PYLE Audio PDWM5300 User's Manual
Contents
1. coor 2 15300 UHF som amp CRAE aaa UHF su POWER LED SET UP DOWN POWER LED SET UP DOWN PLLI6CH UHF TRUE DIVERSITY WIRELESS MICROPHONE SYSTEM VOLUME PLL TAR UHF TRUE DIVERSITY WIRELESS MICROPHONE SYSTEM VOLUME PREFACE Thank you for buying the PDWM5300 Wireless System Please read through these operation instructions so you will know how to operate your model properly After you read it put it away ina safe place for future reference CONTENTS PI Precautions Pe Hand held microphone P3 Receiver PU Installation PS Trouble shooting PO Specifications PRECAUTIONS Avoid exposure of the system to rain or moisture No user serviceable parts inside the system Refer all servicing to a qualified technician only Handle the wireless system carefully dropping or other shocks may cause failure Avoid using the system where it may be subjected to heat such as direct sunlight near radiators or other heat sources Should any liquid be spilt on the system stop using it immediately It may be possible to dry the system but you should have it checked by a qualified technician before using it again Take care with the main power adapter and lead If damaged in any way do not use the system and refer to a qualified technician for repair Only use the system with the supplied components Do not attempt to use with any other main power supply adapter If the wireless system is not going to be used2. for a while remove the battery to prevent leakage In the event of electrolyte leakage inside the battery compartment carefully remove the leakage with a damp cloth Take care not to get battery electrolyte in contact with your skin however if it does wash your hands under a running tap If electrolyte comes into contact with your eyes seek medical advice immediately Only replace the battery with the same or an equivalent type Please dispose of old batteries in an environmentally friendly manner in accordance with the relevant legislation Do not use any solvents to clean any part of the wireless system HAND HELD MICROPHONE PARTS DESCRIPTION Mesh cartridgeinside Tube Power LED indicator Power and Mute switch Switchon and off the microphone Move the switchto middle positionto mute the mic Battery compartment Battery Cover CH selector ROD N OA OPERATION 1 Unscrew the battery cover at the end of the microphone Install the provided 2 1 5V batteries taking care to fit it with the correct polarity connected 2 According to frequency Chart on the battery cover adjust the CH selector to make the microphone to be the same frequency as receiver 3 Check the battery by switching the microphone ON The red LED will come on This indicates correct operation If the red LED is dim this indicates the battery is low and should be changed If the red LED does not come on at all it indicates the
3. is not Turn on the microphone receiver turned on and the connected audio equipment No Sonne The connected audio equipment is Turn on the audio equipment not turned on The speakers headphones are not Connect the speakers connected to the audio equipment headphones The battery in the wireless microphone is weak Replace ine Bakery The AUDIO OUT on the receiver i Adjust the volume controls is not set correctly The distance between the wireless Move the wireless microphone microphone and speakers are too away from the speakers or close change the direction of the A howling noise microphone heard from the speakers j The battery in the wireless microphone is weak meplace ME battery SPECIFICATIONS A Overall System Carrier Frequency UHF 795 805MHz Frequency Stabilization less than 30ppm Dynamic Range more than 90dB Total Harmonic Distortion less than 0 5 Frequency Response 40hz 15khz 3dB Audio Output Level separate type 0 400mV Mix Type 0 200mV B Receiver Power Supply DC 12V Consume Power AW Signal Noise Ratio more than 90dB Image amp Spurious Rejection more than 80dB Border upon Channel Rejection more than 80dB Receiving Sensitivity 10dBuv sinad 30dB De emphasis 50us C Transmitter Transmitting Power 8 5mW Modulation Type FM F3F Max Deviation 25KHz Spurious Emission more than 40dB with carrier Power Supply 3V
4. battery is dead and should be replaced FREQUENCY CHART PAAA ARA ARAA MLA ALA NA ll 123 4 123 4 1 2 123 4 1234 1234 234 CHOO CHO1 CHO4 CHOS CHOG CHO7 795 2MHz 795 8MHz 796 4MHz 797 0MHz 797 6MHz 798 2MHz 798 8MHz 799 4MHz AAA am pa S Ce Apolo 1234 1234 1234 1 1234 1234 3 11 CH12 CH13 CH14 CH15 MHz 802 4MHz 803 0MHz 803 6MHz 804 2MHz CHO8 CHO9 CH10 800 0MHz 800 6MHz 801 2MHz 801 8 RECEIVER PARTS DESCRIPTION Power Switch Turn on power switch the display of LCD will illuminate Power LED indicator Turn on power switch this indicator will illuminate SET Press once to adjust frequency by UP DOWN buttons Press again to exit UP Channel UP DOWN Channel DOWN LCD Display Volume control Antenna Aand B Balanced output 10 Unbalanced output 11 12V DC IN ONOARWND PYLE PDWM5300 e eee CO wW A F 800MHz CJ MIN e MAX CO OPERATION Connect the antennas A and B Make sure they are vertical 2 Insert one end of included audio cable into AF OUT on rear panel and the other end into LINE IN of amplifier or mixer 3 Connect the power adaptor from DC 12V of receiver to a main power socket 4 Switch on the receiver The power indicator comes on LCD display will illuminate Press SET once there will be a mark M displayed on LCD panel N
5. ow you can adjust frequency by UP DOWN buttons Press SET again to exit Make sure the microphone and receiver to be of same frequency 5 Switch on the microphone A letter A or B will appear in the top right of the LCD indicating the diversity reception RF strength in dB is indicated in the bottom left corner of the display When you speak into the microphone AF signal will display on the bottom of LCD display panel INSTALLATION Using the supplied audio cable connect from the AF OUT jack socket to the LINE IN socket on amplifier Alternatively you can connect an XLR cable to the XLR balanced output Connect the mains power adaptor from DC 12V jack to a suitable mains power socket Installation Location At least 3 ft above ground level At Least 3 ft away from wall AMPLIFIER PROFESSIONAL MIXER RECEIVER MAINS POWER ADAPTER IT SPEAKERS TROUBLE SHOOTING The wireless microphone is not reden Turn on the wireless microphone The microphone receiver is not Turn on the microphone receiver The on air turned on and the connected audio equipment e The microphone receiver is not Turn on the microphone receiver pep connected properly and the connected audio equipment Frequency not setcorrectly Make sure micand receiver are set to the same frequency The battery in the wireless microphone is weak Replace the battery The microphone receiver
Download Pdf Manuals
Related Search