ResMed Ventilation Hood vpap-st User's Manual
Contents
1. Connect one end of the air tubing firmly onto the air outlet Connect the assembled mask system to the free end of the air tubing Notes e Always ensure that the VPAP SFA is placed in an area where the alarm LED indicators are clearly visible e For more information on assembling your mask see your mask user guide Recommended masks are available on www resmed com on the Products page under Service amp Support aRWN gt VPAP ST A basics Key The control panel of your device includes an LCD screen as well as Home Al a Start Stop button Push dial Alarm mute button Info and Setup o menu keys Humidity Level rey Ramp Lal nomen Heated Tube E Allows you to view your sleep statistics or exit Climate Control from the menu LCD screen Start Stop Displays the menus treatment Push dial screens and reminders Start Stop button Alarm mute Starts or stops treatment Setup menu Info menu mm g e o E Alarm mute Press once to mute alarms Press a second time to se unmute Setup menu Alarm and thera Allows you to make changes to settings Yellow flashes during an larm or exit from the menu Blue on during therapy if e Push dial Turning the dial allows you to scroll through the menu and change settings Pushing the dial allows you to enter into a menu and confirm your choice 3 English Adjusting ramp time Designed to make the beginning of treatment more comfortable2. ramp time is the period during which the pressure increases from a low start pressure to the treatment pressure To adjust your ramp time RAMP LE al CL ZX RAMP A RAMP 1 From your HOME 2 Press 3 Turn untilthe 4 Press to screen turn amp The selection is ramp time you confirm your choice until the RAMP highlighted in require is displayed screen is displayed orange in blue Using Mask Fit You can use Mask Fit to help you fit your mask properly This feature delivers CPAP pressure for a three minute period prior to starting treatment during which you can check and adjust your Mask Fit to minimize leaks 1 Fit your mask as described in the mask user guide 2 From your HOME screen push and hold for three seconds One of the following MASK FIT screens is displayed MASK FIT MASK FIT Adjust 3 If necessary adjust your mask mask cushion and headgear until Mask Fit indicates Good After three minutes the pressure reverts to the set pressure and treatment will begin You can end Mask Fit at any time by pressing Selecting the mask type To select your type of mask gt SETTINGS a Tube Standard Mask Pillows Jane per Tube Standard Mask Pillows f Mask Fit gt fr SETTINGS Tube Standard Mask Fit gt Mask Fit gt lt HOME lt lt HOME lt lt HOME 1 Press The SETTINGS 2 Turn until Mask is 3 Press The selection is screen
3. ie SLEEP REPORT ae SERVICE AC UEG 8 2 ns AE lt In the Sleep Quality screen you In the Sleep Report only the In the Service information the can always view your usage period can be changed other total device run hours includes warm up cool down times for the humidifier and the software identifications are displayed hours during the last session values are for display only and if enabled by your clinician data on Mask Fit and AHI is displayed To return to the HOME screen push i Viewing alarms The VPAP STA is fitted with an alarm module that continuously monitors both therapy and device conditions Alarms are only activated when therapy Is running An alarm condition is indicated by an audible sound a flashing yellow alarm LED and a message on the screen When the device is turned on the yellow alarm LED will flash and the alarm will sound to confirm that the alarm is working A CLIMATE CTRL Alam High leak please icheck system setup v Alarm activated v Alarm cleared Multiple alarms When an alarm activates a To clear an alarm message To view the list of alarm corresponding alarm message is press amp This allows you messages go to the Treatment displayed If multiple alarms are to return to the previously screen and press until active the latest alarm message displayed screen If the alarm Treatment screen 3 is displayed is displayed and as these are condition remains the alarm will cl
4. Med Corp 9001 Spectrum Center Boulevard San Diego CA 92123 USA ResMed UK Ltd 96 Milton Park Abingdon Oxfordshire 0X14 4RY UK See www resmed com for other ResMed locations worldwide For patent information see www resmed com ip S9 H5i ClimateLine SlimLine SmartStart and VPAP are trademarks of ResMed Ltd and S9 ClimateLine SlimLine SmartStart and VPAP are registered in U S Patent and Trademark Office 2012 ResMed Ltd C 0123 Global leaders in sleep and respiratory medicine www resmed com
5. VPAP ST A NONINVASIVE VENTILATOR Welcome Guide English Making quality of care easy __ Respiratory Care Solutions Making quality of care easy Welcome Thank you for choosing the VPAP ST A Before operating the device please read the entire Welcome and Information Guides DC power inlet Module Adapter port Air filter Air outlet SD card slot VPAP ST A at a glance The VPAP ST A system comprises the following elements e VPAP ST A device Air tubing 90W power supply unit S9 Travel bag SD card S9 SD card protective folder Optional components include e H5i heated humidifier Standard air tubing SlimLine air tubing 3 m air tubing ClimateLine heated air tubing ClimateLine heated air tubing SOW power supply unit does not support H5i e Power Station I battery pack DC DC Converter 24V 90W Travelling tips When travelling with your VPAP ST A only e Ensure you pack the SlimLine or Standard air tubing as the ClimateLine or ClimateLine heated air tubing is not designed to connect directly to the device e Ensure you purchase and travel with the approved power cord for the region where you will be using the device English WHYTTett EEN gn WE Si ane aL Setting up Connect the DC plug of the power supply unit to the rear of the device Connect the power cord to the power supply unit Plug the other end of the power cord into the power outlet
6. eared each message can be re OCCuTr read Note Power Fail and Alarm Fail alarms are cleared by pressing O Muting the alarm To mute an alarm for two minutes press oO once If the condition remains the alarm will sound again after two minutes To turn on the alarm again press a second time The alarm LED will remain lit for as long as the condition remains 9 English Cleaning and maintenance You should regularly carry out cleaning and maintenance as described in this section Refer to your mask and humidifier user guides for detailed instructions regarding the care of these devices Daily Remove the air tubing by pulling on the finger grips on the cuff Hang it in a clean dry place until next use Notes e Do not hang the air tubing in direct sunlight as it may harden over time and eventually crack e Do not wash the air tubing in a washing machine or dishwasher Weekly 1 Remove the air tubing from the device and the mask 2 Wash the air tubing in warm water using mild detergent 3 Rinse thoroughly hang and allow to dry 4 Before next use reconnect the air tubing to the air outlet and mask Monthly 1 Wipe the exterior of the device with a damp cloth and mild detergent 2 Check the air filter for holes and blockage by dirt or dust Replace the air filter if necessary Replacing the air filter Replace the air filter every six months or more often if necessary 1 Remove the air filter cover from t
7. example screens shown in ST mode once therapy has started A HUMIDITY LEVEL eaten faz A a v H5i humidifier ST v H5i humidifier v H5i humidifier v ClimateLine or ClimateLineMX v ClimateLine or ClimateLine v Climate Control Auto v Climate Control Manual TREATMENT 1 3 SpO2 98 Pulse v Therapy data without v Oximetry data via the optional accessories oximeter adapter Pressure bar In bilevel modes the fixed vertical lines on the pressure bar indicate the expiratory and inspiratory pressures While the treatment is ramping indicated by an orange ramp icon or variable the pressure values appear in orange When a set pressure is reached these values are displayed in white In CPAP mode only a set pressure is shown 7 English To toggle between the treatment screens press from your HOME screen TREATMENT 2 3 W TREATMENT 2 3 WS TREATMENT 3 3 Ti 1 7 Ti Max 2 0 A Ti 1 7 Ti Max 2 0 A I E 1 2 0 Ti Min 0 5 IE 1 2 0 Ti Min 0 5 Spont Spont Tr IC 95 E Spont Spont 6 0 ST 12 0 v Treatment with device v Treatment with spontaneous v Treatment with alarm trigger Timed and cycle trigger and cycled breaths functionality Timed Ti Max or Ti Min breath indicators Viewing the Info menu The Info menu has a series of screens showing your sleep quality sleep report and service information To view the Info menu push i from your HOME screen ie SLEEP QUALITY
8. he back of the device 2 Remove and discard the old air filter 3 Insert anew ResMed air filter ensuring that it is sitting flat in the air filter cover 4 Replace the air filter cover Air filter cover Notes e Ensure the air filter and air filter cover are fitted at all umes e Do not wash the air filter The air filter is not washable or reusable Air filter SD card An SD card has been supplied to gather therapy data from your device and provide settings updates from your clinician When instructed to do so disconnect the device from the power outlet remove your SD card insert it in the protective folder and send it to your clinician Removing the card 1 Push in the SD card to release it 2 Remove the card 3 Insert the card into the protective folder 4 Send the protective folder back to your clinician as instructed For more information on removing and inserting your card refer to your S9 SD Card Protective Folder provided with your device Please retain the S9 SD Card Protective Folder for future use Notes e For Troubleshooting information refer to the Information Guide e For more product information see www resmed com 11 English _ Respiratory Care Solutions Making quality of care easy 368811 1 2012 05 VPAP ST A WELCOME EUR1 w taal Manufacturer ResMed Ltd 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia Distributed by Res
9. is displayed displayed in blue highlighted in orange SETTINGS SETTINGS k Tube Standard sa Tube Standard Face Mask Full Face f Mask Fit gt Mask Fit gt g HOME lt lt HOME G 4 Turn until the mask 5 ress to confirm your 6 Push to return to the setting that you require is choice HOME screen displayed S9 Essentials S9 Essentials is designed to make device interaction and menu navigation easier for you If enabled by the clinician S9 Essentials disables the Info and Setup functionality so that you can simply start and stop therapy and adjust ramp humidification and Climate Control 5 English Getting started Make sure the power is connected Adjust the ramp time or humidification level if required Fit your mask as described in your mask user guide To start therapy simply breathe into the mask and or press Lie down and arrange the air tubing so that it is free to move If you turn in your sleep T k and To stop treatment at any time remove your mask and or press OQ Notes e f your clinician has enabled SmartStart your device will start automatically when you breathe into the mask and stop automatically when you remove your mask e f power is interrupted during treatment the device automatically restarts therapy when power is restored Viewing the treatment screens Depending on how the system has been configured you will see one of the following
Download Pdf Manuals
Related Search