Quantum Travan 20 ATAPI Poster
Contents
1. you can purchase a Y shaped power cable from your computer dealer Step 6 Complete the installation a Check all cables including those of adjacent devices to make sure that none have loosened during the installation Make sure that all cables are routed so that they will not bind or become crimped when you replace the cover of your computer b Reinstall your computer cover c Doa test backup to make sure that your tape drive and software are working properly Primary IDE port gv STEP 4 oe SSN Secondary 7 IDE port k i BZzz Zz F STEP 5 2003 Certance LLC All rights reserved Part number 10010845 001 Certance the Certance logo and TapeStor are registered trademarks of Certance LLC Other product names are registered trademarks or trademarks of their owners Certance reserves the right to change without notice product offerings or specifications No part of this publication may be reproduced in any form without written permission from Certance LLC2. 3 5 inch drive bay skip to step 3b below If you are mounting the drive in a 5 25 inch drive bay attach mounting brackets to each side of the drive as shown at far left b Slide the drive into an unused drive bay until the bezel is flush with the front of the computer Secure the drive using four mounting screws Do not overtighten the screws BQ LQ Step 4 Connect the IDE cable SS SS 5 25 Sl sch SS Attach your tape drive to the secondary IDE port eS ES Note Do not attach your tape drive to any cable that is already connected to a hard drive a floppy drive or a sound card If no drives or cables are attached to your secondary IDE port you may need to purchase a new 40 pin IDE cable to run from the secondary IDE port to your tape drive Attach the new IDE cable to the secondary port and to the tape drive as shown in the illustration 4a If you already have a CD ROM or other device attached to your secondary IDE port attach the tape drive to the middle connector on the IDE cable as shown in illustration 4b Note When attaching cables Make sure that pin 1 on the drive is connected with pin 1 on the IDE connector Pin 1 on the tape drive is located next to the 4 pin power cable Pin 1 on the IDE cable is indicated by a stripe on the edge of the cable Step 5 Connect the power cable Connect a 4 pin power cable to the back of the tape drive If all the power cables in your computer are being used by other devices
3. To install your new TapeStor Travan 20GB tape drive follow the simple steps listed below For detailed installation instructions and trouble shooting tips see the online manual on the Tape Resource CD TAPESTOR Before installing the drive check to make sure your TapeStor 20GB box contains the following items ar EASY INSTALLATION SHEET RE C internal ATAPI Tape Drive 20 Gbyte capacity e Mounting brackets to adapt the drive to a 5 25 inch drive bay e Mounting screws e CD with Yosemite TapeWare backup software ATAP 2 ile B TAP f D R l VE A Certance Tape Resource CD contains the Online Installation Manual and much more e This Easy Installation Sheet Items you may need for installation You will need flat bladed and Phillips screwdrivers to complete the installation In addition To protect your computer and drive from static electricity install the drive in an If your computer has only a single IDE port you will need to purchase and install an ATAPI host adapter to uncarpeted area and ground yourself frequently on a grounded metal object such provide a secondary IDE port for the tape drive as the frame of your computer before opening the antistatic bag or touching any If no drives are presently attached to your secondary IDE port you will probably need to purchase a 40 pin IDE components within your computer interface cable for your tape drive e Turn off your computer and any peripheral devices be
4. fore installing the drive Step 1 Install the bac kup software We recommend that you install your backup software before you install the tape drive For more information see the instructions that came with the backup software Note For detailed tape drive installation instructions operating instructions and troubleshooting tips see the online TapeStor 20GB manual on the Certance Tape Resource CD The CD will startup automatically on most Windows systems if it doesn t autostart run setup bat from the CD From the introductory screen click on Installing Your Drive Linux users can find the manual in the pdfs directory of the CD under the appropriate language Note Drive is shown upside down Before continuing to the next step shut down your computer turn off the power and remove the cover Step 2 Configure the drive optional If your tape drive will be on the same cable with an existing ATAPI device such as a CD ROM you do not have to change the default jumper setting tape drive is a slave Make sure that the existing ATAPI device is the Master iy Master Aih Slave default i Cable select STEP 2 If your tape drive will be the only device on your secondary IDE port you need to configure your tape drive as a Master Turn the drive over and move the master slave jumper to the Master position as shown at left Step 3 Mount the drive a If you are mounting the tape drive in a
Download Pdf Manuals
Related Search