PYLE Audio PICDLD82I User's Manual
Contents
1. PLEASE USE ONLY THE SUPPLIED AC ADAPTOR TO OPERATE THE UNIT USE OF OTHER ADAPTORS MAY DAMAGE THE UNIT OR CAUSE IT TO MALFUNCTION PLUG THE TAIL END OF THE AC ADAPTOR INTO THE DC JACK SOCKET ON THE UNDERNEATH OF THE MAIN UNIT MAKE SURE THE VOLTAGE OF THE AC ADAPTOR OPERATES AT THE SAME VOLTAGE AS YOUR LOCAL HOUSEHOLD VOLTAGE INSERT THE PLUG AT THE END OF THE POWER CORD INTO THE WALL AC SOCKET PRESS THE ON STANDBY KEY TO SWITCH ON THE UNIT THIS UNIT IS DESIGNED TO OPERATE WITHOUT EVER BEING TOTALLY POWERED OFF IT WILL EITHER BE ON OR IN STANDBY MODE ANYTIME DURING STANDBY MODE YOU CAN SWITCH ON THE UNIT BY PRESSING THE ON STANDBY KEY SAVE ENERGY BY SWITCHING THE SYSTEM TO STANDBY MODE BACK UP BATTERIES OPEN THE BATTERY DOOR AT THE BOTTOM OF UNIT INSERT 1 PC CR 2032 LITHIUM CELL BATTERY IN THE BATTERY COMPARTMENT THIS BATTERY IS FOR BACKUP OF THE REAL TIME CLOCK AND RADIO MEMORY PRESET STATIONS DURING BRIEF POWER OUTAGES PLEASE OBSERVE THE CORRECT POLARITIES OR THE MEMORY WILL NOT BE PROPERLY MAINTAINED PREPARATION OF REMOTE CONTROL REMOVE GENTLY PULL OUT THE PLASTIC TAB FROM THE BATTERY COMPARTMENT AT THE REAR OF THE REMOTE CONTROL TEST THE REMOTE CONTROL BY PRESSING THE W ON STANDBY KEY TO CHECK THAT THE UNIT SWITCHES ON PROPERLY USING THE REMOTE CONTROL E 6 DIGITAL CLOCK FUNCTION HOW TO SET CORRECT TIME THIS UNIT HAS A BUILT IN DIGI2. NOKIA b 6210 6650 8910i 9300 Il DC JACK 2 THIS JACK IS DESIGNATED FOR USE WITH THE SUPPLIED UNIVERSAL ADAPTER WIRE IN COMBINATION WITH ONE OF THE SUPPLIED CONNECTORS TO CHARGE ONE OF SEVERAL MOBILE PHONES LIFT THE UNIT TRAY CONNECT THE TAIL END OF UNIVERSAL ADAPTER WIRE INTO THE DC JACK 2 AND CONNECT ONE OF THE SUPPLIED ADAPTER CONNECTORS TO THE UNIVERSAL ADAPTER WIRE FEMALE SOCKET INSERT THE ADAPTER CONNECTOR TO THE RESPECTIVE MOBILE PHONE S ADAPTER SOCKET WHICH NEEDS TO BE CHARGED THE UNIT SHALL THEN AUTOMATICALLY BEGIN CHARGING THE RESPECTIVE MOBILE PHONE NOTE AT ANY GIVEN TIME ONLY ONE OF THE DC JACKS CAN BE USED WIRE CONNECTOR DEVICES CONNECTOR Male3 5x1 1mm pae Female3 5x1 1mm Male3 5x1 1mm MINI USB MOST BLACKBERRY amp HTC UNITS 1 com cil MICRO USB SELECT BLACKBERRY amp OTHER UNITS MOTOROLA lll SAMSUNG c SONY ERICSSON ud CHARGING 3 USB JACK IN THE EVENT THAT THE SUPPLIED WIRES AND CONNECTORS ARE UNABLE TO CHARGE YOUR MOBILE PHONE THIS UNIT IS EQUIPPED WITH A USB CHARGING ONLY JACK TO CHARGE MOBILE PHONES THAT ARE SUPPLIED WITH USB CABLES THE USB JACK ALLOWS FOR NOT ONLY CHARGING OF MOBILE PHONES BUT ALSO HUNDREDS OF OTHER DEVICES COVERING BLUETOOTH HEADSETS PORT
3. 0V 50 60Hz SPEAKER MAIN SPEAKER 2 x 2 FREQUENCY FM 87 5 108 MHz THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS SHOULD BE PLACED ON THE APPARATUS THE MARKING AND RATING LABEL IS LOCATED AT REAR BOTTOM ENCLOSURE OF THE APPARATUS THE MAINS PLUG IS USED AS THE DISCONNECT DEVICE AND IT SHALL REMAIN READILY OPERABLE TO BE COMPLETELY DISCONNECTED THE POWER INPUT THE MAINS PLUG OF THE APPARATUS SHALL BE DISCONNECTED FROM THE MAINS COMPLETELY THE MAINS PLUG SHOULD NOT BE OBSTRUCTED OR SHOULD BE EASILY ACCESSED DURING INTENDED USE UNDER THE INFLUENCE OF ELECTROSTATIC PHENOMENON THE PRODUCT MAY MALFUNCTION AND USER TO POWER RESET EXCESSIVE SOUND PRESSURE FROM EARPHONES AND HEADPHONES CAN CAUSE HEARING LOSS BATTERY SHOULD NOT BE EXPOSED TO EXCESSIVE HEAT SUCH AS SUNSHINE FIRE OR THE LIKE ELECTROSTATIC DISCHARGE ESD PRECAUTION WHEN ELECTROSTATIC DISCHARGE ESD OCCURS AT THE FRONT SURFACE WHETHER METAL OR PLASTIC OR NEAR ANY PART OR ANY BUTTON OF THIS UNIT OR AT THE USB PORT AND OR SD CARD SLOTS IF THEY EXIST ON THIS PRODUCT THERE MAY BE A POSSIBILITY THAT THE PRODUCT MAY STOP OPERATION AND OR SHUT DOWN IMMEDIATELY THIS IS A NORMAL CONDITION AND INTENDED TO PROTECT THE UNIT AND INTERNAL COMPONENTS AGAINST DAMAGE IN SUCH A CASE PLEASE RESET THE UNIT BY DISCONNECTING AND RECONNECTING AC POWER SOURCE TO REVERT THE UNIT TO NORMAL OPERATION CAUTIO
4. ABLE GAME CONSOLES AND MANY MORE TO USE THE USB JACK CHARGING CAPABILITY LIFT THE UNIT TRAY CONNECT THE TAIL END OF THE USB WIRE SUPPLIED WITH YOUR MOBILE PHONE OR THIRD PARTY DEVICE INTO THE DC JACK AND CONNECT THE DEVICE ADAPTER END ON THE USB WIRE INTO THE RESPECTIVE SOCKET ON THE DEVICE IN NEED OF CHARGING THE UNIT SHALL THEN AUTOMATICALLY BEGIN CHARGING THE RESPECTIVE DEVICE CONNECTOR COMPATIBILITY THIS UNIT COMES WITH 5 CONNECTOR ADAPTERS TO COVER CHARGING OF MOST POPULAR MOBILE PHONE MODELS AND BRANDS DETAILS AS ABOVE DRAWING E 13 USING THE AUDIO LINE IN CONNECTION AUX INPUT YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A MP3 PLAYER TO THIS UNIT TO LISTEN TO THE SOUND OF THAT DEVICE THROUGH THE HIGH QUALITY AMPLIFIER OF THIS MUSIC SYSTEM TO CONNECT THE EXTERNAL DEVICE PLEASE USE A STANDARD STEREO HEADPHONE 3 5MM TO 3 5MM PLUGS CABLE TO CONNECT THE HEADPHONE OUT OR AUDIO LINE OUT OF THE DEVICE TO THE AUX INPUT SOCKET OF THIS UNIT SWITCH THE FUNCTION TO AUX USING THE KEY ON UNIT OR AUX KEY ON REMOTE CONTROL SWITCH ON THE UNIT AND THE EXTERNAL DEVICE eg MP3 PLAYER START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME CONTROL OF THE MAIN UNIT TO THE DESIRED LEVEL REMEMBER TO SWITCH OFF THE UNIT WHEN YOU ARE FINISHED USING THE EXTERNAL DEVICE SPECIFICATIONS POWER SUPPLY DC 6V 3A THOUGH BUILT IN DC JACK EXTERNAL AC DC POWER ADAPTOR 110V 24
5. ACK OF UNIT AT ANYTIME DURING PLAYBACK PRESS AND RELEASE THE gt t NEXT TUNE OR 144 BACK TUNE KEYS TO SKIP FORWARD OR BACKWARDS BY ONE TRACK AS DESIRED ANY ANYTIME DURING PLAYBACK PRESS AND HOLD THE NEXT TUNE OR I44 BACK TUNE KEYS TO FAST FORWARD CUE OR FAST REVERSE REVIEW THE SPECIFIC TRACK WHICH IS CURRENTLY PLAYING YOU CAN OPERATE THE iPod iPhone USING EITHER THE SET REMOTE CONTROL OR DIRECTLY WITH THE iPod iPhone ITSELF WHEN THE iPod iPhone HAS BEEN CONNECTED WITH THE UNIT IT WILL START CHARGING THE BATTERY OF THE iPod iPhone NEVER REMOVE OR UNPLUG THE iPod iPhone FROM THE SET DURING PLAYBACK ALWAYS PRESS amp HOLD FOR 2 SECONDS THE PLAY PAUSE KEY FIRST AND THEN PRESS THE KEY TO SWITCH TO ANOTHER SOURCE EG RADIO OR AUX BEFORE REMOVING OR UNPLUGGING THE iPod iPhone TO PREVENT DAMAGE TO YOUR SONG FILES OR MEMORY DEVICES Made for iPod Made for iPhone mean that an electronic accessory has been designed to connect specifically to iPod iPhone respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod iPhone may affect wireless performance REPEAT PLAYBACK FUNCTION iPod iPhone AT ANYTIME DURING iPod iPhone PLAYBACK PRESS THE FOLLO
6. CHARGE UNIT NEC SECTION 810 20 GROUNDING CONDUCTORS ELECTRIC SERVICE NEC SECTION 810 21 EQUIPMENT GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC NATIONAL ELECTRICAL CODE NEC ART 250 PART H LIGHTNING For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal OVERLOADING Do not overload wall outlets extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock OBJECT AND LIQUID ENTRY Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service per
7. HE KEY ONCE TO SWITCH ON THE UNIT PRESS THE KEY REPEATEDLY UNTIL THE DISPLAY SHOWS FM SYMBOL TO IMPROVE FM RADIO RECEPTION FULLY EXTEND THE FM ANTENNA WIRE AND ADJUST IT S POSITION ANYTIME IN FM STATIONS USE THE KEY TO SELECT THE DESIRED MODE FM MONO STEREO IN SOME CASES WHERE RECEPTION IS POOR IT MAY BE ADVISABLE TO SELECT MONO MODE TO IMPROVE CLARITY OF THE RADIO SIGNAL MANUAL FREQUENCY ADJUSTMENT SCAN MODE PRESS AND IMMEDIATELY RELEASE THE gt t NEXT TUNE kea TUNE KEY TO SCAN MANUALLY ADJUST THE RADIO FREQUENCY UP OR DOWN BY 1 STEP ATA TIME THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH STEP S POSITION WHEN A DESIRED FREQUENCY OR STATION IS REACHED IT CAN BE SAVED INTO ONE OF THE MEMORY POSITIONS SEE RADIO MEMORY SECTION AUTOMATIC FREQUENCY ADJUSTMENT SEEK MODE PRESS AND HOLD FOR 2 SECONDS THE gt NEXT TUNE OR kea BACK TUNE KEYS TO SEEK AUTOMATICALLY ADJUST THE RADIO FREQUENCY UP OR DOWN TO THE NEXT AVAILABLE RADIO STATION THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY OF THE NEXT STATION THAT IS FOUND WHEN A DESIRED STATION IS REACHED IT CAN BE SAVED INTO ONE OF THE MEMORY POSITIONS SEE RADIO MEMORY SECTION RADIO MEMORY STATION PRESET MEMORY STORAGE AT ANY TIME THE CURRENTLY DISPLAYED STATION OR FREQUENCY CAN BE STORED INTO ONE OF THE MEMORY POSITION PRESS AND
8. HOLD MEMORY RECALL KEY PRESS gt NEXT TUNE OR kea TUNE KEY TO SELECT DESIRED MEMORY POSITION THERE ARE 30 MEMORY POSITIONS PRESS MEMORY RECALL KEY ONCE TO SAVE THE SELECTED STATION INTO THE SELECTED MEMORY POSITION RADIO MEMORY RECALL PRESET MEMORY STATION RECALL ANY SAVED MEMORY SIMPLY SHORT PRESS MEMORY RECALL KEY PRESS 1 NEXT TUNE OR kea TUNE TO SELECT DESIRED MEMORY POSITION TO CLEAR THE MEMORY OF ANY POSITION SIMPLY SAVE A NEW STATION TO THE SAME MEMORY POSITIONS OPERATION WITH THE iPod iPhone THIS UNIT IS DESIGNED TO ALLOW YOU TO CONNECT AN iPod iPhone WITHOUT THE NEED FOR DOCK CONNECTORS THE DESIGN OF THE UNIT HAS BEEN STRUCTURED TO PROVIDE SUPPORT TO TE CONNECTOR UNDER NORMAL USAGE WITHOUT EXCESSIVE eN ON THE iPod iPhone WHEN CONTROLLING PLAYBACK USING THE iPod iPhone TURN ON BOTH THE UNIT AND THE iPod iPhone PRESS THE FUNCTION KEY REPEATEDLY UNTIL THE DISPLAY SHOWS iPod THE UNIT WILL AUTOMATICALLY START PLAYBACK OF THE SONGS THE iPod iPhone DISPLAY WILL INDICATE THE INFORMATION OF THE CURRENT SONG TRACK AT ANYTIME DURING PLAYBACK PRESS THE PLAY PAUSE KEY TO PAUSE OPERATION OF THE UNIT PRESS PLAY PAUSE KEY TO RESUME OPERATION AT THE SAME TRACK amp POSITION AT ANYTIME DURING PLAYBACK PRESS amp HOLD THE KEY TO STOP PLAYB
9. KEY TO ACCESS THE SLEEP TIME THEN PRESS THE KEY REPEATEDLY TO CHOOSE THE AUTOMATIC OFF TIME THE SE SYMBOL WILL BE SHOW ON THE DISPLAY Lus T Pus T ins T Pins T Pus PE wins PE wins PE wins PE ws PE 00 00 MEANS SLEEP TIMER IS DEACTIVATED ELECTRONIC VOLUME CONTROL THIS UNIT USES AN ELECTRONIC VOLUME CONTROL PUSH BUTTON TYPE TO INCREASE OR DECREASE THE LOUDNESS OF UNIT PRESS THE VOLUME UP OR VOLUME DOWN KEYS RESPECTIVELY RELEASE THE KEY WHEN VOLUME LEVEL IS AT THE DESIRED LOUDNESS SOMETIMES ESPECIALLY DURING LISTENING TO THE RADIO YOU MAY NOTICE A CLICK CLICK CLICK REPEATING SOUND WHEN YOU ARE INCREASING OR DECREASING THE VOLUME THIS IS ANORMAL CONDITION amp THE SOUND WILL DISAPPEAR WHEN YOU RELEASE THE VOLUME KEY WHEN YOU REACH THE DESIRED VOLUME LEVEL MUSIC EQUALIZER AT ANY TIME DURING PLAYBACK PRESS SLEEP KEY REPEATEDLY TO CHOOSE THE DESIRED SOUND EFFECT ACCORDING TO THE MUSIC YOU ARE LISTENING TO i E 0 EQOFF gt E2 classic Es Bass 4 E4 sazz 4 DIMMER FUNCTION THIS SET HAS A DIMMER FUNCTION TO ADJUST THE BRIGHTNESS LEVEL OF THE DISPLAY SIMPLY ADJUST IT AS DESIRED BY PRESSING THE DIMMER KEY REPEATEDLY HIGH NORMAL OFF BRIGHTNESS 100 50 0 TO REDUCE EYE STRAIN AND TO SAVE ENERGY THE DISPLAY WILL ALWAYS RETURN IN NORMAL DIMMER AFTER RESET THE UNIT E 9 OPERATION OF RADIO PRESS T
10. L SYMBOL STOP FLASHING TO INDICATE ALARM OFF THE SET WILL RETURN TO STANDBY MODE AFTER ABOUT 5 SECONDS THE AL SYMBOL WILL DISAPPEAR FROM THE DISPLAY ALARM MODE SETTING 1 FOR iPod iPhone CONNECT THE iPod iPhone AS DESCRIBED SELECT amp PAUSE PLAYBACK OF THE SONG OR DESIRED PLAYLIST TO PLAY AT THE WAKE UP TIME PLAYBACK WILL AUTOMATICALLY RESUME AT ALARM TIME 2 FOR RADIO TUNE IN THE DESIRED STATION PRIOR TO PLAYING THE UNIT ON STANDBY MODE 3 THE WAKE UP VOLUME LEVEL AUTOMATICALLY WILL RISE FROM LEVEL 0 16 MINIMUM FOR WAKE UP VOLUME LEVEL MORE THAN 16 IT MUST BE SET BY THE USER 4 IF THE ALARM IS SET AS WAKE TO iPod YOU WILL NEED TO CONNECT THE iPod PROPERLY AS DESCRIBED OTHERWISE THE BUZZER ALARM WILL SOUND AT THE SET TIME IF THE iPod HAS NOT BE CONNECTED 5 THE ALARM WAKE UP TIMER WILL AUTOMATICALLY TURN OFF AFTER AROUND AN HOUR SNOOZE FUNCTION WHENEVER THE ALARM COMES ON IT CAN BE TEMPORARILY SUSPENDED FORA SHORT PERIOD OF APPROXIMATELY 9MINUTES BY TOUCHING THE SNOOZE PLATE ONCE THE ALARM WILL THEN AUTOMATICALLY COME ON AGAIN AFTER APPROXIMATELY 9 MINUTES SNOOZE PERIOD HAS ENDED THE PROCEDURE CAN BE REPEATED FOR APPROXIMATELY AN HOUR AUTOMATIC POWER OFF SLEEP FUNCTION THIS SET HAS A SPECIAL SLEEP TIMER FUNCTION WHICH CAN AUTOMATICALLY SWITCH OFF THE UNIT THIS IS USEFUL FOR SLEEPING TO MUSIC AT NIGHT AT ANY TIME WHILE THE UNIT IS OPERATING PRESS AND HOLD THE SLEEP
11. N DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE E 14
12. OPERATING INSTRUCTIONS PYLE www PyleAudio com PICDLD82I PLL BLUE CLOCK OH OBRA een iPod iTouch iPhone Multi Source Charging CLOCK RADIO Made for iPod LliPhone RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash WARNING To reduce The exclamation and arrowhead the risk of electric shock do point within the within the triangle not remove cover or back triangle is a warning is a user serviceable sign alerting you of sign alerting you of parts inside Refer important instructions dangerous voltage servicing to qualified accompanying the inside the product Service personnel product WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS NOTE CAUTION SYMBOLS ARE PRINTED ON BOTTOM OF UNIT PLEASE REFER TO INSTRUCTION MANUAL PLEASE NOTE YOU WILL FIND THE CAUTION RATING LABEL FOR THIS PRODUCT DO NOT EXPOSE TO DRIPPING LOCATED ON THE REAR OF THE UNIT OR SPLASHING LIQUIDS CAUTION GROUNDING OR POLARIZATION THE PRECAUTIONS SHOULD BE TAKEN SO THAT THE WIDER BLADE OF THE AC PLUG MUST MATCH THE SLOT IN RECEPTACLE WALL SOCKET E 2 pum Om P 10 11 12 13 14 15 IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS All the safety and operating instruction should be read before the product is operated RETAIN IN
13. STRUCTIONS The safety and operating instruction should be retained for future reference HEED WARNINGS All warning on the product and in the operating instructions should be adhered to FOLLOW INSTRUCTIONS All operating and use instructions should be followed CLEANING Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a dry cloth for cleaning ATTACHMENTS Do not use attachments not recommended by the product manufacturer as they may cause hazards WATER AND MOISTURE Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like ACCESSORIES Do not place this product on an unstable cart stand tripod bracket or table The product may fall causing serious injury to a child or adult and serious damage to the product Use only with a cart stand tripod bracket or table recommended by the manufacturer or sold with the product Any mounting of the product should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer A product and cart combination should be moved with care Quick stops excessive force and uneven surfaces may causethe appliance and cart e combination to overturn g VENTILATION Slots and openings in the cabinet are provided for ventilation VN L2 and to ensure reliable operation of the product and to prot
14. TAL CLOCK WHICH IS DISPLAYED AT ALL TIMES DURING THE UNIT BEING POWERED OTHER THAN DURING THE FOLLOWING THREE SITUATIONS 1 WHEN THE DIMMER FUNCTION IS ENABLED TO HAVE DISPLAY BRIGHTNESS LEVEL AT 0 DISPLAY LIGHTS OFF FULL DIMMED 2 WHEN USING THE FUNCTION KEY TO SELECT THE RADIO FM MODE THE DISPLAY WILL MOMENTARILY SHOW THE FM FREQUENCY PAY BACK BEFORE RETURNING TO THE DIGITAL CLOCK 3 WHEN USING THE NIT FUNCTIONS CONTROLS I E VOLUME CONTROL FM FREQUENCY TUNING ALARM SETTING ETC THAT REQUIRE INFORMATION TO BE MOMENTARILY DISPLAYED TO SET THE TIME FOLLOW THE BELOW STEPS SWITCH UNIT TO STAND BY MODE PRESS amp HOLD CLOCK ADJ FOR 3 SECONDS DISPLAY SHOWS 7i HOUR OR i HOUR FLASHING PRESS gt NEXT TUNE OR BACK TUNE TO SELECT 12 HOUR OR 24 HOUR CLOCK DISPLAY SYSTEM amp PRESS CLOCK ADJ TO CONFIRM YOUR SELECTION PRESS gt gt NEXT TUNE OR kea BACK TUNE REPEATEDLY TO SET THE CORRECT HOUR IN THE DISPLAY amp PRESS CLOCK ADJ TO CONFIRM PRESS gt t NEXT TUNE OR kea BACK TUNE REPEATEDLY TO SET THE CORRECT MINUTE IN THE DISPLAY amp PRESS CLOCK ADJ TO CONFIRM CORRECT TIME IS NOW SET amp WILL BE SHOWN IN THE DISPLAY THAT WHEN THE DIGITAL CLOCK IS NOT SET THE DIGITAL CLOCK DISPLAY SHALL CONTINUOUSLY FLASH TO INDICATE THAT THE CORRECT TIME HAS NOT YET BEEN SET ALARM FUNC
15. TION THIS SET IS EQUIPPED WITH 3 ALARM MODES BUZZER RADIO AND iPod BEFORE SETTING THE ALARM MAKE SURE TO SET THE CLOCK ALARM TIME SETTING 1 AT STANDBY MODE PRESS AND HOLD KEY UNTIL THE DISPLAY HOUR FLASHING 2 PRESS gt gt NEXT TUNE OR a BACK TUNE KEY TO REACH THE HOUR OF THE DESIRED WAKE UP TIME 3 PRESS ALARM SET TO CONFIRM THE UNIT SHOULD NOW HAVE THE DISPLAY MINUTES FLASHING 4 PRESS gt gt I NEXT TUNE OR H BACK TUNE KEY TO REACH THE MINUTES OF THE DESIRED WAKE UP TIME 5 PRESS ALARM SET KEY TO COMPLETE AND CONFIRM THE ALARM TIME SETTING ALARM ON SETTING ONCE THE ALARM TIME IS SET SELECT THE SOURCE THAT YOU WISH THE UNIT TO PLAYBACK FROM AT WAKE UP TIME AL BUZZER ALARM FM RADIO iPod iPod or iPhone 1 AT STANDBY MODE PRESS ALARM SET KEY ONCE THE DISPLAY WILL CHANGE FROM REAL TIME TO ALARM WAKE UP TIME THAT WAS SET 2 PRESS ALARM SET KEY REPEATEDLY TO SELECT THE SOURCE AS DESIRED THE SELECTED SOURCE WILL BE INDICATED BY THE SYMBOL FLASHING AFTER SELECTING THE SOURCE THE SET WILL RETURN TO STANDBY MODE AFTER ABOUT 5 SECONDS THE AL SYMBOL WILL BE SHOWN ON THE DISPLAY AS LONG AS THE ALARM FUNCTION IS ACTIVE ALARM OFF SETTING 1 AT STANDBY MODE PRESS ALARM SET ONCE THE DISPLAY WILL CHANGE FROM REAL TIME TO ALARM WAKE UP TIME THAT WAS SET 2 ORESSIALARM REPEATEDLY TO SELECT THE AL SYMBOL UNTIL THE A
16. WING SYMBOLS ON THE iPod iPhone SCREEN 922 C gt TO REPEAT ALL TRACKS SHUFFLE RANDOM PLAYBACK FUNCTION iPod THIS UNIT IS ABLE TO SHUFFLE ALL SONGS ON AN iPod iPhone AND PLAY THEM BACK IN RANDOM ORDER TO ACTIVATE THIS FUNCTION SELECT THE SHUFFLE ICON DQ ON THE iPod iPhone THE SHUFFLE SYMBOL WILL BE DISPLAYED ON THE iPod iPhone SCREEN amp THE SONGS WILL BE PLAYED IN RANDOM ORDER E 11 MULTI CHARGING FUNCTION THIS UNIT IS DESIGNED TO ALLOW YOU TO CONVENIENTLY AND IN A SIMPLE MANNER CHARGE UPTO 3 DEVICES WITHOUT THE CLUTTER OF MULTIPLE ADAPTERS RUNNING TOAWALL OR EXTENSION POWER OUTLET CHARGING 1 DOCK SIMPLY DOCK THE IPOD IPHONE FOR PLAYBACK OR CHARGING AND THE UNIT SHALL AUTOMATICALLY BEGIN CHARGING THE iPod iPhone CHARGING 2 DC JACKS I DC JACK 1 THIS JACK IS DESIGNATED WITH A SPECIAL VOLTAGE REQUIRED TO CHARGE NOKIA PHONES THE SUPPLIED NOKIA a amp NOKIA b WIRES COVER CHARGING FOR MOST OF THE AVAILABLE NOKIA PHONES LIFT THE UNIT TRAY CONNECT THE TAIL END OF NOKIA a OR NOKIA b WIRE INTO THE UNITS DC JACK 1 AND CONNECT THE OTHER ADAPTER END OF THE RESPECTIVE WIRE INTO YOUR NOKIA ADAPTER SOCKET THE UNIT SHALL THEN AUTOMATICALLY BEGIN CHARGING THE NOKIA PHONE DEVICES CONNECTOR Male3 5x1 35 Maley tommy Male2 1x0 6mm NOKIA E90 N70 N80 N96 Male3 5x1 1mm m
17. ecommended by the manufacturer HEAT The product should be situated away from heat sources such as radiators heat registers stoves or other products including amplifiers that produce heat LI e LOCATION OF CONTROLS UNIT TRAY ON STANDBY KEY EQ SLEEP KEY DIMMER KEY FUNCTION KEY DIGITAL DISPLAY CAVITY FOR DOCK ADAPTOR VOLUME UP DOWN KEY CLOCK ADJ DISPLAY KEY 10 TOUCH SNOOZE PLATE 11 BACK TUNE KEY 12 PLAY PAUSE FM MODE KEY 13 NEXT TUNE KEY 14 MEMORY RECALL KEY 15 ALARM SET OFF KEY 16 SPEAKERS LEFT amp RIGHT 17 USB JACK 18 DC JACK SELECTOR 19A DC JACK 1 19B DC JACK 2 20 BACK UP BATTERY COMPARTMENT 21 AUX INPUT SOCKET 22 DC JACK DC 6V zzz G 23 FM ANTENNA WIRE E 5 REMOTE CONTROL ON STANDBY KEY SLEEP EQ KEY FUNCTION KEY BACK TUNE DOWN KEY PLAY PAUSE FM MODE KEY NEXT TUNE UP KEY DISPLAY CLOCK SET KEY MEM RECALL KEY VOLUME KEY 10 DIMMER KEY 11 ALARM ON OFF SET KEY 12 VOLUME KEY 13 BATTERY COMPARTMENT 1 2 3 4 5 6 7 8 9 POWER SUPPLY AC OPERATION EXTERNAL AC DC POWER ADAPTOR THIS SET IS EQUIPPED WITH A DC JACK CAPABLE OF ACCEPTING AC ADAPTORS WITH A RATING OF DC 6V 3A AND WITH A PLUG WITH THE FOLLOWING POLARITIES AS SHOWN CENTER POSITIVE
18. ect it from overheating and these openings must not be blocked or covered The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instruction have been adhered to POWER SOURCES This product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company For products intended to operate from battery power or other sources refer to the operating instruction GROUNDING OR POLARIZATION This product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarizes plug ALTERNATE WARNINGS This product is equipped with a three wire grounding type plug a plug having a third grounding pin This plug will only fit into a grounding type power outlet This is a safety feature If you are unable to insert the plug into the outlet contact you electrician to replace your obs
19. olete outlet Do not defeat the safety purpose of the grounding type plug POWER CORD PROTECTION Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and point where they exit from the product PROTECTIVE ATTACHMENT PLUG The product is equipped with an attachment plug having overload protection This is a safety feature See Instruction Manual for replacement or resetting of protective device If replacement of the plug is required be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug OUTDOOR ANTENNA GROUNDING If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and requirements for the grounding electrode UC 16 17 18 19 20 21 22 23 24 25 SEE FIGURE 5 ANTENNA LEAD IN WIRE ANTENNA DIS
20. sonnel DAMAGE REQUIRING SERVICE Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the product c If the product has been exposed to rain or water d If the product does not operate normally be following the operating instructions Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to damage and will often require extensive work by a qualified technician to restore the product to its normal operation e If the product has been dropped or damaged any way and f When the product exhibits a distinct change in performance this indicates a need for service REPLACEMENT PARTS When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards SAFETY CHECK Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition WALL OR CEILING MOUNTING The product should be mounted to a wall or ceiling only as r
Download Pdf Manuals
Related Search