operating the Drive 17 Startingi Upss snai aaa anice Ejecting a Caddy Troubleshooting 19 Checklist sleale bai 19 Additional Installation Cases ii 19 Specifications 20 Introduction Features This manual assists you with the 4x write 8x read CDU948S drive which uses CD R media storing up to 650 Mbytes of data The drive unit has the following features General e 5 1 4 inch half height drive form factor Fast SCSI bus interface embedded Based on SCSI 2 2 Mbytes of buffer memory Power loading and power eject Emergency eject function allows manual caddy ejection Supported disc formats e Reads and writes data in both CD ROM CD ROM XA additional hard and software standard formats e Reads and writes CD BRIDGE format includes PHOTO CD e Reads standard CD DA Red Book encoded discs reads and writes CD R discs conforming to Orange Book Part II Performance e Supports read and write operation at standard double
15. tching the recording surface blow away dust using an air blower 16 Using Discs and Caddies Operating the Drive Starting Up Assure application software is installed before using the CD R drive 1 Turn on the power supply 2 Insert caddy into drive slot with disc label facing up Push gently until auto load mechanism pulls caddy into drive Important When loading a caddy do not attempt to overpower the auto load As the drive begins reading the Table of Contents TOC data the busy indicator lights amber and remains illuminated until read is completed When the busy indicator changes to green the drive is ready to receive commands data may be retrieved from the disc After loading a disc it takes a moment for the drive to become ready while Program Memory Area is read From this point follow instructions provided with the application software Notes e Drive will not permit caddy insertion if PREVENT ALLOW option in jumper block is set to OFF Host computer is set to PREVENT mode via software e Busy indicator on drive continues to light amber if Disc is not properly inserted or a malfunction occurs In such a case eject the caddy and reinsert it properly Should the light remain amber consult dealer or qualified service point During audio play the busy indicator remains amber this is normal Operating the Drive 17 Ejecting a Caddy 1 Turn on the computer s power supply 2 Press eject button
Download Pdf Manuals
Related Search