Rover 60 User's Manual
Contents
1. 3 3 To start the engine 1 Move the Throttle Control lever to the fast position Press the primer bulb firmly 5 times 3 Grasp the Operator presence control handle and hold against the handle bars Refer engine manufacturers instructions Fig 4 4 Grasp the starter handle and pull or turn the ignition key on Powerstart mowers 5 After engine starts move the Throttle Control to the slow position Page 1 ENGLISH 1 SETTING UP 3 Press firmly down on the catcher top to lock the barbs into slots Figure 1 4 Secure with two screws provided 2 BEFORE OPERATING CAUTION Avoid premature engine failure by using a clean funnel and clean away any possible contaminants 2 4 Fuel 1 Position the mower on a level surface in a well ventilated area and clean around the fuel tank cap 2 Using a clean funnel fill the fuel tank with unleaded petrol 3 Replace the fuel tank cap and clean away any spilt petrol 2 5 Controls Throttle Control Marked for O offi slow Operator Presense Control Handle moved towards the handle bars I Engine and blades are free to rotate Handle released 0 engine and blades stop rotating Figure 4 Self Propelled Drive Control Moved towards 1 on turns the clutch on and drives the mower forward Moved towards O off turns the clutch off and stops the mower driving Figure 5 Powerstart Turnthekey to on I position to engage the electric starter releasethe key when the engine s2. Spacer CE Rear extension Mod 60 Rover Mowers Limited A03802 A10016 A03581 A03557 A03560 A07679 A03741 A03565 A03559 A03558 A03556 A03563 A02083 A02012 A02223 A02002 A02163 A04060 Upper handle bars Mod 60 Throttle control assembly Throttle cable Quantum Key start housing Key start switch Ignition key Wiring loom Mod 60 CE Cable clamp Battery Battery block Battery support box Decal caution Setscrew 5 16 x 3 4 unc hex Washer 5 16 x 7 8 x 18g flat Nyloc nut 5 16 unc Speed nut 3 16 bsw Screw 3 16 x 1 2 mush head Rivet 73 AS 5 2 A03610 A10524 A10503 A02521 A03739 A03732 A03733 A02235 A04083 A03722 A03756 7 SPARE PARTS Foam block Bale assembly Mod 60 CE Handle assembly Mod 60 CE Spacer Handle grip CE Cable clip CE Rope stop CE Nyloc nut 1 4 unc Screw 10 x 3 4 pan head Brake cable mod 60 Switch Plate PAGE 9 Rover Mowers Limited Ae ll PAGE 10 GB Read the instructions carefully D Lesen sie die hinweise sorgfaltig F Lisenles instructions attentivement E a SP Lea las instrucciones con mucho cuidado NL Lees de gebruiksaanwijzing zorgruldig I Leggere attentamente le istruzioni GB Caution D Achtung Attention SP Atencion NL Voorzichtig I Attenzione GB IA E GB un rn 2 ie p NL GB SP NL GB Rotating cutting blades D Rotierende messer F Lames de coup rotatives SP Lame in m
3. attached to the positive terminal of the battery and the black lead to the negative terminal of the battery Fit the two rubber blocks to each end of the battery and place the battery complete with the rubber blocks into the battery support box with the battery terminals closest to the centre of the mower Refit the battery support box front cover and retain with the two screws 6 3 Battery charging A new battery when supplied with the mower may not be fully charged to maximum capacity The battery should have an initial charging period of 10 to 16 hours To charge the battery it must be removed from the mower first CAUTION Use only an approved battery charger supplied by the mower dealer which has been designed for use with this battery Connect the battery charger to the battery with the red lead positive to the positive terminal of the battery and the black negative lead to the negative terminal of the battery Page 3 5 MAINTENANCE Self propelled mowers Lubricate the slot at the centre of the drive pinion d Figure 15 Replace the wheel plug and wheel cap Replace the spark plug lead 5 7 Drive wheel cleaning 1 Remove the spark plug lead 2 Support the rear wheels off the ground and remove the wheel cap 3 Remove the ratchet plate c retaining the wheel to the axle Figure 15 4 Remove the wheel from the axle and clean the inside of the wheel hub 5 Replace the wheel and retain usin
4. el motor empieza a dejar a regresar al O posicion apagdo Regulatuur bij Powerstart machines Draai de startsleutel in postie no I em de electrische starter in te schaken Laat de startsleutel los als de motor loopt en laat hem in de O teruggaan Controlli messa in moto Girare la chiave posizione I per accendere il motorino elettrico d avviamento Lasciare libera la chiave quando il motore e in moto in modo che ritorni in posizione O Rover Mowers Limited O GB SP NL GB SP NL GB SP NL Self propelled drive control Moved towards I turns the clutch on and drives the mower forward Moved towards O turns the clutch off and stops the mower driving Selbetantriebbetatgung Einstellung auf I aktiviert die Kupplung und den Motor vorwars Einstellung auf I schaltet die kupplung aus und bringt den M her zum Stehen Contr le d autotraction D plac vers I enclenche l embrayage et fait avancer la tondeuse D plac vers O d cengage l embrayage el emp che la tondeuse d avancer Autopropulsado marcas del control Movido hacia I mueveel desembragador y pone a marcha el cortacesped Movido hacia el O apaga el desembragador y para el cortacesped Regulatuur bij relfverplaatsende machines Als men de knop op I zet is de koppeling ingeschakeld en de machine rijdt vooruit Als de knop O zet schakelt men de knoppeling uit en de machine stopt Camando trazione removente Se mosso
5. of the way Figure 12 5 Inspectthe drive chain and axle sprocket and replace if found to have excessive wear Replace the stone guard and drive shaft axle plate Replace the spark plug lead DUE 5 4 Clutch adjustment 1 Remove the spark plug lead Loosen the locknut a and turn the adjuster b clockwise until the clutch is felt to drag Figure 13 3 Back offthe adjuster anti clockwise 2 3 turns and retighten locknut a 4 Replace the spark plug lead Page 2 Rover Mowers Limited ENGLISH 5 5 Clutch lining inspection 5 6 1 Remove the spark plug lead Ze Remove the cover plate as explained in section 5 1 Drive chain lubrication 3 Check the thickness of the friction material Figure 13 If thickness of the friction material is less than 1mm the clutch plate should be replaced by an authorised Rover Mowers Limited Dealer 5 6 Drive pawl lubrication l Remove the spark plug lead Support the rear wheels off the ground Remove the rear drive wheel cap a and the wheel plug b Figure 14 Rotate the drive wheel to align the drive pinion with the wheel plug hole 6 1 Battery removal l Remove the two retaining screws from each side of the battery support box and remove the front cover Remove the battery from the support box and simultaneously disconnect the wiring loom from the battery terminals 6 2 Battery installation Je Connect the mower wiring loom to the battery with the red lead
6. verso I innestato innesta la frizione e muove in avanti la faiciatrice tosaerba Se mosso verso O disinnestato disinnesta la frizione e ferma la trazione della falciatrice tosaerba Operator presense control Handle moved towards the handle bars engine and blades are free to rotate Handle released engine and blades stop rotating Bedieneranwesenheitakontrolle Giff in Richtung Giffb gel vorgestzt motor und messer rotieren frei Griff gel st Motor und messer stoppen Contr le par op rateur Poig e avanc e vers les mancherons moteur et lames peuvent tourner Poign e rel ch e moteur arr tent de tourner Operador de las presencias controles Mango movido hacia manillas motor y cuchillas estanlibres de hacer vucltas Mango disparado motor y cuchillas paran de hacer vucltas Dodenmanskoop regulatuurknop die aangeeft dat de oparateur aanwezig is De gasbedieningshendel geplaast in de richting van de hand grepen de machine loopt en de messen draaien vrij Gasbedieningshendel is afgezet de machine stopt en de messen draaicn neit meer Comando presenza operatore D Manopola mossa verso barre manubrio motere e lame in posizione libers e rptanti O manopola disimpegnata Motre e lame fermi Throttle control Marked for off slow and fast positions Gasbedienung Markierung aus langsam sch schnell Contr le des gaz Marque pour les positions arr t ralenti acc l r et Control del accelerador Marcado por apagado despacio
7. 14 A03369 A03377 A03364 A03367 A03360 A10171 A03358 A10170 A03359 A03550 A03363 A03370 A04052 A03552 A03551 A03386 A02070 A03354 A03376 A03375 A03250 A02146 A02214 o 68 756528 5652 72 56 52 Wheel cap Drive shaft Rear drive chain Cable support bracket RH Chain tensioner Clutch engagement bush Driver clutch plate Clutch spring Driven clutch plate Clutch support shaft Drive chain housing LH Cable support bracket LH Drive pinion LH Self tapping screw 10 x 5 8 pan ph head Chain guard cover plate Drive chain housing RH Felt seal Roll pin 3 16 x 7 8 Sprocket PTO Front drive chain Pivot rod Handle Setscrew 1 4 x 3 4 unc hex Setscrew 1 4 x 5 8 unc hex A02078 A02081 A02235 82491162 A02001 A03092 A02030 A02209 A02044 8373109 A10146 82501108 A10284 A02118 A03336 83521047 A03470 290112 A03390 A03384 A10524 A10503 A03739 A02521 A03604 7 SPARE PARTS Setscrew 1 4 x 1 2 unc hex Setscrew 1 4 x 1 3 4 unc hex Nyloc nut 1 4 unc Nut 1 4 unc square pressed Nut 1 4 unc hex Washer Avdel 7301 0016 Washer 5 16 x 5 8 x 18g flat Washer 1 4 x 5 8 x 18g flat Washer 1 4 internal shakeproof Tension washer Wheel assembly Washer Avdel 7301 0008 Height adjustment lever assembly Rivet 3 4 x 1 4 flat head Plate Wheel plug Chain guide Rivet 73 AS 6 4 blind Clutch plate lining Tyre Bale assembly CE Handle assembly CE Handle grip CE
8. Description A03802 Handle bar A03317 Lower handle bar A03583 Throttle cable Mod 50 A03326 Throttle cable Mod 60 A10016 Throttle control assembly A02849 Lock handle A03307 Draw bolt A03500 Cable clip A03518 Plug spanner A10144 Grass catcher assembly A03324 Mesh A03447 Handle A02260 Roll pin 1 4 x 3 4 D JOU RW NM ra A02028 Setscrew 5 16 x 5 8 unc W Face Item Part No A04045 A02223 A10523 A10524 A10503 A03739 A02521 A03722 A03733 A02235 A04083 A03622 7 SPARE PARTS Description Flanged nut 5 16 unc Nyloc nut 5 16 unc Bale assembly CE Bale assembly CE Handle assembly CE Handle grip CE Spacer CE Brake cable mod 50 60 Rope stop CE Nyloc nut 1 4 unc Screw 10 x 19mm Pan Head PAGE 7 Rover Mowers Limited A02102 A10177 A03365 A07822 A03314 A03391 A03383 A10381 A03393 A02090 A03373 A03371 A03372 A03361 A07675 A10172 A03366 A03394 A02069 A03368 A03382 A03353 A03352 A03441 PAGE 8 Washer Avdel 7601 0010 Clutch lever Clutch cable Cable tie Rear axle support Stoneguard mount bracket Rear stoneguard 96012 Rear stoneguard 86012 66040 Drive shaft cover Circlip 1400 12 Pawl retainer washer Drive pinion RH Pawl Bearing 6001 DDU Nylon bush Rear axle assembly Rear chain guard Felt seal Roll pin 1 8 x 3 4 Rear drive shaft sprocket Dust seal Wheel bearing Geared wheel hub Washer plate A034
9. Owners Manual Gebrauchsanweisung Manuel du Propri taire Manual del Propietario Handleiding Manuale Instruzioni CP lt gt GE lt gt MODEL sO G0 Petrol Lawnmower Motor Rasenmiher Tondeuse a Gazon a Essence Cortadoras de Cesped a Gasolina Benzine Grasmaaimachine Falciatrice A Motore WW M TR PUE NID WANY Rover Mowers Limited ENGLISH PREFACE Thank you for buying a Rover Product All Rover Lawn mowers are designed and constructed to give optimum grass cutting performance under normal grass cutting conditions This manual covers the operation and maintenance of the Rover walk behind mower Please read and understand this owners manual before using the mower If any point is unclear contact Rover Mowers Limited or any authorised Rover Mower service dealer Rover Mowers Limited reserves the rightto make changes of and add improvements upon its product at anytime without notice or obligation The Company also reserves the right to discontinue manufacture of any product at its discretion at any time To emphasise special information the words WARNING and CAUTION are used WARNING CAUTION The safety of the user and others involved Personal Injury Follow these instructions to avoid mower damage and may result should this information be disregarded possible loss of warranty CONTENTS PAGE E a Da manon iii 6 Maintenance powerstart mowers 6 1 Battery removal ae 3 Safety Instructions eeeeaa
10. S 6 4 blind 10 A02127 Taptite 3 8 16 HWH x 1 Ind hex W H Duo 3 Decal Model 1 A04052 Self tapping screw 10 x 5 8 pan ph head2 A03549 Cable clip A03323 Plug chain slot model 50 A010141 Rear axle assembly model 50 A03313 Rear axle bush model 50 A03250 Plastic handle A10284 Height adj lever assembly A03336 Packing plate A03300 Base A03510 Height adjustment rack A03456 Rear Flap A03325 Spring rear flap A03455 Handle rear flap A03126 Pivot bush A10148 Conbar assembly A02591 Conbar spring A03515 Axle bracket RH A03514 Axle bracket LH A03516 Clamp bolt A02051 Woodruff key A01486 Disc boss A00293 Disc assembly A01716 Backplate A03830 Blade standard A03930 Blade Mulch N Catch A02066 Rivet m ra R R R BVB R bh bh FN R R R R M A00673 Blade bolt kit A10154 Disc bolt kit A10140 Front axle assembly professional A10527 Front axle assembly professional A03450 Front axle bush A03459 Wheel seal A03320 Front wheel assembly A03353 Wheel bearing A03414 Wheel cap A03306 Pivot rod A03743 Decal Warning A03319 Rear wheel assembly A03303 Grass deflector A10381 Rear stoneguard Mod 50 A03604 Rear stoneguard Mod 60 A02071 Rivet 73 SS 4 3 A02235 Nyloc nut 1 4 unc A03472 Decal turbothrust A03927 Nose comb A04108 Rivet A04099 Washer 3 16 x 3 4 A04111 Screw D D YN RR KN NR RK NN RR me MR M mere P D BD rR Fe ND PAGE 6 Rover Mowers Limited 7 2 Handle bar spare parts Item Part No
11. aaa aaa aaa iv 6 2 Battery instal 3 6 3 Battery charging ser 3 1 Setting Up o GA mae A 1 6 4 Care and handling wii GA 3 1 1 Grass catcher assembly 0 0 00 eeeeseeeeeneeeees 1 7 Spareparts EN EA OO AO 6 2 Before EIERE 1 7 1 Series 85000 86000 96000 base 6 2 1 Folding handles oisi rav AE l 7 2 Series 85000 86000 96000 bars 7 2 Handle bar height ee be tbe 1 Ho tole e E 8 2 3 Engine lubrication en 1 DE MM CO E 9 24 PE eO T l p Controls MEE l TEES TA TA PAGE NEU CURES 1 Figure 1 Grass catcher assembly s i 3 1 Grass catcher RERO 1 Figure 2 Handle bar height adiustment i 3 2 Adjusting the height of cut eee 1 Figure 3 Throttle control markings nee i 3 3 o start the engine ed oies 1 Figure 4 Operator presence control i 3 4 To stop the engine sseeeeeeeeeee 1 Figure 5 Self propelled drive control i 3 5 BEI propelled mowers ergeet 1 Figure 6 Grass catcher fitment 4m i 3 0 Blade brake control i e erprobt 1 Figure 7 Height adjustment az a WC i Figure 8 Blade bolt assembly sis ii 4 Maintenance General scsi 2 Figure 9 Drive chain cover plate 11 11 ii 4 1 BIneineoireleanet ieee rrr mentors 2 Figure 10 Drive chain ao de ii AD Snorkel air Cleaner 2 Figure 11 Drive shaft cover il 4 3 Spark RE 2 Figure 12 SONDE de ii 4 4 Cutting assemb
12. ake is on I Rover Mowers Limited 4 1 Engine air cleaner Refer to the engine manufacture s instructions for detailed cleaning instructions The engine air cleaner element must be serviced after each 25 hours of normal mowing The element must be serviced more regularly if the mower is used in dusty conditions 4 2 Snorkel air intake The snorkel air cleaner element must be serviced after each 50 hours of normal mowing The element must be serviced more regularly if the mower is used in dusty conditions Disconnect the air tube from the element holder Remove the holder cap Remove the cartridge and tap gently on a flat surface to remove dirt Replace element in holder and replace holder cap Replace the air tube to the bottom of the element holder ia ge pe NOTE Quantum engines fitted with a Remote snorkel air intake are not fitted with an air cleaner element Note the air cleaner element on this model is located on the engine CAUTION Do not allow dirt to enter the air tube engine damage may occur Check the condition of the air tube regularly and replace if damaged 4 3 Spark plug For best results remove and check the condition of the spark plug every 25 hours of use 1 Stop the engine and remove the spark plug lead 2 Clean dirt from around the spark plug and remove the spark plug 3 Ifa new spark plug is required use a Champion RJ19LM or equivalent and set the electrode gap at 0 7 to 0 8 mm 4 S
13. base of the handle bars on both sides of the mower using a 1 2 AF spanner Figure 2 2 Move the handle bars to the required position and tighten the handle bars nuts 2 3 Engine lubrication The engine oil level must be checked before attempting to start the engine Refer to the engine manufacturer s instructions 1 Position the mower on a level surface and clean around the dip stick or oil plug 2 Remove the dip stick or oil plug 3 Using a clean funnel slowly add oil in accordance with the engine manufacturer s instructions 4 Check the oil level by screwing in the dip stick or oil plug and removing again When oil level is correct replace the dip stick 3 1 Grass catcher Installing the grass catcher 1 Raise the rear flap of the mower Grasp the grass catcher by the top handle and position the grass catcher against the rear of the mower Figure 6 3 Lower the rear flap so that the back edge of the flap hooks over the grass catcher Removing the grass catcher Grasp the grass catcher top handle and lift up 2 Raise the rear flap of the mower to release grass catcher 3 Lift the grass catcher clear of the mower and lower the rear flap 3 2 Adjusting the height of cut 1 Grasp the height of cut lever A and apply an outward pressure to release the lever from the rack B Figure 7 2 Move the lever while holding out to the required height of cut position and engage the lever in the rack by releasing the lever
14. crew the spark plug into the engine and tighten to 20NM 5 1 Drive chain lubrication 1 Remove the spark plug lead Remove the cover plate screws a and lift off the cover plate b Figure 9 3 Support the rear wheels off the ground to enable the drive to be rotated 4 Use SAE 30 oil and lubricate the drive chains at point a whilst the chain is being rotated Figure 10 5 Replace the chain cover plate and secure 6 Replace the spark plug lead 5 2 Drive chain adjustment Front drive chain 1 Remove the spark plug lead 2 Remove the cover plate 3 Loosen the chain tensioner bolt b and move the chain tensioner to give a 3 mm deflection on the drive chain Figure 10 4 Tighten the chain tensioner bolt and rotate the drive wheels to check the drive chain for tight spots 5 Replace the cover plate Rear drive chain 1 Remove the spark plug lead 2 Loosen the rear drive chain tension nut c and slide it upwards to tighten the rear drive chain Figure 9 3 Retighten the rear drive chain tensioner nut and rotate the rear drive wheels to check for tight spots 4 Replace the spark plug lead ENGLISH 4 MAINTENANCE GENERAL CAUTION Do not over tighten the spark plug as engine damage may occur 4 4 Cutting assembly 1 Disconnect the spark plug lead 2 Move the height of cut lever to the high cut position and fold the handle bars 3 Tilt the mower so that the spark plug is up 4 Inspect the cu
15. d for transportation when crossing surfaces other than grass and when transporting the mower to and from the area to be mowed Never operate the mower with defective guards or shields or without safety devices for example deflectors and or grass catchers in place Do not change the engine governor settings or overspeed the engine m Disengage all blade and drive clutches before starting the engine Start the engine or switch on the mower carefully according to instructions and with feet well away from the blade s Do not tilt when starting the engine or switching on the motor unless the mower has to be tilted for starting In this case do not tilt it more than absolutely necessary and lift only the part which is away from the operator Do not start the engine when standing in front of the discharge chute Do not put hands or feet near or under rotating parts Keep clear of the discharge opening at all times Never pick up or carry a mower while the engine is running Stop the engine and disconnect the spark plug lead i Before clearing blockages or unclogging the chute ii Before checking cleaning or working on the mower ili After striking a foreign object Inspect the mower for damage and make repairs before restarting and operating the mower iv If the mower starts to vibrate abnormally check immediately Stop the engine i Whenever you leave the mower ii Before refuelling Reduce the throttle se
16. g a new ratchet plate 6 Replace the wheel plug and wheel cap 7 Replace the spark plug lead 6 MAINTENANCE Powerstart Mowers 2 Connect the battery charger to a suitable mains power outlet and switch on 3 Whenchargingis complete after 10to 16 hours switch off the power outlet and disconnect the battery charger from the power outlet 4 Disconnect the battery charger leads from the battery and refit the battery to the mower 6 4 Care and handling 1 Do not disassemble the battery as it s strong acid electrolyte may burn your skin or clothes 2 Donotshort out the battery terminals as this may burn the terminals and cause damage to the equipment 3 Do not incinerate the battery to depose of them The battery may explode if exposed to fire 4 Clean the battery with a dry cloth only never use oil petrol thinners or any other petrochemical 5 Handle the battery with care If the battery is dropped and the case is damaged the acid electrolyte sulphuric acid may leak out Wipe up leaking acid with a cloth and neutralise acid with an alkaline solution 6 In the event of electrolyte coming into contact with the skin immediately flush with water and seek medical attention Rover Mowers Limited 7 SPARE PARTS lf 26 7 1 Series 85000 86000 and 96000 base spare parts 27 A03492 Decal sound level A03409 Nameplate 373109 Tension washer A03092 Ratchet plate S2501116 Ratchet plate 290112 Poprivet 73 A
17. ly ssssseesseeee 2 Figure 13 Clutch adjustment ii 4 5 Blade CHAND ss hein 2 Figure 14 Drive wheel hs ii 4 6 Throttle control E 2 Figure 15 Drive pinion nn ii Figure 16 Powerstart control 3 ii 5 Maintenance self propelled mowers 2 5 1 Drive chain lubrication sssssss 2 5 2 Drive chain adIUS tent 2 5 3 Rear drive chain inspection 4 necis 3 5 4 Clutch adjustment ione 3 5 5 Clutch lining inspection 2 3 5 6 Drive pawl lubrication etras 3 5 7 Drive Wheel Cleaning z cda een 3 iii Rover Mowers Limited ENGLISH SAFETY INSTRUCTIONS Safety Instructions 1 Training Quo Read the instructions carefully Be familiar with the controls and the proper use of the equipment Never allow children or people unfamiliar with these instructions to use the mower Local regulations may restrict the age of the operator Never mow while people especially children or pets are nearby Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property Preparation While mowing always wear substantial footwear and long trousers Do not operate the equipment when barefoot or wearing open sandals Thoroughly inspect the area where the equipment is to be used and remove all stones sticks wires bones and other foreign objects WARNING Petrol is highly flammable Take the following precau
18. ovimento NL Draaiende Snijmessen I Lama con taglio a rotazione Keep bystanders away Andere fernhalten Restez a l ecart du public Mantenga alos espectadores le jos de ustad Houd toeschouwer op afstand Tenere lontano le persone circostanti Stop the engine and disconnect the spark plug lead before checking cleaning or working on the mower Den motor abstellen und das Zundkerzenkabel von der Zundkerze abziehen vor arbeiten am Maher Arretez le moteur et debranchez la bougie avant de verifer nettoyer ou reparer la tondeuse Pare el motor y desconecte el cable de la bujf a antes de comprobar limpiar o examinar la cortadora Stop de motor en trek de bougieleabel los voor het inspecteren schoonmaken of reparen van de maaimachine Fermare il motore e staccare il cavetto dalla candela prima di controllare pulire o aggiustare la tosaerba Powerstart Turn the key to the T position to engage the electric starter release the key when the engine starts and allow to return to O position Powerstart Kontrollen Zundschl ssel auf Stelle an I drehen um den Anlasser einzuschalten Beim Anspringen des Motors den Schl ck lassen Contr les de d marrage lectrique Tournez la cl sur la position T pour engager le d marrage lectrique Rel chez la cl quand le moteur d marre et laissez retourner la position O Powerstart Control Mover la llave hacia I las posicion para atracer el arranque electrico Dispara la llave cuando
19. rapido posiciones Gasknop regulatuur Voorzien van markteken uit langzaam snel tekening Comande Segno di poizione O staccato lento veloce PAGE 11 For your record Serial No F r Ihre Aufzeichnung H ndler Lieferdatum Modell Nr Seriennummer Pour votre information personnelle Fabricant Date d achat Mod le Para su referencia Vendedor Fecha de compra Modelo Serie n Voor uw informatie Dati da registrare Distributore Data d acquito Modello N de s rie N o Serie These machines are covered by one or more of the following Registered Designs and or Patents Registered Designs Australia 131504 134850 Patents Australia 713852 745750 New Zealand 330293 US 6085508 UK GR2325139 Mowers Limited ACN 000 257 303 em Head Office and Factory Rover Mowers Limited Endorsed 155 Fison Avenue West Eagle Farm 4009 Company 0 9001 Lie 10168 Brisbane Queensland Australia Slandards Australia Recycled paper e CC GWAIL 04003632 CE PRINTED IN AUSTRALIA Revision I O Copyright 1 2003
20. tarts and allow to return to the off 0 position Figure 16 Zi fast positions Figure 3 3 OPERATION CAUTION With powerstart mowers if the engine fails to start after 3 seconds of continuous cranking release the ignition key and wait 10 seconds before trying to restart the engine Ifthe engine still fails to start check the fuel level battery connections and battery condition If the engine is cranking slowly the battery may need charging refer to section 6 3 for battery charging 3 4 To stop the engine 1 Move the throttle control lever to the stop position O 2 Release the Operator presence control handle 3 Turn the fuel tap off where fitted 4 Remove the ignition key on Powerstart mowers 3 5 Drive engagement Self propelled mowers 1 Start the engine and set the engine speed to the required grass cutting speed 2 Push forward on the clutch engagement lever to engage the self propelled drive to the rear wheels Fig 5 3 To disengage the self propelled drive release the engagement lever and allow it to return to the disengaged position CAUTION Do not hold the engagement lever in a semi engaged position to slip the clutch as this will lead to excessive clutch wear 3 6 Blade Brake Control The mower engine is fitted with a blade brake system When the Operator Presence Control is held against the handle bars the brake is off 0 When the Operator presence control is released the blade br
21. tions i Store fuel in containers specially designed for this purpose ii Refuel outdoors only and do not smoke while refuelling iii Add fuel before starting the engine Never remove the cap of the fuel tank or add petrol while the engine is running or when the engine is hot iv If petrol is spilled do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until petrol vapours have dissipated v For reasons of safety the petrol tank and tank cap lock must be replaced if damaged Replace faulty silencers Before using always visually inspect to see that the blades blade bolts and cutter assembly are not worn or damaged Replace worn or damaged blades in sets to preserve balance On multibladed machines take care as rotating one blade can cause other blades to rotate Operation Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect Mow only in daylight or in good artificial light Avoid operating the equipment in wet grass where feasible Always be sure of your footing on slopes Walk never run For wheeled rotary machines mow across the face of slopes never up and down Exercise extreme caution when changing direction on slopes iv Do not mow excessively steep slopes Use extreme caution when reversing or pulling the mower towards you Stop the blade s if the mower has to be tilte
22. tting assembly for damage and wear 5 Check the disc retaining bolts Tighten the centre bolt to 48 Nm and the three concentric bolts to 14 Nm Return mower to its normal position and replace the spark plug lead WARNING Remove the spark plug lead before working on cutting assembly Do not work on the cutting assembly without wearing gloves 4 5 Blade change 1 Disconnect the spark plug lead 2 Set the mower to the high cut position 3 Lift the rear flap on rear catcher mowers and prop open the flap to give access to the blades Tilt utility mowers so that the spark plug is up 4 Remove the blade blade retaining bolts nuts and washers and discard Retain only the D plates 5 Fit new blades blade bolts washers and nuts in sets to maintain balance Figure 8 6 Tighten the blade nuts to 16 NM Check the blades are free to move when the blade nut is tensioned 7 Remove the flap prop or lower the mower to the ground and replace the spark plug lead 4 6 Throttle control Each 25 hours of mowing use a small amount of light oil to lubricate the throttle control lever 5 MAINTENANCE Self propelled mowers 5 3 Rear drive chain inspection 1 Remove the spark plug lead Remove the drive shaft cover plate retaining screws a and remove cover plate b Figure 11 3 Remove the stone guard retaining screws c and remove the stone guard Figure 11 4 Remove the chain guard nuts d and slide the chain guard out
23. tting during engine run out and if the engine is provided with a shut off valve turn off the fuel at the conclusion of mowing Maintenance and storage Keep all nuts bolts and screws tight to be sure the equipment is in safe working condition Never store the equipment with petrol in the tank inside a building where fumes may reach an open flame or spark Allow the engine to cool before storing in any enclosure To reduce the fire hazard keep the engine silencer battery compartment and petrol storage area free of grass leaves or excessive grease Check the grass catcher frequently for wear or deterioration Replace worn or damaged parts for safety If the fuel tank has to be drained do this outdoors Rover Mowers Limited 1 1 Grass catcher assembly 1 Locate the catcher handle and align its front lugs with the slots in the top of the catcher and press firmly into position Figure 1 2 Position the catcher top over the catcher bottom aligning the barbs on the top with the slots in the bottom Figure 1 2 1 Folding handles l Locking knobs By turning these knobs the handle bars can be either locked in the operating position or folded for storage 2 Locking lever Lift the lever to release the handle bars for folding or push the lever closed to lock handle bars in the operating position Adjust the tension by turning the lock nut with a 1 2 AF spanner 2 2 Handle bar height 1 Loosen the two nuts A at the
Download Pdf Manuals
Related Search