Renesas H8/38347 User's Manual
Contents
1. Everywhere you imagine E lt E NI ESAS WiULGIA DLE L Renesas Starter Kit for H8 38347 LCD Module Application interfaces E8 connector for E8a LCD connector Reset E8a debugger module Ie p TU E E ee p ee Ge ee OO ii FReta n et i i Analog adjust User switches 1 Installation Do not connect the E8a module until the software support has been installed 1 Insert the CD into your computer s CD ROM drive The CD should automatically run the installation program If the installer does not start browse to the RSK directory from the CD root folder and double click on setup exe 2 The installer will ask you which language is to be used please choose the appropriate one 3 On the first screen of the installer proper click lt Next gt 4 The License Agreement will be shown click lt Yes gt 5 The next screen asks you to pick the world region please select and click lt Next gt 6 Select the RSK you wish to install and click lt Next gt 7 The destination folders are specified on the next screens Itis recommended to accept the default settings Click lt Next gt to continue 8 Click lt Next gt on all screens until the Installation process commences 9 After the installation the machine s site code will be shown this is not important at this stage click lt Next gt then lt Finish gt 10 Auto update dialog box will be launched Configure the Auto Update settings dialog2. n list on the toolbar is selected Click the lt Connect gt button on the debug toolbar Xs Select the correct device type e g H8 38347F for PaM RSKH838347 Select Erase Flash and Connect Select Power target from Emulator and select 5V if the E8 is to provide the power to the RSK board Otherwise aE Hszas347F S I o Yi connect a 5V center positive supply Click lt OK gt oeg Erase Flash and Connect Emulator mode C keep Flash and Connect C Program Flash The first time the E8a is used P the E8AH8 dialog appears click lt OK gt and select Renesas Communications and click lt Close gt I Power Target from Emulator MAR 30 m A Do not show this dialog box again Otherwise skip to the next step Accept any dialog warning that an older version of E8a firmware is necessary to work with the application Allow download of firmware to complete this may take several seconds System Clock Fist select the clock speed 16 00MHz for the Please input System Clack RSKH838347 then click lt OK gt Cancel MHz Second select the ID Code OE8A for the Cancel RSKH838347 then click lt OK gt The flash memory write program and E8a monitor are then downloaded to the microcontroller Right click on the download module listed in Download me i J l the left hand pane and select Download 523 Depen Download The code will be do
3. ormance Embedded Workshop gt High performance Embedded Workshop 19 In the Welcome dialog box Verify Create New Workspace is selected Click lt OK gt 20 In the New Project Workspace dialog box Set the CPU Family to H8S H8 300 and verify the Tool chain is set to Hitachi H8S H8 300 Standard Select E8A_RSKH838347 from the left hand pane 21 Enter a name for the workspace The project name will be automatically completed with the Workspace name You can change this name to Tutorial if required Click lt OK gt 22 On the E8A_RSKH838347 Step 1 window Select Tutorial and click lt Next gt 23 On the E8A_RSKH838347 Step 2 window Click lt Finish gt 24 On the Project Generator Information window Click lt OK gt The project that is created has two configurations The Release configuration can be used for the final release code version The Debug configuration allows modifications to the configuration for debugging 25 Select the Debug build configuration in the left hand drop Deu E DefautSession E down list on the toolbar 26 Click on the Build icon to compile assemble and link the project D006364_11_S01_V04 27 28 29 30 31 32 33 34 35 36 37 38 39 Programming and Debug Ensure the SessionH8_SLP_E8a SYSTEM 300L Debug B SessionH _SLP_E8a SYS session in the right hand drop dow
4. renesas com Japan csc renesas com Note on Autoupdate The Autoupdater is configured to automatically add itself to the Startup folder in the Windows Start Menu and use the registry defaults for access to the web After restarting the machine the Icon will appear in the System Tray next to the clock To change the settings or access Autoupdate simply right click on the icon and use the menu that appears Renesas Solutions Corporation 2007 Renesas Technology Corporation 2007 Renesas Technology Europe Limited 2007 D006364_11_S01_V04
5. to allow your installation to be checked for required updates D006364_11_S01_V04 Connection 11 Fit the LCD module to J10 on the RSK so it lies above J3 Ensure all the pins of the connector are correctly inserted in the socket 12 Now connect the E8a to J6 E8 on the RSK using the ribbon cable also connect the LCD module to J10 on the RSK ensuring that the pin 1 designation corresponds to the marking on the RSK 13 Connect the E8a debugger to a spare USB port The Found New Hardware Wizard will appear Please follow the steps below to install the drivers Note that administrator privileges are required for a Windows 2000 XP machine Do not use Windows update to find the drivers 14 Verify the Recommended option is selected and click lt Next gt 15 If using Windows XP skip to step 17 otherwise click lt Next gt 16 Click lt Next gt to install the driver 17 Click lt Finish gt to close the wizard Note The Windows driver signing dialog may be displayed Please accept the driver to continue 3 HEW Workspace HEW integrates various tools such as compiler assembler debugger and editor into a common graphical user interface To learn more on how to user HEW open the HEW manual installed on your computer Start Menu gt All Programs gt Renesas gt High performance Embedded Workshop gt Manual Navigator 18 Launch HEW from the Start Menu Start Menu gt All Programs gt Renesas gt High perf
6. wnloaded to the E Fle Download Debug Data Only microcontroller This may take several E W Unload p maa seconds Int B lec Download A New Module me ell Click the lt Reset Go gt button The code will run and you will see the LEDs flash on the board Click the lt Stop gt button w The code will stop and the source code will be opened at the current program counter D006364_11_S01_V04 5 Next Step After you have completed this quick start procedure please review the tutorial code and sample code that came with the kit You can add projects to the current workspace by selecting Project gt Insert Project from the main menu The tutorials will help you understand the device and development process using Renesas Development Tools The Hardware manual supplied with this RSK is current at the time of publication Please check for any updates to the device manual from the Renesas website at www renesas com renesas starter kits 6 Renesas H8 Compiler The version of the compiler provided with this RSK is fully functional but time limited You have 60 days to evaluate the full product before the compiler will limit the code linker to 64k bytes Full licensed H8 compiler versions are available from your Renesas supplier 7 Support Online technical support and information is available at www renesas com renesas starter kits Technical Contact Details America techsupport rta renesas com Europe tools support eu
Download Pdf Manuals
Related Search