Royal Sovereign 1650C User's Manual
Contents
1. COLD FILM PAPER BACK 1 Setthe glossy side of upper lower film to face the heat Glossy side is PET film and matte side is thermal polymer laminating film 2 Like picture 1 insert core into the left side of upper lower film shaft 3 Like picture 2 and 3 insert core into the right side of upper lower film 4 Like picture 4 and 5 adhere core closely Make the right left direction of fixing screw consistent 5 Locate film in the middle and then fasten core fixing screw GOLD FILM TAKE UP An PAPER BACK HOT DUE PAPER BACK N LOWER IDLE BAR 1 Set up cold film below the upper bar of the machine UPPER IDLE BAR Set the same as methord of the HOT film for protect paper of lower part 2 Set the pressure lever to the 15mm open mode 3 Insert a piece of wide cardboard guiding paper carrier between the rollers 4 Pull the film from the upper roller passing over the upper idle bar to the upper roller and put it on the upper roller 5 Put the paper back of the film to the bobbin at take up bar to rewind the paper back 6 Allow some of the film with melted resin to stick to the Guiding Paper 7 Place the film from lower shaft beneath the film from the upper roller which is already meiting and unwind films of both rollers 30 40cm 1 1 3ft for loosing the tension 8 Set the pressure lever to the 1mm 9 Set speed at 1 and press the RUN button The films will be fed into the machine and2. run backward 10 1 Put cold roll film on upper bar Set the same as methord of the HOT film for protect paper of lower part 2 Pull COLD film and fix it so that backside protecting paper can be wound on take up mandrel clockwise Revolve core to make protectingpaper tight a little bit 3 Set pressure lever at the proper position following to your lamination condition 4 After pressing the RUN STOP button choose and set proper speed by using the SPEED button or W 5 Turn on the take up device and set the proper film tension by pressing the RUN STOP button Lower tension would make better operation 10 Set pressure lever at the Hard board 15mm mode 11 Turn off the power switch Reference 1 Set up the protection paper Otherwise glue form the film will be stuck on the face of roller and it can be seriously damaged 2 Turn the switch RUN STOP and Take up motor at the same time 11 Cross Cutter 1 It is on the back side of the machine J gt 2 After lamination move cutter to a point about 1 3 of the width of lamination 3 Grasp film with one hand and press the cutter cutter downward and slide it to the direction intending to cut with another hand 4 Press the cutter and slide it the other way 12 1 Please be cautious that neck tie necklace long hair clothes are kept well away while operation 2 Prevent children from accessing the machine Ex
3. 12 FUSE 50T 8 250 6 3A RSC 1650H 5 1650 5 1650 RSC 1650C C CO x FUSE 65TS BOLT CORE AC250V 20A amp 4 d 14 1 For six month from the date of purchase Royal Sovereign International Corporation or its authorized service center will repair this product free of charge if it is defective in material or workmanship 2 This Limited Warranty does not include cleaning or damage caused by accident neglect misuse or improper installation operation or external scratch any damage caused from service maintenance modifications or tampering by anyone other than a Sovereign authorized service representative or damage caused by a natural calamity such as fire or earthquake and etc 3 Customers will bear the expense of Transportation fee and delivery fee of the damaged machine 15
4. Royal Sovereign LAMINATORS OWNER S MANUAL RSC 1650H 1650C PLEASE READ AND SAVE INSTRUCTIONS TOPICS INSTRUCTION SAFETY PRECAUTIONS CHARACTERISTICS SPECIFICATIONS NAMES OF MAJOR PARTS OF MACHINE SETTING UP FILM HANGING FILM CONTROL OF ROLLER PRESSURE lt F INSTRUCTIONS FOR CONTROL PANEL 1 FUNCTIONS OF CONTROL PANEL 2 HOW TO USE BUTTONS eo en nn nn LAMINATING STEPS METHOD FOR USING CUTTER T CROSS CUTTER S u UU IMPORTANT SAFETY CONCERNS MAINTENANCE IT S NOT OUT OF ORDER _ ASSEMBLY PARTS WARRANTY PAGE CON ON c O 22 22 aa a a ow mor A OO GO N NYO Oo o Thank you for purchasing a Royal Sovereign Roll Laminator It has been designed and manufactured to provide years of continuous service in the professional environment To insure high quality lamination please read this instruction manual thoroughly This manual will provide you with complete operating and maintenance information SAFETY PRECAUTIONS The safety recommendations outline
5. d in this section are to be read understood and followed before operating machine keep this information for future refrence Failure to comply any of the following safety procedures could result in serious personal injury To prevent the possibility of electrical shock do not immerse machine in water or permit liquids to spill inside Do not allow articles of clothing neckties scarves papers etc near front or rear machine openings as they could get caught by rollers and be pulled inside causing personal injury Do not insert sharp objects into front or rear machine openings Do not place anything in feed tray openings of machine other than appropriate laminating materials or pouches Do not attempt to laminate items that exceed total recommended material thickness Do not operate machine for any other purposes than its intended use Do not operate machine if electrical plug or power cord is damaged Turn off the power when unattended or not in use Unplug machine before moving it or when it is not in use for an extended period of time This machine is intended for indoor use only Do not alter or extend electric plug Plug is configured for appropriate electrical supply 10 The socket outlet shall be installed mear the equipment and shall be easily accessible RS Roll Laminator Line is advanced laminators with time transcendental design utilizing the latest in laminating technology It is designed for you to
6. set temperature and speed as necessary Also you can laminate anything at high speed regardless of thickness of material and type of film It is also designed for convenient use by anyone through the simple procedure of adjusting film tension in accordance with the thickness of film and materials to be laminated RSC 1650H RSC 1650C Description Power Supply 120V 60Hz 120V 60Hz Power Consumption Watts 1700 100 Max Laminating Width mm 1650 65 1650 65 25 50 75 80 100 5000 16 4ft min Laminating Thickness micron Laminating Speed mm min MEN O Ready time min Heating Method Warm Roller 2 Temp Select 9 step digital 9 step digital DC Geared Motor 2 Roller Temp Control Speed Control Driving Motor Transport Type O Cooling System Hot Lamination Photo Lamination yes Mount Lamination yes 15mm Reverse yes Stand by mode no Power auto off no Foot switch yes Remote switch yes O Laminating Length Measurement 2 O Laminating Paper Counting Dimension WxDxH mm 1960x650x1210 77 2 x25 6 x47 4 Unit Weight 230Kg 500ibs Gross Demension WxDxH mm 2100x875x1250 82 7 x34 1 x49 2 O Gross Weight 300Kg 660ibs a gt oos 4 6 HOTROLER UPPER ROLLER XxX 711 5 ML 5 9 TENSIONGONTROLKNGR S 4
7. treme Heat Will Cause Injury 3 Place the machines on the plated place in order to prevent the machine from damage 4 Make certain that the machine is connecterd to an adequate power souce 5 Do not use any other purposes other than Lamination 1 Do not allow the machine to run with only one roll of film installed The melted resin will adhere to one roller and ruin future laminations 2 The width of film should be bigger than the material and Width of upper side and lower side of film should be same in order not to allow melted resin to adhere to the rollers 3 Be sure to adjust the film tension while in operation If the tension is too tight it could cause the film to stretch 4 After work you should clean the resin from the rollers before beginning the next operation 5 Please check the lubricant after long operation or you do not use for along time 6 Check the chain linking each gear is not loosened The limit tension allowed is 3mm 13 Symptom CHECK POINT Rollers do not operate Power cord may not be plugged 1 Check the power cord after press RUN button in Power switch is at OFF mode 2 Check if the switch is on Emergency switch may be at 3 Check if the emergency switch ON mode is off The safety cover is opened 4 Check the s w of safety cover is right Wrinkled lamination Film tension is not proper too 1 Adjust film tension result tight PART NAME MODEL PART NAME MODEL Core 6mm Bolt M8X
8. will come out from the rear site of machine 10 Check the status of lamination and place the pressure lever at lamination mode Methods of controlling pressure of the roller 1 For setting pull the pressure lever out and turn the lever to following the indication 2 OPEN 15mm Board For laminating 15mm thick board RSC 1650H 1650C 3 10 13mm Board For laminating 10 13mm thick board 4 5 mm Board For laminating 5 7mm thick board 5 1mm Hard Board For laminating 1mm thick board 6 Laminating For laminating 32 250micron thick film We designed this machine standing by user s convenience You can manipulate speed and temperature T rm RSC 1650C RSC 1650H 1 FUNCTIONS OF CONTROL PANEL 01019101019 RUN STOP BUTTON Run or stop the rollers SPEED BUTTON Increase or decrease speed LED OF SPEED Display or speed LED OF TEMP Display temperature TEMP BUTTON Increase or decrease temperature REVERSE BUTTON To make the rollers run backward 2 HOW TO USE BUTTONS Ss O i RUN STOP BUTTON Push the RUN button in order to run rollers and push mem button to stop it SPEED BUTTON Push the SPEED button to increase the speed push the speed button w to decrease the speed TEMP BUTTON Push the TEMP button to increase the temperature push the TEMP button to decrease REVERSE BUTTON Stay pressing REVERSE button to The roller
Download Pdf Manuals
Related Search