Sirius Range Hoods SIU 405 User's Manual
Contents
1. are fully conversant with the require ments and limitations These units weigh approximately 125lbs and therefore require a minimum of two people to install MINIMUM AND MAXIMUMS Min length of power unit structure with deflector connected 36 6 Min length of power unit without deflector 32 Max length of power unit structure 48 Recommended height from cook top to underside of hood 30 for gas 25 for electric DUCTING If vented externally 150mm round ducting must be available for the hood through the ceiling in line with the central vertical axis of the range hood This unit must have it s own ductwork Do not under any circumstances vent this unit into any other ductwork or exhaust ducting in the building PLEASE NOTE THAT THE DUCT OUTLET ON THE TOP OF THE POWER UNIT IS OFF SET FROM CENTRE AND THEREFORE AN ADJUSTABLE 6 ROUND BEND WILL BE REQUIRED TO LINE THE EXHAUST OUTLET WITH THE 6 HOLE IN THE CEILING MOUNT BRACKET Use the shortest most direct ductwork route possible Only use metal ducting plastic ducting is generally not permitted by code Do not use flexible metal ducting as the ridges of the ducting cause severe air turbulence and will significantly reduce the efficiency of any hood THIS TYPE OF DUCTING WILL REDUCE EFFICIENCY BY 50 Vent hoods may interrupt the proper flow of exhaust gases from fire places gas furnaces and gas water heaters To minimize the risk2. button F Do not rely solely on this indicator Generally the grease filter should be washed on a regular basis to avoid grease filter fires The blower should be turned on for approximately 5 minutes before cooking in order to establish air currents upward through the hood Use the low speeds for normal use and the higher speeds for strong odors and fumes MAINTENANCE On the surfaces that are exposed directly to heat from the cook top it is advisable to clean these on a regular basis to avoid the marks from becoming baked on The hood fan should provide many years of trouble free service provided it is maintained properly Cleaning the Filter Clean the grease filter either by carefully hand washing so as not to damage the filter design or preferably in a dishwasher Depending on use the filters should be cleaned at least every two weeks in a dishwasher If a carbon filter has been fitted this must be replaced at least every 6 months as a minimum Depending on cooking style and nature of cooking greasy foods fry s curries etc would probably require more frequent replacement if odors start to manifest themselves when cooking it is time to replace the carbon filter We suggest you retain a spare set These can be ordered from the supplier of your range hood Cleaning the Hood Cleaning of the internal parts should be done with a clean damp not excessively wet cloth together with regular house
3. of drawing these lethal gases back into the home please follow the heating equipment manufacturers safety standards and guidelines Refer to NFPA and ASHRAE for additional information Duct Run Calculation The maximum duct run before effecting the performance of the hood is 100 Calculate your duct run by measuring linear feet and adding the elbows transitions and caps based on the table below Maximum Run 6 or 3 1 4 x 10 duct Deduct Each 90 elbow used Each 45 elbow used Each 6 or 3 1 4 x 10 duct Transition used Each 3 1 4 x 10 to 6 Transition used Side Wall with damper Roof Cap ELECTRICAL WARNING All electrical work must be performed by a qualified electrician Please ensure that the appropriate electrical codes or prevailing local building codes and ordinances are adhered to Ensure that the electricity supply is disconnected at source Do not use an extension cord or adapter plug with this appliance This appliance must be grounded Connect to a properly grounded branch circuit protected by a 15 amp circuit breaker Electrical Supply This appliance requires 120V 60Hz 3amp electrical supply ensure an appropriately qualified person completes the electrical hook up The connection point for the electrical supply is at the top of the unit therefore the electrical supply must be run down from the ceiling alongside the ductwork All electrical and venting hoo
4. proximity of the range hood must be avoided When frying please pay particular attention to fire risk due to grease Being highly inflammable fried oil is especially dangerous In order to avoid possible fire risk all instructions for grease filter cleaning and for removing eventual grease deposits must be followed strictly If the rating label in the cooker hood shows the If the rating label in the cooker hood does not symbol s the appliance is built in class II and show the symbol the appliance is built in it does not need any ground connection class and it needs the ground connection Only use this appliance as an exhaust ventilation system for the removal of cooking vapors DO NOT use to expel flammable substances or any other materials or vapors The installation procedures in this manual are intended for qualified installers service techni cians or persons with similar qualified background DO NOT attempt to install this appliance yourself When performing the electrical connections on the appliance please ensure that the current supply is provide with ground connection and that the voltage values correspond to those indicated on the label placed inside the appliance itself Ensure that electrical power is turned off at source before commencing installation All electri cal wiring must be properly installed insulated and grounded and conform to all applicable codes and standards Make sure all existing ductwo
5. SS INSTALLATION INSTRUCTIONS CARE AND USE MANUAL FOR SIU 404 amp SIU 405 ISLAND RANGE HOODS BEFORE INSTALLATION ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED DURING SHIPPING SHIPPING DAMAGE MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT Sirius Range Hoods Telephone Toll Free 866 528 4987 Fax Toll Free 866 365 9204 www siriushoods com info siriushoods com EC WARNINGS Thank you for purchasing a Sirius Range Hood Please read all the instructions in this manual before installing the appliance Save these instructions for future reference The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure they do not play with the appliance If the range hood is vented the air so vented must be ducted into a dedicated duct that is not showed with any other equipment whatsoever All ducting must conform to all requirements of the local authority If the range hood is to be used inside he same structure home or building as any equipment hat burns combustible material such as oil coal gas etc then pervision must be made for make up air Under certain circumstances the range hood could create a negative air pressure inside the structure This negative air pressure must not exceed 0 04 mbar please consult your local HVAC professional for guidance at this point The use of combustible material in close
6. al functioning of the hood before it is installed Before switching on the light or lights ensure the tape holding the globes in place has been removed The globes gets extremely hot and will very quickly burn the tape and discolor the globes irreparably Do not switch on the lights with the hood flat on any surface as the in tense heat will burn the surface and destroy the lamps Connect a power supply to the unit and test all func tions Installation of the island hood consists of fixing the ceiling Bracket A substantial members in the ceiling The bracket must be fixed to the frame by screwing through the ceiling into the heavy members inside the ceiling This is critically important as the entire hood fan hangs from this position and ceiling board alone will not support the weight of the hood fan Discard the plastic wall plugs supplied for fixing the bracket to the ceiling these are not appropriate for North American structures Fixing the Main Brackets Support If the range hood will be fixed to drywall we strongly recommend that you discard the wall plugs and screws supplied These anchors are only suitable for brick masonry applications We suggest the use of a more appropriate anchor system specifically designed for drywall Using Bracket A as a template mark the ceiling where the fixing screws A will be positioned remember the correct orientation from above Attach bracket A to the ceiling
7. chase Sirius reserves the right to request proof of original purchase Sirius will at its sole option and discretion replace products that arrive damaged through shipping provided shipping damage is reported as stated above within 5 business days of receipt of the shipped product or products ONE YEAR SERVICE REPAIR WARRANTY During the first year from date of original purchase Sirius will at its option repair or replace without charge any product or part which is found to be defective under normal use and service THREE YEAR PARTS WARRANTY For three years from date of purchase Sirius will provide free of charge non consumable replacement parts which are found to be defective under normal use and service WHO IS COVERED Sirius Range Hoods warrants to the original consumer purchaser of its products that such products will be free from defects in materials and workmanship for a period of three years from the original date of purchase There are no other warranties express or implied including but not limited to implied warranties of merchantability or fitness for a particular purpose or application WHAT IS NOT COVERED This warranty does not extend to filters lamps batteries ducts and ductwork components This warranty does not cover normal maintenance and service or products or parts which have been subject to misuse negligence accident improper maintenance or repair faulty installation or installation contrary to re
8. commended installation instructions The warranty on glass screens is limited to manufacturing defects only and expressly excludes cracks and breakages as a result of faulty installation Labor and associated costs associated directly with removal and re installation are expressly excluded The duration of any implied warranty is limited to the three year period as specified for the express warranty Some states and provinces do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you Canada Sirius Range Hoods Ltd USA Sirius Range Hoods Ltd 1252 Speers Road Unit 11 1051 Clinton Street Oakville ON L6L 5N9 Buffalo NY 14206 Register Online www siriushoods com warranty htm Sirius Range Hoods USA CANADA SIRIUS RANGE HOODS USA LTD SIRIUS RANGE HOODS LTD 1051 Clinton Street 1252 Speers Road Unit 11 Buffalo NY 14206 Oakville ON L6L 5N9 Telephone Toll Free 866 528 4987 Telephone 905 257 0046 Fax Toll Free 866 365 9204 Fax 905 847 0330 www siriushoods com Email info siriushoods com
9. hold detergent The external stainless steel elements should be cleaned with a good quality foaming stainless steel cleaner Read the manufacturers directions Generally they recomend that the foam be sprayed onto a clean dry cloth and then applied to the stainless steel Allow the foam to react on the surface for a few minutes and then wipe with a clean dry cloth Do not under any circumstances use an abrasive type cleaner as this will scratch and damage the stainless steel finish Glass components should be cleaned with a product such as Windex Light Bulb Replacement Turn blower and lights off Make sure the lights are cool If new lights do not operate check fuses and be sure globes and breakers are inserted correctly Do not remove the entire fixture socket as this is very difficult to reinstall Gently pry the bulb from the fixture using a soft instrument such as a toothpick Steel instruments will scratch the surface refer to figure 2 Replace the appropriate bulb Check parts brochure or specification Figure 2 sheets on our website Wipe both sides of the glass whilst it is out Re insert the glass blocking ring and fasten it Three Year Limited Warranty WARRANTY SERVICE To qualify for warranty service you must notify Sirius Range Hoods at the address stated below or call toll free USA or Canada 1 866 528 4987 and provide the model number description of the fault or defect and original date of pur
10. k ups must be in place before commencing installation of the hood fan INSTALLATION Structural Preparation for the Hood Fan Installation The island hood weighs approxi mately 125 Ibs It is therefore im perative that a substantial structure is prepared in the ceiling to attach the range hood to Ideally block off an area of at least 12 x12 between the ceiling joists using 2x4 s Allow for a hole through the center of this blocking of at least 6 in diameter through which to pass the ductwork and electrical cable The underside of the hood must not be closer than 30 from the cook to mE and ideally not higher than 32 above the cook top It is strongly recommended at this point that calculations and measurements be made and all planning and heights be finalized You will need to fit the appropriate length of ducting to the hood fan before installing it to the ceiling Planning should consist of a test assembly of the power unit and tele scoping structure before attempting to mount everything to the ceiling By following this test assembly you will be able to finalize the correct length of the assembly before mounting it to the ceiling Test assembly should include actually attaching the following items together refer schematic of components and Fixing the main support brackets below Brack ets A B C power unit and deflector if re circulating This is also a good time to test the electric
11. permanently If re circulating attach the deflector to Bracket A before fixing it to the ceiling refer schematic on page 5 The 2 brackets for the support of the chimney Part A is to be installed to Bracket A with the screws C Figure 1 Fix the structure on the ceiling by inserting the 2 dowels Figure 1 Fix Bracket C to the power unit with the nuts and washers supplied Items A on the schematic on page 9 Please ensure that the bracket is installed as shown to enable full ac cess to the square plastic black box and the metal electrical junction box Slide Bracket B over Bracket C once again ensure full access to the plastic and electrical boxes is main tained and fix it in place at the previously calculated length using the machine screws denoted by items B on the schematic on page 5 Check that the plastic flaps at the exhaust outlet for the fan move freely and have not become jammed during shipping or whilst working with the power unit Connect an appropriate length of ducting to the unit Do not fix the ducting to the outlet with screws use DUCT TAPE otand the assembled structure on a clean soft surface Ensure the underside of the hood does not get scratched and slide the chimneys of the assembled structure from the top down as per the schematic on page 5 Ensure that the holes for fixing the decorative chimney are correctly orientated with the holes at the top of bracke
12. racket A x Cable lock moyvbe rcedquired by locali ow Re Circulating Requirements Fit the carbon filter after the installation is complete these fit in behind the aluminum grease filter A short length of ductwork must be connected from the exhaust outlet up to the deflector must be purchased with hood The deflector after attaching part B with screws E connects to the top of Bracket A and forces the air out through the grills on the side of the chimney section back into the room see diagram C SCHEMATIC OF MODULAR ISLAND COMPONENTS Diagram C Deflector Assembly ei Deflector attaches to ceiling mount bracket when island hood is installed in the re circulating mode and the air that has passed through the fat and carbon filters is returned to the room via a short length of 6 round duct work attached to the power unit and deflector Diagram B Securing Bracket A to B Please note this is criticaffy i ortant do not refy on the fi cps Bracket A Diagram A Main Assembly OPERATING PROCEDURES Never pick up a flaming pan you Read all the instructions before operating the appliance Save these instructions for future reference General Advice Ensure that the grease filters are in place Without these components operating blowers could catch on to hair fingers and loose clothing Keep fan filters and surfaces clean of g
13. rease and fat Always turn hood fan ON when cooking NEVER leave cooking unattended NEVER dispose cigarette ashes ignitable substances or any foreign objects into blowers Cooking that generates flame is not recommended as this hood is equipped with a thermal overload that will shut down the motor if it senses excessive heat When frying oil in the pan can easily overheat and ignite Heat oil slowly in an appropriately sized pot covering the entire burner to reduce the risk of boiling over and burning In the event of a range top grease fire observe the following Switch OFF the range hood Turn off the cook top then smother flames with a close fitting lid cookie sheet or other metal tray If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT may be burned DO NOT USE WATER including wet dishcloths or towels as a violent steam explosion may occur Functions Island Range Hood Wireless Transmitter A Light ON OFF button B Blower Speed 1 low or OFF C Blower Speed 2 medium D Blower Speed 3 high E Blower Speed 4 intensive F 10 Minute Timer E cy p ER 4 2j S CA Filter requires washing indicator after 30 hours of use all the buttons will light up to remind you that the grease filter should be cleaned Follow the instructions for cleaning filters in this booklet Once the grease filters have been cleaned and replaced reset by pressing the timer
14. rk is clean of grease build up or ductwork should be replaced if necessary to avoid the possibility of a grease fire Check all joints on ductwork to ensure proper connection and all joints should be properly taped Be careful when cutting through ceilings or walls not to damage any hidden pipes or electrical wiring Ensure your kitchen has sufficient air return vents to replace the exhausted air TABLE OF CONTENTS BEFORE YOU BEGIN MINIMUM AND MAXIMUMS DUCTING Duct Run Calculation ELECTRICAL Electrical Supply INSTALLATION Structural preparation for the hood fan installation Fixing the Main Support Bracket Attaching the range hood to the ceiling Connecting Electricity and Ducting Re Circulating Requirements Schematic of Classical Island Components OPERATING PROCEDURES General Advice Functions MAINTENANCE Cleaning the Filter Cleaning the Hood Light Bulb Replacement WARRANTY BEFORE YOU BEGIN The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation maintenance and suitable operation of the product The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance and or installation BEFORE YOU BEGIN It is advisable to test run the range hood before installation BEFORE STARTING please read this entire document and ensure you
15. t A Attaching the Range Hood to the Ceiling The entire structure that has been pre assembled above must now be hoisted up to the ceiling A few things have to happen at once here the slots as discussed below need to be engaged and the ductwork must make connection with the length of ductwork on the structure This will require two strong people do not attempt this step on your own Bracket B has slots position C per Diagram A refer to page 5 at the top that will receive the spring clips located on Bracket A THIS IS A TEMPORARY HOLD ONLY DO NOT RELY SOLELY ON THESE CLIPS TO HOLD THE HOOD UP THEY WON T Once hooked by the spring clips immedi ately secure the structure with the machine screws at point E on the schematic on page 5 THIS MUST BE DONE IMMEDIATELY AND SHOULD NOT BE SKIPPED Ensure the entire structure is sturdy serious injury death and MAJOR damage could result should the unit not be well connected to the frame structure within the ceiling This is of utmost importance do not go any further until this has been tested and double checked the installer has sole responsibility for the safe installation of this product Connecting Electricity and Ducting Make sure power is turned off at the source Make the electrical connection see figure 2 Test the functioning of the hood Slide the upper chimney into place and attach with the machine screws provided to B
Download Pdf Manuals
Related Search