Home

Sebo 350e User's Manual

image

Contents

1. 6002 PO 890 DEOH AO 21 0110 YM H q dils uou ALDp ysnig ajqesor de dius usniq YIPIM Usnig Jo ow usnig sjiejog 21 2 Instruction Manual Power Head SEBO 350e SEBO Australia Unit 11 55 Fourth Ave Blacktown NSW 2148 Ph 61 0 2 9678 9577 Fax 61 0 2 9678 9755 www sebo com au Preparation Never run over the cable vvith the povver head Alvvays carry the machine over steps and sills Slot the suction tube 2 into the adaptor 1 tighten the two screws Then fix the cable with the six cable clips to the tube and the hose Press the button and slot the adaptor into the swivel neck 3 until it locks To release machine from upright position 4 press down foot pedal 5 The electronic brush controller monitors the operation of the brush Green light Brush correctly set and running Green light and red light The brush strip is worn out and must be changed Red light The brush has become blocked and is not turning Switch off unplug from the mains and clear the blockage Caution Always unplug machine at mains outlet before dismantling any part of the machine To replace brush strip Remove brush strip cover 34 Turn brush roller so that the brush strip can then be pulled out Ensure that the new brush strip is fully inserted Replace the brush strip before the bristles wear down to the level of the support rod
2. Caution vvork detailed belovv should only be Service nstructions carried out by persons qualified to repair electrical appliances l To remove the povver head cover 33 take off the brush strip access cover 34 remove the four large screvvs 9 from underneath the chassis Then vvith the svvivel neck lovvered and the red reset button 25 pressed in lift off the cover VVhen removing brush roller and drive belt 16 Remove bearing plate 14 Unloop the belt from the motor pulley 19 Alvvays lift out roller and bearing blocks evenly When replacing loop the drive belt over the clutch and the pulley insert left hand bearing block in its slot first then push both bearing blocks downwards keeping the brush roller parallel with the chassis To remove the brush roller pulley 32 hold the roller in one hand and turn the pulley in a clockwise direction To remove the motor pulley 19 insert a screwdriver into a groove and give a light tap in an anti clockwise direction The loosened pulley can then be removed To remove the swivel neck take out the two small screws from underneath the chassis near the voltage label then lift the swivel neck assembly from the chassis The plastic bearings 27 can be removed by pulling them off When replacing a plastic bearing ensure that it is fully pushed home over the four sections on the swivel neck To remove the swivel neck cover 24 take out the retaining s
3. crew depress the plunger 22 and slide the cover downwards When replacing ensure that the spring is in place and that the cover is pressed fully down then pushed back into its original position To remove the axle assembly unscrew the three screws and take off the axle clamps Before replacing lightly grease the axle To replace hook one end of the spring on the axle the grip the other end with a pair of pliers and turn about a quarter of a turn Keeping the wheels at the ends of the axle press the axle assembly back into place Parts List 19 18 17 33 20 25 26 27 21 24232522 32 34 30 31 11 2928 Item Part 7 Description 1 2008 Axle 350 assembiy 2 2012 ER VVheel 3 2010 Spring 4 2009 Axle 350 5 2011 Foot pedal 6 0308 End clip 7 0102 Screw F 3 9 x 13 DIN 7981 8 2014 Axle clamp 9 0110 TL Screw AM 5 x 25 DIN 7985 10 2002 svv Chassis 350e cpl incl Pos 11 12 11 2005 ER Metal plate 350 Set 12 2007 svv Bumper 350 13 2476 ER Printed circuit board 14 2079 Bearing plate 16 2049 Drive belt 17 2101 ER Brush motor 240 V 150 VV 18 05084 S Carbon brush set brush motor 10 1 2025 Motor pulley 20 2477 sv Swivel assembly 350e 21 0821 Wire on swivel 350e 22 2438 sw Pluger button cpl 23 2423 Spring 24 2022 sw Swivel neck cover 25 2016ER Swivel neck support 350 No No Description 26 0155 VVasher 27 2467 Plastic bear
4. ing inside 28 2030 ER Brush assembiy cpl incl Pos 29 29 2046 Brush strip 2046 H Brush strip hard optional 30 2091 Bearing block L H 31 2047 Bearing block R H 32 2458 Brush roller pulley 33 2482 hg Povverhead cover 34 2058 Brush strip cover 35 2450 Adapter 32 mm no cable 36 2413 Adapter 32 mm 37 0131 Nut M4 ST DIN 562 38 0117 Screw AM 4 x 12 D N 84 39 1035 svv Grommet 40 1020 Contact cover 41 0105 Screvv 3 9 x 19 D N 7981 42 0812 Plug socket 43 0502 Terminal block 2 vvire 44 0103 Screw 3 9 x 16 D N 7981 45 1030 UL Cable clamp 46 2417 Cover for adapter 47 2483 Cord straps 48 2407 NAY Cable

Download Pdf Manuals

image

Related Search

Related Contents

UKS8116-ROT - EUSSO Technologies, Inc.  Valueline VLTP90200I50 telephony cable  TF456WGH  ADL110 User Manual  Calligaris AIRPORT ONE  Motorola DSR205 Satellite TV System User Manual  

Copyright © All rights reserved.
Failed to retrieve file