Premier Mounts Prestige Ultra Flat Mount PRF User's Manual
Contents
1. A lt FLAT PANEL MOUNT Each mount comes with two VESA mounting plates one combination of 75 100 mm and one 75 mm only plate for smaller mounting surfaces All Prestige flat panel mounts easily support most VESA standard LCD flat panels on the market today PRF FLAT PANEL MOUNT Features Mount comes in both VESA 75 and VESA 100 models Stands 750 off the wall Lbs 1 Description Qty Size Wood screws 4 10 x 1 1 4 Anchors 4 10 Handy box screws 2 6 32 x 1 Monitor screws 4 M4 x 10 mm Security screws 2 M6 x 12 mm Monitor screws 4 M4 x 20 mm Nylon spacers 4 5 If the screws supplied require being longer than M4 x 10 mm for your monitor use commercially available suitable hardware to complete your installation For monitors with a recessed VESA 75 use the four M4 x 20 mm Phillips screws and the 5 nylon spacers supplied gt 4 PREMIER om MOUNTS The original holding company ADIVISION OF PROGRESSIVE MARKETING INC 3130 E Miraloma Ave Anaheim CA 92806 Phone 800 368 9700 Fax 800 832 4888 Visit us at www premiermounts com 1 IN PRF R1 WARNING The wall should be capable of supporting a weight of at least 50 Ibs If it cannot the wall must be reinforced Proper installatio procedure by qualified personnel as outlined in the installation instructions must be adhered to Failure to do so could result 1 serious personal injury It is stro2. compensate for the indentation Then SR secure both plates as shown on single stud or solid structure diagrams Thank you for choosing PREMIER MOUNTS for your installation needs If you have any questions please contact PREMIER MOUNTS INC information is shown on the front of this page
3. e front plate top flange opening before letting go of the monitor Slide down and push in To secure the two plates install the two 2 M6 x 12 mm securing screws to the bottom of the plates using a long Phillip head screwdriver If you have a recessed VESA 75 the four 4 5 nylon spacers and the four 4 M4 x 20 mm Phillips must be used to follow the single stud Or the solid structure installation methods to complete the installation CAUTION Do not over tighten the M4 screws to the monitor Failure to do so could result in damaging the threads and monitor SINGLE STUD SOLID STRUCTURE X i ZN Pa wee ae MONITOR SCREWS MONITOR MONITOR SCREWS oa el a M4 x 10 MM WOOD STUD ae sf M4 x 10 MM A ib ee ELECTRICAL OPENING ae PLASTIC ANCHORS Soe z lt a sete lt d P A WU T S Z a n vara SOLID a T nh WALL coN l ge BACK Eos BACK lt PLATE Sa PLATE STURE a J ace 10 WOOD SCREW FRONT PLATE PaaS SOLID FRONT PLATE WF jl M6 x 12 MM WALL M6 x 12 MM SECURITY SCREWS STRUCTURE SECURITY SCREWS 10 WOOD SCREW a N RECESSED VESA 75 LA MONITOR SCREWS wia M4 x 20 MM MONITOR yy 5 NYLON SPACERS 7 FRONT PLATE NOTE Use the four 4 5 nylon spacers and four 4 M4 x 20 mm if you have a recessed VESA 75 monitor to
4. for your installation needs Secure the front plate to the monitor using the four 4 M4 x 10 mm Phillip screws supplied The flange opening must be facing up and the flat surface touching the flat panel surface Raise the monitor with the front plate attached and slip the top flange opening to the flange on the back plate Slide the monitor down slowly Make sure the back plate flange captures the front plate top flange opening before letting go of the monitor Slide down and push in To secure the two plates install the two 2 M6 x 12 mm securing screws to the bottom of the plates using a long Phillip head screwdriver Use the four 4 mounting points on the back plate Choose the wall where the monitor will be located Level and mark with a pencil the four 4 mounting points found on the back plate Drill four 4 1 16 pilot holes for the plastic anchors then secure the wall bracket with the four 4 10 x 144 screws supplied to the anchors All electrical wiring should be done at this time use the two 2 6 32 x 1 handy box screws supplied for your installation needs Secure the front plate to the monitor The flange opening must be facing up and the flat surface touching the monitor surface Secure using the four 4 M4 x 10 mm Phillip screws supplied Raise the flat panel with the front plate attached and slip the top flange opening to the flange on the back plate Slide the monitor down slowly Make sure the back plate flange captures th
5. ngly recommended that two people perform the installation procedures CAUTION The entire installation instructions should be fully read and understood including all of the safety symbols an safety precautions before beginning installation The installation instructions should be read understood and followed to prever personal injury or property damage Keep these installation instructions in an easily accessible location for future reference Indicates that the power plug is to be disconnected from the power outlet Safety precautions must be taken at all times Warning and caution in general INSTALLATION INSTRUCTIONS PRF Step 1 Check that you have all the hardware listed on the front of the page If any of the hardware described is missing on your particular model do not continue contact PREMIER MOUNTS INC shown on the front cover Separate the plates and choose the location for the monitor and follow any safety and precautions from the monitor s manufacturer For single wood studs use the two 2 middle mounting points found on the back plate Locate the center of the wood stud behind the wall mark the height and location desired Drill two 2 1 8 pilot holes on the marked wall Secure the back plate to the center of the wood stud by using two 2 of the 10 wood screws supplied All electrical wiring should be done at this time use the two 2 6 32 x 1 handy box screws supplied
Download Pdf Manuals
Related Search