Smeg PGA64 User's Manual
Contents
1. For easier cleaning the pan stands burner caps flame spreader crowns and burners can all be removed wash them with warm water and a non abrasive detergent making sure to remove any encrustation then wait until they are completely dry Replace the burner caps on their corresponding crowns making sure that the slots A are centred with the pins B on the L burners For correct operation the igniters and thermocouples must always be perfectly clean Check them frequently and clean them with a damp cloth if necessary Remove any dry residues with a wooden toothpick or a needle 29 Instructions for the installer 6 POSITION NEAR THE COUNTER TOP 2D The following operation requires building and or carpentry work so must be carried out by T a competent tradesman Installation can be carried out on various materials such as masonry metal solid wood or plastic laminated wood as long as they are heat resistant T 90 C 6 1 Fixing to a support structure model with traditional casing fig 1 Create an opening with the dimensions shown in the figure in the top surface of the counter keeping a minimum distance of 50 mm from the rear edge This appliance can be mounted against walls higher than the work surface on condition that a distance of X be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating Make sure that there is a minimum of 750 mm between the2. 1 1 05 en O Ultra rapid 3 3 90 135 1600 7 3 Arrangement of the burners on the cooking hob HOB 1 Auxiliary 2 Rapid 3 Ultra rapid 37 Instructions for the installer 8 FINAL OPERATIONS After making the adjustments described above reassemble the appliance by following in reverse the instructions reported in paragraph 7 1 Replacement of the cooking hob nozzles 2 After adjustment with a gas other than the preset one replace the label on the KN casing of the appliance with the label corresponding to the new gas This label WE 2 can be obtained from the nearest Authorised Service Centre 8 1 Adjusting the minimum for town and natural gas Light the burner and turn it to the minimum position Extract the gas tap knob and turn ll the adjustment screw inside or next to the tap rod depending on the model until the correct minimum flame is achieved Refit the knob and verify that the burner flame is stable when turning the knob rapidly from the maximum to the minimum position the flame must not go out Repeat the operation on all the gas taps I TU 8 2 Adjusting the minimum setting for liquid gas To adjust the minimum setting with liquid gas you must tighten the screw inside or next to the tap rod depending on the model fully in a clockwise direction The diameters of the by passes for the individual burners are given in the paragraph 7 2 Burner and nozzle characteristics tables 8 3 Lubr
3. far enough to prevent the liquid from boiling over To prevent burns or damage to the hob during cooking all pans or griddles must be placed inside the perimeter of the hob Take the greatest care when using fats or oils since they may catch fire if overheated 4 3 Pan diameters HOB BURNER min and max in cm 1 Auxiliary 2 Rapid 12 16 3 Ultra rapid 18 24 22 26 The supplied reduced grill must only be used for Chinese wok pans Instructions for the user GB IE 5 CLEANING AND MAINTENANCE Before performing any operations requiring access to powered parts aa switch off the power supply to the appliance NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE 5 1 Cleaning stainless steel To keep stainless steel in good condition it should be cleaned regularly after use Let it cool first a EA 5 1 1 Ordinary daily cleaning To clean and preserve the stainless steel surfaces use only specific products that do not contain abrasives or chlorine based acids How to use pour the product onto a damp cloth and wipe the surface rinse thoroughly and dry with a soft cloth or chamois leather 5 1 2 Food stains or residues Never use metallic sponges or sharp scrapers as they will damage the surface SE Use ordinary non abrasive products for steel with the aid of wooden or plastic utensils if necessary Rinse thoroughly and dry with a soft cloth or chamois leather iy 5 2 Cleaning the cooking hob parts
4. hob and any shelf that may be installed directly above it Carefully position the supplied insulating seal on the outer edge of the hole on the top hob as indicated in figure 2 Try and make it stick to the whole surface by applying light hand pressure The front and back sides of the seal must be touching the hole Carry out this operation by supporting the hob on the isolating seal and using screws and clamping brackets Fig 3 to fix the gt U hob to the support structure in order to obtain the complete flatness Trim any excess trimming from border A with care Fig 4 The quotes in figure 2 are 3 references for the hole on the inside of the trimming The small brackets in figure 3 are only positioned after having mounted the hob 30 PY Instructions for the installer 6 2 Fixing to the electric model support structure Create an opening with the dimensions shown in the figure in the top surface of the counter keeping a minimum distance of 50 mm from the rear edge The lower part of the casing must be fully accessible after the appliance has been installed This appliance can be mounted against walls higher than the work surface on condition that a distance of X be kept between the appliance and the wall as shown in the figure so as to avoid damage from overheating Make sure that there is a minimum of 750 mm between the hob ring flames and any shelves placed directly above them
5. C ee 2 0 Q 3 D E 3 8 E OL 2 eg gt gt ON g A 3 So q Contents 1 INSTRUCTIONS FOR USE nero 22 BO PRECAUTION Se ce 24 3 ENVIRONMENTAL RESPONSIBILITY cc eeeeeeeeteeeee reais 26 NIN a THE HOB a a nt 27 5 CLEANING AND MAINTENANCE NN 29 6 POSITION NEAR THE COUNTER TOP NN 30 7 ADAPTATION TO DIFFERENT TYPES OF GAS eee 36 o FINACOFERA TON a 38 THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS MAN UAL INSTRUCTIONS FOR THE USER these instructions contain user 4 recommendations a description of the controls and the correct procedures for cleaning and maintenance of the appliance INSTRUCTIONS FOR THE INSTALLER these are intended for the qualified X technician who must install the appliance set it functioning and carry out an inspection test 21 i Y Vy 7 p 22 General instructions yN 1 INSTRUCTIONS FOR USE THIS MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE THIS MANUAL CONSTITUTES AN INTEGRAL PART OF THE APPLIANCE IT SHOULD BE KEPT INTACT AND AT HAND FOR THE APPLIANCE S ENTIRE LIFE CYCLE IT IS IMPORTANT TO CAREFULLY READ THIS MANUAL AND ALL THE INSTRUCTIONS CONTAINED HEREIN BEFORE USING THE APPLIANCE INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL AND COMPLY WITH THE REGULATIONS IN FORCE THIS APPLIANCE
6. Fig 1 Furthermore this kind of appliance needs a milling on the hob top of 3 mm in depth the measurements are indicated in figure 4 detail A of figure 2 Before positioning the hob the supplied adhesive sponge E should be spread out flat over the milling surface fig 2 Carry out this operation by supporting the hob on the isolating seal and using screws and clamping brackets Fig 3 sequence to fix the hob to the support structure in order to obtain the complete flatness The small brackets in figure 3 are only positioned after having mounted the hob A es EN et 6 T L lt 0 7 gt lt A gas NS gg YS is EC oF 1 R145 SS S E Ss TE E 7 3 s BDB 62 92 gt en gt P o9 on If laminated surfaces are used it is advisable to spread a layer of anti infiltration primer across the milled surface Important Other types of installation are possible if supervised by the manufacturer 31 else l Instructions for the installer Obstructions location of gas and electric connectors measured in mm 620 134 97 73 co H co N N oe ip 74 a Hoot Het
7. IS SPECIFIED FOR DOMESTIC USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE THE APPLIANCE IS MANUFACTURED IN ORDER TO PERFORM THE FOLLOWING FUNCTIONS COOKING FOOD IT IS CONSIDERED UNSUITABLE FOR ANY OTHER USE THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR USES OTHER THAN THOSE INDICATED IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS DO NOT USE IT AS A ROOM HEATER NEVER USE THIS APPLIANCE TO HEAT YOUR ENVIRONMENT THIS APPLIANCE IS MARKED FOR IDENTIFICATION PURPOSES IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE 2002 96 EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT WEEE THIS DIRECTIVE STATES THAT THE REGULATIONS FOR THE COLLECTION AND RECYLING OF DISCARDED APPLIANCES ARE VALID WITHIN THE EUROPEAN UNION BEFORE OPERATING THE APPLIANCE IT IS MANDATORY TO REMOVE ALL PROTECTIVE FILM SUITABLE HEAT PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS DO NOT USE STEEL SPONGES AND SHARP SCRAPERS AS THEY WILL DAMAGE THE SURFACE LE USE NORMAL NON ABRASIVE PRODUCTS INCLUDING WOODEN OR PLASTIC UTENSILS IF NECESSARY RINSE THOROUGHLY AND DRY USING A SOFT CLOTH OR A MICROFIBRE CLOTH a DO NOT LEAVE THE APPLIANCE UNATTENDED DURING COOKING PROCESSES WHERE FATS OR OILS COULD BE RELEASED FATS AND OILS MAY CATCH FIRE General instructions GB IE A ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE O OFF POSITION WHEN YOU FINISH USING THE APPLIANCE A cy EBO NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLA
8. LT IN NEVER DISCONNECT THE PLUG BY PULLING ON THE CABLE IF THE POWER SUPPLY CABLE IS DAMAGED CONTACT THE TECHNICAL SUPPORT SERVICE IMMEDIATELY AND THEY WILL REPLACE IT Yt IT IS OBLIGATORY FOR ALL ELECTRICAL EQUIPMENT TO BE EARTHED ACCORDING TO THE METHODS LAID DOWN BY SAFETY REGULATIONS IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST FOLLOWING THE INSTRUCTIONS BELOW SHOULD THE APPLIANCE NOT FUNCTION DISCONNECT IT FROM THE ELECTRICITY SUPPLY AND CALL THE NEAREST TECHNICAL SUPPORT CENTRE NEVER ATTEMPT TO REPAIR THE APPLIANCE DURING USE THE APPLIANCE BECOMES VERY HOT MAKE SURE YOU DO NOT TOUCH THE HEATING ELEMENTS THIS APPLIANCE MAY NOT BE USED BY PEOPLE INCLUDING CHILDREN OF REDUCED PHYSICAL AND MENTAL CAPACITY OR LACKING IN EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES UNLESS THEY ARE SUPERVISED OR INSTRUCTED BY ADULTS RESPONSIBLE FOR THEIR SAFETY gt amp Pe General instructions GB IE DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR PLAY WITH IT AT ANY TIME DO NOT INSERT POINTED METAL OBJECTS CUTLERY OR UTENSILS INTO THE SLITS IN THE APPLIANCE DO NOT USE STEAM JETS FOR CLEANING THE APPLIANCE THE STEAM COULD REACH THE ELECTRONICS DAMAGING THEM AND CAUSING SHORT CIRCUITS DO NOT MODIFY THIS APPLIANCE DO NOT SPRAY ANY SPRAY PRODUCTS NEAR THE ELECTRICAL APPLIANCE WHILE IT IS IN OPERATION DO NOT USE SPRAY PRODUCTS WHILE THE PRODUCT IS STILL HOT Th
9. T AND SMOOTH ON THE COOKING HOB PAN STANDS NEVER USE PANS OR GRIDDLE PLATES WHICH PROJECT BEYOND THE OUTSIDE _ EDGE OF THE HOB 23 GB IE General instructions yN 2 SAFETY PRECAUTIONS REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY REGULATIONS FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION FUNCTIONS IN YOUR INTERESTS AND FOR YOUR SAFETY THE LAW REQUIRES THAT THE INSTALLATION AND SERVICING OF ALL ELECTRICAL APPLIANCES IS CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE OUR APPROVED INSTALLERS GUARANTEE A SATISFACTORY JOB GAS OR ELECTRICAL APPLIANCES MUST ALWAYS BE DISCONNECTED BY SUITABLY SKILLED PEOPLE BEFORE CONNECTING THE APPLIANCE TO THE POWER GRID CHECK THE DATA ON THE PLATE AGAINST THE DATA FOR THE GRID ITSELF THE IDENTIFICATION PLATE CONTAINING THE TECHNICAL DATA SERIAL NUMBER AND BRAND NAME IS IN A VISIBLE POSITION UNDER THE CASING C DO NOT REMOVE THIS PLATE ON THE CASING FOR ANY REASON BEFORE CONNECTING THE DEVICE MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT CHECKING THE LABEL UNDER THE CASING BEFORE CARRYING OUT INSTALLATION MAINTENANCE WORK MAKE SURE THAT THE APPLIANCE IS NOT CONNECTED TO THE POWER GRID a SE gt THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND ITS SOCKET MUST BE OF THE SAME TYPE AND CONFORM TO THE REGULATIONS IN FORCE THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUI
10. alth and the environment in accordance with current European directives 3 2 Your environmental responsibility Our products packing is made of non polluting materials which are therefore compatible with the environment and recyclable Please help by disposing of the packaging correctly You can obtain the addresses of collection recycling and disposal centres from your retailer or from the competent local organisations Do not discard the packaging or any part of it or leave it unattended It can constitute a suffocation hazard for children especially the plastic bags Your old appliance also needs to be disposed of correctly Important hand over your appliance to the local agency authorised for the collection of electrical appliances no longer in use Correct disposal enables intelligent recovery of valuable materials Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use to ensure that children cannot accidentally become trapped inside during play It is also necessary to cut the connecting cable to the power grid removing it along with the plug 77 Instructions for the user GB IE 4 USING THE HOB 4 1 Lighting the hob burners Before lighting the hob burners check that the flame spreader crowns are correctly in place with their respective burner caps making sure that the holes A in the flame spreaders are aligned with the igniters and thermocouples T
11. by the applicable standards When the job is complete the installer must issue a certificate of conformity Instructions for the installer GB IE 6 6 Gas connection Connection to the gas supply network can be made using a rigid copper hose or a flexible steel hose with a continuous wall and in compliance with the guidelines established by the applicable standard Once the operation is complete check the hose fittings for leaks using a soapy solution never use a flame The hob is preset for natural gas G20 2H at a pressure of 20 mbar To set it up for supply using other types of gas see 3 ADAPTATION TO DIFFERENT TYPES OF GAS The gas inlet connection is threaded 12 external gas ISO 228 1 Connection with a rigid copper hose The connection to the gas supply network must be made in such a way that it does not cause stresses of any type on the appliance The connection can be made using the adapter unit D with double cone always G inserting gasket C provided in between Connection with a flexible steel hose Use only continuous wall stainless steel hoses that comply with current E legislation making sure to always insert the supplied gasket C between the connection A and the flexible hose B Installation with the flexible hose must be carried out so that the length of the piping does not exceed 2 metres when fully extended make sure that the hoses do not come into contact with mov
12. e manufacturer cannot be held liable for damage to persons or things caused by failure to observe the above instructions by interference with any part of the appliance or by the use of non original spare parts 25 GB IE 26 Instructions for disposal 3 ENVIRONMENTAL RESPONSIBILITY 3 1 Our environmental responsibility Pursuant to Directives 2002 95 EC 2002 96 EC and 2003 108 EC relating to the reduction of the use of hazardous substances in electrical and electronic appliances as well as to the disposal of refuse the crossed out bin symbol on the appliance indicates that at the end of the useful life of the product it must be collected separately from other refuse Therefore at the end of the product s working life the user must deliver it to the appropriate differentiated collection centres for electrical and electronic waste or deliver it back to the retailer when purchasing an equivalent product on a one for one basis Adequate differentiated collection for the subsequent forwarding of the decommissioned product to recycling processing and ecologically compatible disposal contributes to avoiding possible negative effects on the environment and on health and promotes recycling of the appliance s constituent materials Illicit disposal of the product by the user will lead to the application of administrative sanctions The product does not contain substances in quantities sufficient to be considered hazardous to he
13. ement must be carried out be a specialised technician who must carry out the network connection following the diagram below L brown N blue D yellow green The manufacturer cannot be held liable for damage to persons or things caused by non observance of the above directions or by interference with any part of the appliance 33 fr 3 fa of AS foot 34 Instructions for the installer 6 4 Ventilation in the premises The room containing the appliance should have a permanent air supply in accordance with the standards in force The room where the appliance is installed must have enough air flow needed for the regular combustion of gas and the necessary air change in the room itself The air vents protected by grills must be the right size to comply with current regulations and positioned so that no part of them is obstructed not even partially The room must be kept adequately ventilated in order to eliminate the heat and humidity produced by cooking in particular after prolonged use you are recommended to open a window or to increase the speed of any fans 6 5 Extraction of the combustion products Combustion products must be extracted by means of hoods connected to a natural draught chimney whose efficiency is assured or via forced extraction An efficient extraction system requires precision planning by a specialist qualified in this area and must comply with the positions and distances indicated
14. he burner controlled by each knob is shown next to the knob The appliance is equipped with an electrical ignition device e Simply press the knob and turn it anti clockwise to the a maximum flame symbol iN until the burner lights WZ On valved models once the burner is lit keep the knob pressed for a few seconds to give the thermocouple time to heat up The burner may go out when the knob is released in this case the thermocouple has not heated up sufficiently Wait a few moments and repeat the operation keeping the knob pressed for longer This is not necessary on burners that are not equipped with a thermocouple Once the burner is lit the flame can be adjusted as required Always check that the control knobs are in the O off position when you finish using the hob If the burners should go out accidentally after about 20 seconds a safety device will be tripped cutting off the gas supply even if the gas tap is open Turn off the control knob and wait at least 1 minute before trying to re light the burner 27 GB lE 2222 jo A 28 Instructions for the user Nd 4 2 Practical tips for using the burners For better burner efficiency and to minimise gas consumption use pans with a flat smooth base and a lid that have a suitable size for the burner thus preventing the flames reaching the sides of the pan see paragraph 4 3 Pan Diameter Once the contents come to the boil turn down the flame
15. ication of gas taps be Over time the gas taps may become difficult to turn and get blocked Clean them internally and replace the lubrication grease This procedure must be carried out by a specialised technician 38
16. ing parts and that they are not crushed in any way 6 7 Connection to liquid gas Use a pressure regulator and make the connection on the gas cylinder following the guidelines set out in the regulations in force Make sure that the supply pressure complies with the values indicated in the table shown in the paragraph 7 2 Burner and nozzle characteristics table 35 Instructions for the installer 7 ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations disconnect the appliance from the power supply The appliance is preset for natural gas G20 2H at a pressure of 20 mbar In the case of operation with other types of gas the burner nozzles must be changed and the minimum flame adjusted on the gas taps To change the nozzles proceed as described in the following paragraphs 7 1 Replacement of the cooking hob nozzles 1 Extract the pan racks and remove all the caps and flame spreader crowns 2 Unscrew the burner nozzles with a 7 mm socket spanner 3 Proceed with the replacement of the burner nozzles according to the gas to be used see paragraph 7 2 Burner and nozzle characteristics table 4 Replace the burners in the correct position The nozzles for using city gas G110 8 mbar are available from authorised S7 service centres 36 Instructions for the installer 7 2 Burner and nozzle characteristics table Ultra rapid 3 1600 Auxiliary 1 Auxiliary
17. ll Oo i U ll pus f o nm o Lo TE a 556 586 Max 150 mm IMPORTANT if the appliance is mounted on a unit make sure that a separating shelf is installed as shown in the figure However if the appliance is on an oven installed under the hob there is no need to install a separating shelf If installed on top of an oven the latter must be equipped with a cooling fan 32 Instructions for the installer else 6 3 Electrical connection _ Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing Do not remove this plate for any reason The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations Make sure that the supply line is suitably earthed Fit power line with an omnipolar circuit breaker with a contact opening gap equal to or greater than 3 mm in an easily accessible position close to the hob Avoid the use of adapters and shunts no less than 0 75 mm2 3 x 0 75 cable If the power cable is replaced the cross LL N section of wires in the new cable must be CE remembering that the end for connection to the appliance must have a longer earth 20 mm wire yellow green longer by at least 20 mm Only use a HO5V2V2 F or similar resistance cable to the maximum temperature of 90 C Its replac
Download Pdf Manuals
Related Search