Home

Peavey DECA 724 User's Manual

image

Contents

1. Open 911 m Sy Closed On Factory Settin Si a ee S7 5 5 87 S8 s S6 SB These high pass fillers are internaland accessible only by removing the chassis cover Any adjustment of the filter setting s must be done by an Authorized Peavey Dealer or Authorized Peavoy Service Center The 40 Hz filter is recommended for most two or three way sound reinforcement systems as this eliminates stage rumble and other subsonic material which can damage loudspeakers Power amplifier headroom is also conserved when the 40 Hz filter is engaged acre DECA 724 THERMAL DIGITAL ENERGY CONVERSION AMPUFIER ad sau FRONT PANEL 1 10 Channel A and Channel B Input Sensitivity Control The input sensitivity controls for each channel act asa master volume control permitting edjustment of the overall system gain to minimize hum and noise and still provide adequate headroom The numbered dial indicates the sensitivity in volts necessary to attain full power with the contro in that position In the full clockwise position the relative sensitivity is approximately 1 0 volts RMS or 0 dBV for full output power 2 9 The LED array indicators provide a visual display of the output power of the individual amplifiers in both percent of total power and available headroom The bottom LED of each array will remain lit when AC power is applied to the amplifier and the amplifier is operating in the stereo mode This will serve as a Power On indicator for
2. RATED POWER OUTPUT 350 Watte RMS per channel into 4 ohms with less Inar Ma Totat Harmoni Distortion Both channels inven 450 Watts RMS per channel into 4 ohms with less thang 98 rot Harmonie Distortion Boin chamnal 700 Watts RMS into 0 ohms In bridge mode TOTAL HARMONIC DISTORTION Less than 0 1 lypicaliy bolow 0 06 THO 350 watis AMS per cnannel nto 4 ohms Less than 0 3 450 watts RMS per channel into 4 ohms TRANSIENT INTERMODULATION DISTORTION None Present 0 TIM OUTPUT SLEW RATE The amplifier output Siew rate is internally con trolled e optimize phase linearity and improve trar sient response Due to the nature of Ie ampiner Gesign anc the internal signal conditioning circuitry 10V AMS for 350 watts into 4 ohms LOAD PROTECTION Relay protected ai each output with instantaneous tum off and 4 second Turn om delay to prevent Unwanted system transients Complets digital con iro shut down activation tor both amplifier protec tion and positive speaker protection THERMAL Incependent automatic thermal channel shutdown with front panel indicators LOAD IMPEDANCE 4 ohms or greater unconditionally stable into any load contiguration or any signal condition anc level a he input FRONT PANEL INDICATORS 30 segment LED arrays indicating standby status and percent power output level EDT LED activation indicators Thermal Fauli LED activation indicators QuiputL ine Faut LED macators sor ozu DC ee POW
3. itom lo any AUTHORIZED PEAVEY DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product It the DEALER or SERVICE CENTER is unablo to provide the necessary warranty service you will ba directed to the nearest other PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provice such service oR b Ship the defective Item prepaid to FEAVEY ELECTRONICS CORPORATION international Service Center Highway 80 East MERIDIAN MS 39301 including therewith a complete detailed description of the problem together with a legible copy of the original PROOF OF PURCHASE anda complete roturn addross Upon Peavoy s receipt of these items Tr tno datos le remedial under these limited warranties and the other terms and conditions expressed herein have been complied with Peevey will provide the necessary warranty service to repair or replace the product and will return it FREIGHT COLLECT to you the purchaser Peavey liability to the purchaser tor damages from any cause whatsoever and regardiess ofthe form of action including negligence is limited to the actual damages up to the areater a 500 00 or an amount equal io the purchase price of he produet that caused the damage or that is the subject of or is directly related to the cause of action Such purchase Bree will be thet in effect for tho specific product
4. the unit When the amplifier is switched to Bridge Mode on the rear panel the Channel B LED will no longer be lit indicating that the operative control is now Channel A 3 6 The DDT active indicators provide a visual display of the compression operation As long as gain reduction is occurring the LED will continue to light thereby giving a valuable indication of this unique compression function The DDT compression may be defeated on each channel separately with the DDT defeat switch 7 8 on the rear panel When the DDT compression is defeated the front panel DDT indicator will no longer light indicating that the DDT compression is no longer working Care should be taken when this condition exists since the amplifier can now be severely overdriven and much higher levels of power are available at the output jacks This condition could be harmful to speaker systems 4 7 The Thermal Fault indicators provide a visual display of any interruption in operation due to thermal overload and should a single channel overload thermally the other channel will continue to function normally 5 8 The Line Fault indicators provide a visual display of any temporary interruption in each channel due to an output line fault e g short circuit DC voltage transient suppression over current The Line Fault indicators for each channel are independent and will remain litas long as the fault exists The fault protection circuitry will automatically restart approxim
5. ER CONSUMPTION 800 walls 120 VAG 50 60 Hz domestic model cannot slew rate imit DDT Disabled measured at 1 kHz CLASS B COMPUTING DEVICE INFORMATION TO USER This equipment generates and uses radio frequency energy and if not installed and used properly that is in accordance with the manufacturer s instructions may cause interference to radio and television reception It nas been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on tho user is encouraged to try to correct the interference by one or more of the following measures reorient the receiving antenna e relocate the equipment with respect to the receiver move the equipment away from the receiver e plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identi
6. L EXPORTED PRODUCTS ARE SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY Ces clauses de garantie ne sontvalables qu aux Etats Unis et au Canada Dans tousles autres pays los clausos de garantie et de maintenance sont fixees parle distributeur national et assuree par lul selon la legislation on vigueur Diese Garantie ist nurin den USA and Kanada gultig Alle Export Produkte sind der Garanile und dem Service des Importeurs des jewelligen Landes unterworton Esta garantia esvalida solamente cuando el producto es comprado en E U continentales o en Canada Todos los productos que sean comprados en el extranjero estan sujetos alas garantias y servicio que cada distribuidor autorizado determine y ofrezca on los diferentes paises ONE YEAR LIMITED WARRANTY REMEDY PEAVEY ELECTRONICS CORPORATION PEAVEY warrants this product EXCEPT for covers footswitches patchcords tubes and meters to be tree from detects in material ard workmanship fora periodo one 1 year from date of purchase PROVIDEO however that this limited werranty is extended only to the original retail purchesor and is subject tothe conditions exclusions anc limitations hereinafter set forth PEAVEY 90 DAY LIMITED WARRANTY ON TUBES AND METERS ifthis product contains tubes or molore Poavay warrants the tubas ot meters containedin thaproduct tobe tree from defects in material ana workmanship fora period of ninety 90 days I
7. OWNERS MANUAL FACE DECA 724 WARNING TO PREVENT ELECTRICAL SHOCK OR FIRE HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE BEFORE USING THIS APPLIANCE READ THE OPERATING GUIDE FOR FURTHER WARNINGS GENERAL DESCRIPTION The DECA 724 provides an innovative approach to audio amplification by utilizing next generation Digital Energy Conversion technology the result of a dedicated effort to merge the advantages of high speed digital computer electronics high efficiency semiconductor devices and electro magnetic energy conversion technology The amplifier system has been designed for commercial duty amplification where performance reliability and long life are foremost requirements Professional design specifications and in process quality checks combine to produce an amplifier with outstanding performance at a reasonable price This compact powerful system features a digital version of Peavey s DDT Distortion Detection Technique compression circuitry that electronically senses increased distortion levels well in advance of clipping and engages a specially designed circuit which virtually eliminates the possibility of driving the amplifier into distortion beyond approximately 1 0 THD This DDT compression circuit may be disengaged on each channel independently if desired via the slide switches on the rear panel The DECA 724 amplifier isa highly efficient approximately 90 at all output levels power transfer syste
8. RANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THESE LIMITED WARRANTIES ARE THE ONLY EXPRESS WARRANTIES ON THIS PRODUCT AND NO OTHER STATEMENT REFHESENTATION WARRANTY OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY inthe eventof any modificationor disclaimer o express or implied warranties or any Imitation of romodios contained herein conflicts with applicable law then such modification disclaimer or limitation as the case may be shall be docmed to be modified to the extent necessary to comply with such law Your remedies lor breach of Inese warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warrenty only with respoct to equipment purchased in tne United States of America INSTRUCTIONS WARRANTY REGISTRATION CARD 5 Mail the completed WARRANTY REGISTRATION CARD to PEAVEY ELECTRONICS CORPORATION POST OFFICE BOX 2696 MERIDIAN MISSISSIPPI 39802 2603 e Keep the PROOF OF PURCHASE In the event warranty service is required during the warranty period you will need this document There will be no identification card issued by Peavay Electronics Corporation 2 IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESS a Completion and mailing of WARRANTY REGISTRATION CARDS Should notification become necessary for any condition trat may require correction the REGISTRA
9. TION CARD will help ensure that you are contacted and properly notifies b Notice of address changes you move from the address shown on the WARRANTY REGISTRATION CARD you should notify Peavey of the change of address so as to facilitata your receipt of any Bulletins or other forms et notification which may become necessary in connection with any condition that may require dissemination of information or correction 3 You may contact Peavey directly by telephoning 601 483 5368 4 Pleas have the Peavey product name and serial number available when communicating with Peavey Customer Service BEY Features and specifications are subject to change without notice PEAVEY ELECTRONICS CORPORATION 711 A Street Meridian MS 39301 U S A Telephone 601 483 5365 Telex 504115 81989 Printed in U S A 480301007 REV 01 89
10. as the output and the signal source should be driven into the Channel A input Dueto the high currents at full output itis recommended thatNo 16 or larger wire be used whenever possible Smaller wire sizes will waste power and yield less than optimum performance It is also suggested that in commercial and other non portable applications the binding posts 1 12 be used instead of the Y phone jacks The binding posts are an industry standard and mating banana plugs are available from most electronic distributors As with all electronic equipment proper phasing of the outputs is important A little time spent in correctly identifying the wiring could alleviate a lot of problems in the field INPUT SECTION All input connections are made at the rear panel jacks Shielded cables should be used to minimize hum and noise pickup The nominal input impedance is 15K ohms compatible with home stereo devices The DECA 724 has an input sensitivity of 1 0 volts RMS or 0 dBV for rated output with the input sensitivity controls set at 0 dBV This sensitivity decreases as the control is turned counterclockwise CCW All inputs on the DECA 724 feature automatic signal ground lift capability This minimizes the possibility of system ground loop hum by automatically lifting the input signal ground from chassis ground whenever hum causing conditions are present 8 11 The Balanced Input XLR connectors provide an electronically balanced input capability for tru
11. ately four seconds after the fault is cleared It should be noted that since the amplifier protects against any turn on transients the Line Fault indicators will remain lit for approximately four seconds after AC power is applied to the amplifier Atthis time the Line Fault condition will be cleared and the line outputs will be enabled 11 The On Off Switch is located on the front panel and is used to apply the AC mains power to the unit When the amplifier is plugged into a suitable power source activating this switch should light the lower LEDs on each channel s LED arrays Failure of the LEDs to light may indicate the line fuse is blown or the power source is faulty Wesen EM CHANNEL A auraurs SEMEN Eo REAR PANEL OUTPUT SECTION Two types of output connections are provided on the rear panel of the power amplifier modules The Binding Post outputs 1 12 of each channel of the amplifier are connected in parallel with the two Phone Jack outputs 2 13 of each channel of the amplifier The minimum suggested load for the total parallel combination for each channel is 4 ohms Care should be taken when lower impedance loads are used due to increased power demand placed on the amplifier The amplifier is capable of delivering in excess of 350 watts RMS from each of these channel modules into 4 ohms When operating in Bridge Mode the red binding post of each channel should be used
12. fy and Resolve Radio TV Interference Problems This booklet is available from the US Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 DANGER EXPCBURE TO EXTAEWELY HIGH NOISE LEVELS MAY CAUSE A PERMANENT HEARING LOSS INDIVIDUALS VARY CONSIDERABLY IN SUSCEPTIBILITY TO NOISE INDUGED NEARING LOSS BUT E TC ENE mui Lose SOME HEARING IF EXPOSED 10 SUFFICIENTLY INTENSE NOISE FOR A SUFFICIENT TIME Je US GOVERNMENT S OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION OSHA HAS SPECIFIED THE FOLLOWING PERMISSIBLE NOISE LEVEL EXPOSLFES DURATION PER DAY IN HOURS SOUND CeveL daa SLOW RESPONSE a mu e shen ks BEEN DESGUECA AEN x w A 3 T fete eee A ED ni rane mure wormaben en oreuraing wre lr Our fee Scb 14 Daey pi emon ine e Se tte me rtr e Sie wait tr pace sanan an power supply ieh BEN onde eos tores pr siars es ray amp Tus product oud be located sorai ia postionciesn r Oaea aM o dea SA wnen TE UNS dc E Gi paet nat o ng ia Seri clon sre cn se Sens vita domo 0 AN fran amona baste Hausen elearen 1 ECOS nsum ouap saene oys auntie etia A The power suppl ser or lug tas been amago 5 Tre cr har bean dropped or Im enclose damaged MO Tre ur shoul vct atemat te sartor tha eaupmert AN Aper The DEGA 724 is manvfactured under U S patent 4 318 053 and five patents pending THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA AL
13. ional power amplifiers on the market on a dollar per watt performance basis Professional specifications components the latest semiconductors and contemporary design make the DECA 724 the obvious choice for demanding commercial professional applications Comparison of performance features construction techniques and quality of components with any of its competition will illustrate the excellence of this professional amplifier The new DECA 724 system is a stereo Digital Energy Conversion unit capable of high efficiency energy transfer to various speaker load configurations with professional performance specifications The Energy Conversion system is rated at 350 watts RMS per channel both channels driven into a 4 ohm load with less than 0 196 THD and features a modified version of Peavey s patented DDT compression circuitry to minimize distortion due to clipping at the maximum energy transfer levels Due to the nature of the design of the amplifier system no transient intermodulation distortion can be introduced by the unit even with very complex signals and at high signal levels INSTALLATION AND CONNECTION The Peavey DECA 724 digital energy conversion amplifier is designed tor durability in commercial installations and high quality performance in studio and home applications The DECA 724 is a dual channel power amplifier with each channel capable of delivering more than 350 watts RMS into a 4 ohm load The amplifier is of the standard 19 rack mo
14. little care will insure long and reliable operation Most applications allow the amplifier to be mounted in any configuration and require no special considerations for abnormal thermal situations However an inadvertent short circuit or sustained high power usage could cause the internal thermal protection circuitry to engage This situation is indicated by the front panel thermal fault indicators Allinput and output connections are made at the rear panel jacks A discussion of the purpose and use of each of the rear panel jacks is provided in the Rear Pane Operation section of the manual OPERATION The DECA 724 Digital Energy Conversion Amplifier is designed for maximum ease and flexibility of operation When the unitis installed and connected as described in this manual operation is simply turning on the main switch and setting the front panel sensitivity controls for the desired output level or until the front panel LED array indicates that the amplifier is delivering the desired amount of power The DDT compression system enables the user to maximize the performance of tho amplifier speaker combination Years of experience and research have determined compression circuitry should prevent the power amplifier from running out of headroom clipping and should be as simple to operate as possible to avoid undue complication for the user The compression system senses conditions which indicate increased distortion well in advance of clipping and acti
15. ly differential input signals 4 10 The Unbalanced Input Phone Jack connectors provide a single ended input when balanced inputis not required For ease of use however the unbalanced input is implemented with a stereo phone jack so that it can also be used for the balanced input In this configuration the tip of the phone jack is the positive in phase input and the ring is the negative input Note To minimize any grounding problems always use Balanced inputs either with the XLR connectors or the stereo phone jacks 5 9 The Line Out connector is provided tor ease in connecting several amplifiers in parallel without the use of Y type connections Note If a balanced input configuration is being used a stereo phone jack should also be used in the Line Out connection to maintain the balanced configuration In this case the tip is the positive in phase signa and the ring is thenegative signal To minimize any problems due to grounding it may be desirable to connect the shield of the shielded cable only on the destination end 6 B side only The Mode Switch is provided to select either Stereo Mode or Bridge Mode operation Under normal operating conditions the Mode Switch should be in the Stereo position Unless the amplifier is to be used in a commercial sound distribution system 70 volt line the bridge mode should not be used When in Bridge Mode the Red binding posts on either side should be used as outputs the Channel A inputs should be u
16. m capable of delivering up to 350 watts RMS per channel continuously to a 4 ohm load without the use of massive heat sinks to insure low operating temperatures in any given environment In the event of abnormal load conditions or inadvertent misuse the system is equipped with complete and independent thermal short circuit and overload protection against amplifier system failure In addition the DECA 724 has built in protection circuitry in each channel to instantaneously sense any hazardous output conditions which might harm speaker systems The advent of abnormal DC voltages on the output terminals engages specia output protection circuitry which disconnects the channel output from the speaker load until the fault is corrected All thermal short circuit and output line faults have corresponding LED indicators on the front panel Asa home hi fi amplifier the Peavey DECA 724 is an unmatched stereo power amp However a word of warning should be given concerning the choice of the speaker system used A true 350 watts per channel can easily overpower many home loudspeaker systems The operation of the DECA 724is essentially straightforward and will present no difficulties in most applications Our exclusive DDT compression circuitry enables the total system to enjoy freedom from most of the commonly encountered headroom problems with power amplifiers The DECA 724 is another step in the continuing struggle to provide one of the most competitive profess
17. rom date of purchase PROVIDED however that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions exclusions and limitations hereinafter set orth CONDITIONS EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall bo void and of no effect if a The first purchase of the product is for tne purpose of resale or b The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER or The product has boen damaged by accident or unreasonable usa neglect Improper service or maintenance or other causes not arising out of defects in material or workmanship or d The serial number affixed to the product is altered defaced or removed In the event of a defect in material and or workmanship covered by this limited warranty Peavey will a In the case cf tubes or meters replace the defective component without charge b In other covered eases Le casos involving anything othar than covers cotswitches patcheords tubes or meters repair the defect in material or workmanship or replace the product al Peavey s option and provided however thai in any case all costs of shipping if necessary are paid by you tho purchaser THE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN 14 DAYS FROMTHE DATE OF YOUR PURCHASE In order to obtain service under these warranties you must a Bring the defective
18. tilized and the Channel A Input Sensitivity control is the active control It should be pointed out that for proper operation both wires of the output must float above ground 7 8 The DDT Compression Defeat Switch is utilized to disengage the DDT compression on each channel separately It should be noted that with DDT disengaged the power output can exceed 350 watts per channel at a slightly higher distortion 14 The DECA 724 Power Connector is a heavy duty IEC type with a conventional AC plug with a ground pin It should be connected to a circuit capable of at least 15 amps continuous or greater If the socket used does not have a ground pin a conventional adapter should be used and the third wire grounded properly Never break off the ground pin on a line cord of the DECA 724 The use of extension cords should be avoided but if necessary always use a three wire type with at least a No 16 wire size The DECA 724 is fused with a standard 10 amp fuse 15 Always replace with the same type and rating Failure to do this could void the warranty SPECIFICATIONS FREQUENCY RESPONSE HUM amp NOISE DIMENSIONS 10 Hz to 20 Hz 0 1 dB 350 watts into 4 ohms Greater than 95 GB below full power 20 Hz V WSS HX 3 dB 40 KHz 350 Watts into 4 ohms limited by kHz E y a ae Bestel nou er WEIGHT INPUT SENSITIVITY 33 bs INSTANTANEOUS AVAILABLE POWER Headroom 350 waits RMS per channel nto 8 ohms 550 waits AMS per channel into 4 ohms
19. unt configuration and requires forced air cooling to alleviate any abnormal thermal conditions Where sustained high power operation is required the amplifiers should be mounted ina standard 19 rack with one rack space 1 between each amplifier in the stack The thermal protection for the power amplifier modules is engaged when inadvertent sustained high power usage endangers the output modules Activation of this thermal protection is indicated by the thermal fault LED on the front panel This fault is not fatal nowever and the amplifier is self restarting in thermal condition It should be noted that the fan pulls air from the rear bottom and sides of the amplifier and exhausts the hot air through the front It is for this reason that one rack space should be left between the units and an adequate air supply must be provided for the amplifiers The internal fan must have a source of air that is not preheated by other equipment If cooling is inadequate due to the low speed fan operation preheated air or reduction of air flow the internal thermal breaker may cause temporary shut down of the amplifier Note Under no circumstances should the amplifier be operated while sitting on a flat surface without the supplied rubber feet since the amplifier requires proper ventilation for cooling As a general rule the cooler electronic equipment is operated the longer its useful service life You have invested in the finest equipment that money can buy anda
20. vate compression to prevent system overload This unique implementation provides for the optimum power output with minimal distortion and with an increased dynamic headroom Because of the dynamics of music and vocals it is quite common to activate the compression circuitry virtually constantly during a performance since this is what it is designed to do i e to maximize the dynamics available from the amplifier within its power output capabilities regardless of power supply line voltage variations and load impedance selection NOTE In applications where extreme low frequency signal content degrades the performance of the sound system precautions should be considered to eliminate these subsonic frequency components Applications which fall into this category include Horn Loaded Speaker Enclosures Tiansformer Coupled Distributed Sound Systems Auto Transformer Matohed Systems High Efficiency Extended Range Systems Complex Crossover Systems The DECA Series amplifiers have been provided with a selectable subsonic low frequency roll off high pass filter on each of the DECA power modules The roll off frequencies can be selected internally via Dip Switch SW1 located on each Control Interface P C Board The filter roll off frequencies can be chosen as follows 10Hz 40 Hz 60 Hz 100 Hz E on ON On 2 1 1 T 3 E 3 i 4 a a 4 5 5 5 A 8 H B 7 7 7 5 H 5 3 B AII Switches Close Open Close Open All Switches
21. when the cause o action arose This limitation af liability will not apply 10 claims for personal injury or damage to real property or eng ble personal property allegeciy caused by Peavey s negligence Peavey does not assume liability for personal injury or property damage arising out of or caused by a non Peavey Aeration or atiechment nor does Peavey assume any responsibility for damage to interconnected non Peavey equipment that may result from the normal functioning and maintenance of the Peavey equipment UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS LOST SAVINGS ANY INCIDENTAL DAMAGES OR ANY CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE PROVIDED HOWEVER THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO THE EXISTENCE OF THE EXPRESS LIMITED WARRANTIES AS HEREINABOVE STATED HAVE BEEN COMPLIED WITH IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE YEAR OR NINETY DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT SOME STATES DO NOT ALLOWLIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THESE LIMITED WAR

Download Pdf Manuals

image

Related Search

Related Contents

KitchenAid KURO24LSBX Refrigerator User Manual  プレス リリース  Samsung YP-T9BAB User Manual  iOptron SMARTSTAR IEQ75-GTTM User's Manual  INSTRUCTION GUIDE  XM-GTR7040  Epson MovieMate 72  

Copyright © All rights reserved.
Failed to retrieve file