Pelco PT180-24SL User's Manual
Contents
1. PT180 24P PT180 24SL Light Duty Pan Tilt Installation Operation Manual C314M D 8 98 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 CONTENTS Section Page 10 GENERAL usina A ALA EE EDGE 3 1 1 IMPORTANT SAFEGUARDS AND WARNINGS 3 3 0 INSTALLATION 3 1 MOUNTING 3 2 CAMERA ENCLOSURE MOUNTING 3 3 WIRING siate 3 3 1 Mating Connector Assembly 3 4 LIMIT STOP ADJUSTMENT 4 0 OPERATION itte d 10 5 0 TROUBLESHOOTING 5 1 SERVICE MANUAL 6 0 MAINTENANCE 6 1 TIGHTENING DRIVE CHAINS eene 12 6 2 CHAIN DRIVE LUBRICATION essere 12 4 0 SPECIFICATIONS Cent e eere II netos 13 8 0 WARRANTY AND RETURN INFORMATION eee 16 LIST OF ILLUSTRATIONS Figure Page 1 Connector Assembly nennen 7 2 PT180 24P PT180 24SL Wiring Diagram 8 3 Limit Stops icr 9 4 Mounting Dimensions esses 14 LIST OF TABLES Table A Maximum Cable Distances to Wire Pan and Tilt Motors B Recommended Cable Distances Using RB24 Relay Box REVISION HISTORY Manual Date Comments C314M D 8 98 Changed manual to new format Added certifications Re vised installation instructions Moved exploded assembly diagram a2. 3 962 m 160 48 77 m MPTA24DT MPTAZ24DT REQUIRES EXTERNAL POWER SUPPLY 6 Pelco Manual C314M D 8 98 NOTE Contacts cannot be re moved from the connector without the use of the appropriate AMP ex traction tool ZT305183 which is available from Pelco NOTE When a pan tilt is mounted in the inverted position the LEFT RIGHT and UP DOWN functions are reversed during operation To correct this problem reverse the LEFT RIGHT functions in the con trol cable pins 3 and 7 at the par tilt or control and the UP DOWN functions pins 5 and 6 at the pan tilt or control Pelco Manual C314M D 8 98 3 3 1 Mating Connector Assembly To assemble the mating connector refer to Figure 1 and perform the following steps 1 Figure 1 Slide the connector clamp assembly over the conductor cable If the diameter of the conductor cable is such that the rubber boot will slide over it easily slide the rubber boot onto the conductor cable at this time If not discard the rubber boot Refer to Detail A in Figure 2 Prepare the wires from the conductor cable as follows a Strip at least 1 inch 2 54 cm from the cable jacket to expose the wires You may need to strip more from the cable jacket if you have more wires b Strip 1 8 inch 0 125 cm from each wire c Using an AMP style crimper crimp the wires and their insulation to the connector pins Slide the connector pins into the appropriate holes in th
3. Cable distances for pan and tilt motors should not exceed the distances specified in Table A Cable fabrication must be in accordance with Section 3 3 1 Mating Connector Assembly The following are some recommended common installa tion practices 1 Always use jacketed stranded multi conductor interconnecting cable between the control and the pan tilt unit with additional conductors than needed for future servicing and or additions 2 Always use color coded conductors for ease of wiring and to identify functions at a later date 3 Keep a wiring diagram with the system for later use and reference Table A Maximum Cable Distances to Wire Pan and Tilt Motors 6 Conductors 7 Conductors 65 ft 19 81 m 85 ft 25 91 m 100 ft 30 48 m 135 ft 41 15 m 160 ft 48 77 m 220 ft 67 06 m Using 2 wire motor common Cable distances are for both motors running and assuming a 10 voltage drop in the cable Six conductor cable single common conductor is recommended Distances are approximate maximum recommended under the following conditions Simultaneous pan tilt activation Minimum 21 6 volts at pan tilt Operating distance may be extended by using an RB24 remote relay box Refer to Table B for extended cable distances Table B Recommended Cable Distances Using RB24 Relay Box Maximum Maximun Distance feet Distance feet ar pr 5 800 1 768 m 65 19 81 m 8 250 2 515 m 100 30 48 m MPT24DT 13 000
4. Esprit and WW5700 Series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video products months on DX Series digital video re corders NVR300 Series network video recorders Endura Series distributed network based video products and TW3000 Series twisted pair transmission products One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the spe cific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential
5. Lens Camera AC Movement in horizontal plane PT180 24P 0 355 PT180 24SL 360 9 sec 1 No load condition 90 movement in vertical plane 3 sec 5 No load condition 20 lb 9 08 kg at 5 inches 12 7 cm from tilt table surface to center of gravity upright or inverted Chain and sprocket pan drive worm gear tilt drive Heavy duty ball bearings Oilite bronze bushing 50 duty cycle 30 minute rating 24 VAC 50 60 Hz Running 38 amp 9 2 vA 9 amp 21 6 vA Starting 46 amp 11 1 vA 1 35 amp 32 4 vA Amp CPC type mate supplied installed onto a pigtail exiting from the base of the unit all functions camera power lens video pan tilt Hirschmann MAB6100 Two phase induction type instantaneous reversing Pan and Tilt 5 amp External adjustment As listed plus coax cable 6 or 7 Left right up down motor common safety ground 4 2 13 GENERAL Construction Aluminum casting and plate all internal parts corrosion pro tected Environment Indoor 10 to 120 F 23 33 to 48 89 C Dimensions See Figure 4 Weight Unit Shipping PT180 24P 20 Ib 9 kg 22 Ib 9 96 kg PT180 24SL 21 Ib 9 51 kg 23 lb 10 41 kg Design and product specifications subject to change without notice 281 71 X 656 1 67 OBROUND 2X ele Seo 281 71 ARE 3 2 37 6 02 la 7005 17 78 VIDEO amp CAMERA POWER CABLE 2807
6. applicable ratings NEMA Type 1 IP 20 Pelco Manual C314M D 8 98 3 0 INSTALLATION CAUTION Pan tilts in the PT180 Series are de signed for upright or in verted operation and should never be mounted horizontally CAUTION Pan tilts in the PT180 Series are designed to oper ate at 24 volts AC Input voltage must not exceed 28 volts or drop below 22 volts or else damage will occur Pelco Manual C314M D 8 98 Pan tilts in the PT180 Series are designed to mount onto a horizontal surface in the upright or inverted position In order to ensure proper wiring and system operation of all components it is highly recommended that the pan tilt and the associated control equipment is tested in your facility before field installation Refer to Sections 3 3 and 3 4 3 1 MOUNTING Attach the pan tilt unit to a mount following the instructions that accompany the mount To ensure maximum pan travel mount the pan tilt so that the fixed limit stop is directly opposite the center of the intended viewing area Make sure the mounting surface and the mounting method is strong enough to sup port four times the combined weight of the pan tilt enclosure camera and lens 3 2 CAMERA ENCLOSURE MOUNTING Attach the enclosure camera and lens to the pan tilt unit with 1 4 20 hardware not supplied The enclosure camera and lens must be correctly mounted and balanced on the tilt table for proper operation 3 3 WIRING
7. damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty condi tions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located w
8. stop against the actuator until it clicks indicating that the limit switch has opened Lock the stop in place Pan the unit to the desired left position Adjust the left pan limit stop as de scribed in step 3 Pan left and right to both limit stops and check for exact positioning Tighten both stops securely Remove the cover plate from the left side of the tilt table Turn on the control unit if you are starting at this step Loosen the limit stop screws and tilt the table to the desired up position Move the up limit stop until it touches the tilt limit switch actuator Push the stop against the actuator until it clicks indicating that the limit switch has opened Lock the stop in place Tilt the table to the desired down position and set the stop as described in step 7 Tilt the table up and down and check for exact positioning Tighten both stops securely Replace the cover plate NOTE COVER PLATE NOT SHOWN IN THIS ILLUSTRATION TILT DOWN LIMIT STOP TILT UP LIMIT STOP PAN LIMIT SWITCH ACTUATOR PAN RIGHT LIMIT STOP PAN LEFT FIXED LIMIT STOP LIMIT STOP Figure 3 Limit Stops 4 0 OPERATION Refer to the manual for your control equipment for operating the pan tilt unit 10 Pelco Manual C314M D 8 98 5 0 TROUBLESHOOTING Pelco Manual C314M D 8 98 Some common problems encountered with pan tilt systems include miswiring over loading and not using the units for the correct applicat
9. E RISK OF ELECTRICAL SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Please thoroughly familiarize yourself with the information in this manual prior to installation and operation Pelco Manual C314M D 8 98 3 2 0 DESCRIPTION The PT180 24P and PT180 24SL are light duty indoor pan tilt units capable of handling all enclosure camera and lens combinations up to 20 lbs 9 08 kg in weight The PT180 24P and PT180 24SL are equipped with 24 VAC motors and both can be mounted for inverted operation The PT180 24SL has the added feature of 360 pan rotation and both pan tilts are pre wired for all control functions pan tilt motorized zoom lens camera power and video All connections are made at the input connector eliminating the need for wiring harnesses Both units are capable of auto random scan operation when used with an appropri ate controller Constructed of aluminum these units are to be operated in a protected environ ment 2 1 MODELS PT180 24P Light duty pan tilt 24 VAC PT180 24SL Light duty pan tilt with SL option 360 pan rotation 24 VAC 2 2 CERTIFICATIONS The products identified below have been tested and certified for agency compli ance as noted PEE Agency Compliance Certification Pes eco uu con Croze x x ecc e Applicable CE FCC UL and CSA cUL standards CE Class B UL Standard 2044 Additional
10. e connector body until they snap into place Refer to detail B in Figure 1 and to Figure 2 for correct pin arrangement Push the connector clamp assembly with boot if used toward the connector body Screw the clamp assembly onto the connector body being careful not to disturb the wires To complete the assembly attach the appropriate clamp with the screws pro vided and tighten FRONT VIEW Connector Assembly INPUT CONNECTOR COMMON LEFT VIDEO VIDEO SHEILD CAMERA CAMERA AC IRIS FOCUS ZOOM LENS COMM SFTY GRND Figure 2 PT180 24P PT180 24SL Wiring Diagram 8 Pelco Manual C314M D 8 98 WARNING Do not operate pan tilt with out limit stops Do not attempt to adjust the limit stops while the unit is operating Personal injury or damage to the unit may result Do not remove or re position the fixed limit stop on the pan tilt DAMAGE WILL OC CUR NOTE The PT180 24SL does not have pan limit stops Disregard steps 1 5 Pelco Manual C314M D 8 98 3 4 LIMIT STOP ADJUSTMENT To set pan tilt limit stops perform the following steps Refer to Figure 3 1 2 Loosen the pan limit stops Turn on the control unit Pan the unit to the right until the desired right pan limit is reached Move the right pan limit stop until it touches the pan limit switch actuator Push the
11. gt 22 53 9 LONG 10 87 hi 27 61 LENS CONNECTOR bi 5 75 Am 14 61 9 37 2380y PA 4 75 1 4 20 D amp T Y gt 1207 y JE SPACED ON A 2 50 1 25 3 18 1 00 2 54 B C 3X 6 35 4 312 79 PT180 24P SLOT 2X MOUNTING DIM PT180 24SL MOUNTING DIM A PT180 24P NOTE VALUES IN PARENTHESES ARE CENTIMETERS PT180 24SL ALL OTHERS ARE INCHES Figure 4 Mounting Dimensions 14 Pelco Manual C314M D 8 98 NOTES Pelco Manual C314M D 8 98 15 8 0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workman ship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and CC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 Scanners including when used in continuous motion applications Two years on
12. ion If the pan tilt unit fails to operate do the following 1 Check the fuse in the control unit If the fuse is bad replace it 2 Ifthe fuse blows after replacing it check the control cable between the control unit and the pan tilt for shorts high resistance or opens 3 Ifthe control cable is good reconnect it to the control unit but not to the pan tilt Replace the fuse and operate the control unit If the fuse blows again the fault is in the control Refer to Figure 2 for the following steps 4 Ifthe control unit is good check the wiring harness in the pan tilt for shorts 5 If the wiring harness is good check the motor starting capacitors 6 If the starting capacitors are good check the motors for opens and shorts There should be low resistance between the windings 7 Checkthe limit switches for opens and shorts 5 1 SERVICE MANUAL If you need to service your unit obtain a service manual in one of the following ways Go to Pelco s web site at http www pelco com and find service manual C323SM Contact Pelco s Literature Department and request service manual C323SM 11 6 0 MAINTENANCE 12 Inspect the pan tilt unit every six months to ensure trouble free operation and an extended product life Harsh environments and or continuous motion applications may require more frequent maintenance Please read all of the instructions that follow before servicing the pan tilt To begin re
13. ithin the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to Pelco 3500 Pelco Way Clovis CA 93612 5699 USA If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco c o Expeditors 473 Eccles Avenue South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Spectra Esprit Genex Legacy and Camclosure are registered trademarks of Pelco TM Endura and ExSite are trademarks of Pelco O Copyright 1998 Pelco All rights reserved 16 Pelco Manual C314M D 8 98
14. move the three screws on the front of the pan tilt housing and lift the cover to gain access to the pan and tilt motor assemblies 6 1 TIGHTENING DRIVE CHAINS Check the pan and tilt drive chains for tension A movement of 1 32 of an inch to 3 32 of an inch in the chains is acceptable If the movement of a chain exceeds 3 32 of an inch adjust the chain as follows 1 Loosen the screws securing the motor to the mounting frame 2 Pryon the motor to apply tension to the chain Do not over tension the drive chain 3 Keep tension on the chain while tightening the screws 6 2 CHAIN DRIVE LUBRICATION Sprockets chains and gears should be well greased If necessary lubricate the pan and tilt gears sprockets and chains as follows with a high quality grease ca pable of withstanding temperatures from 50 to 170 F 46 to 77 C Do the fol lowing 1 Liberally apply grease to the pan and tilt gears chains and sprockets 2 Operate the pan and tilt motors to spread the grease across the parts 3 Apply additional grease if necessary 4 Reinstall the cover Pelco Manual C314M D 8 98 7 0 SPECIFICATIONS Pelco Manual C314M D 8 98 MECHANICAL Pan Speed Tilt Speed Maximum Load Gearing Bearings Pan Tilt Duty Cycle ELECTRICAL Input Voltage Power Requirements Pan Tilt Pan Tilt Connectors Pan Tilt Lens Motors Limit Switches Pan and Tilt Conductor Requirements Pan Tilt
15. nd parts lists to maintenance service manual Revised Troubleshooting and Maintenance sections Pelco Manual C314M D 8 98 1 0 GENERAL 1 1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by qualified service personnel and conform to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclosure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 3 The weight of the camera lens and enclosure shall not exceed 20 Ib 9 08 kg 4 Only use replacement parts recommended by Pelco 5 After replacement repair of this unit s electrical components conduct a resis tance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry 6 The installation method and materials should be capable of supporting four times the weight of the enclosure pan tilt camera and lens combination The product and or manual may bear the following marks This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit maintenance instructions in the literature accompanying this unit i This symbol indicates that there are important operating and CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE TH
Download Pdf Manuals
Related Search