SECO-LARM USA EV-2125-N2WQ User's Manual
Contents
1. ENFORCER EV 2125 N2WQ NTSC EV 2125 P2WQ PAL Mini Vandal Dome Camera Manual ENFORCER e 1 3 Sony Super HAD II CCD e Small 3 76mm diameter e 2 9mm lens e Weatherproof IP65 e 420 TV lines e Vandal resistant design A M SCZ SECO LARM Note Model numbers that end with Q or that have a round green Q sticker signify ROHS compliant products ENFORCER Mini Vandal Dome Camera Specifications po E2125 N2WQ EV 2125 P2WQ 1 3 Sony Super HAD II 420 TV lines Internal Gain control At o 60mA Operating temperature 4 122 F 20 50 C Dimensions 3 x23 s 76x60 mm Weight 6 4 0z 182g Parts List 1 x Manual 3 x Mounting screws 1 x Allen wrench 1 x DC plug with 1 x Camera 3 x Screw anchors 1x Rubber seal terminal block Dimensions Applying the Rubber Seal Rubber seal 213 46 72mm If using the camera outdoors use the rubber seal To use remove the backing and apply to the camera base 2 SECO LARM U S A Inc Overview Camera Set screw ENFORCER Mini Vandal Dome Camera Mounting base Dome cover Before Starting 1 2 3 4 Please read this manual carefully and keep it for future reference Use the camera within given temperature and electricity limits Do not point the camera at the sun Heat could damage the camera even when not in use Do not mount the camera in areas exposed to radiation strong magnetic f2. attach the dome cover to the camera Use the included allen wrench to tighten the set screw securing the dome to the base Do a final test of the video camera and monitor ENFORCER Mini Vandal Dome Camera Troubleshooting Check that the camera is powered up Check that the power supply s polarity is correct Check that the monitor is powered up Check that the video cable connecting the camera to the monitor is connected properly The screen is blank e Clean the lens using a soft clean cloth Me Soreensimage ts Cm e Check that the light source is adequate e Adjust the monitor s contrast knob T i iti he screen image has poor contrast e Change the position of the camera The screen image flickers e Change the position of the camera The screen image is distorted e Change the position of the camera The camera case is hot e Check that the correct power supply is in use IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national state and local laws and statutes related to monitoring and recording audio and video signals SECO LARM will not be held responsible for the use of this product in violation of any current laws or statutes WARNING Stop using the camera if you see a malfunction such as smoke or unusual heat as it could cause fire or electric shock Do not open the case of this device as there are no field serviceable components i
3. ields or strong electrical signals Installation 1 Run hidden cables from the video source and 12VDC power supply to the camera Do not cut the DC jack or female BNC connector as this will void the warranty If needed use the included SECO LARM DC plug with terminal block Test to make sure the voltage is correct Use only 12VDC Undo the set screw on the side of the dome cover using the included allen wrench and remove the dome from the base lf mounting outdoors apply the rubber seal to the base as shown on page 2 Applying the Rubber Seal SECO LARM U S A Inc Wiring notch O1 x m eae Female BNC connector DC plug with terminal block mo Important Do not cut DC jack or female BNC connector as warranty will be voided Do not drop the camera or subject it to strong vibrations Note Many video monitors produce strong electromagnetic fields close to the display CRT especially when the monitor is turned on or during de gaussing which occurs automatically with many monitors when turned on Hold the camera against the wall ceiling or other mounting surface while watching the monitor to find the best mounting location Mark that location with a pencil Mount the mounting base to the wall using the 3 included mounting screws If necessary use the included screw anchors Adjust the camera angle as needed Test the video signal Re
4. nside FCC COMPLIANCE STATEMENT Information to the user This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and
5. the purchaser s exclusive remedy shall be limited to replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damages of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2011 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com al PICSN4 Tel 800 662 0800 949 261 2999 E mail sales seco larm com mi EV 2125 x2W0 1103 docx 4 SECO LARM U S A Inc
Download Pdf Manuals
Related Search