SkyLink SK8 User's Manual
Contents
1. A NOTE Usea sharp non conductive object like a pen or pencil to press the learn button Section 10 The Wiring Diagram 2 1 Press the Switch Button on the Wall Switch receiver to turn the lights on The two blue LEDs should go off 3 2 Transmit an Erase code from the transmitter until step 5 Refer to the user s instructions of the transmitter on how to transmit an Erase code 4 3 Press and hold the learn button for about 3 seconds until the upper blue LED flashes Switch Button Blue LEDs Learn Button 4 Release the learn button 5 All devices have now been successfully erased Turn the light on with the programmed transmitter or Switch Button Press and hold the learn button on the Wall Switch receiver for about 3 seconds until the upper blue LED flashes quickly Release the learn button The Wall Switch receiver is now in the On Off Mode Troubleshooting A NOTE Wire colours may vary in the junction box T 2 Problem Solution Wiring Diagram without Neutral Wire finn Load Red I Load Usually Black Red or Blue Wall Switch Receiver s LEDs and the connected load will not turn on My switch has more than 3 wires in the wall box Ensure the wires are side by side and held together when pushing them inside the wire nuts Ensure the corresponding wires are connected correctly Refer to Section 10 Chec2. Switch transmitter is now ready to be controlled Drill 2 pilot holes amp insert anchors Turn the circuit breaker back on The two blue LEDs will be on If the blue LEDs remain off please check and ensure the light bulb is installed and in good position and that the wires are connected correctly After the Wall Switch is installed press the Switch Button to turn the lights on and off Switch Button Section 3 Operation Wall Switch Receiver 1 To turn the light on press the Switch Button once and to turn it off press it once more Press Section 2 Setting up the Wireless Wall Switch Transmitter INSTALLING WITH DOUBLE SIDED TAPE NOTE The Wireless Wall Switch Transmitter comes with a lithium battery already installed Remove the battery isolator tag from the Wireless Wall Switch transmitter before installing 1 First clean the wall surface where you plan to install the Wireless Wall Switch transmitter 2 Place the two foam tapes E on the back of the Wireless Wall Switch transmitter plate Peel off the foam tape cover and stick it to the wall surface Place double sided foam tape Wireless Wall Switch Transmitter 1 To turn the light on and off push the Wireless Wall Switch pad from one position to the other Push Push Section 4 Programming Section 5 Erasing NOTE Before programming remove the wall plate on the Wireless Wall Switch transmitter by lo
3. Wall Switch with the 3 wires Live Load and Ground Use the provided wire nuts C to connect these wires respectively to the existing wires from the wall Neutral wire is not required and cannot be connected to the Wall Switch Receiver Refer to Section 10 for neutral wiring After all the wires are connected ensure that all of the wire connectors are attached securely and there should be no exposed copper wiring Secure the Wall Switch with screws Ground Usually copper or green Grey Antenna i n A NOTE Do not cut the antenna Section 2 Setting up continued INSTALLING WITH SCREWS NOTE The Wall Mount transmitter comes with a lithium battery already installed Remove the battery isolator tag from the Wall Mount Transmitter before installing Installing to an Existing Wall Switch 1 Loosen the screws on the wall plate of the Wireless Wall Switch transmitter and tighten the two included screws D on the back plate to the existing wall box 2 Tighten the two screws on the wall plate to the back plate to secure it 3 The Wireless Wall Switch transmitter is now ready to be controlled Existing Wall Box No Anchor Installing on New Wall Surface 1 Drill two small pilot holes based on the two mounting screw positions and insert the anchors D before tightening the back plate with screws D 2 Tighten the two screws on the wall plate to the back plate to secure it 3 The Wireless Wall
4. Z N SKY oat INSTALLATION INSTRUCTIONS WIRELESS 3 WAY ON OFF KIT Model SK8 SkylinkHome Congratulations on your purchase of the SkylinkHome Wireless 3 Way On Off Kit model SK8 Simply replace your existing wall switch with the Skylink Wall Switch receiver and mount the Wireless Wall Switch Transmitter anywhere you would like to control your lighting Warranty ONE YEAR WARRANTY This product is guaranteed to be free of defects in materials and workmanship for 1 year from the date of purchase If this product is defective call 1 800 304 1187 for repair or replacement parts Guarantee does not include normal wear and tear or batteries Z N SKY Cy If you have any questions problems or missing parts please call Skylink Customer Support 9 00am 5 00pm EST Monday Friday 1 800 304 1187 Or e mail us at support skylinkhome com www skylinkhome com CUSTOMER SERVICE 17 Sheard Avenue Brampton Ontario Canada L6Y1J3 P N 101Y157 Rev 0 2014 SKYLINK GROUP Safety Information O Turn off power to the circuit breaker before installing O If you are uncertain or uncomfortable performing this installation please consult a qualified electrician This manual should also be kept for future reference O For indoor use only O DO NOT use this product to control loads over the specified maximum rating The device is approved by the FCC and it complies with Part 15 of the FCC Rules Its operation is sub
5. er Mode The timer duration can be set for the following times 1 minute 5 minutes 15 minutes 30 minutes or 60 minutes like to go back to other settings such as 1 minute release the button and repeat A NOTE Once the number of flashes reaches 5 it will stay at this setting If you would from step 1 to start over A NOTE Use a sharp non conductive object like a pen or pencil to press the learn button 1 The connected light must be turned off and the two blue LEDs should be on 2 Press and hold the learn button for three seconds until the lower blue LED flashes once The number of flashes indicates the timer duration 3 Continue to hold the learn button until it reaches the desired setting The status will change every 6 seconds so holding the learn button for another 6 seconds the number of flashes will change from 1 to 2 2 to 3 etc Once a transmitter is programmed for the timer mode activating this programmed transmitter will turn the lights on for the specified timer duration To stop timer countdown press a programmed button for regular mode for timer operation the timer will start again and override the previous timer This will extend the on period by another timer interval Accessories Add up to eight Skylink Wireless Transmitters A NOTE During a timer countdown if the Wall Switch receiver receives another signal Wireless Wall Switch Model TB 318 Motion Sensor Mode
6. ject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference that may cause undesired operation WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user s atuhority to operate the equipment Technical Specifications Input Voltage 120V AC 60Hz Standby Current 0 2mA Minimum Load 10W Maximum Ballast Load 500W Maximum Tungsten Load 600W Maximum Resistive Load 1000W Operating Frequency 318MHz Operational Temperature 4 F 140 F 20 C 60 C Humidity 5 95 Range Up to 500 feet in open area Package Contents Wall Switch Receiver a Wireless Wall Switch Transmitter E Double sided Foam Tape Section 1 Setting up the Wall Switch Receiver the circuit breaker Failure to turn off power at the circuit breaker can result in electrical WARNING Turn off power to the circuit that you plan on installing the Wall Switch to at shock causing severe or fatal injury A NOTE The Wall Switch is designed to operate a maximum load of 1000W at 120VAC NOTE Ifyou already have an existing 3 Way Switch disable one switch and replace the other switch with the Wall Switch Receiver Loosen the screws on the wallplate cover of the Wall Switch receiver and remove it before installing Install the
7. k that the circuit breaker is turned on If there are white wires neutral in the wall box connect the white wire with a wire nut Only connect the Load and Live wires from the wall box to the Wall Switch Receiver Ground Usually Copper or Green Wire Ground Green The Wall Switch Receiver This is normal Ensure the connected Antenna Grey is getting warm to touch load does not exceed the maximum rating TRE T ver sa The range of my Wall Keep the antenna wire as straight as dd ped aon eee Switch Receiver is possible and put it directly into the dry Neutral White wall or via the hole in the wall box decreasing It takes a long time for the light to turn off when set to Timer Mode Ensure the timer duration is set to the desired setting Check that there were no other Timer Mode signals being received as that will extend the ON period by another interval Usually Black Red or Blue ti Ground Green Ground Usually Copper or Green Wire Can dim the light on my Wall Switch Receiver Not with this kit Purchase the Skylink Wall Dimmer WR 001 or WR 318 instead of this Wall Switch Receiver Antenna Grey Section 7 Countdown Timer Mode NOTE If the Countdown Timer Mode is activated the light connected to the Wall Switch receiver will flash for a predetermined time interval and then turn off NOTE You must compete the programming
8. l ID 318 SkylinkHome t Snap On Remote Keychain Remote LCD Deluxe Remote Model TM 318 Model LK 318 Model TD 318 0 000 e 4 a 000 000 i 2 000 B O 6 va now mer O2 O8 o N f f Wireless Remote Control TC Series TC Series Remotes are available in 1 to 14 buttons For more information visit www skylinkhome com
9. osening the screws A NOTE Use a sharp non conductive object like a pen or pencil to press the learn button 1 Press the Switch Button on the Wall Switch receiver to turn the lights on The two blue LEDs should go off 2 Press and hold the learn button for about three seconds until the upper blue LED flashes quickly and then release the learn button Touch Plate Learn Button 3 Press the learn button on your Wireless Wall Switch transmitter The red LED will be on for 15 seconds 4 Press the pad switch on the Wall Switch Transmitter the red LED will flash and then go off The upper blue LED on the Wall Switch Receiver will also turn off 5 Both wall switches are now programmed Learn Button Red LED Pad Section 9 Replacing the Battery 1 Remove the wall plate from the Wireless Wall Switch transmitter by loosening the two screws 2 Remove the existing battery by sliding it out 3 Insert the new battery positive side up by sliding it in and pushing down on the battery to lock it in place 4 When the battery is installed the red LED on the transmitter will be on for one second Slide in Battery Positive side up Red LED Section 6 Enable Disable On Off Section6 Enable DisableOn orh NOTE All previously programmed devices will be erased You must re program the devices you want to keep A NOTE On Off Mode turns the lights on off
10. sequence within the 15 second interval otherwise the Wall Switch receiver will quit from programming mode and you will need to start again from step 1 A NOTE Use a sharp non conductive object like a pen or pencil to press the learn button 1 To program a transmitter to operate in Countdown Timer Mode hold the learn button on your Wall Switch receiver for about 10 seconds until the upper blue LED is on steadily then release the learn button 2 Press the learn button on your transmitter The red LED will be on for 15 seconds 3 Once the transmitter is programmed both blue LEDs will flash quickly and stop flashing 4 The transmitter has been successfully programmed Learn Button NOTE Once you have successfully completed the programming go to section 8 to setup the timer duration for the transmitter Optional Snap On Decorative Cover Snap a cover into your Skylink Wall Switch Place the Snap On Cover on the opening of the Wall Switch receiver for a more stylish look Press the button on the Snap On Cover TM 002 to turn lights on off Or carry the Snap On Remote TM 318 with you for local control and when you are done snap it back onto the Wall Switch Snap On Cover w Snap On Remote Model TM 002 Model TM 318 SkylinkHome For more information visit www skylinkhome com Section 8 Setting a Timer Duration NOTE This section is for transmitters that are programmed to Countdown Tim
Download Pdf Manuals
Related Search