Sanyo VCB-3444 User's Manual
Contents
1. in particular when using auto iris power zoom lenses sold separately If that is the case adjust the flange back position as described below l Before installing the lens check that the two flange back lock screws have been tightened If the flange back lock screws are loose the CS mount ring will not be secured and it will not be possible to adjust the flange back Fully install the lens then loosen the two flange back lock screws Set the zoom lens to the maximum telephoto position TELE then set the focus using the focus ring on the lens Set the zoom lens to the maximum wide angle position WIDE then set the focus by turning the CS mount ring Repeat steps 3 and 4 until the image stays in focus when changing from a telephoto shot to a wide angle shot When the setting is complete tighten the two flange back lock screws Ui SUN 8 English CONNECTIONS gt gt 3 2 Video signal connections po VIDEO IN B VIDEO OUT Besiccomedionfornonitoringor remiding The peripheral devices VCR monitor lens etc and cables are Insert the plug of this power cord into a wall outlet sold separately The POWER indicator A will light Adjust the picture on the 1 Make the video signal connection between the camera and the monitor using the Brightness and Contrast controls it time VCR AEDEM dM Coaxial cable type and ma2. DC power source In general this type of lens is referred to as DC type coil lens or DC type non amplifier lens Set the Auto iris lens switch to the DC position VIDEO type auto iris lens A lens with amplifier circuit that operates on video signal and DC power source In general this type of lens is referred to as EE amplifier type lens ALC and LEVEL volume level controls are available on the lens for iris adjustments Set the Auto iris lens switch to the VIDEO position Compatible auto iris lenses 1 3 inch Sanyo DC type lens VIDEO type lens VCL CS8LY Standard angle f 8 mm Standard angle f 9 mm VCL CSALY Wide angle f 4 mm Telephoto angle f 12 mm VCL CS2LY Ultra wide angle f 2 8 mm More telephoto angle f 16 mm M If using a VIDEO type auto iris lens Set the ALC and LEVEL controls on the lens to adjust the iris Normally the ALC volume should be turned all the way to Av Average Depending on the type of lens used the lens may not perform properly In such a case adjust the LEVEL volume on the lens casing to correct 6 English MOUNTING THE LENS mount type lens 2 CS mount type lens English 7 Please use a DC type auto iris lens sold separately Checking the lens mount Do not use a lens if length L is more than 9 mm If not that may damage the camera and prevent proper installation Remove the lens mount cap from the camera In
3. THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE For the customers in Canada This Class B digital apparatus complies with Canadian ICES 003 Pour la clientele canadienne Cet appareil numerique de la Classe B est conforme a la norme NMB 003 du Canada This installation should be made by a qualified service person and should conform to all local codes This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna ncrease the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV te
4. the 0 position This sets the electronic shutter speed to 1 60 sec The switch can be set as indicated in table A to select one of the 8 speeds available CAUTION When using the high speed electronic shutter the EI AI switch must be set to the AI position Using the high speed electronic shutter indoors with low lighting will give darker pictures In such a case add some lights to make sure the lighting is sufficient If the lighting is very bright pay attention to the light angle in order to avoid or minimize the smear phenomenon effect Table A 0 1 2 3 4 5 6 7 1 60 1 100 1 250 1 500 1 1000 1 2000 1 4000 1 10000 Unit sec E Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor there may be a vertical roll of the images when switched In such a case set as described below l setthe INT LL switch to the LL position 2 Switch the display on the monitor from camera 1 to camera 2 Adjust the PHASE volume on camera 2 until the vertical roll of the image stops If more than two cameras are used please repeat this procedure for all the cameras N ZA HC AR CAUTION If the vertical roll cannot be corrected by setting the PHASE volume on camera 2 try setting the PHASE volume on camera 1 If it still cannot be corrected please check that the polarity of the power cords of all connected devices is correct 12 English TROUBLESHOO
5. Bl Dimensions CD Lens iris plug 4 PC jus T Hexagonal wrench sssssssssseteeeeeeneed DC nr nm 000000 29 EL TIU p 40 1 4 20 UNC 28 Features and specifications are subject to change without prior notice or obligations English 15 SANYO INDUSTRIAL VIDEO B W VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user s expense unless specifically stated otherwise in this warranty The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll free number listed below For product operation authorized service center referral service assistance or problem resolution call CUSTOMER INFORMATION 1 800 421 5013 Weekdays 8 30 AM 5 00 PM Pacific Time For accessories and or parts call PARTS ORDER INFORMATION 1 800 726 9662 Weekdays 8 30 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA EXCLUDING ALL U S TERRITORIES AND PROTECTORATES THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END USER THE ORIGINAL DATED BILL OF SALE SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER A
6. SANYO INSTRUCTION MANUAL VCB 3444 B W CCD Camera Depending on the conditions of use installation and environment please be sure to make the appropriate settings and adjustments If you need help with installation and or settings please consult your dealer CONTENTS INFORMATICN TO FFECAUTICINS rrr aguanta DN 1 rra we zaa zaa zaa KE p t t NWA MOUNIINGTHELE ees a aazzazzaze e zana aa aaa A EMNE R 5900 SPEOFIONICNB English 1 GEUBONAWN FEATURES Built in interline transfer method 1 3 CCD approx 270 000 picture elements Low smear anti blooming low lag no burning and no geometric distortion using the CCD solid state image device 100 solid state components giving excellent immunity to shock and vibration Not subject to interference from magnetic or electrostatic fields High sensitivity minimum required illumination of 0 05 lux with F1 2 lens Horizontal resolution more than 400 TV lines Backlight compensation function Active when using an auto iris lens Externally adjustable flange back mechanical focus Low power consumption and quick start Power supply 24 V AC operation INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT WARNING TO PREVENT
7. T THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty The warranty period commences on the date the product was first purchased or rented at retail LABOR PARTS IMAGE DEVICE 3 YEARS 3 YEARS 3 YEARS EXCLUSIONS This warranty does not cover A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts batteries or routine maintenance This warranty does not apply to uncrating setup installation removal of the product for repair or reinstallation of the product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized Service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear an
8. TING Before taking the camera for repairs please check below to make sure that the camera is used correctly If it still does not perform correctly please consult your dealer or a Sanyo Authorized Service Centre No picture on the monitor screen Is the power turned on to all connected devices Is the voltage correct Are all the signal connecting cables correctly connected sthe lighting sufficient Hasthe lens cap been removed Is the lens type DC or VIDEO correctly selected Depending on the type of lens the A 1 LENS switch must be set accordingly Is the iris control correctly set A When using a DC type lens the LEVEL volume should be adjusted B When using a VIDEO type lens the LEVEL volume on the lens should be adjusted EM The picture is not clear sthe monitor correctly adjusted sthe flange back position correctly set sthe lens focus correctly adjusted Are the lens surfaces clean If there is dust or finger prints on the lens the image quality will deteriorate To clean the lens use a soft cloth or a commercially available lens cleaning set English 13 SPECIFICATIONS Scanning system Interlace Image device Picture elements Effective picture elements Synchronizing system Resolution Video output level Video S N ratio Minimum required illumination incandescent lighting Backlight compensation Iris function High speed electronic shutter Electronic iris rang
9. chnician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Sanyo may void the user s authority to operate this camera 2 English PRECAUTIONS Wi In case of problem Do not use the camera if smoke or a strange odour comes from the unit or if it seems not to function correctly Disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre ll Do not open or modify Do not open the cabinet as it may be dangerous and cause damage to the unit For internal settings and repairs consult your dealer or a Sanyo Authorized Service Centre Wl Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera If used with a foreign object inside it could cause a fire short circuits or damages If water or a liquid gets inside the camera disconnect the power cord immediately and consult your dealer or a Sanyo Authorized Service Centre Be careful to protect the camera from rain sea water etc W Be careful when handling the unit To prevent damages do not drop the camera or subject it to strong shock or vibration M Install away from electric or magnetic fiel
10. d tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED WITH REGARD TO THIS PRODUCT INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL SFC S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER ARISING OUT OF OR IN CONNECTION WITH THE SALE USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR S NEGLIGENCE ALLEGED DAMAGED OR DEFECTIIVE GOODS WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT ATTENTION For your protection in the event of theft or loss of this product please fill in the information below for you own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased SANYO 1AC6P1P2433 21605 Plummer Street L73Q4 US 0501KP TVS Chatsworth California 91311 98230002 Printed in Taiwan
11. ds If installed close to a TV radio transmitter magnet electric motor transformer audio speakers the magnetic field they generate will distort the image English 3 E Protect from humidity and dust To prevent damages to the camera do not install it where there is greasy smoke or steam where the dampness may get too high or where there is a lot of dust ll Protect from high temperatures Do not install close to stoves or other heat generating devices such as spotlights etc or where it could be subject to direct sunlight as that could cause deformation discoloration or other damages Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may raise to high levels Install where the temperature range will stay between 10 and 50 C no condensation Bi Cleaning Dirt can be removed from the cabinet by wiping it with a soft cloth To remove stains wipe with a soft cloth moistened with a soft detergent solution and wrung dry then wipe dry with dry soft cloth Do not use benzine thinner or other chemical product on the cabinet as that may cause deformation and paint peeling Before using a chemical cloth make sure to read all accompanying instructions Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time as that may cause damage or paint peeling PARTS NAMES Power indicator POWER Comes on when the power
12. e Flange back AGC Gamma correction Lens mount Environmental conditions EIA standard 525 TV lines 30 frames sec 2 1 interlace 1 3 inch solid state image device CCD 542 H x 494 V 512 H x 492 V Internal sync INT Line lock LL manually switchable 400 TV lines horizontally 350 TV lines vertically 1 0 Vp p 75 ohms composite More than 50 dB Approx 0 05 lux with a F 1 2 lens Approx 0 07 lux with a F 1 4 lens Manual ON OFF switching zone light measuring system Active when using an auto iris lens Manual ON El OFF Al switching 8 speeds selectable by switch 1 60 1 100 1 250 1 500 1 1000 1 2000 1 4000 1 10000 sec 0 07 lux to 42 000 F 1 4 lens 0 05 lux to 30 000 F 1 2 lens 12 5 mm 0 8 mm Manual ON OFF switching y 0 45 CS mount Temperature 10 C 50 C Humidity less than 90 no condensation Power supply Power consumption Weight SERVICE 24 V AC 60 Hz 4 0 W with auto iris lens 3 7 W without auto iris lens Approx 560 g without lens This camera is a precision instruments and if treated with care will provide years of satisfactory performance However in the event of a problem the owner is advised not to attempt to make repairs or open the cabinet Servicing should always be referred to your dealer or Sanyo Authorized Service Centre 14 English SPECIFICATIONS ACCESSORIES
13. ects pay attention to the light angle in order to avoid or minimize the smear phenomenon effect f conditions are outside the electronic iris operation range or more than the maximum illumination it will cause saturation of the CCD In that case use a manual iris lens 10 English SETTINGS M Lens iris adjustment If using a DC type auto iris lens you will need to set the LEVEL volume when shooting in the conditions described below L counterclockwise To decrease the contrast H clockwise To increase the contrast If shooting simultaneously in a dark room H and through a bright window f the subject background is extremely LEVEL bright or dark f the brightness of the picture on the L monitor is not correct English 11 M Backlight compensation setting Use an auto iris lens and set the BLC switch to the BLC ON position to engage the BLC ET OFF backlight compensation function lt If using a VIDEO type auto iris lens The ALC volume on the lens should be turned all the way to Av Average If the backlight compensation function does not compensate properly for the conditions set using the LEVEL volume on the lens E setting AGC Automatic gain control can be turned ON or OFF AGC ON Auto gain control OFF Fixed gain AGC ET OFF SETTINGS E High speed electronic shutter setting Normally the speed setting switch for the high speed electronic shutter set to
14. stall the auto iris lens CS mount type lens Carefully align the lens mount with the camera opening then turn the lens slowly to install it mount type lens To allow for flange back adjustment install the C mount adaptor option on the lens mount then carefully align the lens mount with the camera opening and turn the lens slowly to install it Connect the lens plug to the lens iris output connector LENS on the side of the camera When using lenses from other makers the plug shape may not correspond to the terminal on the camera In such a case remove the original plug and using a soldering iron connect the supplied lens iris plug according to the diagram Refer to page 8 MOUNTING THE LENS E Rewiring the lens cable in the lens iris plug l Prepare the lens cable Cut the cable at the plug then remove approx 8 mm of the cable sheath and strip about 2 mm from each wire 2 Install the lens iris plug Solder the cable to the pins following the correct pin layout refer to the table and illustrations then close the plug cover Pin layout DC type lenses VIDEO type lenses Brake coil 10 V DC 50 mA max Brake coil Not used Drive coil Video output 1 0 Vp p high impedance Drive coil Ground for video signal and DC power M Flange back adjustment If the pick up surface is not correctly positioned with relation to the lens focal point the picture will be out of focus
15. to the camera is on Camera setup section Internal sync INT Line lock LL setting Electronic iris El Auto iris Al setting Backlight compensation BLC setting Automatic gain control AGC setting i Line phase adjustment volume PHASE When using two cameras or more the image on the monitor may roll vertically when switching sources This rolling can be minimized by turning this volume Q High speed electronic shutter switch SHUTTER Video output connector VIDEO OUT BNC type Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector Q 24 V AC input terminal 24 V AC GND Lens iris level volume LEVEL Auto iris lens switch DC VIDEO Lens iris output connector LENS 4 English PARTS NAMES Flange back lock screw Lens mount cap The cap is installed to protect the lens mount section Remove the lens mount cap before installing a lens sold separately D Camera installation bracket The bracket can be fixed at the top or bottom of the camera Camera mounting screw hole 1 4 20 UNC CAUTION When installing the camera support select a location that can support the total weight of the camera and accessories English 5 PARTS NAMES ll Concerning auto iris lenses DC type auto iris lens A lens without amplifier circuit that operates only on a
16. ximum length 2 Connect to 24 V AC UL listed class 2 power supply sold separately Cable type RG 59U 3C2V 250 m maximum Cable type RG 6U 5C 2V 500 m maximum CAUTION Cable type RG 11U 7C 2V 600 m maximum To prevent camera and or power supply failure pay close attention to polarity when making the connections CAUTION The RG 59U type cable should not be run through electrical conduits or through the air Using CCTV Video grade coaxial cable To prevent fire hazard any UL listed wire rated VW 1 should be used for the 24 V AC cable input terminal English 9 SETTINGS Camera setup section INT L EI LL El AI BLC OFF AGC EL OFF Internal sync INT Line lock LL setting Electronic iris El Auto iris Al setting Backlight compensation BLC setting Automatic gain control AGC setting M Iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop Set the EI AI E ET A Switch to El position When using an auto iris lens for indoor outdoor use Set the EI AI switch to the AI position Note The electronic iris is suitable for normal indoor use When the EI AI switch is set to the El position do not use an autoris lens If used under fluorescent light the image may flicker In such a case change to incandescent lighting or set the EI AI switch to the Al position and use an auto iris lens When shooting bright subj
Download Pdf Manuals
Related Search