Pelco DX9000 User's Manual
Contents
1. DX9000 Series Video Storage Unit Installation Operation Manual M C684M A 7 01 LISTED Pelco 3500 Pelco Way Clovis CA 93612 5699 USA Pelco Online www pelco com In North America and Canada Tel 800 289 9100 FAX 800 289 9150 DataFAX 800 289 9108 International Customers Tel 1 559 292 1981 FAX 1 559 348 1120 DataFAX 1 559 292 0435 PelcoEurope BV Dillenburg Center Dillenburgstraat 7C 5652 AM Eindhoven The Netherlands Tel 31 40 251 9870 FAX 31 40 251 9835 DESCRIPTION The DX9000 Series Video Storage Unit is one of the components of the DX9000 Series Digital Video Recorder system The storage unit contains hard disks for storing video infor mation from the DX9000 Series Digital Video Recorder A total of four storage units can be connected to each recorder MODELS DX9219HDD Storage unit with three hard disk drives totaling 219 GB DX9438HDD Storage unit with six hard disk drives totaling 438 GB DX9657HDD Storage unit with nine hard disk drives totaling 657 GB INSTALLATION READ BEFORE BEGINNING YOUR INSTALLATION The DX9000 system consists of three major components digital video recorders also referred to as servers video storage units and ViewStations computers Each piece of equipment is boxed separately and comes with its own documentation Make sure all parts are present Video Storage Unit SCSI cable Power cords 1 USA standard and 1 European standard Adjustable sup2. To install a storage unit in an equipment rack 1 Attach the two adjustable support rails to the sides of the equipment rack Refer the Figure 1 Use the eight 10 32 x 375 inch screws If the rack does not have threaded mounting holes also use the eight 10 32 nuts 2 Place the unit on the support rails and fasten the rack ears to the rack with the four 10 32 x 750 inch black Phillips pan head screws 10 32 X 375 SCREWS LEAVE SCREWS LOOSE UNTIL SUPPORT RAILS ARE ATTACHED TO THE RACK THEN TIGHTEN RIGHT SIDE MAKE SURE ARROWS FACE TOWARDS THE FRONT OF THE RACK SLIDE FRONT TO BACK TO ADJUST RAILS TO THE CORRECT DEPTH OF RACK LEFT SIDE Figure 1 Installation of Support Rails 00773 Pelco Manual C684M A 7 01 CONNECTIONS One two three or four video storage units can be connected to a recorder depending on the reguirements of your system NOTE All video storage units connected to a recorder must be turned on before turning on the recorder Pelco Manual C684M A 7 01 Refer to Figure 2 to install the storage units 1 Connect the appropriate end of the SCSI cable to the SCSI connector on each video storage unit Read the Caution Notice in the Mounting section Connect the other end of the SCSI cable from each video storage unit to the SCSI connector in slot 1 of the re corder Connect the first storage unit labeled 01 to the upper left connector Connect the second st
3. Resolution NTSC PAL Compression Compressed Image Size Remote Control MECHANICAL SCSI Connector GENERAL Operating Temperature Relative Humidity Dimensions Desktop Rack Mount Unit weight 100 240 VAC 50 60 Hz auto ranging 250W maximum 352 x 240 pixels 384 x 288 pixels MPEG1 352 x 240 average 1 4 kB Full remote control via TCP IP network Recorder interface 41 to 104 F 5 to 40 C Maximum 8096 non condensing 7 3 H x 17 0 W x 19 6 D inches 18 5 x 43 2 x 49 8 cm 7 0 H x 19 0 W x 19 6 D inches 17 8 x 48 3 x 49 8 cm 45 lb 20 4 kg maximum fully equipped Design and product specifications subject to change without notice REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class A digital de vice pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial envi ronment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense WARRANTY Pelco will repair or replace without charge any merchandise prove
4. al Date C684M 4 01 C684M A 7 01 Comments Original version Pelco the Pelco logo Spectra Genex and Legacy are registered trademarks of Pelco Esprit and Camclosure are trademarks of Pelco 4 Revised Description Installation and Connections sections Added FCC notice Copyright 2001 Pelco All rights reserved Pelco Manual C684M A 7 01
5. d defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on Pelco manufactured cameras CC3500 CC3600 and MC3500 MC3600 Series two years on all other cameras Three years on Genex Series multiplexers server and keyboard Two years on all standard motorized and fixed focal length lenses Two years on Legacy Camclosure Camera Systems CM6700 CM6800 CM8500 CM9500 CM9740 CM9750 CM9760 Matrix DF5 Series and DF8 Fixed Dome products Two years on Spectra and Esprit including when used in continuous mo tion applications Two years on WW5700 series window wiper excluding wiper blades Eighteen months on DX Series digital video recorders Six months on all pan and tilts scanners or preset lenses used in continu ous motion applications that is preset scan tour and auto scan modes Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s li ability for any claim whether based on breach of contract negligence infringe ment of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages includ ing loss of use loss of profit and claims of third parties however caus
6. ed whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state WARRANTY AND RETURN INFORMATION If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair Goods returned for repair or credit should be clearly identified with the assigned CA RA number and freight should be prepaid All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Ship freight prepaid to Pelco 3500 Pelco Way Clovis CA 93612 5699 REVISION HISTORY Manu
7. orage unit labeled 02 to the upper right connector Connect the third storage unit labeled 03 to the lower left connector Connect the fourth storage unit labeled 04 to the lower right connector Select the appropriate power cord USA or European standard and plug it into the power receptacle on the back of each video storage unit Plug the other end into a power supply preferably through an uninterruptible power supply Turn on the power switch on the back of one of the video storage units Then open the front door with the supplied key Press the square button to turn on the power Close the door The LEDs on the front of the unit light to show the hard drives are working Repeat step 4 for each storage unit Turn on the power switch on the back of the recorder Then open the front door with the supplied key Press the square button to turn on the power Close the door Go to the System Configuration section of the Installation Operation Manual for the Digital Video Recorder to continue with the installation procedure RECORDER STORAGE UNITS ARE NUMBERED AND MUST BE CONNECTED TO THE PROPER CONNECTOR Figure 2 Connection Storage Units to Recorder dcn SPECIFICATIONS ELECTRICAL VIDEO Input Voltage Power Consumption Recording
8. port rails Screws 10 32 x 375 inch 10 32 nuts Screws 10 32 x 750 inch Phillips pan head with washers Keys MAOONN It is important that the equip MOUNTING ment be installed in the proper sequence Get the manuals for all three types of equipment Keep the manuals together because you will have to go back and forth between the manuals as you install the equipment Start the installation with the recorders Refer to the Installation Operation Manual for the Digital Video Recorder CAUTION Each storage unit has been pre configured to operate with a specific recorder The storage units must be con nected to the proper recorder and in the proper order for the system to operate properly There is a label on the outside of the packing box and also on the rear panel of the equipment The recorder s label will have a name followed by a number 1 2 3 etc The storage unit s label will have the same name followed by two sets of numbers for example 1 01 The first number is the recorder to which the storage unit is to be connected The second number designates the SCSI connection location on the rear panel of the recorder For this reason consider mounting the recorder and storage units in a logical order Install all storage units that will connect to the same recorder The video storage unit may be placed on a flat surface such as a shelf or it can be installed in a 19 inch 48 26 cm equip ment rack
Download Pdf Manuals
Related Search