Patton electronic 571 User's Manual
Contents
1. Connection to An chassis ground Figure 3 Installation of Model 571 581 Surge Protectors 3 Locate a metal chassis ground on the equipment to be protected This is often a hex screw on a D shell or AUI connector Sometimes a metal back panel is attached by screws one of which can be used for chassis grounding If you cannot locate a chassis ground connection on your equipment contact Patton Technical Support at 301 975 1007 http www patton com or support Opatton com Connect the braided ground strap directly to the chassis ground connection you have located see Figure 3 above Caution Surge energy may run both directions on the ground strap To provide the best protection it is essential that the ground strap on the Model 571 581 be connected to the chassis ground of the protected device Do not lengthen the ground strap of the Model 571 581 or connect to a ground other than chassis ground unless instructed to do so by Patton Technical Support Connection of the Model 581 at a Barrier Wall Bldg Entrance etc 1 2 Disconnect the UTP cable from the wall jack or patch panel jack Install the Model 581 between the UTP line and the jack This installation requires a straight through Cat 5 patch cable with modular RJ 45 connectors supplied with unit Note The Model 571 581 provides bi directional clamping protection Therefore2. ISO 24 An ISO 9001 Certified Company Part 07M571 581 A Doc 074300UA Revised 1 9 97 USER MANUAL MODEL 571 581 100Base T CAT 5 Surge Protectors 28 PATTON HJ Zlecironics To SALES OFFICE 301 975 1000 TECHNICAL SUPPORT 301 975 1007 http www patton com 1 0 WARRANTY INFORMATION Patton Electronics warrants all Model 571 581 components to be free from defects and will at our option repair or replace the product should it fail within one year from the first date of shipment This warranty is limited to defects in workmanship or materials and does not cover customer damage abuse or unauthorized modification If this product fails or does not perform as warranted your sole recourse shall be repair or replacement as described above Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product These damages include but are not limited to the following lost profits lost savings and incidental or consequential damages arising from the use of or inability to use this product Patton Electronics specifically disclaims all other warranties expressed or implied and the installation or use of this product shall be deemed an acceptance of these terms by the user 1 1 SERVICE All warranty and nonwarranty repairs must be returned freight prepaid and insured to Patton Electronics All returns must have a Return Materials Authorization number on th
3. the network and equipment cables may be connected to either end Locate an electrical ground nearest the jack Often this will be on an electrical panel or subpanel If you cannot locate a nearby electrical ground contact Patton Technical Support at 301 975 1007 http www patton com or support patton com to discuss an alternative grounding solution Connect the braided ground strap directly to the electrical ground you have located The best way to make this connection is to attach the braided metal strap to a metal panel or wallplate screw using a hex nut or screw Caution Surge energy may run both directions on the ground strap To provide the best protection it is essential that the ground strap on the Model 581 be connected to an electrical ground APPENDIX A MODEL 571 581 SPECIFICATIONS Environment Connectors Response Time Characteristic Impedance NEXT Loss Surge Clamp Voltage Surge Rating DC Clamp Voltage Insertion Loss Return Loss Group Delay Series Resistance Grounding Dimensions Category 5 Interfaces that utilize the RJ 45 connector including RS 422 423 10Base T Token Ring Fast Ethernet 100Base T and ATM on a 4 wire interface RJ 45 Female Clamped to 13 V after 0 1 us 100 Ohms Model 571 worst pair Better than 45 dB at 100 MHz Model 581 worst pair Better than 43 dB at100 MHz Model 571 13 V max with 1 KV Input Model 581 15 V max with 2 KV Inpu
4. 40 48 43 23 16 26 36 41 48 23 20 25 34 38 39 23 25 24 30 34 25 14 31 25 22 27 28 29 14 62 50 20 19 19 18 14 inn 17 22 10 12 1A 100 23 9 14 E Table 4B Patton Model 581 Ratwn T no Mong Return Loss Meas meen owe pine BING pine DEA PRO FIN FINS FIN FIND NEELU Mhz 1 2 3 6 45 7 8 B AR n An sr ab an ab a ES 1 27 29 29 28 23 4 34 36 33 37 23 8 32 42 47 43 23 id 30 43 48 47 23 16 26 41 41 48 23 20 24 39 38 40 23 25 24 33 33 34 14 3125 22 27 29 29 id 62 50 20 21 19 19 14 100 i6 25 Zi i8 id Copyright O Patton Electronics Company All Rights Reserved 11 Dear Valued Customer Thank you for purchasing Patton Electronics products We do appreciate your business I trust that you find this user manual helpful We manufacture one of the widest selections of data communications products in the world including CSU DSU s network termination units powered and self powered short range modems fiber optic modems interface converters baluns electronic data switches data line surge protectors multiplexers transceivers hubs print servers and much more We produce these products at our Gaithersburg MD USA facility and can custom manufacture products for your unique needs We would like to hear from you Please contact us in any of the following ways to tell us how you like this product and how we can meet your product needs today and in the future Web http www patton com Sales E mail sales patto
5. ING RESULTS TYPICAL NEAR END CROSSTALK MEASUREMENT F 1 Table 3A NEXT Measurements Model 571 FREQ 1 2 1 2 3 6 3 6 45 Mhz 45 7 8 45 7 8 7 8 dB dB dB dB dB 1 TF 76 86 85 80 80 gt 65 4 TA 69 84 81 7 7 5 8 65 63 78 82 66 65 62 10 64 6l 80 76 62 64 60 16 60 58 79 75 59 i 56 59 56 76 76 58 59 54 57 54 76 71 55 57 52 55 51 74 70 53 57 50 53 45 64 60 46 51 44 54 Al 56 AQ 42 49 40 L las ail kraan kh ol al sd Tahlia 2D NEWT Wane nrn anho NAnAal 21 LAW ILI INE Za 1 LVNTADUL CHICH U WIAA JOL EA Th a 12 2A FPT PEET PREW 1 2 i Gl s gt Of J i F DFEL Mhz 3 6 45 7 8 45 7 8 7 8 AR im AR AR AR AR ab apn ab apn ab apn l 77 76 85 85 81 81 gt 65 4 70 68 84 83 70 71 gt 65 65 63 17 83 65 65 62 63 i 18 79 i 64 60 60 58 TI 78 58 6l 56 58 56 75 15 56 59 54 57 54 74 73 54 56 52 55 52 74 70 52 55 50 52 45 64 60 45 51 44 54 i 55 48 l 49 40 10 TSB 40A COMPLIANCE TESTING RESULTS TYPICAL RETURN LOSS MEASUREMENT APPENDIX B Continued morr AA attan AE Aa STI Lape 4A WOM IVIOGGEL D L Return Loss Measurements FREQ PINS PINS PINS PINS SPE Mhz 1 2 3 6 45 7 8 C dB dB dB dB dB 1 28 29 29 27 23 4 34 37 37 37 23 8 31 40 44 44 23 10 30
6. barrier application for the Patton Model 581 The Model 581 is also well suited for use in severe lightning areas heavy industrial environments and installations with heavy machinery in the direct vicinity of sensitive LAN eguipment and cabling Figure 2 above shows a typical application for the Model 581 For best results the braided grounding strap on the Model 581 should be attached to the grounded metal frame of the device being protected When installation is made at a barrier such as an external wall the braided strap should be connected to a nearby electrical ground 3 2 INSTALLATION PROCEDURES In order to operate as designed the Model 571 and 581 must be connected correctly to your Cat 5 network Please read all the instructions below and follow them carefully Connection of the Model 571 or 581 to an I O Port 1 Turn off eguipment power and unplug disconnect the existing connection between the UTP cable and the eguipment s I O port Install the Model 571 581 between the incoming UTP line and the protected equipment see Figure 3 below This installation requires a straight through Cat 5 patch cable with modular RJ 45 connectors supplied with unit Note The Model 571 581 provides bi directional clamping protection Therefore the network and equipment cables may be connected to either end Cat 5 patch cable to protected equipment 6 inches or less Cat 5 input from network ra Gee
7. damage The Patton Model 571 and 581 Series Surge Protectors provide effective surge protection for devices operating in Category 5 Cabling Systems The Model 571 is specifically designed for point of use installation the Model 581 is designed to be installed at the building entrance Both models use a multi stage Silicon Avalanche Diode circuit and will continue functioning while handling the appropriate IEC 801 5 surges applicable to their use see the tables in Appendix B Both the 571 and 581 will additionally protect against surges up to and exceeding 2kV 1kA in fail safe mode Models 571 and 581 support a wide range of balanced interfaces running over 4 wires Highlights include a low insertion loss less than 0 4dB at 100MHz and minimal near end cross talk greater than 43 dB at all frequencies up to 100 MHz Grounding is accomplished via an external ground strap that provides a separate unit ground to chassis ground connection Warning This product will not provide complete protection should your equipment or building be subject to a direct lightning hit 3 0 INSTALLATION Patton s Model 571 and 581 surge protectors are easy to install and are designed to operate transparently to your network This section describes connection procedures for both models 3 1 PRODUCT APPLICATIONS Both Models 571 and 581 protect 4 pins on the modular RJ 45 Cat 5 interface and work in environments with data rates up to 100 Mbps The follow
8. e outside of the shipping container This number may be obtained from Patton Electronics Technical Support 301 975 1007 http www patton com or support patton com Notice Packages received without an RMA number will not be accepted Patton Electronics technical staff is also available to answer any questions that might arise concerning the installation or use of your Model 571 581 Technical Service hours 8AM to 5PM EST Monday through Friday 2 0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product This product has been thoroughly inspected and tested and is warranted for One Year parts and labor If any questions or problems arise during installation or use of this product please do not hesitate to contact Patton Electronics Customer Service at 301 975 1007 2 1 FEATURES e Multi level surge protection e Operation at Speeds up to 100 Mbps e Four wire protection on lines 1 2 3 and 6 on Cat 5 RJ 45 e EIA TIA TSB 40A Category 5 Compliant e N E X T better than 43 dB at 100 MHz e Shunts surges directly to chassis ground e Easy to install e Made in the U S A 2 2 DESCRIPTION Devices that connect to Category 5 cabling systems are routinely threatened by unwanted electrical energy lightning AC power induction ESD and more Higher speed devices such as those operating at 100 Mbps are especially vulnerable to the effects of these hazards which can include data loss and hardware
9. ing descriptions will give you a general guideline for installing the units in your Cat 5 environment 3 1 1 POINT OF USE APPLICATION MODEL 571 The Model 571 is designed for installation on LAN equipment in a typical office environment see Figure 1 below For best results the Model 571 should be connected as close as possible to the communication port of the device to be protected Also the flat braided grounding wire on the Model 571 should be attached to the grounded metal frame of the device being protected So Model 571 Model 571 m ye Ne E Figure 1 A typical Point of Use Application for the Patton Model 571 3 1 2 BARRIER APPLICATION MODEL 581 The Model 581 is a more robust protector than the Model 571 and is designed for use as a barrier protector on LAN equipment in campus networks Applications include cable runs between buildings cable runs between floors on multi story structures and as a higher capacity replacement for the Model 571 Model 571 or 581 aen a A Electrical Panel Exterior Wall a 3 07 KA To other bldg or Model 571 or 581 Local Hub floor n mMm r A N HTT N Model 581 Model 571 or 581 Figure 2 A typical
10. n com Support E mail support Opatton com Phone Sales 301 975 1000 Phone Support 301 975 1007 Fax 301 869 9293 Mail Patton Electronics Company 7622 Rickenbacker Drive Gaithersburg MD 20879 USA We are committed to a guality product at a guality price Patton Electronics is BABT and ISO 9001 certified We meet and exceed the highest standards in the industry CE UL etc It is our business to serve you If you are not satisfied with any aspect of this product or the service provided from Patton Electronics or its distributors please let us know Thank you Burton A Patton Vice President P S Please tell us where you purchased this product 12
11. one not including the standard 6 inch 15 25 patch cable that is shipped with the unit IEC 801 5 Threat Levels as a Function of Class Class Sym Lines Coupling Mode Line GND Zs 42 Ohms 1 1 0 kV 24A 2 1 0 kV 24A 3 2 0 kV 48A 4 n a n a 5 4 0 Kv 95A Wave 1 2 x 50 us Forms 1 2 x 50 us Table 1 IEC Threat Levels as a Function of Class APPENDIX B EIA TIA TSB 40A COMPLIANCE The Model 571 81 series surge protectors have been designed to conform to stringent EIA TIA TSB 40 standards as reguired for all Category 5 connecting hardware These standards specify the capacitance and near end cross talk N E X T to insure proper operation of ALL connected eguipment Specific test results are shown in the tables on the following pages F 1 Table 2A Patton Model 571 Attenuation Measurements FREQ PINS PINS PINS PINS SPEC Mhz 1 2 3 6 45 7 8 dB dB aB aB aB 1 0 1 0 1 0 1 0 1 0 1 4 0 0 0 0 0 0 0 0 0 1 8 0 0 0 0 0 0 0 0 0 1 10 Ol Oi 0 1 Gl 0 1 16 0 2 0 1 0 1 0 0 0 2 20 0 0 0 0 0 0 0 0 0 2 25 0 1 0 0 00 0 0 0 2 31 25 Ol 0 0 0 0 0 0 0 2 62 50 0 1 0 1 0 1 0 1 0 3 100 0 4 0 2 Ol Ol 0 4 Note All test results are for the Model 571 581 alone not including the standard 6 15 25cm patch cable that is shipped with the unit APPENDIX B Continued EIA TIA TSB 40A COMPLIANCE TSB 40A COMPLIANCE TEST
12. t IEC 801 5 Standard Level Common Mode to Gnd each line7 5 V 50 mA Differential mode per pair 8 1 V 50 mA Less than 0 4 dB at 100 MHz including connector Better than 14 dB None 1 MHz to 100 MHz Less than 400 millionms External ground strap provides separate unit ground to chassis ground contact 2 0L x 1 0 D APPENDIX B MODEL 571 581 INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC COMPLIANCE Meets IEC standards 801 2 801 4 and 801 5 CE Mark Effective January 1996 the European Economic Community will require that all electronic devices be tested and comply with all applicable International standards relating to the product type and category of use Electromagnetic Compatibility Directive 89 336 EEC specifically addresses communication line surge protection devices since conformity to immunity standard EN50082 1 1992 is mandatory The EN50082 1 10992 standard incorporates International Organization for Standardization ISO publications 801 2 and 801 4 which describe Electrostatic Discharge and Electrical Fast Transient requirements ISO 801 5 describes Surge Immunity Requirements and is expected to be adopted as a mandatory requirement under EN50082 1 by the Technical Committee in 1996 Any protector sold into the international community must meet these standards This device has been tested and found to comply with these standards as evidenced by its CE mark Note All test results are for the Model 571 581 al
Download Pdf Manuals
Related Search