Smart Inventions HAWM-UX/UF User's Manual
Contents
1. 100V 240V 50 Hz 60 Hz 39 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Number Function 1 3 5 mm audio output connector recommended for SBA L speakers 4 pin power mini DIN 5V 2A connector reserved for ECP harness cable 7 pin mini DIN connector reserved for ECP harness cable 3 5 mm audio input connector reserved for WMB HD DB15 VGA 2 input connector reserved for WMB RCA jack composite video input reserved for ECP harness cable OJIN RCA jack audio left right input reserved ECP harness cable Using the SMART UX60 projector ECP for HAWM UX UF mounted components The following diagram and list identify the ECP ports that connect to HAWM UX UF mounted components Number Function 1 USB B jack reserved for WMB To connect your projector s ECP harness cable 40 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Number Function 2 USB A jack recommended location for interactive whiteboard USB cable 3 DB15 ECP connector reserved for ECP harness cable Connecting your SMART UX60 projector s ECP harness cable The ECP harness cable controls all signals and commands sent between the ECP and the projector Choose a side of the interactive whiteboard to install your ECP on and then follow the instructions in the SMART Board 685ix and D685ix Inte2. Number Function 1 RCA jack audio left right input reserved for S video input S video input connector 3 5 mm audio output connector reserved for VGA 2 In connector HD DB15 VGA 2 connector 3 5 mm audio output connector reserved for VGA 1 In connector HD DB15 VGA 1 connector VGA output Power socket olol NI oO a AJ OJN RS 232 connector RJ45 jack for network connections 60 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF NOTE SMART recommends that you use a VGA out connector on your source input to simplify the cable placement Using the SMART UF65 and SMART UF65w projector ECP for other components The following diagram and list identify the ECP connections to components that aren t mounted to the HAWM UX UF Number Function 1 USB A jack for peripheral device connection USB A jack for peripheral device connection USB B tethered jack for computer connection USB A jack for peripheral device connection USB A jack for peripheral device connection RCA jack composite video input for peripheral device connection BY OJIN RCA jack audio left right input for peripheral device connection To connect your projector power cable on the HAWM UX UF 61 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF Connecting the power ne
3. Taut cable 5 Bundle the excess cable making sure that there is a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable 54 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF Placing cables for HAWM UX UF mounted components To prevent cable friction SMART recommends that you first place the cables that don t shift after they re installed Cables that connect components mounted to the HAWM UX UF don t shift after they re installed To prevent cable friction SMART recommends that you place these cables first Using the SMART UF65 and SMART UF65w projector connection panel for HAWM UX UF mounted components The following diagram and list identify the SMART UF65 and SMART UF65w projector connections to HAWM UX UF mounted components To access the projector connection panel and wire management clip remove the input output cover on the left side of the projector and remove the cable covers For more information see the SMART Board 600i4 and D600i4 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 146184 100V 240 50 Hz 60 Hz xS Number Function 1 4 pin power mini DIN 5V 2A connector reserved for ECP harness cable 7 pin mini DIN connector reserved for ECP harness cable RCA jack composite video input reserved for ECP harness cable
4. 69 Introduction The SMART Board 600i3 or D600i3 interactive whiteboard systems include a SMART UF55 high offset projector or SMART UF55w high offset widescreen projector and an extended control panel ECP that s remotely located IMPORTANT Before following these instructions install your HAWM UX UF and interactive whiteboard system according to the SMART HAWM UX UF Installation Guide smarttech com kb 145745 The instructions below are a supplement to and not a substitute for the installation guide To mount the mobility switch 66 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF Mounting your HAWM UX UF mobility switch The mobility switch controls the vertical movement of the HAWM UX UF and your interactive whiteboard system The mobility switch is wired directly to the rear panel of the HAWM UX UF Use the installation guide with the following procedure to place and mount the mobility switch 1 Locate the HAWM UX UF mobility switch and then remove and discard the plastic bag that holds the mobility switch 2 Choose the mobility switch s mounting location There are mounting holes on the left and the right sides and near the top and the bottom of the interactive whiteboard NOTE If you have installed or plan to install the SBA or SBA L projection audio system mount the mobility switch on the bottom mounting holes 67 CHAPTER 6 C
5. 21 Mounting your HAWM UX UF mobility switch eene 22 Placing cables for HAWM UX UF mounted components 24 Placing cables for other 30 Cabling 685ix or D685ix system to HAWM UX UF 35 RR 35 Mounting your HAWM UX UF mobility switch eene 36 Placing cables for HAWM UX UF mounted components 38 Placing cables for other 45 Cabling 600i4 D600i4 system to 51 MOD UCU OM E 51 Mounting your HAWM UX UF mobility switch eene 52 CONTENTS Placing cables for HAWM UX UF mounted components 54 Placing cables for other 58 6 Cabling a 600i3 or D600i3 system to a 65 65 Mounting your HAWM UX UF mobility switch eene 66 Placing cables for remotely mounted components 68 Chapter 1 Best practices for cabling your HAWM UX UF ITROGUCTION 1 Best practices for 1 Cust
6. RCA jack audio left right input reserved for ECP harness cable BR wl 3 5 mm audio output connector recommended for SBA L speakers 55 CHAPTER 5 CABLING A 60014 060014 SYSTEM TO A HAWM UX UF Using the SMART UF65 and SMART UF65w projector ECP for HAWM UX UF mounted components The following diagram and list identify the ECP ports that connect to HAWM UX UF mounted components Number Function 1 USB B jack reserved for the primary computer 2 DB15 ECP connector reserved for ECP harness cable Connecting your SMART UF65 or SMART UF65w projector s ECP harness cable The ECP harness cable controls all signals and commands sent between the ECP and the projector Choose a side of the interactive whiteboard to install your ECP on and then follow the instructions in the SMART Board 600i4 and D600 4 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 146 184 To connect your projector s ECP harness cables 56 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF 1 Pass the ECP cable through the cable slot NOTE The upper part of the ECP cable is too thick to fit inside the cable slot so put the thinner part of the ECP cable in the cable slot From the ECP harness cable attach the composite video RCA jack its associated dual channel audio input two RCA jacks the 4 pin power mini DIN connector and the 7 pi
7. aroom control device a network cable projector s power cable When connecting these peripheral devices make sure there s enough slack mount the peripheral device to a permanent location and make sure there are no obstructions in the cable path Cable friction rubbing and strain can occur if you don t take the proper precautions Mounting and connecting your SMART UF55 or SMART UF55w projector s ECP harness cable Before you mount any cables to your projector you must mount the SMART UF55 or SMART UF55w projector s ECP to the wall not to the HAWM UX UF You must carefully attach the ECP at the location specified in the instructions below Refer to your SMART Board 680i3 and 068013 Interactive Whiteboard System Installation Guide smarttech com kb 131457 and the SMART Board 600i2 and 600i3 Series Interactive Whiteboard System Extended Control Panel ECP Installation Template smarttech com kb 118881 for additional instructions NOTE You must have your interactive whiteboard placed on the HAWM UX UF before you begin this procedure The HAWM UX UF should be at its highest position before you start measuring 1 Choose a side of the interactive whiteboard to install your ECP beneath Consider the distance to your peripheral devices and inputs when making this decision 69 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF 2 Draw aline on the wall behind the interactive whiteboard on the appropriate side
8. 23 53 67 mounting peripheral devices best practice 3 movement switch 60013 interactive whiteboard 66 600i4 interactive whiteboard 52 685ix interactive whiteboard 36 800i4 interactive whiteboard 22 885ix interactive whiteboard 6 P path of travel 2 power outlets best practice for cabling 2 S SBA L Projection Audio System SMART UF55 projector 79 SMART UF65 projector 28 57 SMART UX60 projector 14 43 SMART hub SE240 60013 interactive whiteboard 68 600i4 interactive whiteboard 58 685ix interactive whiteboard 45 800i4 interactive whiteboard 30 885ix interactive whiteboard 16 SMART hub VE220 60013 interactive whiteboard 68 600i4 interactive whiteboard 58 685ix interactive whiteboard 45 800i4 interactive whiteboard 30 885ix interactive whiteboard 16 SMART Mobile Height Adjustable Floor Stand FS UX 7 SMART UF55 projector ECP for harness cable 73 ECP for remote mounted 78 for remote mounted components 77 power cable 74 SBA L audio system 79 SMART UF65 projector 57 600i4 interactive whiteboard 33 51 ECP diagram for other components 60 ECP for HAWM mounted 32 ECP for HAWM mounted components 85 INDEX 25 55 ECP for other components 32 for HAWM mounted components 24 for other components 31 59 HAWM mounted components 54 power cable 61 SBA L audio system 28 57 SMART UX60 projector 685ix interactive whiteboard 43 ECP diagram for HAWM mounted components 39 ECP for
9. recommended If you don t want to connect a network cable proceed to step 3 Otherwise make sure you have a network cable with RJ45 plugs not included long enough to connect your projector to a LAN port Pass the network cable through the boom and connect the RJ45 plug on the network cable to the RJ45 port on the projector Make sure that the network cable is in the middle left position in the cable slot Pass peripheral device cables through the boom Make sure that the peripheral device cables are in the middle left position in the cable slot Connect your peripheral device cables to the appropriate locations on the projector s connection panel see page 30 If you don t want to connect a network cable proceed to the next step Otherwise connect the RJ45 plug on the network cable to the RJ45 port on the projector making sure that the network cable is in the middle left position in the cable slot 34 10 11 12 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Place the cables around the back of the HAWM UX UF toward the left side of the interactive LS whiteboard if the peripheral device or LAN connector is HER located on the left or toward the right side of the interactive whiteboard if the peripheral device or LAN connector is located on the right Attach the cables to the lower cable clips on the HAWM If you have many cables attached smoothly bundle you
10. 36 91 4 cm from the floor using a pencil and level a Ifyou choose the left side locate the lower left hand side of the interactive whiteboard and draw a line 1 2 5 cm from the left of the interactive whiteboard This mark is for the top right screw s drill hole on the ECP 4 b If you choose the right side locate the lower right hand side of the interactive whiteboard and draw a line 1 2 5 cm from the right of the interactive whiteboard This mark is for the top left screw s drill hole on the ECP pes 3 Retrieve your ECP template and textless installation instructions from the SMART UF55 or SMART UF55w projector packaging 4 On the appropriate side make hole in the ECP template s screw hole mark 5 Place the ECP template s screw hole mark on top of the drill hole mark you created in step 2 Align the center of the screw hole to the drill hole mark Level the ECP template and tape it securely 6 Drill the ECP template at all four drill hole locations following the recommendations on the ECP template for the drill bit size Remove the ECP template from the wall when you finish drilling and discard it 70 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF Retrieve the four plastic anchors and four screws supplied for mounting the ECP from the SMART UF55 or SMART UF55w projector packaging Using a hammer drive the plastic anchor
11. Bundle the excess cable screws listed inside the HAWM UX UF installation guide Secure the cable toward the side of the interactive whiteboard where you choose to mount the mobility switch and make sure that the cable is toward the bottom of the switch as you mount it HAWM UX UF s lower cable CR clip making sure that the i cable is taut between the interactive whiteboard S the clip and loose between the clip and the base of the HAWM UX UF making sure that there is a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable Placing cables for HAWM UX UF mounted components To prevent cable friction SMART recommends that you first place the cables that don t shift after they re installed Cables that connect components mounted to the HAWM UX UF don t shift after they re installed The wire management bundle WMB shifts only if it s connected to the wall or to the guest computer 8 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Using the SMART UX60 projector connection panel for HAWM UX UF mounted components To access the projector connection panel and wire management clip remove the input output cover on the left side of the projector and remove the cable covers For more information see the SMART Board X800 ix Interactive Whiteboard System Configuration and User s Guide smarttech com kb 150502 The following diagram an
12. HAWM UX UF installation guide smarttech com kb 145745 The instructions below are a supplement to and not a substitute for the installation guide To mount the mobility switch 36 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Mounting your HAWM UX UF mobility switch The mobility switch controls the vertical movement of the HAWM UX UF and your interactive whiteboard system The mobility switch is wired directly to the rear panel of the HAWM UX UF Use the installation guide with the following procedure to place and mount the mobility switch to your interactive whiteboard 1 Locate the HAWM UX UF mobility switch and then remove and discard the plastic bag that holds the mobility switch 2 Choose the mobility switch s mounting location There are mounting holes on the left and the right sides and near the top and the bottom of the interactive whiteboard IMPORTANT If you installed or plan to install the SBA L Projection Audio System mount the mobility switch on the bottom mounting holes 37 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF 3 Secure the mobility switch cable using a Phillips No 2 screwdriver and the two screws listed inside the HAWM UX UF installation guide Secure the cable toward the side of the interactive whiteboard where you choose to mount the mobility switch and make sure that the cable is toward the bottom of the switch as you
13. HAWM mounted 9 ECP for HAWM mounted components 47 ECP for other components 18 47 for HAWM mounted components 8 for other components 17 HAWM mounted components 38 other mounted components 46 power cable 19 48 SBA L audio system 14 43 switch 60013 interactive whiteboard 66 600i4 interactive whiteboard 52 685ix interactive whiteboard 36 800i4 interactive whiteboard 22 885ix interactive whiteboard 6 U up down switch 600i3 interactive whiteboard 66 800i4 interactive whiteboard 22 885ix interactive whiteboard 6 86 Toll Free 1 866 518 6791 U S Canada aW or 1 403 228 5940 www smarttech com
14. WMB through the top cable clip you installed on the side of the HAWM UX UF To connect your projector to your speakers 43 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF 5 Connect the WMB s USB A plug to the ECP and loop the excess cable length into the cable clip 6 Use the WMB s magnetic connection to attach the WMB to a metal surface until you need to attach a guest computer to it IMPORTANT If you attach the WMB s anchor point to the wall make sure the anchor point is set to a distance so that the WMB does not slip off the anchor point when the HAWM UX UF is moving or make sure the WMB has a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable Connecting the SMART UX60 projector to the SBA L projection audio system The HAWM UX UF is designed to accommodate mounting the SBA L projection audio system directly to the interactive whiteboard That way when the speakers rise and descend with the HAWM UX UF s and interactive whiteboard s movement there s less risk of damage to the audio connection and power cables Therefore SMART recommends that you don t mount the SBA L projection audio system to the wall Before connecting the audio system to the projector you must install the speaker brackets speakers and speaker cable clips according to the SBA L Projection Audio System Installation Instructions smarttech com kb 142552 1 Retrieve the 3 5
15. and audio input on your computer s video output connector Using the SMART UF55 and SMART UF55w projectors ECP for remotely mounted components The following diagram and list identify the SMART UF55 and SMART UF55w projectors connections to components that don t mount to the HAWM UX UF Number Function 1 RS 232 connector HD DB15 VGA connector 3 5 mm audio output connector reserved for VGA connector RCA jack audio left right input reserved for S video connector RCA jack composite video input connector 2 3 4 S video input connector 5 6 7 RCA jack audio left right input reserved for composite video connector To connect a composite video device 79 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF Connecting peripheral devices to your SMART UF55 and SMART UF55w projectors ECP temporarily To connect a DVD Blu ray player VCR document camera digital camera or other visual or audio visual peripheral device you must connect the device s video and audio outputs to the ECP You can have up to three peripheral devices and a host computer connected at one time The SMART UF55 and SMART UF55w projectors ECP has three video inputs and one communications port an HD DB15 with associated 3 5 mm audio jack an S Video jack with associated dual channel audio RCA jacks a composite video RCA jack with associated dual channel audio RCA jacks and one RS 232 connector d
16. connection panel for other components The following diagram and list identify the projector connection panel connections to components that don t mount on the HAWM UX UF eee DC 5V 2A OG Number Function 1 HD DB15 VGA Out output connector S video input connector RCA jack audio left right input reserved for S video input connector RJ45 jack for network connections 2 3 4 5 HD DB15 VGA 1 input connector computer analog signal component video input HDMI connector input Power socket 18 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF fg NOTES SMART recommends that you use a VGA out connector on your source input to simplify the cable placement HDMI connector is intended for non interactive audio video content only such as high definition DVD Blu ray players If you connect a cable from the HDMI port to a computer your SMART Board interactive whiteboard doesn t recognize touch commands Using the SMART UX60 projector ECP for other components The following diagram and list identify the ECP connections to components that aren t mounted to the HAWM UX UF Number 1 Function USB A jack for USB drives Powe
17. device cables on the HAWM UX UF 33 CHAPTER 3 CABLING AN 88014 OR 88514 SYSTEM TO HAWM UX UF 1 Pass the power ep LL I LE cable through the gt boom and then connect it to the Cable slot power socket Make sure that the power cable is in the far right position in the cable slot Place the power cable around the back of the HAWM UX UF toward the left side of the interactive whiteboard if the power outlet is located on the left or toward the right side of the interactive whiteboard if the power outlet is located on the right Connect the other end of the power cable to a power outlet no more than 72 183 cm away from the projector This distance includes the amount of slack you need for the projector s range of movement If necessary use a power cable extension of an appropriate length that includes a minimum of 28 71 1 cm excess Straight length or a 14 35 6 cm loose loop of cable Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cable isn t taut at any range of the HAWM UX UF s movement TIP Find a support location for the power cable that doesn t interfere with the movement of the HAWM UX UF and attach a cable management clip not included to the cable Make sure that you have enough slack for the HAWM UX UF to move freely and then bundle the excess This is strongly
18. extended control panel ECP or interactive whiteboard are long enough to accommodate the additional distances your HAWM UX UF requires You might need longer cables to attach your interactive whiteboard system to your computer and to other peripherals Before customizing or buying cables assess your installation location and follow these best practices for customizing your cabling to your peripheral devices Carefully measure the distance between your devices and their connection locations on the interactive whiteboard system Measure the distances at the HAWM UX UF s lowest and highest height and use the longest distance as your minimum cable length sure there s enough slack in your cables to minimize cable strain e When measuring the minimum cable length make sure there are no obstructions in the cable s path A rising or descending cable can catch on an obstruction unless the cable is properly secured out of the way of the obstruction Chapter 2 Cabling an 885ix system to a HAWM UX UF Introduction rere 5 Mounting your HAWM UX UF mobility switch enne 6 Placing cables for HAWM UX UF mounted components 7 Placing cables for other 13 Introduction SMART Board 885ix interactive whiteboard systems always include a SMART UX60 ultra short th
19. include the following e your computer or SMART Hub VE220 or SE240 collaboration platform NOTE Both the VE220 and SE240 models include 72 183 cm output cables for connecting to your projector Cable extensions not included may be required aroom control device a network cable projector s power cable Other projector to input device connections such as DVD Blu ray player using HDMI or S video connections When connecting these peripheral devices make sure there s enough slack mount the peripheral device to a permanent location and make sure there are no obstructions in the cable path Cable friction rubbing and strain can occur if you don t take the proper precautions 46 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Using the SMART UX60 projector connection panel for other components The following diagram and list identify the projector connection panel connections to components that don t mount to the HAWM UX UF DC 5V 2A _ oo Ge Number Function 1 HD DB15 VGA Out output connector S video input connector RCA jack audio left right input reserved for S video input connector 3 5 mm audio input connector reserved for VGA 1 conne
20. mount it 4 Place the cable through the HAWM UX UF s lower cable clip making sure that the cable is taut between the interactive whiteboard and the clip and loose between the clip and the base of the HAWM UX UF Taut cable 5 Bundle the excess cable making sure that there is a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable 38 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Placing cables for HAWM UX UF mounted components To prevent cable friction SMART recommends that you first place the cables that don t shift after they re installed Cables that connect components mounted to the HAWM UX UF don t shift after they re installed The wire management bundle WMB shifts only if its connected to the wall or to a guest computer Using the SMART UX60 projector connection panel for HAWM UX UF mounted components To access the projector connection panel and wire management clip remove the input output cover on the left side of the projector and remove the cable covers For more information see the SMART Board 685ix and D685ix Interactive Whiteboard System Configuration and User s Guide smarttech com kb 137396 The following diagram and list identify the projector s connections to HAWM UX UF mounted components
21. outlets or cable locations If a power outlet or cable crosses the HAWM UX UF s path of travel a power supply can break or a cable an be damaged If you need to attach a peripheral device guest computer or laptop to the interactive whiteboard system make sure that the cable is long enough so that at this highest or lowest height the HAWM UX UF doesn t pull the laptop or peripheral 1 3 CHAPTER 1 BEST PRACTICES FOR CABLING YOUR HAWM UX UF Mount your peripheral devices to a permanent location near the HAWM UX UF If the peripheral device moves or can move it can cause cable strain if the device is moved too far from and interferes with the HAWM UX UF Before placing cables note the height and location of cable access points such as cable tray access hatches ethernet ports and power outlets and restrictions in the room and note alternative routing options If you can move the HAWM UX UF closer to these access points al WARNING To prevent a tripping hazard bundle excess cabling or use cable ties and cable management clips to secure the cables above floor level 4 CHAPTER 1 BEST PRACTICES FOR CABLING YOUR HAWM UX UF Customizing your cables Cables supplied by SMART for connecting your projector to the
22. plug on the network cable to the RJ45 port on the projector Make sure that the network cable is in the middle left position in the cable slot Secure the cables to the SMART UF55 or SMART UF55w projector s wall mount bracket using a cable tie Place the cables through the cable cutouts on the bottom wall mount bracket Place the harness cable around the back of the HAWM UX UF toward the left side of the interactive whiteboard if the ECP is mounted on the left or toward the right side of the interactive whiteboard if the ECP is mounted on the right If you have many cables attached smoothly bundle your peripheral device cables together ES using a cable tie not included 76 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF 9 Attach a cable management clip not included to the cables or cable bundles making sure there s a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable 10 If you don t want to connect a network cable proceed to the next step Otherwise connect the other end of the network cable to your LAN port 11 Connect the HD DB15 VGA connector and the DB25 connector from the harness cable to the ECP 12 Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cables aren t taut at any range of the HAWM UX UF s movement If they re still taut re
23. switch 2 Choose the mobility switch s mounting location There are mounting holes on the left and the right sides and near the top and the bottom of the interactive whiteboard IMPORTANT If you installed or plan to install the SBA L projection audio system mount the mobility switch on the bottom mounting holes 7 23 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF 3 Secure the mobility switch cable toward the side of the interactive whiteboard where you choose to mount the mobility switch using a Phillips No 2 screwdriver and the two screws listed inside the HAWM UX UF installation guide Make sure that the cable is toward the bottom of the switch as you mount it AY li 4 Placethe cable through the HAWM UX UF s lower cable clip making sure that the cable is taut between the interactive whiteboard and the clip and loose between the clip and the base of the HAWM UX UF 5 Bundle the excess cable making sure that there is a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable 24 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Placing cables for HAWM UX UF mounted components To prevent cable friction SMART recommends that you first place the cables that don t shift after they re installed Cables that connect components mounted to the HAWM UX UF don
24. tray 1 Connect the ends of the stereo Y cable to the VGA 1 and the VGA 2 inputs your UF65 or UF65w projector 2 Connect the other end of the stereo Y cable to the audio jack on the back of your interactive whiteboard s pen tray Connecting your SMART UF65 or SMART UF65w projector to the SBA L projection audio system HAWM UX UF is designed to accommodate mounting the SBA L projection audio system directly to the interactive whiteboard That way when the speakers rise and descend with the HAWM UX UF s and interactive whiteboard s movement there s less risk of damage to the audio connection and power cables Therefore SMART recommends that you don t mount the SBA L projection audio system to the wall Before connecting the audio system to the projector you must install the speaker brackets speakers and speaker cable clips according to the SBA L Projection Audio System Installation Instructions smarttech com kb 142552 1 Retrieve the 3 5 mm jack to dual channel audio output two RCA jacks cable from the SBA L packaging 2 Pass the audio connection cable through the boom Place the cables in the left side of the cable slot 3 Connect the audio connection cable to the projector s connection panel 29 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF 4 Place the audio connection cable through the right speaker cable clip the rear of the interactive whiteboard toward the right T spe
25. your peripheral devices 13 Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cables aren t taut at any range of the HAWM UX UF s movement If it s still taut repeat this procedure until you find a suitable mounting location or length for the cables Connecting composite video and USB devices to your projector s ECP The ECP has three USB A jacks and one composite video RCA jack with associated dual channel audio RCA jacks SMART recommends that you install only small USB devices such as a USB drive or that you use a USB port on your computer for larger devices to eliminate the risk of cable damage SMART also recommends that you use the composite video connector for temporary connections to peripheral devices or that you use a permanent connection to the projector s connection panel 1 Make sure that you place the device near the HAWM UX UF on a stable support 2 Allow enough excess cable length to accommodate the HAWM UX UF s rise and descent or make sure that the HAWM UX UF isn t moved while the device is attached 3 When your e finished with the device disconnect the cable from the ECP 64 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF Chapter 6 Cabling a 60013 or 060013 system to a HAWM UX UF Introduction Lm 67 Mounting your HAWM UX UF mobility switch eene 67 Placing cables for remotely mounted components
26. 0014 SYSTEM TO HAWM UX UF Mounting your HAWM UX UF mobility switch The mobility switch controls the vertical movement of the HAWM UX UF and your interactive whiteboard system The mobility switch is wired directly to the rear panel of the HAWM UX UF Use the installation guide with the following procedure to place and mount the mobility switch 1 Locate the HAWM UX UF mobility switch and then remove and discard the plastic bag that holds the mobility switch 2 Choose the mobility switch s mounting location There are mounting holes on the left and the right sides and near the top and the bottom of the interactive whiteboard ic IMPORTANT If you installed or plan to install the SBA L Projection Audio System mount the mobility switch on the bottom mounting holes 53 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM A HAWM UX UF 3 Secure the mobility switch cable toward the side of the interactive whiteboard where you choose to mount the mobility switch using a Phillips No 2 screwdriver and the two screws listed inside the HAWM UX UF installation guide Make sure that the mobility switch cable is toward the bottom of the switch as you mount it 4 Placethe cable through the HAWM UX UF s lower cable clip making sure that the cable is taut between the interactive whiteboard and the clip and loose between the clip and the base of the HAWM UX UF
27. 3 OR D60013 SYSTEM TO A HAWM UX UF Place the audio connection cable through the right speaker cable clip on the rear of the interactive whiteboard toward the right speaker Connect the dual channel audio output to the speaker s connection panel and bundle any excess cable in the right speaker cable clip Retrieve the speaker to speaker Molex double barreled cable from the SBA L packaging Place the Molex cable through the left speaker cable clip through the space between the HAWM UX UF and the interactive whiteboard Place the Molex cable through the right speaker cable clip Connect the Molex cable to both speakers Bundle any excess cable in the left speaker cable clip Right speak cable clip er Left speaker cable clip 82 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF Index Numerics 600i3 interactive whiteboard host computer to projector 77 network cable connection 74 SMART hub VE220 and SE240 68 SMART UF55 projector power cable 74 temporary connections 79 60014 interactive whiteboard 51 mobility switch 52 network cable 62 peripheral cables 62 SMART hub VE220 and SE240 58 SMART UF65 projector power cable 61 temporary connections 63 685ix interactive whiteboard cabling 35 ECP 74 mobility switch 36 network cable 48 peripheral device 48 SMART Hub VE220 and SE240 45 SMART UX60 projector power cable 48 tempo
28. ABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF 3 Secure the mobility switch cable toward the side of the interactive whiteboard where you choose to mount the mobility switch using a Phillips No 2 screwdriver and the two screws listed in the HAWM UX UF installation guide Make sure that the mobility switch cable is toward the bottom of the switch as you mount it 4 Placethe cable through the HAWM UX UF s lower cable clip making sure that the cable is taut between the interactive whiteboard and the clip and loose between the clip and the base of the HAWM UX UF Taut cable 5 Bundle the excess cable making sure that there s a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable To mount your projector s ECP harness cable 68 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF Placing cables for remotely mounted components Cables for peripheral devices connected to the projector but not mounted on the HAWM UX UF are at the greatest risk of damage because they shift as the HAWM UX UF rises and descends These peripheral devices and cables include the following e your ECP harness cable your computer or SMART Hub VE220 or SE240 collaboration platform NOTE Both the VE220 and SE240 models include 72 183 cm output cables to connect to your projector You might need cable extensions not included may be required
29. Function 1 USB A jack for USB drives Power button and status new Volume control Two mini USB B jacks connect to computers 1 and 2 11 pin connector connects to ECP harness cable 2 3 4 Input selection 5 6 7 4 pin connector for room control 26 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Connecting your SMART UF65 or SMART UF65w projector s ECP harness cable The ECP harness cable controls all signals and commands sent between the ECP and the projector Choose a side of the interactive whiteboard to install your ECP on and then follow the instructions in the SMART Board 88014 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 150699 To connect your 1 Pass the ECP cable through the projector s ECP harness cable slot cables The upper part of the ECP cable is too thick to fit inside the cable slot so put the ce s thinner part of the ECP cable prm SN in the cable slot ji oe 2 From the ECP harness cable attach the DB9 connector the 4 pin power mini DIN connector and the 7 pin mini DIN 4 connector to the projector s m SSS 3 Attach the screw the ECP Em strain relief to the projector housing using a Phillips No 2 screwdriver 4 Place the harness cable around the bac
30. M UX UF are at the greatest risk of damage because they shift as the HAWM UX UF rises and descends These peripheral devices and cables include the following your computer or SMART Hub VE220 or SE240 collaboration platform NOTE Both the VE220 and SE240 models include 72 183 cm output cables for connecting to your projector You might need cable extensions not included aroom control device anetwork cable the projector s power cable e other projector to input device connections such as a DVD Blue ray player using S video connections When connecting these peripheral devices make sure there s enough slack mount the peripheral device to a permanent location and make sure there are no obstructions in the cable path Cable friction rubbing and strain can occur if you don t take the proper precautions 59 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF Using the SMART UF65 and SMART UF65w projector connection panel for other components Remove the input output cover on the left side of the projector and the cable covers to access the projector connection panel and wire management clip For more information see the SMART Board 600i4 and 060014 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 1461984 The following diagram and list identify the SMART UF65 and SMART UF65w projector s connections to components that don t mount on the HAWM UX UF
31. SMART Height Adjustable Wall Mount HAWM UX UF Integration and Cabling Guide For SMART Board 600 and 800 interactive whiteboard projector systems Extraordinary made simple SMART Product Registration If you register your SMART product we ll notify you of new features and software upgrades Register online at www smarttech com registration Keep the following information available in case you need to contact SMART Technical Support Serial Number Date of Purchase FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instructions may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Trademark Notice SMART Board SMART Hub smarttech the SMART logo and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U S and or other countries Molex is a registered trademark of Molex its affiliates related companies licensor
32. T UX60 projector to the wire management bundle WMB SMART recommends that when the WMB isn t in use you use the WMB s magnetic connection to attach the WMB to the HAWM UX UF s moving frame By doing so you prevent the WMB from shifting as the HAWM UX UF rises and descends CAUTION When attaching a guest computer or laptop to the projector system make sure that it is not pulled by the HAWM UX UF at its lowest or highest height NOTE If you choose to connect the WMB to the wall mounted magnetic clip do so at a height and location that doesn t interfere with the HAWM UX UF s movement 1 Connect the WMB to the projector by attaching the HD DB15 connector and the 3 5 mm audio jack to the projector s connection panel see page 38 NOTE The USB A plug doesn t connect to the projector s connection panel 42 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF 2 Place the WMB through the cable management clip located under the projector Make sure the WMB s strain relief sits above the clip point 3 Ifthe ECP is mounted on the left place the WMB around the back of the HAWM UX UF s interactive whiteboard brackets toward the left side of the interactive whiteboard If the ECP is mounted on the right place the WNMB around the back of the HAWM UX UF s interactive whiteboard brackets toward the right side of the interactive whiteboard 4 Place the
33. TER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Chapter 3 Cabling an 88014 or 88514 system to a HAWM UX UF 9 oio EE 24 Mounting your HAWM UX UF mobility switch 24 Placing cables for HAWM UX UF mounted components 26 Placing cables for other 35 Introduction The SMART Board 880i4 and 885i4 interactive whiteboard systems include a SMART UF65 high offset projector or SMART UF65w projector high offset widescreen projector both with a 3D projection option and an extended control panel ECP that s located on the interactive whiteboard IMPORTANT Before following these instructions install your HAWM UX UF and interactive whiteboard system according to the SMART HAWM UX UF Installation Guide smarttech com kb 145745 The instructions below are a supplement to and not a substitute for the installation guide To mount the mobility switch 22 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Mounting your HAWM UX UF mobility switch The mobility switch controls the vertical movement of the HAWM UX UF and your interactive whiteboard system The mobility switch is wired directly to the rear panel of the HAWM UX UF Use the installation guide with the following procedure to place and mount the mobility switch 1 Locate the HAWM UX UF mobility switch and then remove and discard the plastic bag that holds the mobility
34. ace the Molex cable through the right speaker cable clip 8 Connect the Molex cable to both speakers and bundle any excess cable in the left speaker cable clip CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Right speaker cable clip Left speaker 16 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Placing cables for other components Cables for peripheral devices connected to the projector but not mounted on the HAWM UX UF are at the greatest risk of damage because they shift as the HAWM UX UF rises and descends These peripheral devices and cables include the following e your computer or SMART Hub VE220 or SE240 collaboration platform NOTE Both the VE220 and SE240 models include 72 183 cm output cables to connect to your projector You might need cable extensions not included e aroom control device connects to the ECP with a 4 pin accessory cable e anetwork cable the projector s power cable NOTES For temporary connections connect peripheral devices such as a DVD Blu ray player to the SMART Board 800ix interactive whiteboard system s ECP e Mount the peripheral device to a permanent location and check cabling to ensure there s enough slack and that there are no obstructions in the cable path Cable friction rubbing and strain can occur if you don t take the proper precautions 17 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Using the SMART UX60 projector
35. aker Right speaker cable clip 5 Connect the dual channel audio output to the speaker s connection panel and bundle any excess cable in the right speaker cable clip 6 Retrieve the speaker to speaker Molex double barreled cable from the SBA L packaging 7 Place the Molex cable through the left speaker cable clip through the i space between the HAWM UX UF and the interactive whiteboard i Left speaker cable clip 8 Place the cable through the right speaker cable clip 9 Connect the Molex cable to both speakers and bundle any excess cable in the left speaker cable clip 30 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Placing cables for other components Cables for peripheral devices connected to the projector but not mounted on the HAWM UX UF are at the greatest risk of damage because they shift as the HAWM UX UF rises and descends These peripheral devices and cables include the following your computer or SMART Hub VE220 or SE240 collaboration platform NOTE Both the VE220 and SE240 models include 72 183 cm output cables to connect to your projector You might need cable extensions not included aroom control device anetwork cable the projector s power cable NOTES For temporary connections connect peripheral devices such as DVD Blu ray player to the SMART Board 800ix interactive whiteboard system s ECP M
36. amage SMART also recommends that you use the composite video connector only for temporary connections to peripheral devices or that you use a permanent connection to the projector s connection panel 1 Make sure that you place the device near the HAWM UX UF on a stable support Allow enough excess cable length to accommodate the HAWM UX UF s rise and descent or make sure that the HAWM UX UF isn t moved while the device is attached 3 When yourre finished with the device disconnect the cable from the ECP Chapter 5 Cabling a 600i4 or D600i4 system to a HAWM UX UF Introduction Em 53 Mounting your HAWM UX UF mobility switch 53 Placing cables for HAWM UX UF mounted components 55 Placing cables for other 60 Introduction SMART Board 600i4 and D600i4 interactive whiteboard systems include a SMART UF65 high offset projector or SMART UF65w high offset widescreen projector both with a 3D projection option and an extended control panel ECP that s located on the interactive whiteboard IMPORTANT Before following these instructions install your HAWM UX UF and interactive whiteboard system according to the SMART HAWM UX UF installation guide smarttech com kb 145745 The instructions below are a supplement to and not a substitute for the installation guide To mount the mobility switch 52 CHAPTER 5 CABLING A 60014 OR 06
37. ard if the power outlet is located on the right Connect the other end of the power cable to a power outlet no more than 72 183 cm away from the projector This distance includes the amount of slack you need for the projector s range of movement If necessary use a power cable extension of an appropriate length that includes a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure that the cable isn t taut at any range of the HAWM UX UF s movement g Find a support location for the power cable that doesn t interfere with the movement of the HAWM UX UF and attach a cable management clip not included to the cable Make sure that you have enough slack for the HAWM UX UF to move freely and then bundle the excess This is strongly recommended If you don t want to connect a network cable proceed to step 3 Otherwise make sure you have a network cable with RJ45 plugs not included long enough to connect your projector to a LAN port Connect the RJ45 plug on the network cable to the RJ45 port on the projector Make sure that the network cable is in the middle left position in the cable slot Connect your peripheral device cables to the appropriate locations on the projector s connection panel Place all cables through the foam padded section of the cable clip located under the projector Increase the lengt
38. ard the left side of the interactive whiteboard for proximity to the ECP Place the WMB through the top cable clip you installed on the side of the HAWM UX UF Connect the WMB s USB plug to ia the ECP and then loop the excess L p cable length into the cable clip RCA ECP connector pod Use the WMB s magnetic connection to attach the WMB to a metal surface until you need to attach a guest computer to it IMPORTANT If you attach the WMB s anchor point to the wall make sure the anchor point is set to a distance so that the WMB does not slip off the anchor point when the HAWM UX UF is moving or make sure the WMB has a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable The RCA connector pod includes three RCA jacks for input only two dual channel fpr audio input and one for composite video input You can use the RCA connector pod to connect DVD Blu ray players and similar devices Don t connect the projection audio system SBA L speakers to the RCA connector pod Connecting peripheral devices to the RCA connector pod The RCA connector pod enables you to connect DVD Blu ray players and other devices to your interactive whiteboard system using the three RCA jacks The composite video connector and associated dual channel audio inputs on the RCA connector pod are for input only SMART recommends that you use the RCA connector pod for temporary conn
39. audio system to the projector you must install the speaker brackets speakers and speaker cable clips according to the SBA L Projection Audio System Installation Instructions smarttech com kb 142552 1 Retrieve the 3 5 mm jack to dual channel audio output two RCA jacks cable from the SBA L packaging 2 Pass the audio connection cable through the boom Place the cables in the left side of the cable slot 3 Connect the audio connection cable to the projector s connection panel 4 Place the audio connection cable through the right speaker cable clip on the rear of the interactive whiteboard toward the right speaker Right speaker cable clip 5 Connectthe dual channel audio output to the speaker s connection panel and bundle any excess cable in the right speaker cable clip 6 Retrieve the speaker to speaker Molex double barreled cable from the SBA L packaging 58 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF 7 Place the Molex cable through the left speaker cable clip through the space between the HAWM UX UF and the interactive whiteboard Left speaker cable clip 8 Place the cable through the right speaker cable clip 9 Connect the Molex cable to both speakers and bundle any excess cable in the left speaker cable clip Placing cables for other components Cables for peripheral devices connected to the projector but not mounted on the HAW
40. ctor 2 3 4 RJ45 jack for network connections 5 6 HD DB15 VGA 1 input connector computer analog signal component video input N RS 232 connector 8 HDMI connector input 9 Power socket 47 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF fj NOTES SMART recommends that you use a VGA out connector on your source input to simplify the cable placement HDMI connector is intended for non interactive audio video content only such as high definition DVD Blu ray players If you connect a cable from the HDMI port to a computer your SMART Board interactive whiteboard doesn t recognize touch commands Using the SMART UX60 projector ECP diagram for other components The following diagram and list identify the ECP connections to components that aren t mounted to the HAWM UX UF Number Function 1 USB A jack for peripheral device connection USB B tethered jack for computer connection USB A jack for peripheral device connection USB A jack for peripheral device connection RCA jack composite video input for peripheral device connection RCA jack audio left right input for peripheral device connection To connect your projector power cable To connect your projector s network or peripheral device cables on the HAWM UX UF 48 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Connecting the power network an
41. d list identify the projector s connections to HAWM UX UF mounted components 0 100V 240V dod ES d Number Function 1 3 5 mm audio output connector recommended for SBA L speakers 2 4 pin power mini DIN 5V 2A connector reserved for ECP harness cable 7 pin mini DIN connector reserved for ECP harness cable 3 5 mm audio input connector reserved for pen tray audio cable HD DB15 VGA 2 input connector reserved for WMB RCA jack composite video input reserved for RCA pod control reserved for ECP harness cable oo NIOJ OJ AJ O RCA jack audio left right input reserved for RCA pod 9 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Using the SMART UX60 projector ECP for HAWM UX UF mounted components The following diagram and list identify the ECP ports that connect to HAWM UX UF mounted components Number Function 1 USB A jack for USB drives Power button and status LED Volume control Input selection Two mini USB B jacks connect to computers 1 and 2 11 pin connector connects to ECP harness cable OO oO BY Ww dM 4 pin connector for room control 10 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF C
42. d other peripheral device cables to your projector All cables that connect to your HAWM UX UF projector s connection panel require a certain amount of slack to accommodate the projector s rise and descent When connecting your projector s power cable don t bundle it with or place it parallel to other peripheral device cables you attach to your projector Any cables that travel the same path must be placed perpendicular at right angles to other unpowered cables to reduce signal interference 1 Connect the power cable to the projector s power socket Place the power cable through the foam padded section of the cable clip located under the projector increase the length of cable between the projector and the clip by 1 2 5 cm and then close the clip 3 Place the power cable around the back of the HAWM UX UF s interactive whiteboard brackets toward the left side of the interactive whiteboard if the power outlet is located on the left or towards the right side of the interactive whiteboard if the power outlet is located on the right 4 Connect the other end the power cable to a power outlet no more than 72 183 cm away from the projector This distance includes the amount of slack you need for the projector s range of movement If necessary use a power cable extension of an appropriate length that includes a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable 5 Slowly test the movement of t
43. date mounting the SBA L Projection Audio System directly to the interactive whiteboard That way when the speakers rise and descend with the HAWM UX UF s and interactive whiteboard s movement there s less risk of damage to the audio connection and power cables Therefore SMART recommends that you don t mount the projection audio system SBA L speakers to the wall Before connecting the audio system to the projector you must install the speaker brackets speakers and speaker cable clips according to the SBA L Projection Audio System Installation Instructions smarttech com kb 142552 1 Retrieve the 3 5 mm jack to dual channel audio output two RCA jacks cable from the SBA L packaging This is the audio connection cable Attach the 3 5 mm jack to the projector s connection panel 15 2 Place the audio connection cable toward the right side of the HAWM UX UF inserting the cable into the HAWM UX UF cable clips 3 Place the audio connection cable through the right speaker cable clip on the rear of the interactive whiteboard toward the right speaker 4 Connect the dual channel audio output to the speaker s connection panel and bundle any excess cable in the right speaker cable clip 5 Retrieve the speaker to speaker Molex double barreled cable from the SBA L packaging 6 Place the Molex cable through the left speaker cable clip through the space between the HAWM UX UF and the interactive whiteboard 7 Pl
44. e HAWM UX UF TI RCA ECP 5 Connectthe harness 11 pin connector pod cable s flat connector plug to the ECP s DB15 connector see page 9 To connect your projector s WMB 11 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Connecting the SMART UX60 projector to the wire management bundle WMB SMART recommends that when the WMB isn t in use you use the WMB s magnetic connection to attach the WMB to the HAWM UX UF s moving frame By doing so you prevent the WMB from shifting as the HAWM UX UF rises and descends CAUTION When attaching a guest computer or laptop to the projector system make sure that it is not pulled by the HAWM UX UF at its lowest or highest height NOTE If you choose to connect the WMB to the wall mounted magnetic clip do so at a height and location that doesn t interfere with the HAWM UX UF s movement 2 Place the WMB through the 1 Connect the WMB to the projector by attaching the HD DB15 connector to the projector s connection panel NOTE The USB A plug doesn t connect to the projector s connection panel cable management clip located under the projector Make sure the WMB s strain relief sits above the clip LL EE point T ee 12 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF With the ECP mounted on theleft 2 1 place the WMB around the backof pema the HAWM UX UF s interactive whiteboard brackets tow
45. ections to peripheral devices or that you use a permanent connection to the projector s connection panel 13 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Number Function 1 RCA composite video input jack for peripheral devices such as a DVD Blu ray player 2 RCA audio jack right input 3 RCA audio jack left input To connect peripheral 1 Place the device near the HAWM UX UF on a stable support and allow enough devices to your RCA excess cable length to accommodate the HAWM UX UF s rise and descent Make connector pod sure that the HAWM UX UF isn t moved while the device is attached 2 Connect your peripheral device s input cables to the jacks on the RCA connector pod 3 When you re finished with the device disconnect the cable from RCA connector pod To connect the projector to the audio jack To connect your projector to your speakers 14 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Connecting your SMART UX60 projector to the pen tray audio jack The audio and power jacks are located beside each other on the back of the pen tray 1 Connect the ends of the stereo Y cable to the VGA 1 and the VGA 2 inputs on your UF65 or UF65w projector 2 Connectthe other end of the stereo Y cable to the audio jack on the back of your interactive whiteboard s pen tray Connecting the SMART UX60 projector to the SBA L Projection Audio System The HAWM UX UF is designed to accommo
46. er brackets speakers and speaker cable clips according to the SBA L Projection Audio System textless installation instructions smarttech com kb 142552 To connect your projector to your speakers 80 CHAPTER 6 CABLING A 60013 OR 060013 SYSTEM TO HAWM UX UF Using the SMART UF55 and SMART UF55w projector connection panel for SBA and SBA L projection audio systems The following diagram and list identify the SMART UF55 and SMART UF55w projectors connections to SBA and SBA L speakers To access the cable channel remove the input output cover on the left side of the projector and remove the cable covers For more information see the SMART Board 600i3 and D600i3 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 131156 O O 100V 240V O n 50 Hz 60 Hz Number Function 1 3 5 mm audio output connector recommended for SBA SBA L speakers 1 Retrieve the 3 5 mm jack to dual channel audio output two RCA jacks cable from the SBA L packaging This is the audio connection cable The SBA packaging doesn t contain a cable of this type You must supply your own cable of a suitable length 2 Pass the audio connection cable through the boom Place the cables in the left side of the cable slot 3 Connect the audio connection cable to the projector s connection panel see above 81 CHAPTER 6 CABLING A 6001
47. esigned for use with room control systems SMART recommends that you use the video connectors for temporary connections to peripheral devices or that you permanently attach and secure the cables to the wall for installation 1 Make sure that you place the device near the HAWM UX UF on a stable support 2 Allow enough excess cable length to accommodate the HAWM UX UF s rise and descent or make sure that the HAWM UX UF isn t moved 3 Connect the device s video cables to the ECP using the appropriate inputs Input 2 is the VGA connector input 3 is the S video 4 pin mini DIN connector and input 4 is the composite video input connector 4 Foreach peripheral device connect the device s audio cables to the associated red and white RCA jacks next to the appropriate video input connector 5 When yourre finished with the device remove the cable from the ECP Connecting your SMART UF55 or SMART UF55w projector to the SBA or SBA L projection audio system The HAWM UX UF is designed to accommodate mounting the SBA or SBA L projection audio system directly to the interactive whiteboard That way when the speakers rise and descend with the HAWM UX UF s and interactive whiteboard s movement there s less risk of damage to the audio connection and power cables Therefore SMART recommends that you don t mount the SBA or SBA L projection audio system to the wall Before connecting the audio system to the projector you must install the speak
48. h of cable between the projector and the clip by 1 2 5 cm and then close the clip 20 5 10 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF When connecting cables from the ESE projector to the interactive whiteboard make SSS sure that all cables pass between the two wall mount interactive whiteboard brackets Once the cables are b through the L brackets place the RCA EP harness cable connector pod toward the left side of the interactive whiteboard for proximity to the left mounted ECP Attach the cables to the lower cable clips on the HAWM UX UF If you have many cables attached smoothly bundle your peripheral device cables together using a cable tie not included Attach a cable management clip not included to the cables or cable bundles making sure there s a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable If you don t want to connect a network cable proceed to the next step Otherwise connect the other end of the network cable to your LAN port Connect the other end of the cables to your peripheral devices Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cables aren t taut at any range of the HAWM UX UF s movement If they re still taut repeat this procedure until you find a suitable mounting location or length for the cables 21 CHAP
49. he unit using the HAWM UX UF s mobility switch Make sure that the cable isn t taut at any range of the HAWM UX UF s movement g TIP Find a support location for the power cable that doesn t interfere with the movement of the HAWM UX UF and attach a cable management clip not included to the cable Make sure that you have enough slack for the HAWM UX UF to move freely and then bundle the excess This is strongly recommended 1 If you don t want to connect a network cable proceed to step 3 Otherwise make sure you have a network cable with RJ45 plugs not included long enough to connect your projector to a LAN port 2 Connect the RJ45 plug on the network cable to the RJ45 port on the projector Make sure that the network cable is in the middle left position in the cable slot 3 Connect your peripheral device cables to the appropriate locations on the projector s connection panel 49 4 10 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Place all cables through the foam padded section of the cable clip located under the projector Increase the length of cable between the projector and the clip by 1 2 5 cm and then close the clip Place the cables around the back of the HAWM UX UF s interactive whiteboard brackets toward the left side of the interactive whiteboard if the peripheral device or LAN port is located on the left or towards the right side of the interactive whiteboard if the
50. k of the HAWM UX UF toward the left side of the interactive whiteboard for proximity to the left mounted ECP 5 Place the harness cable through the upper cable clips you installed on the side of the HAWM UX UF 6 Connect the harness cable s DB15M plug to the ECP s DB15 connector To connect peripheral devices to your RCA connector pod 27 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Connecting peripheral devices to the RCA connector pod The RCA connector pod enables you to connect DVD Blu ray players and other devices to our interactive whiteboard system using the three RCA jacks The composite video connector and associated dual channel audio inputs on the RCA connector pod are for input only Number Function 1 RCA composite video input jack for peripheral devices such as a DVD Blu ray player 2 RCA audio jack right input 3 RCA audio jack left input 1 If you have speakers installed turn the volume dial on the ECP all the way down to prevent buzzing or sparking 2 Connect your peripheral device s input cables to the jacks on the RCA connector pod To connect the projector to the audio jack To connect your projector to your speakers 28 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Connecting your SMART UF65 and SMART UF65w projector to the pen tray audio jack The audio and power jacks are located beside each other on the back of the pen
51. ket oa BRB OJN RJ45 jack for network connections NOTE SMART recommends that you use a VGA out connector on your source input to simplify the cable placement 32 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Using the SMART UF65 and SMART UF65w projector ECP for other components The following diagram and list identify the ECP connections to components that aren t mounted to the HAWM UX UF Number Function 1 USB A jack for USB drives Power button and status light Volume control Input selection Two mini USB B jacks connect to computers 1 and 2 11 pin connector connects to ECP harness cable AJ OJIN 4 pin connector for room control Connecting the power network and other peripheral device cables to your SMART UF65 or SMART UF65w projector Peripheral devices that don t mount on the HAWM UX UF but that connect to your projector s connection panel on the HAWM UX UF require a certain amount of slack in the cable for the projector s rise and descent When connecting your projector s power cable don t bundle it with or place it parallel to other peripheral device cables you attach to your projector If the wires cross or travel the same path make sure it is placed perpendicular at right angles to other unpowered cables To connect your projector power cable on the HAWM UX UF To connect your projector s network and peripheral
52. mm jack to dual channel audio output two RCA jacks cable from the SBA L packaging Attach the 3 5 mm jack to the projector s connection panel 44 CHAPTER 4 CABLING A 685ix OR Place the audio connection cable toward the right of the HAWM UX UF inserting the cable into the HAWM UX UF cable clips Place the audio connection cable through the right speaker cable clip on the rear of the interactive whiteboard toward the right speaker Connect the dual channel audio output to the speaker s connection panel and bundle any excess cable in the right speaker cable clip Retrieve the speaker to speaker Molex double barreled cable from the SBA L packaging Place the Molex cable through the left speaker cable clip through the space between the HAWM UX UF and the interactive whiteboard Place the cable through the right speaker cable clip Connect the Molex cable to both speakers and bundle any excess cable in the left speaker cable clip Lu ONES 22 7 2 E7725 D685ix SYSTEM HAWM UX UF Right speaker Left speaker cable clip 45 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Placing cables for other components Cables for peripheral devices connected to the projector but not mounted on the HAWM UX UF are at the greatest risk of damage because they shift as the HAWM UX UF rises and descends These peripheral devices and cables
53. n mini DIN connector to the projector s connection panel Attach the screw on the ECP strain relief to the projector housing using a Phillips No 2 screwdriver Using a cable tie secure the power cable to the SMART UF65 or SMART UF65w projector s wall mount bracket Place the cable through the cable cutouts on the wall mount bracket Place the harness cable around Wo A the back of the HAWM UX UF s interactive whiteboard brackets toward the left side of the interactive whiteboard if the ECP is mounted on the left or toward the right side of the interactive whiteboard if the ECP is mounted on the right Cable clips Place the harness cable through the upper cable clips you installed on the side of the HAWM UX UF Connect the harness cable s DB15M plug to the ECP s DB15 connector To connect your projector to your speakers 57 CHAPTER 5 CABLING A 60014 060014 SYSTEM TO A HAWM UX UF Connecting your SMART UF65 or SMART UF65w projector to the SBA L projection audio system The HAWM UX UF is designed to accommodate mounting the SBA L projection audio System directly to the interactive whiteboard That way when the speakers rise and descend with the HAWM UX UF s and interactive whiteboard s movement there s less risk of damage to the audio connection and power cables Therefore SMART recommends that you don t mount the SBA L Projection Audio System to the wall Before connecting the
54. omizing your cables bete rte ti te 4 Introduction Your SMART HAWM UX UF Height Adjustable Wall Mount HAWM UX UF is an easy to adjust platform for connecting the components of your SMART Board interactive whiteboard system However placing cables on your HAWM UX UF requires care and attention The HAWM UX UF enables you to operate your interactive whiteboard system at multiple levels depending on your users comfort access and personal height needs Some equipment that you connect to your HAWM UX UF isn t movable and can pose a risk of cable damage unless you take special precautions By following this guide and carefully examining the lengths of cable you need you can ensure trouble free installation and years of safe operation If you re connecting your HAWM UX UF to a SMART Mobile Height Adjustable Floor Stand FS UX see the FS UX Height Adjustable Floor Stand Installation and Integrator s Guide smarttech com kb 147510 for additional instructions 2 CHAPTER 1 BEST PRACTICES FOR CABLING YOUR HAWM UX UF Best practices for cabling Use the best practices in this section when placing cables for any type of interactive whiteboard system mounted on a HAWM UX UF Following these best practices makes it easier to install peripheral devices to your interactive whiteboard system improves the safety and security of your system and prevents damage to your devices Don t mount your HAWM UX UF in the way of power
55. on t want to connect a network cable proceed to the next step Connect the RJ45 plug on the network cable to the RJ45 port on the projector making sure that the network cable is in the middle left position in the cable slot 6 Secure the cable to the SMART UF65 or SMART UF65w projector s wall mount bracket using a cable tie Place the cables through the cable cutouts on the bottom wall mount bracket 7 Place the cables Pr ea Lower cable around the back of clips the HAWM UX UF toward the left side of the interactive whiteboard if the peripheral device or LAN port is located on the left or toward the right side of the interactive whiteboard if the peripheral device or LAN port is located on the right 8 Attach the cables to the lower cable clips on the HAWM Cable management clips 9 If you have many cables attached smoothly bundle your peripheral device cables together using a cable tie not included 10 Attach a cable management clip not included to the cables or cable bundles making sure there s a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable To connect a composite video device 63 CHAPTER 5 CABLING A 60014 060014 SYSTEM TO A HAWM UX UF 11 If you don t want to connect a network cable proceed to the next step Otherwise connect the other end of the network cable to your LAN port 12 Connect the other end of the cables to
56. onnecting the SMART UX60 projector s ECP harness cable The ECP harness cable controls all signals and commands sent between the ECP and the projector To install your ECP follow the instructions in the SMART Board X885ix Interactive Whiteboard System Installation Instructions smarttech com kb 149616 To connect your 1 Attach the SMART UX60 projector s ECP harness cable to the projector by projector s ECP harness attaching the 4 pin power mini DIN connector and the 7 pin mini DIN connector to cable the projector s connection panel and the 089 to the control port as listed on the projector connection panel see page 8 2 Place the harness cable through the cable management clip located under the projector Make sure the ASX harness cable s strain relief sits L oq8 above the clip point m c he IMPORTANT c e Li add slack to the cable move the cable to the clip s foam padded section increase the length of cable between the clip and the projector and close the clip 3 Connect cables from the projector to the interactive whiteboard she shen making sure that all cables pass between the two interactive whiteboard wall mounting brackets Once the cables are through the brackets place the harness cable toward the left side of the interactive whiteboard for proximity to the left mounted ECP 4 Place the harness cable through the upper cable clips on the side of v ES gt th
57. ount the peripheral device to a permanent location and check cabling to ensure there s enough slack and that there are no obstructions in the cable path Cable friction rubbing and strain can occur if you don t take the proper precautions When connecting these peripheral devices make sure there s enough slack mount the peripheral device to a permanent location and make sure there are no obstructions in the cable path Cable friction rubbing and strain can occur if you don t take the proper precautions Using the SMART UF65 and SMART UF65w projector connection panel for other components The following diagram and list identify the SMART UF65 and SMART UF65w projector s connections to components that don t mount on the HAWM UX UF 31 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Remove the input output cover on the left side of the projector and remove the cable covers to access the projector connection panel and wire management clip For more information see the SMART Board X800i4 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 150699 Number Function 1 RCA jack audio left right input reserved for S video input S video input connector Audio 1 and 2 reserved for audio cable from pen tray HD DB15 VGA 2 connector reserved for WMB HD DB15 VGA 1 connector VGA output Power soc
58. peat this procedure until you find a suitable mounting location or length for the cables Connecting your host computer to the projector or ECP You must connect your host computer s video and audio outputs to your SMART UF55 projector or SMART UF55w projector or ECP If you use guest computers SMART recommends that you install your host computer s video output to your projector and reserve the VGA connector on the ECP for a guest computer connection such as a laptop If you don t use guest computers SMART recommends that you install your host computer s video output to the VGA connector on the ECP This makes the cable installation of SMART UF55 and SMART UF55w projectors much simpler Use only one set of the following instructions for your specific installation 77 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF To connect your host 1 Make sure you have VGA and 3 5 mm audio cables not included long enough to computer s audio and connect your computer to your SMART UF55 or SMART UF55w projector video output to the 2 Pass the VGA and audio cables through the boom and connect your VGA cable to projector the Computer VGA 2 input on your projector 3 Connect your 3 5 mm audio cable to the Audio 2 input on your projector 4 Secure the cables to the SMART UF55 or SMART UF55w projector s wall mount bracket using a cable tie Place the cables through the cable cutou
59. peripheral device cables you attach to your projector Any cables that travel the same path must be placed perpendicular at right angles to other unpowered cables to reduce signal interference To connect your projector power cable To connect your projector s network and ECP harness cables on the HAWM UX UF 74 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF 1 Pass the power cable through the boom and then connect it to the power socket Make sure that the power cable is in the far right position in the cable slot Cable slot Secure the power cable to the SMART UF55 or SMART UF55w projector s wall mount bracket using a cable tie Place the cable through the cable cutouts on the wall mount bracket Place the power cable around the back of the HAWM UX UF s interactive whiteboard brackets toward the left side of the interactive whiteboard if the power outlet is located on the left or toward the right side of the interactive whiteboard if the power outlet is located on the right Connect the other end of the power cable to a power outlet no more than 72 183 cm away from the projector This distance includes the amount of slack you need for the projector s range of movement If necessary use a power cable extension of an appropriate length that includes a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable Slowl
60. peripheral device or LAN port is located on the right Cable management clips Lower cable clips Attach the cables to the lower cable clips on the HAWM UX UF If you have many cables attached smoothly bundle your peripheral device cables together using a cable tie not included Attach a cable management clip not included to the cables or cable bundles at a location on the wall that includes a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable If you don t want to connect a network cable proceed to the next step Otherwise connect the other end of the network cable to your LAN port Connect the other end of the cables to your peripheral devices Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cables aren t taut at any range of the HAWM UX UF s movement If they re still taut repeat this procedure until you find a suitable mounting location or length for the cables To connect a composite video device 50 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Connecting composite video and USB devices to your projector s ECP The ECP has three USB A jacks and one composite video RCA jack with associated dual channel audio RCA jacks SMART recommends that you install only small USB devices such as a USB drive or that you use a USB port on your computer for larger devices to eliminate the risk of cable d
61. r button and status light Volume control Input selection Two mini USB B jacks connect to computers 1 and 2 11 pin connector connects to ECP harness cable OO oO BY wl dM 4 pin connector for room control Connecting the power network and other peripheral device cables to your projector All cables that connect to your HAWM UX UF projector s connection panel require a certain amount of slack to accommodate the projector s rise and descent When connecting your projector s power cable don t bundle it with or place it parallel to other peripheral device cables you attach to your projector Any cables that travel the same path must be placed perpendicular at right angles to other unpowered cables to reduce signal interference To connect your projector power cable on the HAWM UX UF To connect your projector s network or peripheral device cables on the HAWM UX UF 19 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF 1 Connect the power cable to the projector s power socket Place the power cable through the foam padded section of the cable clip located under the projector increase the length of cable between the projector and the clip by 1 2 5 cm and then close the clip Place the power cable around the back of the HAWM UX UF toward the left side of the interactive whiteboard if the power outlet is located on the left or toward the right side of the interactive whitebo
62. r peripheral device cables together using a cable tie not included Attach a cable management clip not included to the cables or cable bundles making sure there s a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable If you don t want to connect a network cable proceed to the next step Otherwise connect the other end of the network cable to your LAN port Connect the other end of the cables to your peripheral devices Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cables aren t taut at any range of the HAWM UX UF s movement If they re still taut repeat this procedure until you find a suitable mounting location or length for the cables 35 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Chapter 4 Cabling a 685ix or D685ix system to a HAWM UX UF 0 oio 37 Mounting your HAWM UX UF mobility switch eene 37 Placing cables for HAWM UX UF mounted components 39 Placing cables for other 46 Introduction SMART Board 685ix and D685ix interactive whiteboard systems always include a SMART UX60 ultra short throw projector and an extended control panel ECP located on the interactive whiteboard IMPORTANT Before following these instructions install your HAWM UX UF and interactive whiteboard system according to the SMART
63. ractive Whiteboard System Installation Instructions smarttech com kb 137394 1 Attach the SMART UX60 projector s ECP harness cable to the projector by attaching the composite video RCA jack its associated dual channel audio input two RCA jacks the 4 pin power mini DIN connector and the 7 pin mini DIN connector to the projector s connection panel as listed on the projector connection panel see page 38 2 Place the harness cable through the cable management clip located WAS under the projector Make ZANI sure the harness cable s t DON strain relief sits above the EX clip point IMPORTANT To add slack to the cable move the cable to the clip s foam padded section increase the length of cable between the clip and the projector and close the clip To connect your projector s WMB 41 CHAPTER 4 CABLING A 685ix OR D685ix SYSTEM TO A HAWM UX UF Place the harness cable around the back of the HAWM UX UF s interactive whiteboard brackets toward the left side of the interactive whiteboard if the ECP is mounted on the left or toward the right side of the interactive whiteboard if the ECP is mounted on the right Place the harness cable through the upper cable clips on the side of the HAWM UX UF Connect the DB15M harness cable s plug to the ECP s DB15 connector see page 38 Upper cable clips Connecting the SMAR
64. rary connections 50 800i4 interactive whiteboard network cable connection 33 peripheral cable connection 33 SMART hub VE220 and SE240 30 SMART UF65 projector power cable 33 885ix interactive whiteboard mobility switch 6 network cable 19 peripheral device cables 19 SMART hub VE220 and SE240 16 SMART UX60 projector power cable 19 A audio system 60013 interactive whiteboard 79 600i4 interactive whiteboard 57 685ix interactive whiteboard 43 800i4 interactive whiteboard 28 885ix interactive whiteboard 14 SMART UF65 projector 28 SMART UX60 projector 14 43 B best practice assessing your installation location 4 cabling on HAWM UX UF 1 preventing tripping hazards 3 C cable damage 2 cable lengths SMART supplied 4 user supplied 4 cabling to mobile floor stand FS UX 1 84 INDEX ECP 800i4 interactive whiteboard 25 885ix interactive whiteboard 9 SMART UF55 projector 74 SMART UF55 projector remote mounted 78 SMART UF65 projector 25 32 60 SMART UX60 projector 47 G guest computer cable placement 2 H Height Adjustable Wall Mount UX UF connecting a laptop to your 2 L Laptop cable placement 2 M minimum cable length measuring 4 mobile floor stand FS UX cabling 7 mobility switch 60013 interactive whiteboard 66 600i4 interactive whiteboard 52 685ix interactive whiteboard 36 800i4 interactive whiteboard 22 885ix interactive whiteboard 6 placement 7
65. reserved for ECP harness cable 4 RCA jack composite video input connector reserved for ECP harness cable 5 3 5 mm audio output connector for VGA 2 In connector 6 HD DB15 VGA 2 connector reserved for ECP harness cable 7 3 5 mm audio output connector for VGA 1 In connector 8 HD DB15 VGA 1 connector computer analog signal component video input 9 HD DB15 VGA output connector 10 Power socket 11 RS 232 connector reserved for ECP harness 12 RJ45 jack for network connections IMPORTANT Use only the input Computer 1 on your projector to connect the ECP harness cable 73 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF NOTE SMART recommends that you use a VGA out from your source input to simplify the cable placement Connecting your SMART UF55 and SMART UF55w projector s ECP harness cable The following diagram and list identify the ECP s DB25 and VGA connections to the ECP harness cable Number Function 1 HD DB15 VGA 2 connector reserved for ECP harness cable 2 DB25 connector reserved for ECP harness cable Connecting the power network ECP and peripheral device cables to your SMART UF55 or SMART UF55w projector All cables that connect to your HAWM UX UF projector s connection panel require a certain amount of slack to accommodate the projector s rise and descent When connecting your projector s power cable don t bundle it with or place it parallel to other
66. row projector and an extended control panel ECP located on the interactive whiteboard IMPORTANT Before following these instructions install your HAWM UX UF and interactive whiteboard system according to the SMART HAWM UX UF installation guide smarttech com kb 145745 The instructions below are a supplement to and not a substitute for the installation guide 6 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF Mounting your HAWM UX UF mobility switch The mobility switch controls the vertical movement of the HAWM UX UF and your interactive whiteboard system The mobility switch is wired directly to the rear panel of the HAWM UX UF Use the installation guide with the following procedure to place and mount the mobility switch To mount the 1 Locate the HAWM UX UF mobility switch and then remove and discard the mobility switch plastic bag that holds the mobility switch 2 Choose the mobility switch s mounting location There are mounting holes on the left and the right sides and near the top and the bottom of the interactive whiteboard IMPORTANT If you installed or plan to install the SMART Audio projection audio system SBA L mount the mobility switch on the bottom mounting holes 7 CHAPTER 2 CABLING AN 885ix SYSTEM TO A HAWM UX UF 3 Secure the mobility switch cable using a Phillips amp No 2 screwdriver and the two 4 Place the cable through the 5
67. s and or joint venture partners Blu ray is a trademark of the Blu ray Disc Association HDMI is a trademark or registered trademark of HDMI Licensing LLC Phillips is a registered trademark of Phillips Screw Company All other third party product and company names may be trademarks of their respective owners Copyright Notice 2011 SMART Technologies ULC All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART 02 2011 Contents Product Registration B Contents i 1 Best practices for cabling your HAWM UX UF 1 1 Best practices for cabling eene nnne nnns 2 Customizing your cables rd ttp t 4 Cabling an 885ix system to a 5 em 5 Mounting your HAWM UX UF mobility switch 6 Placing cables for HAWM UX UF mounted components 7 Placing cables for other 16 Cabling 880i4 or 88514 system to a HAWM UXJ UF 21
68. s into the wall at the four drill hole locations Attach but don t tighten two screws in the two top plastic anchors using a Phillips No 2 screwdriver Leave a 1 8 3 mm gap between the screw and the anchor 22 lt Attach the ECP to the screws using the top two key holes on the ECP 71 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF 10 Flip up the bottom panel of the ECP Attach two screws in the two bottom plastic anchors using a Phillips No 2 screwdriver Using the SMART UF55 and SMART UF55w projector s connection panel for remotely mounted components To access the projector connection panel and wire management clip first remove the input output cover on the left side of the projector and remove the cable covers For more information see the SMART Board 600i3 and D600i3 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 131156 The following diagram and list identify the SMART UF55 and SMART UF55w projectors connections to components that don t mount to the HAWM UX UF 72 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF eo Number Function 1 RCA jack audio left right input reserved for ECP harness cable 2 S video input connector reserved for ECP harness cable 3 RCA jack audio left right input
69. sary use a power cable extension of an appropriate length that includes a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable 5 Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cable isn t taut at any range of the HAWM UX UF s movement g Find a support location for the power cable that doesn t interfere with the movement of the HAWM UX UF and attach a cable management clip not included to the cable Make sure that you have enough slack for the HAWM UX UF to move freely and then bundle the excess This is strongly recommended 62 CHAPTER 5 CABLING A 60014 OR 060014 SYSTEM TO HAWM UX UF To connect your 1 If you don t want to connect a network cable proceed to step 3 Otherwise make projector s network and sure you have a network cable with RJ45 plugs not included long enough to peripheral device cables connect your projector to a LAN port he HAWM UX UF omine HMM 2 Pass the network cable through the boom and connect the RJ45 plug on the network cable to the RJ45 port on the projector Make sure that the network cable is in the middle left position in the cable slot 3 Pass peripheral device cables through the boom Make sure that the peripheral device cables are in the middle left position in the cable slot 4 Connect your peripheral device cables to the appropriate locations on the projector s connection panel 5 If you d
70. t shift after they re installed To prevent cable friction SMART recommends that you place these cables first Using the SMART UF65 and SMART UF65W projector connection panel for HAWM UX UF mounted components The following diagram and list identify the SMART UF65 and SMART UF65w projector connections to HAWM UX UF mounted components To access the projector connection panel and wire management clip remove the input output cover on the left side of the projector and remove the cable covers For more information see the SMART Board X800i4 Interactive Whiteboard System Configuration and User s Guide smarttech com kb 150699 E Number Function 1 4 pin power mini DIN 5V 2A connector reserved for ECP harness cable 7 pin mini DIN connector reserved for ECP harness cable RCA jack composite video input reserved for RCA pod RCA jack audio left right input reserved for RCA pod Audio 1 and Audio 2 reserved for audio cable from pen tray 3 5 mm audio output connector recommended for SBA L speakers oO AJ OJIN DB9 control reserved for ECP harness 25 CHAPTER 3 CABLING AN 880i4 OR 885i4 SYSTEM TO A HAWM UX UF Using the SMART UF65 and SMART UF65w projector ECP for HAWM UX UF mounted components The following diagram and list identify the ECP ports that connect to HAWM UX UF mounted components Number
71. ts on the bottom wall mount bracket 5 Place the cables around the back of the HAWM UX UF toward the left side of the interactive whiteboard if your computer is located on the left or toward the right side of the interactive whiteboard if your computer is located on the right 6 If you have many cables attached smoothly bundle your peripheral device cables together using a cable tie not included 7 Connect the other ends of your VGA and audio cables to your computer s video output connector 8 Attach a cable management clip not included to the cables or cable bundles making sure that there s a minimum of 28 71 1 cm excess straight length or a 14 35 6 cm loose loop of cable 9 Slowly test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cables aren t taut at any range of the HAWM UX UF s movement If the cables are still taut repeat this procedure until you find a suitable mounting location or length for the cables To connect your host computer s audio and video output to the ECP 78 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF 1 Make sure you have a VGA and 3 5 mm audio cables not included long enough to connect your computer to your ECP Connect the VGA and 3 5 mm audio cables to the VGA and 3 5 mm input connector on the bottom of your ECP 3 Connect the other end of your the VGA and audio cables to the VGA
72. twork and other peripheral device cables to your SMART UF65 or SMART UF65w projector Peripheral devices that don t mount on the HAWM UX UF but that connect to your projector s connection panel on the HAWM UX UF require a certain amount of slack in the cable for the projector s rise and descent When connecting your projector s power cable don t bundle it with or place it parallel to other peripheral device cables you attach to your projector If the wires cross or travel the same path make sure it is placed perpendicular at right angles to other unpowered cables 1 Pass the power cable through the boom and then connect it to the power socket Make sure that the power cable is in the far right position in the cable slot Cable slot 2 Secure the power cable to the SMART UF65 or SMART UF65w projector s wall mount bracket using a cable tie Place the cable through the cable cutouts on the wall mount bracket 3 Place the power cable around the back of the HAWM UX UF toward the left side of the interactive whiteboard if the power outlet is located on the left or toward the right side of the interactive whiteboard if the power outlet is located on the right 4 Connect the other end of the power cable to a power outlet no more than 72 183 cm away from the projector This distance includes the amount of slack you need for the projector s range of movement If neces
73. y test the movement of the unit using the HAWM UX UF s mobility switch Make sure the cable isn t taut at any range of the HAWM UX UF s movement Find support location for the power cable that doesn t interfere with the movement of the HAWM UX UF and attach a cable management clip not included to the cable Make sure that you have enough slack for the HAWM UX UF to move freely and then bundle the excess This is highly recommended If you don t want to connect a network cable proceed to the next step Otherwise make sure you have a network cable with RJ45 plugs not included long enough to connect your projector to a LAN port 75 2 CHAPTER 6 CABLING A 60013 OR D60013 SYSTEM TO A HAWM UX UF Pass the ECP cable through the cable slot The upper part of the ECP cable is too thick to fit inside the cable slot so put the thinner part of the ECP cable in the cable slot Connect the S Video connector and two audio left right RCA jacks the DB9 control cable and the composite video and two audio left right RCA jacks from the ECP harness cable to their receptacles on the projector s connection panel Attach the screw on the ECP strain relief to the projector housing using a Phillips No 2 screwdriver If you don t want to connect a network cable proceed to the next step Otherwise pass the network cable through the boom and connect the RJ45
Download Pdf Manuals
Related Search