Remington MS2-150 User's Manual
Contents
1. 27714_MS2_150_IB 9 1 05 act Page 1 REMINGTON MICROSCREEN 100 27714_MS2_150_IB 9 1 05 10 50 AM Page 2 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be observed induding the following Read all instructions before using this appliance DANGER To reduce the risk of electric shock El Do not reach for an appliance that has fallen into water Unplug it immediately E Dona place or store this appliance where it can fall or be pulled into a tub or sink while it is plugged in El Except when charging always unplug this appliance from the electrical outlet immediately after using E Unplug this appliance before deaning it E Do not use an extension cord or a voltage converter with this appliance El Do no use while bathing or in a shower WARNING To reduce the risk of bums fire electric shock or injury to persons M This appliance is for household use only E An appliance should never be left unattended when it s plugged in except when charging a recharge able appliance E dose supervision is necessary when this appliance is used by on or near children or invalids E Use this appliance only for its intended use as is described in this manual Do not use attach ments not recommended by manufacturer E Keep the cord away from heated surfaces E Never operate this appliance if it has a darraged cord or plug if it is not working pr2. and trimmer Lse the cleaning brush to sweep any loose hairs from the cutters and trintrers 5 After deaning retum the foils and head assembly to their original position on the shaver 6 To dean the extemal surfaces of the shaver use a damp cloth Do NOT use strong detergents or other chemicals 7 To dry wipe the surface of the overall shaver with a dry towel Do NOT use a hairdryer or heater to dry the shaver Screens and Gutters To assure smocth efficient performance it is important to dean your shaver Daily Blow out the stubble after each shave L Tun the shaver off 2 Remove the head assembly by squeezing on both releese buttons and pulling up from the body of the shaver 3 Thoroughly blow out the stubble fromthe screen and cutters 4 Replace head asserbly Vibeldy Brush out the cutters and trintrer at least once a week 1 Tun the shaver off 2 Remove the head assembly by squeezing on bath release buttons and pulling up from the body of the shaver 3 Use the deaning brush to sweep out the cutters and tinne DONOT USE THE CLEANING BRUSH ONTHE SCREENS Damage may occur to the holes in the screens 4 Replace head assembly Remington Shaver Saver Lubricant SP 4 lubricates and deans your shaver s cutters and head assembly The lubricant helps remove hair dippings while reducing weer A quick spray after each shave keeps your shaver operat ing at peak performance Cleaning Caut
3. WARRANTIES CF ATNESS AND MERCHANTABILITY ARE LIMITED IN DURATION TO TWO YEARS FROM DATE OF ORIGINAL PURCHASE This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province Sorre states do not allow the exdusion or limitation of incidental special or consequential damages Spectrum Brands Inc Money back Offer If within 30 days after you have purchased your Remington branded product you are not satisfied and would like a refund retum it with the sales slip indicating purchase price and date of purchase to the retailer from whom it was purchased Spectrum Brands Inc will reimburse all retailers who accept the product within 30 days from the date of purchase If you have any questions conceming the money back guarantee please call 800 736 4648 in the US or 800 268 0425 in Canada 105 130 Vac 60 Hz 105 240 Vac 50 Hz Questions or comments Call 800 736 4648 in the US or 800 268 0425 in Canada or visit wwwrenington prodiucts com Dist by Spectrum Brands Inc Madison W 53711 Dist by Rayovac Canada Inc Mississauga ON LAW 2T7 REMINGTON MICROSCREEN and SHAVER SAVER are trademarks of ROVCAL INC 2005 ROVCAL INC T22 17350 07 05 J ob CS27714 a Q Uy En 27714_MS2_150_IB 9 1 05 mg Page 12 aa
4. cant looks like fine white or gray powder and disappears with use Before you begin E vit at least 15 minutes after getting up before shaving to ensure the face is free of puffiness that may be present from sleeping E Make sure your face is dean and dry before starting E Always use a dean dry shaver To To shme Push the ON CFF button Hold the shaver so both foils touch your face at the same time This allows the shaver to work the way it was designed for the dosest shave and ninimum wear Awoid holding the shaver at an angle so only one screen touches the skin at a time This will distort the screen and could cause skin irritation Shave with short Circular strokes Use your free hand to stretch your skin This encourages your Whiskers to stand out making it easier for them to enter the cutting chamber Never press hard Pressing only flattens your whiskers making it harder for them to enter the cutting chamber It will also wear out the cutting surface more quickly 27714_MS2_150_IB 9 1 05 10 50 AM Page 8 Cleaning Your Shaver Remington recommends cleaning your shaver after every use for optimal performance L Tum shaver OFF 2 Press side release button to flip open head asserrbly 3 Screens Do not use the brush to clean the screens Instead blow the shavings out or rinse the screens under cold or warm water 4 Gutters
5. h downward on the ends of the cutters as you may bend the cutter reducing its ability to operate smoothly 4 Do not remove cutters from the plastic pieces they are attached to as you may darrage the assembly When is it time to replace your screens and cutters Because they are subject to daily use the cutters and screens of your shaver will wear and eventually require replacement to maintain a dose confortable shave It is very important to replace your screens and cutters when necessary to ensure a dose comfortable shave without irritation Depending on your shaving technique and habits the screens will usually last 6 months the cutters 12 months If you are replacing the cutters it s a good idea to replace the screens at the sarre tine Here are sorre signs that your foils and cutters need replacing Invitation As screens get wom you may notice that your skin feels more sensitive after a shave particularly when you apply aftershave Pulling As cutters wear your shave may not feel as dose and you may feel your shaver is pulling at your whiskers We ar through You may notice that the Cutters have wom through the screens The replacement for this shaver is model SP 67 Screens and SP 69 Screens and cutters US residents To order shaver accessories call 800 736 4648 visit Wu remington products com or visit your local retailer Canadian residents To order shaver accesso
6. ions E The corstuction of this shaver is for dry Operation only It is not waterproof Never put the shaiver in part or completely into wetter E Do nd use an aggressive deansing agent as this may destroy the shaver coatings E Do nt remove or replace the head asem bly while shaver is running as it nay cause damage to the unit s screens or cutters E Replace wom or damaged parts with Remington replacerrert parts only Tinmer Care Cleaning L Tum the shaver off 2 Extend the trintrer to its maximum height by pressing the right tiinnmer button 3 Use the cleaning brush to sweep off any dippings that may have accumulated around the trimmer assembly Using the supplied brush will enable you to get into the area between the trinmer and the shaver Lubricating L Every six months apply a drop of light machine oil one third and two thirds of the way along the blade 2 Using your fingertip spread the oil along the teeth 3 Run the tinme for a few seconds to distribute oil Replacing Cutters and Screens To prevent inadvertent damage to the cut ters and screens do not attempt to remove them from the head assembly unless you are replacing them Removal instructions are induded with the cutter and screen replacement packages To replace a cutter assembly that is 1L Hold the asserrbly in the middle of the e 2 Genty slide the plastic portion of the cutter assembly over the top of the oscillator tip 3 Do not pus
7. operly if it has been dropped or damaged or if it has been dropped into water If any of these things happen retum the appliance to an authorized service center for exarrination and repair Never drop or insert any object into any of the appliance s openings Do not use outdoors or operate where aerosol Spray products are being used or where oxygen is being administered Always store this appliance and cord in a moisture free area Do nat store it in temperatures exceeding 140 F 600 Do not plug or unplug this appli ance when your hands are wet Do not wrap the cord around the appliance Always attach the plug to the appliance then to the outlet To disconnect tum all controls to OFF then remove plug from outlet Detach removeable power cords from appliances for storage Do not use this appliance with a damaged or broken screen or cutters as injury may occur SAVE THESE INSTRUCTIONS eee Ic 27714_MS2_150_IB 9 1 05 10 50 AM Page 4 E Product Features IMICROSCREEN 100 Congratulations on your purchase of a premium Rerrington shaver The MicroScreen 100 has Revolutionary Shaving Technology Which model is yours A Screen amp cutter assembly B 3 position timmer C Head release button one on each side D Tinner extension button E OVWCFF button B H Rechargeable si can only be Your shaver can be used almost anywhe
8. re F Charging indicator without the cord in the world because it has automatic dual G Recharge port voltage conversion providing AC current H Charging adapter Indicator Lights between 105 130 Vac 60 Hz and 105 240 1 Head guard Vec 50 Hz J ust plug it in to the local outlet Charging 3 i and t 0 Cleaning brush he ing indi Sa light that you may need an adapter plug use i K Storage pouch a E as usual glows when the shaver is charging or fully charged 27714_MS2_150_IB 9 1 05 10 50 AM Page 6 How to Use Charging Before using your shaver for the first time put it on charge for 24 hours NOTE It may take up to 3 cycles for the battery to reach full capacity To charge your shaver H Slide the power button downward to the CFF position EI Connect the supplied AC power cord to the shaver s recharge port and then to an electical outlet HB Your shaver cannot be overcharged so you can leave it plugged in and charging between shaves E To presene the life of the batteries allow them to fully discharge every six months then recharge them for 24 hours Removing the Headiguarcd Before operating your shaver remove the headguard which protects the screen and cutter assembly It is important to remove the headguard correctly to avoid damaging the dips that hold it to the shaver L Press lightly on the top of the headguard 2 Lift the lower rear edge 3 Pull the headguard away from the shaver l Away
9. ries please call 800 268 0425 visit www renington products com or visit your local retailer 27714_MS2_150_IB 9 1 05 10 50 AM Page 10 Disposal Battery Removel When your rechargeable shaver reaches the end of its useful life the batteries must be removed fromthe shaver and be recycled or disposed of properly in accordance with your state and local requirements If this is not required by law you may elect to dispose of the shaver without removing the batteries CAUTION DO NOT PUT IN FIRE OR MUTILATE YOUR BATTERIES WHEN DISPOSING AS THEY MAY BURST CR RELEASE TOXIC MATERIALS DO NOT SHORT CIRCUIT AS IT MAY CAUSE BURNS DISPOSE PROPERLY IN ACCORDANCE WITH YOUR LOCAL AND STATE REQUIREMENTS l To awida possible electric shock hazard unplug cord if used from electric outlet and shaver 1L Remove head assembly by first pressing the two side buttons 2 Un diip the top metal u bracket by prying the lower back edge over the snap Lift the lip of the rubber boot off the housing 3 Pry off the front panel 4 Remove the two screws securing the cord opening 5 Squeeze the front housing and pull the back off to expose the PC board and batteries 6 Pry the PC board assembly out of the shaver housing 7 Cut or break the wire straps on both ends of the batteries pry the batteries fromthe foam adhesive tape on the PCB Only follow these instruction
10. s keep the protective head guard on the shaver head and keep the timmer in the OFF position when the shaver is not in use Operating the Trimmer Your shaver is equipped with a 3 position tinner L Completely retracted down the rinmer is out of the way and off for when you wart to use the screens alone Press the trintrer button down with your thumb to get it into this position 2 In the midde position the tintrer works with the screens so the screens can get in extra dose cutting the longer hard to shave hairs Push the LEFT side of trintrer button for this position 3 Fully extended up the tinner can be used to trim your sidebums and mustache Push the RIGHT side of trintrer button for this position How it works Trimrer blades work in concert with the shavers dual screen system cutting the longer difficult to shave hairs The timmer blades take the brunt of the shaver wear and tear so you get a dose confortable shave time after time Adjusting to your new shaver As with every shaver your shave will improve over time So allow about three weeks to develop an effective shaving style and for your beard to adjust to the new shaver The adaptation period nay take a little longer if your skin is sensitive or if you altemate between shaving methods To help smooth the transition to your new shaver Remington has applied a special lubricant to the shaver s screens and cutters The lubri
11. s when you are ready to dispose your shaver as your shaver will no longer be operable Performance Guarantee Full Two Year Viarranty Spectrum Brands Inc warrants this product against any defects that are due to faulty material or workmanship for a two year peri od from the original date of consumer pur chase This warranty does not indude dam age to the product resulting from accident or misuse If the product should become defective with in the warranty period we will repair it or elect to replace it free of charge Retum your product and sales receipt with your name address and day time phone number to Spectrum Brands Inc Attention Consumer Services 601 Rayovac Drive Madison W 53711 For more inforrration call 800 736 4648 in the US or 800 268 0425 in Canada Warranty excludes H Screens and cutters KEEP CRIGINAL SALES RECHIPT AS PROOF OF PURCHASE FOR WARRANTY PURPOSES This warranty does not cover products damaged by the following Accident nisuse abuse or alteration of the product Servicing by unauthorized persons Use with unauthorized accessories Connecting it to incorrect current and voltage Wrapping cord around appliance causing premature wear amp breakage Any other conditions beyond our control SPECTRUM BRANDS INT SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE CF THS PROD UCT ALL IMPLIED VWARRANMIES INCLUDING BUT NOT LIMITED TOIMPLIED
Download Pdf Manuals
Related Search