Sanyo CCA-BC200 User's Manual
Contents
1. GUIDE LINE ADJUSTMENT AFTER REAR VIEW CAMERA INSTALLATION The guide lines on the screen need to be aligned with the image taken from the rear view camera and other reference items so that the system is correctly matched to the vehicle There are seven reference items to align including 1 View from top angle alignment 2 Center line alignment 3 View from top height alignment 4 Left right guide lines alignment 5 Right guide line alignment 6 3 ft guide line alignment 7 1 5 ft guide line alignment During the alignment process the screen automatically changes to the view from top and all the alignment parameters are automatically reflected in the digitally corrected rear view CAUTION e Install the Rear View Back up Camera system in a safe place away from other vehicles and pedestrians Set the emergency brake and block the wheels so that the vehicle does not move while aligning the system If the vehicle deviates and the alignment is done incorrectly it could result in an accident Preparation before performing alignment procedure The following auxiliary items are required for alignment Prepare them in advance 1 Locate an area with parallel lines painted on a tarmac or similar flat surface such as a parking lot A i Oe 2 Prepare markers to indicate the center line of the j Center marker vehicle 6ft 3 Prepare two markers to indicate the width of the Markers2. ignition switch is turned off e The rear view of the vehicle is not displayed while the vehicle is not in reverse Need help Call 1 800 421 5013
3. N L D a Standard rear view Digitally corrected rear view Left right guide lines Green Guide lines to indicate width of vehicle Ia g 6 ft guide line Light blue 3 ft guide line Yellow 1 5 ft guide line Red View from top lt Virtual camera 2 View from top height alignment Camera The view from top height can be set by alignment of the y virtual camera For alignment process refer to Step 3 F on page 20 Virtual camera 1 View from top View from top Virtual camera 1 Virtual camera 2 Offset Calibration If the camera is not installed in the center rear of the vehicle the offset can be corrected using the alignment function ore e ZAN Need help Call i 1 800 421 5013 if i j Standard view View from top Deviated center Corrected center CAUTIONS FOR CONNECTION A CAUTION e Before connecting disconnect the negative battery terminal Connect the negative battery terminal after all other connections are completed e Connection terminals and cables are differentiated by color Make connections to the same colors Make sure connectors are securely inserted until a click sound is heard Incomplete connection may cause a distorted picture or operation errors e Before disconnecting the connector turn the ignition switch to the off position Otherwise it may cause a malfunction When dis
4. Need help Call eats Cis eed help Ca a meai 1 800 421 5013 Note e The camera can also be installed in the taillight license plate area or on the rear window lt Taillight license plate area gt lt Rear window gt INSTALLATION Installing system on rear spoiler Sa 1 Clean the location where the camera is to be installed Wipe off oil wax moisture dirt and dust using a cleaner and a clean cloth 2 Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to a flat surface on the rear spoiler X Press the bracket with a finger to assure good contact of ie eee the bracket to the surface of the vehicle Touching the Bracket N SA sticky surface of the tape with a finger or re adhering the int Y bracket will weaken the adhesion strength and result in a i Y loose installation that could eventually fall off e f the temperature where the camera bracket is to be installed is low warm the area with a hair dryer so that the tape adheres firmly to the surface Do not apply heat to the camera or the lens A CAUTION e Mount the camera level with the e Position the lens axis of the camera vehicle and ground surface square to the vehicle in order to obtain a correct rear view 3 Install the camera to the bracket using the screws Install the camera SANYO logo facing upward Brack
5. Use of these chemicals or cleaners will cause deformation deterioration or damage to the system Do not wipe any part of the system with cleaners containing polishing or abrasion agents as they will cause scratching If the lens becomes soiled wipe lightly with a soft clean cloth soaked in water Wiping with excessive force using a dry cloth could cause scratching Do not scratch or nick the camera cable Water or moisture penetrating the camera via a crack or opening in the camera could cause electrocution fire or other irreparable damage If the vehicle is to be washed with the camera installed avoid water directly contacting the cable area to prevent water from penetrating into the vehicle cabin Do not allow highly pressurized water from automatic car washing machines or high pressure car washers to contact the camera unit Otherwise the camera could fall off or water could penetrate the camera unit due to an inability to maintain a waterproof seal which could result in electrocution fire or other irreparable damage Inspect the camera and cables periodically Verify that the installation screws have not become loose or the installation bracket is not separating from the installation surface Tighten any loose screws If the camera falls off and hits a pedestrian it could result in an accident or injury If direct sunlight or strong light sunlight reflected from the bumper or headlights is directed at the camera lens it could caus
6. flashing light blue rectangle 6 1 Each time the control switch is pressed the 3 ft guide line moves farther from the vehicle Continuously pressing the control switch moves the line farther away until it exceeds a certain range and the line returns to the position closest to the vehicle Set the 3 ft guide line to match the 3 ft marker fe 6 2 Press and hold the control switch for more o m m o m m than two seconds ty The 3 ft guide line alignment is now set and the screen changes to the 1 5 ft guide line alignment setting The 1 5 ft guide line is indicated in red on the screen 7 1 5 ft guide line alignment flashing blue rectangle 7 1 Each time the control switch is pressed the 1 5 ft guide line moves farther from the vehicle Continuously pressing the control switch moves the line farther away until it exceeds a certain range and the line returns to the position closest to the vehicle Nr Osposee TN Set the1 5 ft guide line to match the 1 5 ft marker 7 2 Press and hold the control switch for more than two seconds The 1 5 ft guide line alignment is now set and also 6 ft guide line alignment is now set automatically and all the alignment settings are now completed The screen will disappear after displaying the view from top for three seconds Note e The 6 ft guide line may not display as a result of camera installation conditions 8 Aft
7. only at the image appearing on the screen Always confirm the safety of the rear of the vehicle and its surrounding by using both the rear view mirror and the door mirrors in combination with the rear view camera The actual position and distance of persons or objects appearing on the screen may differ depending on the properties of the camera lens Regarding use Do not knock the camera or allow it to be hit forcefully by an object Otherwise it could result in the camera being damaged Exposing the camera lens to extreme temperature change via a direct flame hot drier or hot water could break or damage the camera lens Do not allow the camera lens to capture images of direct sunlight for long periods of time Otherwise it could leave permanent impressions on the screen The screen image could distort at the moment the rear view image is displayed differs depending on the monitor model connected to the system The image will stabilize soon afterwards If the system is used for a long period of time white streaks and lines will appear due to increased temperature however because of the CCD properties the system will not be damaged Screen flicker may occur while in fluorescent lit areas utilizing 50 Hz power supplies however this will not cause damage to the system Do not wipe the camera unit and lens area installation bracket or camera cable with volatile chemicals or cleaning agents containing alcohol benzene thinner or gasoline
8. switch in the ON position for long periods of time the battery power could be depleted A CAUTION e f no picture appears on the screen turn the monitor power on and change the input selector so that the screen of the rear view back up camera system appears Check the connection between video output terminal of ECU box and the camera or video input terminal of the monitor Refer to the manual for the monitor Notes e If no alignment procedure is commenced for three minutes or longer the system turns the image off and the set parameters will NOT be stored e Do not leave the ignition switch in the ACC ON position for a long period of time as it could deplete the battery power e Black triangles at the bottom on both sides appear when the display mode is set to View from top This does not indicate a malfunction In addition depending on the center line alignment position the size of each of the triangles could differ Alignment Note Follow the alignment procedures in the indicated order from 1 to 7 Each of the below alignment steps is indicated by a flashing rectangle corresponding to each alignment item moving from left to right with each rectangle having a different color View from top angle alignment White Center line alignment Red View from top height alignment Violet P Left right guide lines alignment Yellow E Need help Call Right guide line alignment Green 1 800 421 5013 3 ft guide line alignment Ligh
9. to indicate width of vehicle vehicle 4 Ruler to measure 1 5 ft and 3 ft and two markers A e Cans or bottles make good markers Marking tape es j Sit mater for alignment is provided with this Rear View Back i up Camera System to indicate 1 5 ft and 3 ft guide l 5 ft 1 5 ft marker lines and the width of the vehicle y S YY Park the vehicle parallel to the parking space lines and g place markers shown in the right figure alge L Need help Call 1 800 421 5013 Align ment Mode Seven rectangles at top left indicate seven items to align Turn the ignition switch to the ACC ON position while depressing the control switch e Press and hold the control switch until the screen appears View from top alignment screen appears Seven rectangles at top left indicate seven items to align If adjustment mode cannot be selected 1 Turn the ignition switch to the ACC ON position while pressing the switch Press and hold the switch for two seconds or more 2 Turn the monitor on so that rear view images captured by the camera can be seen e If any view is not displayed on the screen turn the ignition switch to the ON position without starting the engine and set the shift lever to R reverse e Depending on the navigation system or external monitor connected to this accessory the operation can be interlocked with the reverse gear e If the vehicle is left with the ignition
10. SANYO INSTRUCTION MANUAL CCA BC200 Rear View Back up Camera System CAUTION e Installation and wiring require technical expertise and experience To ensure proper installation and safety consult the dealer where the product was purchased SANYO S HELP LINE Call the toll free number below if you have any difficulties operating this product 1 800 421 5013 Weekdays 7 30 AM 5 00 PM Pacific Time REAR VIEW BACK UP CAMERA SYSTEM MODEL CCA BC200 LIMITED WARRANTY FOR SERVICE ASSISTANCE CALL Customer Information 1 800 421 5013 Weekdays 7 30 AM 5 00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED AND USED IN THE UNITED STATES OF AMERICA THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL USER AND DOES NOT APPLY TO PRODUCTS USED FOR ANY INDUSTRIAL PROFESSIONAL OR COMMERCIAL PURPOSE THE ORIGINAL DATED BILL OF SALE OR SALES SLIP MUST BE SUBMITTED AT THE TIME WARRANTY SERVICE IS REQUESTED Subject to the OBLIGATIONS above and EXCLUSIONS below SANYO FISHER COMPANY SFC warrants this SANYO product against defects in materials and workmanship for the periods of LABOR and PARTS specified below SFC will repair or replace at its option the product and any of its parts which fail to conform to this warranty with new or reconditioned products or parts The warranty period commences on the date the product was first purchased at retail EXCLUSIONS This warranty does not cove
11. SPLAY AND SWITCHING DISPLAY MODES ssee2 0 23 SAFETY PRECAUTIONS lt Safe and correct use of the product gt e Before using the rear view back up camera read this instruction manual for proper use of the product as directed e Sanyo and its suppliers are not responsible for damage or malfunction that arises from the failure to follow the instructions in this manual Please be aware that the manufacturer s warranty may be invalid if the procedures in this instruction manual are not followed properly e After using this instruction manual store it in a place where it can be easily located A WARNING indicates a situation in which serious injury A WARNING or death could result if the warning is ignored A CAUTION indicates a situation in which bodily injury CAUTION or damage to objects or both could result if the caution is ignored A WARNING e Be sure to disconnect the negative battery terminal when wiring Electrocution or injury due to a short circuit could occur e This Rear View Back up Camera System is for exclusive use with DC 12V negative ground vehicles Do not use this Rear View Back up Camera System on DC 24V vehicles such as trucks buses A fire or other damage could occur e Do not install this Rear View Back up Camera System in a location that blocks the rear view or obstructs the operation of the steering wheel shift selector lever or brake pedal when driving or jeopardi
12. UE TO CAUSES BEYOND ITS CONTROL SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE For your protection in the event of theft or loss of this product please fill in the information below for your own personal records Model No Serial No Located on back or bottom side of unit Date of Purchase Purchase Price Where Purchased CONTENTS SAFETY PREGAUTIONS ite a a tected A A A A ati tins ORE ATR 2 GPEGIFIGATION E Er E E N E A E a o 4 BEFORE USING THE REAR VIEW BACK UP CAMERA SYS EM eeeeeeeeretreerererererese 5 ACCESSORIES AND HARDWARE vssssssssssesseseesesesseescsessesscseseesscseseesssseseesssseseessseesssseseessens 6 REAR VIEW BACK UP CAMERA SYSTEM OUTLINE r eesesseseesesreseeseseeseeeeeeesceeeseescseeseeaeees 7 CAUTIONS FOR CONNECTION o secserseresttesteeteetetenceeseseeeeeeceeceesescssesseseeseeseeceesteeseeeeeseeeees 8 CONNECTION Ea eaa et0it soc E E T E etre esta E E eters eats 9 BEFORE INSTALLATION a n e EEEE EEEE A ER ea EEE 10 INSTALLATION o eia ea e E A E A A 12 CABLE ROUTING eresi ti ineens nnns keane An ENEE EE EEES aE SEE MEERES ENESE ENN ARESE EE aN EE CERA as 15 GUIDE LINE ADJUSTMENT AFTER REAR VIEW CAMERA INSTALLA ION eee 17 REAR VIEW CAMERA DI
13. adhered to the surface the camera bracket might become loose and fall off When mounting the camera onto the glass surface make sure the rear wiper does not hit the camera while it operates Otherwise the camera could be damaged or destroyed Install the camera so that it does not obstruct the opening or closing of the liftgate Installing the camera in a position that obstructs vision is dangerous and could cause an accident Install the camera so that it does not obstruct the rear view or vehicle operation and make sure it does not protrude beyond the sides of the vehicle To assure that the camera remains firmly attached to the vehicle a Do not install the rear view back up camera system outdoors in rainy or foggy weather High humidity will prevent the camera from firmly adhering to the vehicle b If installation is required in areas of high humidity completely dry the surface where the camera installation bracket is to be installed c If the temperature where the camera installation bracket is to be installed is low 68 F or lower warm the location with a hair dryer so that the tape will adhere firmly to the surface Do not apply heat to the camera or the lens d Do not install on a vehicle body or glass window with a surface that has been processed with a fluorine resin coating The vehicle can be driven immediately after installation as long as the following DO NOT occur within a 24 hour period a Water is poured on the
14. connecting the connector hold the connector itself to remove it while pressing the connector lock If the cable is pulled it may come off causing a malfunction e Do not splice the power supply cable to connect it to the power source of other devices A fire or electrocution could occur due to excess current flow on the power cable e Always connect the red lead wire of the power supply cable to the accessory ACC power supply Do not connect this Rear View Back up Camera to the power supply for the camera which some navigation systems are equipped with e Connect the brown lead wire to the signal line which switches from 0 V to 12 V when the shift lever is shifted to R reverse e If a small plug socket input monitor is used a commercially available adapter is required to convert it to a pin plug The adapter can be purchased at an electric appliance shop 1 CONNECTION Rear view camera connection terminal Black Control switch connection terminal Green ECU box Video output connection terminal Yellow Connect the cable according to the color and shape of the terminal Power supply connection terminal Brown Yellow Video output cable RCA Type Connect firmly to a metal part of vehicle for grounding Connect to Camera input Yellow terminal or mle b mp video input terminal on navigation or external monit
15. d rear view is displayed e Min Required luminance Approx 1 6 Ix e Output Signal 1Vp p 75 ohm NTSC RCA type socket Operation Temperature ssseeessseerrrerrrresrsressreesrrrerrsrersrrersreerreeerreeennsenssreerseenreeernneenseeet 4 F to 140 F e Storage Temperature eeeeeeeeeeerererereeerrerererererererereteeeeserererererereeserererererereeereeseneserere 22 F to 176 F e Camera Dimensions W1 1 x HO 9 x D1 0 without protrusions e ECU Dimensions W3 4 x H1 1 x D2 6 without protrusions e Camera Weight Approx 0 35lbs including cable e ECU Weight Approx 0 37lbs Mirror image The camera produces an image on the screen with the left and right appearing reversed the same as when looking into the rear view mirror or the door mirrors e Specifications may change at any time without prior notification BEFORE USING THE REAR VIEW BACK UP CAMERA SYSTEM Regarding methods of use The Rear View Back up Camera System is a devise designed only to assist the driver The driver must take full precautions to confirm the safety and conditions around the vehicle Water droplets on the camera lens could adversely affect the image The positioning appearing on the screen changes according to the vehicle conditions number of occupants and weight of cargo Always directly confirm the safety of the rear of the vehicle and its surroundings visually while operating the vehicle Never reverse the vehicle while looking
16. e fluctuations in the light source and vertical lines streaks to appear on the screen however this does not indicate a malfunction or damage 5 ACCESSORIES AND HARDWARE Make sure all the following parts are included in the Rear View Back up Camera System kit ECU box T pe Electronic Control Unit box Bracket for camera 1 pc with double sided tape D gt Cable clamp 10 pcs gt Waterproof pad 1 pc Instruction manual 1 pc with warranty Power supply cable 1 pe approx 4 92 ft long with fuse Hook and loop fastener 1 set for ECU box amp Screw for camera 2 pcs Hexagon type M3 x 6 Double sided tape 1 pc for waterproof pad Alignment guide Control switch cable approx 8 20 ft long with double sided tape Video output cable 1 pc Hexagon wrench 1 pc Self lock conductor 1 pc for reverse signal detection Cleaning cloth 1 pc REAR VIEW BACK UP CAMERA SYSTEM OUTLINE ra T _ Virtual camera A View from top Sa rear view S a Display mode Including the standard rear view image captured by the camera a digitally corrected rear view view from top and standard rear view can be selected Guide lines are indicated in order to assist j 7 Ow oN ltl a e the driver and assure safety when backing up rf ZF 7 4 fj T A Hf WUP ERT f f ES N W sa V EN
17. er turning the ignition switch off and removing the auxiliary items used for alignment move the vehicle to a safe place REAR VIEW BACK UP CAMERA DISPLAY AND SWITCHING DISPLAY MODES Preparation prior to use Make sure the ignition switch is in the ON or ACC position CAUTION e f the image turns off automatically after the guide line alignment turn the ignition switch off then to the ACC ON or ON position prior to the following procedure 1 Turn the monitor on and select the input mode switch to view the image from the rear view camera on the screen Refer to the instruction manual for the monitor for details 2 Set the selector shift lever to R reverse A digitally corrected rear view will be visible on the screen 3 Press the control switch to change the display mode Digitally corrected rear view View from top Standard view oy a healt al BO Whe TOT TYT ENS A CAUTION The rear view back up camera system is a devise designed only to assist the driver The driver remains responsible for being aware of and confirming the vehicle surroundings For safety reasons it is important for the driver to take extra precautions when backing up Notes e After the ignition switch is turned from off to the ACC ON or ON position a digitally corrected rear view is displayed on the screen first e When changing the display mode the selected display mode remains until the
18. et using the hexagon wrench included in the product package ne Camera mounting screw Ca Need help Call Camera 1 800 421 5013 4 Adjust the camera angle so that the extreme rear end of the vehicle bumper rear window and liftgate is displayed at the bottom of the monitor Need help Call 1 800 421 5013 e After adjusting the angle tighten the screws with them seated at the lower end of the oblong holes in the bracket on each side A CAUTION After installing the camera the screen displays an approximate 135 degree view between the left and right and an approximate 105 degree view between up and down The rear view back up camera system is a device designed only to assist the driver The driver must take full precautions to confirm the safety and conditions around the vehicle 5 Locate a position to install the ECU box where all the cables are within connection reach CAUTION e Avoid installing near the ventilators for the heater 6 Peel off the paper backing from the Hook and loop fastener 1 set adhere each piece to the bottom of the ECU box and install the ECU box in the position determined in Step 5 Note e There are separate surfaces for each piece of Hook and loop fastener Attach the rough surface to the bottom of the ECU box and the soft surface to the location where the ECU box is to be installed e f the rough surface of the Hook and loop fastene
19. n accident e Do not splice the cable to connect the power supply to other devices e After completing the installation and wiring make sure the brake lights lights horn turn signals wipers and other electrical components operate properly Otherwise an accident could occur e Do not disassemble or modify the Rear View Back up Camera System Disassembly prohibited It could result in an accident fire or electrocution If foreign material has penetrated the Rear View Back up Camera System or liquid has spilled onto it which may produce smoke foul odor or abnormal noise discontinue use immediately and always consult the dealer where the Rear View Back up Camera System was purchased If the Rear View Back up Camera System continues to be used it could result in an accident fire or electrocution e f power to the power cable has been cut or a fuse has blown verify that the cable has not been shorted and replace any blown fuses with a new fuse of the same current rating Ampere is displayed on the fuse If a non specified fuse is used a fire or malfunction could occur e Be sure to route wiring so that it does not come into contact with heated parts Otherwise the wire covering will melt and cause a short resulting in a fire or electrocution e Do not use this Rear View Back up Camera System if it appears damaged such as when there is no display or sound output Otherwise it could result in an accident fire or electrocution e Dono
20. or Rear view camera eN 2 Control switch Control switch cable Connect to the reverse signal cable of vehicle using self lock conductor included Brown with the Rear View Back up Camera System Refer to How to use self lock conductor Self lock conductor Connect to point where power is supplied at ignition switch ACC position This terminal allows connection of other accessory devices Do not remove cap sleeve when not in use CAUTION e Installation and wiring require technical expertise and experience To ensure proper installation and safety consult the dealer where the product was purchased Notes e Always use the same type of fuse with the same current rating when replacing it e When connecting to a navigation system or an external monitor also refer to the manual provided with the unit e Depending on the type of vehicle or navigation system the rear view back up camera system may not function as expected Consult the dealer where the product was purchased BEFORE INSTALLATION Rear View Back up Camera System Installation Cautions Bundle cables with tape or string so that they do not obstruct driving Cables that become entangled in the steering wheel shift selector lever or brake pedal could cause an accident Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to the surface of the vehicle If the tape is not completely
21. r A the adjustment of customer operated controls as explained in the appropriate model s instruction manual or B the repair of any product whose serial number has been altered defaced or removed This warranty shall not apply to the cabinet or cosmetic parts antenna knobs batteries or routine maintenance This warranty does not apply to uncrating setup installation and removal of the product for repair or reinstallation of the product after repair This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including but not limited to any malfunction defect or failure caused by or resulting from unauthorized service or parts improper maintenance operation contrary to furnished instructions shipping or transit accidents modification or repair by the user abuse misuse neglect accident incorrect power line voltage fire flood or other Acts of God or normal wear and tear The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS IS LIMITED TO THE TERM OF THIS WARRANTY IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY D
22. r attached to the bottom of the ECU box adheres to floor without need for the mating piece attach the ECU box directly to the vehicle floor without using the mating piece Loosen D f Extreme rear end of vehicle A bumper etc Tighten CAUTION e Verify the tightness of the screws and tighten them more if necessary m ays sli z f ae rn ee S CH J SA n Hee IN OEA J A A M ALT HE A AH SV e ECUbox ECU box Hook and loop fastener Soft side Floor Hook and loop fastener Rough side 7 Install the control switch in a position where it is easy to operate Peel off the paper backing on the back of the control switch and attach it to a suitable position CAUTION Do not install the control switch in a position that obstructs vehicle operation How to use self lock conductor 1 Insert the reverse signal cable of the vehicle into the self lock conductor 2 Fold the self lock conductor and lock the reverse signal cable 3 Insert the reverse signal pick up cable Brown included with the system into the self lock conductor Insert the cable until it stops Need help Call 1 800 421 5013 4 Close the self lock cover and firmly lock it by pinching it with pliers Control switch Cable stopper E icy a m Reverse
23. signal pick up cable included with t system Brown CABLE ROUTING The following is an example when installing the camera on the rear spoiler Control switch CAUTION Route the cable so that it does not block or obstruct vehicle operation Route the rear view camera cable as far away from the vehicle antenna as possible to prevent noise interference with AM radio band reception Also route the cable as far as possible from a TV antenna if equipped Clean the areas where the cable clamps and waterproof pad are to be attached Wipe out oil wax moisture dirt and dust with a cleaner and a clean cloth 1 Route the camera cable along the top of the liftgate and secure the cable with the cable clamps included with the Rear View Back up Camera System Straighten the cable along the top of the spoiler or liftgate and insert it through the opening at the side of the liftgate e Give the cable some slack to enable smooth opening and closing of the liftgate Cable clamp Cable clamp Need help Call 1 800 421 5013 2 Route the camera cable down to the lower part of the liftgate and secure it with the cable clamps Route the cable to the outside of the liftgate hinge and harness cover e Route the cable carefully so that the cable is not pinched when the door opens and closes e Route the cable carefully to prevent water penetration Cable tie 3 Route the camera cable to the ECU bo
24. t Blue 1 5 ft guide line alignment Blue NO groBe Nom 1 View from top angle alignment flashing white rectangle 1 1 Each time the control switch is pressed the angle increases Continuously pressing the control switch returns the alignment to the original angle ste H f 1a nO m a zN Set the parking space lines parallel to the lines on the screen 1 2 Press and hold the control switch for more than two seconds The view from top angle alignment is now set and the screen changes to the center line alignment setting The center guide line is shown in red on the screen 2 Center line alignment flashing red rectangle 2 1 Each time the control switch is pressed the screen moves to the right Continuously pressing the control switch returns the screen to the left Align the center guide line with the center Jp ae markers f 2 2 Press and hold the control switch for more eren than two seconds The center line alignment is now set and the screen changes to the view from top height alignment setting 3 View from top height alignment flashing violet rectangle 3 1 Press the control switch to change to a cmescom qeeooom higher or lower view from top Select a view from top height so that the na ee markers indicating the width of the vehicle 9 can be seen better on the screen 3 2 Press and hold the control switch for more Ome om
25. t touch this Rear View Back up Camera System during extreme weather conditions such as thunder and lightning Otherwise it could result in electrocution A CAUTION e Installation and wiring requires technical expertise experience To ensure safety consult the dealer where the Rear View Back up Camera System was purchased e Be sure to use the Rear View Back up Camera System in the specified manner If a non specified part is used the internal parts of the Rear View Back up Camera System can be damaged or detach because of improper attachment resulting in an accident e Do not install the ECU box to a location where rain moisture or dust can penetrate If water moisture or dust penetrates the ECU box it may cause fire or smoke e Do not install the ECU box where heat is retained such as under a carpet Heat from the ECU box cannot be dissipated causing a fire malfunction or deterioration e Wire the cable so that it does not touch any metallic areas The cable could be damaged from contact causing a fire or electrocution e Route wiring properly according to the instructions An incorrect connection might cause a fire or accident e Be careful and prevent the wiring harness from being pinched between the vehicle body screws or moving parts such as the seat rails It could cause an accident electrocution or fire due to an open or short circuit e The Rear View Back up Camera System is for in car use only and is not to be used ou
26. than two seconds a The view from top height alignment is now set and the screen changes to the left right OO guide lines alignment setting Left right guide oF lines are indicated in red on the screen gt 4 Left right guide lines alignment flashing yellow rectangle Teste 4 1 Each time the control switch is pressed the i T m mi i amm Ome Mm width of the guide lines becomes narrower zs bea Continuously pressing the control switch sets the screen at the maximum width Set the left guide line to match the left side marker of the vehicle 4 2 Press and hold the control switch for more than ole oe a two seconds FATE The left right guide lines alignment is now set and the screen changes to the right guideline j ee alignment setting The right guide line is indicated in red on the screen E 5 Right guide line alignment flashing green rectangle 5 1 Each time the control switch is pressed the right guide line moves towards the center Demoen odaoj am Continuously pressing the control switch a 6 moves the guide line to its maximum right position Set the right guide line to match the right side marker of the vehicle 5 2 Press and hold the control switch for more than two seconds The right guide line alignment is now set and the screen changes to the 3 ft guide line alignment setting The 3 ft guide line is indicated in red on the screen 6 3 ft guide line alignment
27. tside of the vehicle If it is used outside of the vehicle it could result in electrocution or other injury e Install the camera on the vehicle during sunny daytime hours If installed in rainy or foggy weather high humidity will weaken the adhesion strength of the double sided adhesive tape and the camera may fall off resulting in an accident or injury e Avoid moisture such as water rain fog snow or applying excessive force to the camera for 24 hours after installation The adhesion strength of the double sided adhesive tape will weaken and the camera may fall off resulting in an accident or injury e Be careful when handling the double sided adhesive tape Touching the sticky surface of the tape or re attaching the bracket weakens the adhesion strength The bracket may fall off resulting in an accident or injury e This Rear View Back up Camera System has been designed to assist the driver in confirming the rear view when backing up the vehicle into a garage or when parallel parking For safety reasons it is important for the driver to take extra precautions when backing up SPECIFICATION e Power Supply DC 12 V DC 11 V to DC 16 V Negative ground e Max Consumption Ampere Approx 300mA e Viewing System Mirror Image for vehicle reversing e Imaging Device Color CCD 14 e Number of Pixels Total 270 K pixels Effective Approx 250 K pixels e Viewing Angle Horizontal Approx 135 degrees Vertical Approx 105 degrees Standar
28. vehicle surface b The vehicle is driven in the rain c Pulling or excessive force is applied to the camera Notes e Temporarily hook up the system confirm that the system functions properly and then install it permanently e If the system does not function properly re check the connections Determination of Camera Installation Position example e Temporarily adhering the camera with the tape locate a suitable installation position by adjusting the camera angle so that the rear of the vehicle bumper and other areas is visible in the monitor e Install the camera in a position that does not allow the illumination of a high mount brake light to reflect into the camera lens e Make sure the camera does not contact or rub against the vehicle body when the rear door opens or closes e Removing and re adhering the bracket will weaken the adhesion strength e Position the camera so that it is not aimed directly at the headlights of rear oncoming vehicles The recommended installation area is shown below Installing the camera outside of this area could result in reduced camera functionality and reduced rear view visibility 15 7 in 15 7 in Recommended camera installation area Center of vehicle 70 9 in i j 2951n 1 T 9 8 in 19 8 in e Installing the camera on the rear spoiler or liftgate example lt Rear spoiler gt lt Liftgate gt
29. x positioned inside the vehicle and clamp it using the cable Luggage finish plate clamps ear Insert the cable into the slit provided in the N waterproof pad and attach the waterproof pad to i 0 1 in f J the weather strip on the vehicle at the point where nore Na OA Position with no ribs on the rear side LE the cable enters the vehicle Aare Waterproof pad Weather strip trol switch 4 Route the control switch cable to the ECU box and Conto ee EOU pox secure it with cable clamps A CAUTION e Route the cable so that it does not obstruct vehicle operation a A ne cca ba Cable clamp Confirmation of camera installation and cable routing Make sure the camera and cable do not interfere fiat when operating the liftgate and that the cable does Liftgate Z not contact the edge of the liftgate Connecting Video Cable ECU box Connect the video output cable to the camera input TS terminal or video input terminal on the navigation JOH Video output connection system or external monitor Read the separate Tt terminal Yellow instruction manuals for these devices to connect them correctly Video output a cable Yellow Navigation system or external monitor Need help Call Yellow 1 800 421 5013 eae To Video input terminal Connect to camera input terminal or video input terminal on navigation system or external monitor
30. zes the safety of other passengers Otherwise an accident or injury could occur e When installing this Rear View Back up Camera System to a vehicle equipped with air bags The name differs depending on the manufacturer such as SRS dual air bag SRS side air bag SRS curtain air bag do not install this Rear View Back up Camera System or route its wiring where it affects operation of the air bag system If the air bags do not operate properly in an emergency an accident or injury can occur Consult the dealer where the product was purchased to determine the installation position keeping safety in mind e Do not use any cables other than ones provided with this Rear View Back up Camera System Do not modify the cables e If installing this Rear View Back up Camera System or connecting the ground using the vehicle nuts and bolts never use nuts and bolts from critical parts of the vehicle such as the steering wheel brake system and fuel tank Vehicle control may become inoperative or a fire could occur e When drilling holes into the vehicle body to install this Rear View Back up Camera System check the locations of pipes tanks and electrical wiring so that this Rear View Back up Camera System will not interfere with them Otherwise a fire or other malfunction could occur e Be sure to bundle cables so that they do not obstruct driving Loose cables which become entangled in the steering wheel shift selector lever or brake pedal may cause a
Download Pdf Manuals
Related Search