Pelco CM9760-KBD-E80 User's Manual
Contents
1. he Move the joys ify that he Move the joys Veri fy that he Move the joysti Veri fy that he Save the joyst b E d e f g Ver h i J k m Ret Melle hk JOYSTICK SETUP XXX XXX XXX XXX XXX XXX a nn n STEP wel STEP EXIT r SELECT SCROLL UP SCROLL DOWN ck ICON ICON ICON MOVE CURSOR MOVE CURSOR SAVE ICON CYCLE SELECTIONS CYCLE SELECTIONS LEFT ICON RIGHT ICON Figure 3 Joystick Setup Menu in the central default position select the Keyboard Select icon pan and tilt center values xxx xxx are between 122 and 134 ic le ic ic fully to the left and then select the Move Cursor Cycle Selections Left icon t value is between 90 and 98 fully to the right and then select the Move Cursor Cycle Selections Right icon right value is between 158 and 166 fully down and then select the Backward Step Scroll Down icon down value is between 90 and 98 IC urn to the Se fully up and then select the Forward Step Scroll Up icon up value is between 158 and 166 ick configuration by selecting the Save icon up menu by selecting the Exit icon Using System Manager download the keyboard setup information to the KBD C1543M A 7 04 UPGRADING CM9760 KBR FIRMWARE CAUTION Only qualified personnel observing electrostatic discharge ESD precautions should perform the procedure Z N below Always wear a grounding strap connec2. 4 NOTCHED END OF EPROM ALIGNMENT NOTCH C1543M A 7 04 Remove the existing U3 EPROM chip refer to Figure 2 from its socket using the provided extraction tool Remove the chip slowly to avoid damaging the socket Remove the replacement EPROM chip from the electrostatic bag and inspect the chip to confirm that the pins are straight As illustrated in Figure 2 orient the chip using the alignment notch as a guide Verify pin to socket alignment and then carefully press the chip into its socket until the chip is completely seated Reattach the bottom cover to the KBD using the nine Phillips screws Reset the keyboard to factory default settings by doing the following a b With the KBD remaining powered off set DIP switches 1 2 and 8 to the ON position Power on the KBD by reconnecting the cable to the COM 1 port The Diagnostics mode display appears Power off the KBD by disconnecting the cable from the COM 1 port Set DIP switches 1 and 8 to the OFF position Power on the KBD by reconnecting the cable to the COM 1 port M x U3 U5 Pi CIRCUIT p BOARD U3 EPROM CHIP Figure 2 U3 EPROM Chip 11 Calibrate the joystick as follows a In Setup mode select the Joystick Adjust icon The Joystick Setup menu appears refer to Figure 3 With the joysti Veri fy that he Move the joys Veri fy that
3. INSTALLATION MANUAL System 9760 KBD KBR Firmware Upgrade CM9760 KBD E80 C1543M A 7 04 INTRODUCTION C1543M A 7 04 The System 9760 keyboard upgrade kit CM9760 KBD E80 provides the following items to upgrade CM9760 KBD CM9760 KBR firmware to version 8 03 1 U3 EPROM chip version 8 03 part number IC53 0043 0803 1 Chip extraction tool part number ICPULLERTOOL This manual provides instructions to upgrade CM9760 KBD CM9760 KBR firmware from version 7 8 or earlier to version 8 03 To upgrade CM9760 KBD firmware see the section titled Upgrading CM9760 KBD Firmware To upgrade CM9760 KBR firmware see the section titled Upgrading CM9760 KBR Firmware UPGRADING CM9760 KBD FIRMWARE CAUTION Only qualified personnel observing electrostatic discharge ESD precautions should perform the procedure below Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic components Handle circuit boards by their edges To upgrade CM9760 KBD firmware to version 8 03 do the following 1 Using System Manager upload user entered keyboard setup information to the System Manager database the KBD is reset later in this procedure After the KBD is reset you can download the setup information from NOTE This step is necessary to avoid loss of user programmed keyboard setup information which is erased when System Manager to the KBD as directed later in this procedure 2
4. Log off the KBD and then turn the KBD over so that the bottom of the KBD is visible refer to Figure 1 3 Disconnect the KBD from the 9760 system by unplugging the cable from the COM 1 port of the KBD 4 Set DIP switch 7 to the correct position e For compatibility with CM9760 CC1 and CM9760 MGR versions 7 80 003 to 7 80 029 set DIP switch 7 to the OFF position e For compatibility with CM9760 CC1 and CM9760 MGR version 8 03 006 or later set DIP switch 7 to the ON position 5 Remove the bottom cover of the KBD a Unscrew nine Phillips screws as indicated in Figure 1 Note that on some KBDs one of the screws has a plastic retaining nut as indicated in Figure 1 Remove that screw after you remove the other eight screws To remove the screw that has a plastic retaining nut do the following 1 Lift off the bottom cover of the KBD slightly 2 Locate the nut and while holding the nut with your fingers to prevent the nut from turning remove the screw b Gently lift off the bottom cover of the KBD AN CAUTION Be careful not to detach any of the wires that are soldered to the surface of the circuit board CABLE MAY HAVE RETAINING NUT SCREW 9 DIP SWITCH 7 p 5 3 g olo G e ww 3333 Relay lC Com3 Com2 Comt Reset Options o e g a e N a b Figure 1 Bottom of CM9760 KBD 2 C1543M A 7 0
5. anel of the KBR by unscrewing 16 flat head and 4 pan head Phillips screws 5 flat head screws on top of panel 5 flat head screws on bottom of panel 3 flat head screws on each side of panel and 4 pan head screws on face of panel 7 Remove the existing U3 EPROM chip refer to Figure 6 from its socket using the provided extraction tool Remove the chip owly to avoid damaging the socket n 8 Remove the replacement EPROM chip from the electrostatic bag and inspect the chip to confirm that the pins are straight 9 As illustrated in Figure 6 orient the chip using the alignment notch as a guide Verify pin to socket alignment and then carefully press the chip into its socket until the chip is completely seated 10 Reattach the rear panel of the KBR using the 16 flat head and 4 pan head Phillips screws 11 Reset the keyboard to factory default settings by doing the following a With the KBR remaining powered off set DIP switches 1 2 and 8 to the ON position b Power on the KBR by reconnecting the cable to the COM 1 port The Diagnostics mode display appears c Power off the KBR by disconnecting the cable from the COM 1 port d Set DIP switches 1 and 8 to the OFF position e Power on the KBR by reconnecting the cable to the COM 1 port CIRCUIT BOARD NOTCHED END OF EPROM ALIGNMENT NOTCH U3 EPROM CHIP Figure 6 U3 EPROM Chip 6 C1543M A 7 04 C1543M A 7 04 12 Calibrate the joystick a
6. eserved World Headquarters 3500 Pelco Way Clovis California 93612 USA USA amp Canada Tel 800 289 9100 Fax 800 289 9150 International Tel 1 559 292 1981 Fax 1 559 348 1120 www pelco com 1509001 Orangeburg New York Las Vegas Nevada Eindhoven The Netherlands Wokingham United Kingdom Montreal Canada Singapore
7. ion to the KBR WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on the following fixed camera models CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X hree years on all other fixed camera models including Camclosure Integrated Camera Systems and Genex Series multiplexers server and keyboard wo years on all standard motorized or fixed focal length lenses wo years on Legacy CM6700 CM6800 CM8500 CM9500 CM9700 Series Matrix DF5 and DF8 Series Fixed Dome products wo years on Spectra Esprit and PS20 Scanners including when used in continuous motion applications wo years on Esprit and WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders and NVR300 network video recorders One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reaso
8. n of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise he above warranty provides the Dealer with specific legal rights The Dealer may also ave additional rights which are subject to variation from state to state WARRANTY AND RETURN INFORMATION If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal t
9. o the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER If the goods are to be sent by a FREIGHT SERVICE send the goods to FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 REVISION HISTORY Manual Date Comments C1543M 4 03 Original version C1543M A 7 04 Pelco the Pelco logo and System 9760 are registered trademarks of Pelco Added factory default reset and joystick calibration information Copyright 2004 Pelco All rights r
10. s follows a In Setup mode select the Joystick Adjust icon The Joystick Setup menu appears refer to Figure 7 JOYSTICK SETUP XXX XXX XXX XXX XXX XXX Welles hk a un Ei STEP en STEP A ICON SELECT SCROLL UP SCROLL DOWN ICON ICON ICON MOVE CURSOR MOVE CURSOR SAVE ICON CYCLE SELECTIONS CYCLE SELECTIONS LEFT ICON RIGHT ICON Figure 7 Joystick Setup Menu b With the joystick in the central default position select the Keyboard Select icon c Verify that the pan and tilt center values xxx xxx are between 122 and 134 d Move the joystick fully to the left and then select the Move Cursor Cycle Selections Left icon e Verify that the left value is between 90 and 98 f Move the joystick fully to the right and then select the Move Cursor Cycle Selections Right icon g Verify that the right value is between 158 and 166 h Move the joystick fully down and then select the Backward Step Scroll Down icon i Verify that the down value is between 90 and 98 j Move the joystick fully up and then select the Forward Step Scroll Up icon k Verify that the up value is between 158 and 166 Save the joystick configuration by selecting the Save icon m Return to the Setup menu by selecting the Exit icon Mount the KBR into the rack and attach each rack ear of the KBR to the rack using two Phillips rack mounting screws for each ear Using System Manager download the keyboard setup informat
11. ted to an approved grounding source when working on or near exposed electronic components Handle circuit boards by their edges To upgrade CM9760 KBR firmware to version 8 03 do the following 1 Using System Manager upload user entered keyboard setup information to the System Manager database M NOTE This step is necessary to avoid loss of user programmed keyboard setup information which is erased when the KBR is reset later in this procedure After the KBR is reset you can download the setup information from System Manager to the KBR as directed later in this procedure 2 Log off the KBR 3 Disconnect the KBR from the 9760 system by unplugging the cable from the COM 1 port on the rear of the KBR refer to Figure 4 4 Remove the KBR from the rack by unscrewing the two Phillips rack mounting screws from each rack ear on the front of the KBR refer to Figure 5 PAN HEAD SCREW 4 FLAT HEAD SCREW zus Y T P Y Y DIP SWITCH 7 Sas A 4 amp 4 48 Figure 4 Rear of CM9760 KBR Figure 5 Front of CM9760 KBR C1543M A 7 04 5 5 Locate DIP switch 7 on the rear of the KBR refer to Figure 4 and set the DIP switch to the correct position e For compatibility with CM9760 CC1 and CM9760 MGR versions 7 80 003 to 7 80 029 set DIP switch 7 to the OFF position e For compatibility with CM9760 CC1 and CM9760 MGR version 8 03 006 or later set DIP switch 7 to the ON position 6 Remove the rear p
Download Pdf Manuals
Related Search