Pelco pelco c24407m-g User's Manual
Contents
1. 03 Mounting Directly to Concrete Wall or Ceiling 1 Attach the base to the wall or ceiling hardware not supplied 777 71 777 AZ LED 2 Do one of the following MUN TNR a Not Using Side Conduit NOT SUPPLIED Opening Verify the set screw and side conduit cover are tight OR b Using Conduit to Side Opening Loosen the set screw and remove the conduit plug 3 Install a 3 4 inch 1 91 cm conduit fitting and tighten the set screw 4 Pull video and power wires into the base Mounting to a 4S Electrical Box 1 Attach the ICS100 AP adapter 45 ELECTRICAL plate not supplied to the 4S box ind with the two 8 32 x 750 inch flat i CONCRETE WALL OR CEILING BASE CONDUIT PLUG WALL OR CEILING head screws E 8 32 X 750 FLAT HEAD 1 i 2 Pull video and power wires SCREW SUPPLIED into the base and attach the base to the adapter plate with the three 8 32 x 375 inch pan 8 32 x 375 PAN usi head Screws SCREW SUPPLIED Mounting to a Plaster Ring Pull video and power wires into the base and attach the base to the BOX VN plaster ring Use the two 8 32 x 750 inch CALATA pan head screws to attach the base to a 401 plaster ring Use the three 6 32 x 750 inch SCREW SUPPLIED pan head screws to attach the See nents base to a 404 plaster ring Connect Video and Power 1 Connectthe video cable COCA BASE WALL OR 401 OR 404 PLASTER RING2. G 5 03 11 PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defective in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Five years on FT FR8000 Series fiber optic products Three years on Genex Series products multiplexers server and keyboard Three years on Camclosure and fixed camera models except the CC3701H 2 CC3701H 2X CC3751H 2 CC3651H 2X MC3651H 2 and MC3651H 2X camera models which have a five year warranty Two years on standard motorized or fixed focal length lenses Two years on Legacy CM6700 CM6800 CM9700 Series matrix and DF5 DF8 Series fixed dome products Two years on Spectra Esprit ExSite and PS20 scanners including when used in continuous motion applications Two years on Esprit and WW5700 Series window wiper excluding wiper blades e Eighteen months on DX Series digital video recorders NVR300 Series network video recorders and Endura Series distributed network based video roducts One year except video heads on video cassette recorders VCRs Video heads will be covered for a period of six months Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from th
3. unit is specifically marked as a NEMA Type 3 3R 38 4 4X 6 or 6P enclosure it is designed for indoor use only and must not be installed where exposed to rain and moisture 3 Use only installation methods and materials capable of supporting four times the maximum specified load 4 Use stainless steel hardware to fasten the enclosure to outdoor surfaces 5 To prevent damage from water leakage when installing an enclosure outdoors apply sealant around the bolt holes between the enclosure and mounting surface DESCRIPTION The 100 Series Camclosure Integrated Camera System is a surface mount dome incorporating a camera and lens package into a small discreet high security enclosure designed for indoor outdoor areas that are subject to heavy vandalism INSTALLATION O Install Base Mounting Directly to Wall or Ceiling 1 Cuta small hole in the ceiling or wall for power and video wiring Use the adapter M P O R TA N T plate as a template To maximize 2 Pull video and power wires into the base id PET and attach the base to the wall or ceiling resistance hardware not supplied The electrical when not me opening in the base will accept a 3 4 inch using the 1 91 cm conduit fitting side conduit opening for wire connections verify that the conduit plug and set screw are tight A A n E Le Fi i WALL OR LN BASE MOUNTING HARDWARE NOT SUPPLIED 4 Pelco Manual C2407M G 5
4. 003 Pelco All rights reserved 12 Pelco Manual C2407M G 5 03
5. BASE 2 Depending on the input voltage connect either the 12 VDC or 24 VAC input power wires to the appropriate positions on the terminal block inside the base 3 12 VDC Operation Only power The camera is set for 24 VAC TERMINAS operation at the factory For 12 VDC operation remove the jumper from the 24 VAC 24 VAC JUMPER position and install it on the 12 VDG JUMPER 12 VDC position CONNECTOR HEATER CONNECTOR 1093 Pelco Manual C2407M G 5 03 5 CAUTION A Heater elements could be hot When camera power is on use caution when adjusting the camera This applies to all models Install Camera 1 Some indoor installations do not require a heater If the installation does not require a heater remove the heater board from the camera assembly To remove the heater apply pressure and press on the corner of the board N If the heater is installed plug the heater connector from the camera into the mating connector inside the base Plug the video connector from the camera into the mating connector inside the base Turn on power to the camera and monitor CONNECTOR 3 If you have a varifocal lens hold the assembly in your hand and point the lens toward what you want to view Loosen the focal length and focus locking screws Adjust according to scene detail Retighten the screws LOCKING SCREWS 4 Always make sure the tab on the camera bracket is pointing out of the enclosure away f
6. PELLO Installation Operation 100 Series Camclosure Integrated Camera System C2407M G 5 03 Pelco 3500 Pelco Way Clovis CA 93612 5699 USA www pelco com In North America and Canada Tel 800 289 9100 FAX 800 289 9150 International Customers Tel 1 559 292 1981 FAX 1 559 348 1120 2 Pelco Manual C2407M G 5 03 CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS DESCRIPTION INSTALLATION INSTALL BASE MOUNTING DIRECTLY TO WALL OR CEILING MOUNTING DIRECTLY TO CONCRETE WALL OR CEILING 5 MOUNTING TO A 4S ELECTRICAL BOX MOUNTING TO A PLASTER RING CONNECT VIDEO AND POWER INSTALL CAMERA INSTALL DOME AND TRIM RING ADJUSTMENTS COLOR CAMERA ONLY VERTICAL PHASE 24 VAC OPERATION ONLY AUTOIRIS LEVEL ADJUSTMENT etica daa daa recte rte FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS 9 SWITCH SETTINGS FOR VARIFOCAL LENS sisii iipasi 10 SPECIFICATION S itta ertet toa turn tte iaia 10 REGULATORYINOTICES a rai 11 WARRANTY AND RETURN INFORMATION eeeetntntn tnnt 12 Pelco Manual C2407M G 503 3 IMPORTANT SAFEGUARDS AND WARNINGS 1 Installation and servicing should be done only by qualified service personnel and conform to all local codes 2 Unless the
7. a written explanation with the product when returned Method of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authorization number CA number if returned for credit and RA number if returned for repair All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid Ship to the appropriate address below If you are located within the continental U S Alaska Hawaii or Puerto Rico send goods to Service Department Pelco 3500 Pelco Way Clovis CA 93612 5699 If you are located outside the continental U S Alaska Hawaii or Puerto Rico and are instructed to return goods to the USA you may do one of the following If the goods are to be sent by a COURIER SERVICE send the goods to If the goods are to be sent by a FREIGHT FORWARDER send the goods to Pelco Pelco c o Expeditors 3500 Pelco Way 473 Eccles Avenue Clovis CA 93612 5699 USA South San Francisco CA 94080 USA Phone 650 737 1700 Fax 650 737 0933 Pelco the Pelco logo Spectra Genex Legacy Esprit and Camclosure are registered trademarks of Pelco Endura and ExSite are trademarks of Pelco Copyright 2
8. e date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misuse alteration normal wear or accident are not covered under this warranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence infringement of any rights of any party or product liability relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties however caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment PO number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include
9. fications NTSC and EIA Models UL and cUL NTSC and PAL Color Models FCC Class B excluding auto iris models EIA and CCIR Monochrome Models FCC Class A excluding auto iris models PAL and CCIR Models CE Class B UL and cUL Design and product specifications subject fo change without notice Regulatory Notices FCC Class A monochrome EIA and CCIR cameras except auto iris models This equipment has been tested and found to comply with the limits of a Class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the in struction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to cor rect the interference at his own expense FCC Class B color NTSC and PAL cameras except auto iris models This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to part 15 ofthe FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency ener
10. gy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interfer ence by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help REVISION HISTORY Manual Date Comments C2407M 11 99 Original version C2407M 1 00 Revised installation instructions Added FCC notices C2407M A 1 00 Added varifocal lens Changed format C2407M B 7 00 Added information on dome liner C2407M C 1 01 Added information on conduit set screw and heater element caution C2407M D 7 01 Camera module redesigned reference ECO 01 7054 7055 7056 C2407M E 12 01 Manual revised to reflect product design revision C2407M F 7 02 Added instructions for fixed lens with auto iris C2407M G 5 03 Revised installation instructions bracket and camera assembled at factory Added iris level adjustment for fixed lens with auto iris Pelco Manual C2407M
11. h settings refer to procedures below 3 Replace the dome and trim ring Vertical Phase 24 VAC Operation Only Adjustment is required if there is vertical roll when switching between two cameras 1 Reverse the 24 VAC connections on one camera If both cameras are connected to the same trans former this should solve the problem 2 If reversing the connections does not solve the problem or if cameras are connected to different trans formers turn the adjustment screw on one camera while switching as rapidly as possible between the two camera views until the switching is clean and there is no vertical roll If more than two cameras are out of synchronization with each other choose one camera and synchronize all others to it FIXED LENS VARIFOCAL LENS VERTICAL PHASE ETICA ADJUSTMENT PHASE ADJUSTMENT Pelco Manual C2407M G 5 03 7 Auto Iris Level Adjustment If you have a varifocal lens or fixed focal length lens with an auto iris you can adjust the level setting to increase or decrease brightness VARIFOCAL LENS FIXED LENS y IRIS LEVEL Y IS ADJUSTMENT a AUTO IRIS LEVEL ADJUSTMENT Focus Adjustment for Fixed Focal Length Lens with Auto Iris CAUTION A Heater elements could be hot When camera power is on use caution when adjusting the camera To adjust the focus it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the lens To remove
12. ight compensation factory setting is used under varying lighting conditions such as outdoors or fixed lighting conditions where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots ALC ELC switch Always ELC FACTORY SETTINGS 9 Sa Y DC switch Not used lt gt lt Auto backlight compensation switch OFF en E ABL switch ON OFF Manual backlight compensation BLC switch ON a 8 E Es ABL switch OFF Bl SWITCH POSITION Pelco Manual C2407M G 5 03 9 Switch Settings for Varifocal Lens The high resolution camera with ifocal l d auto te 1 AWB Automatic white balance a as i hon s i 2 GAM Gamma function FACTORY SETTINGS ES ne ai P E 3 AGC Automatic gain control 12345678 eue Ge o 4 ESC Electronic shutter control HI B E E B 0 required It is also configured with E T BIN Backlight compensation 0 00000 CH 5 6 FL Flickerless OFF the shutter speed set at 1 60 7 AE Automatic exposure NTSC or 1 50 PAL and AGC Notused p Wi SWITCH POSITION set at 6 dB of gain To enable automatic exposure Turn on switch 7 and then turn on off switch 4 for electronic shutter control switch 5 for backlight compensation and switch 6 for flickerless motion To manually set and lock AWB Place a white background in front of camera and turn off swi
13. rom the ceiling or wall Gently squeeze the bracket place it against the shoulder inside the base and gently release Proper camera orientation CAMERA BRACKET TAB ALWAYS POINTS OUT OF THE ENCLOSURE TOP OF CAMERA BRACKET TAB ALWAYS POINTS OUT OF THE ENCLOSURE 1089 Wall Mounting The camera bracket tab points out of the enclosure and the top of the camera points up towards the tab Pelco Manual C2407M G 5 03 Ceiling Mounting The camera bracket tab points out of the enclosure and the top of the camera is pointed in the opposite direction Q Install Dome and Trim Ring 1 Align the screw holes in the trim ring with ADJUSTMENT those in the camclosure base DOME LINER 2 Domes with Liners only Position the viewing window over the lens of the camera LOOSEN SCREWS a Loosen the three Phillip screws located in the dome b Insert the blade of a standard screwdriver in one of the adjustment grooves Move dome into position c Tighten the three Phillip screws to lock liner in place 3 Tighten the tamper resistant screws with the supplied 1 8 inch hollow screwdriver bit ADJUSTMENTS COLOR CAMERA ONLY If you have a color camera it is set up at the factory and normally requires no adjustments Sometimes however adjustments may be necessary 1 Remove the dome and trim ring using the supplied 1 8 inch hollow screwdriver bit 2 Adjust the vertical phase iris level focus or switc
14. tch 1 For gamma correction Switch to accurately reproduce scene brightness when turned on y 7 0 6 and when turned off 1 0 For gain control Switch 3 On increases gain by 6 dB and switch 3 Off increases gain by 18 dB SPECIFICATIONS General Operating Temperature 50 to 122 F 46 to 50 C De ices to 25 F 4 C Cable Entry 3 4 inch 1 91 cm conduit fitting and 3 4 inch 1 91 cm opening for NPT threaded pipe Pan Tilt Adjustment Manual 360 pan 180 tilt Construction Aluminum with steel camera mounting bracket and poly carbonate dome Finish Gray polyester powder coat Dimensions Base 3 70 H x 5 30 W inches 9 40 x 13 50 cm Bubble 3 75 inch diameter Environment Low temperature indoor outdoor Unit Weight 2 20 Ib 1 00 kg 10 Pelco Manual C2407M G 5 03 To enable auto iris and manually set shutter speed Turn off switch 7 set switches 4 5 and 6 for the desired shutter speed CAUTION Do not change the shutter speed unless you understand how changing the settings will affect the scene detail Shutter Switch Number and Position Speed 7 6 5 4 1 60 NTSC 1 50 PAL on on 1 100 Off On On 1 250 of On Off On 1 500 Off Off On 1 1000 On On Off 1 2000 ott On oft 1 4000 On Off oft 1 10000 Off Off Off Electrical Input Voltage 12 VDC or 24 VAC 10 Power Consumption 13 watts or less Video Connector BNC Certi
15. the heater board 1 Disconnect the four pin heater wiring 2 Wait for the heater elements to cool if they are hot 3 Apply pressure and press on the corner of the board FOCUS To adjust the focus ADJUSTMENT SCREW Loosen the locking screw on the bottom of the lens Move the screw in the slot to bring the picture into focus Retighten the locking screw Replace the heater board if it was removed Reconnect the four pin heater wiring BOTTOM VIEW OF CAMERA WITH HEATER BOARD REMOVED 8 Pelco Manual C2407M G 5 03 Switch Settings for Fixed Focal Length Lens with Auto Iris Refer to the switch drawing The switch is located next to the lens Automatic backlight compensation factory setting is used under varying lighting conditions such as outdoors or fixed lighting conditions Where there are no bright spots that darken other picture details Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots ALC ELC switch Always ALC FACTORY SETTINGS oa sal YIDC switch Always DC ed a o i ON Auto backlight compensation switch OFF I n ABL switch ON OFF O 2555 Manual backlight compensation BLC switch ON ABL switch OFF E SWITCH POSITION Switch Settings for Fixed Focal Length Lens Without Auto Iris Refer to the switch drawing The switch is located next to the lens Automatic backl
Download Pdf Manuals
Related Search