Panasonic WV-NF302 Upgrade Guide
Contents
1. 230 User admin logged in will be displayed when successful 5 Enter cd C to move to the C drive of the camera 250 CWD command successful will be displayed when successful 6 Enter bin or binary to set FTP binary mode 200 Type set to I will be displayed when successful Maintenance guide C cam1 gt ftp 192 168 0 10 Connected to 192 168 0 10 220 PrNET FTP server PrNET FTP 1 00 Ready User 192 168 0 10 none admin 331 Password required for admin Password 12345 230 User admin logged in ftp gt cd C 250 CWD command successful ftp gt binary 200 Type set to lI ftp gt put np244setup dat 200 PORT command successful 150 Opening BINARY mode data connection for np244setup dat 226 Transfer complete ftp bytes received in Seconds Kbytes sec ftp gt 7 Enter put xxxxxsetup dat to upload the saved setup data The following message will be displayed when successful 200 PORT command successful 150 Opening BINARY mode data connection for xxxxxsetup dat xxxxx bytes 226 Transfer complete ftp xxxxx bytes sent in x xxSeconds xxx xxKbytes sec 8 The camera will restart automatically 8 Enter bye to finish the FTP session 9 Close the command prompt FEEEEEE ETE PEt Ett t 44444 44 4 4 End Of the COCUMENtHHEEEEEEEEEEEEEEEETEEEEEEEE EEE EET Panasonic System Solutions 3 i Pro_camera_UpgradeGuide A2. 230 User admin logged in ftp gt cd C 250 CWD command successful 3 Enter FTP 192 168 0 10 IP address of the camera ftp gt binary 200 Type set to I 4 Enter the User Name and Password The default User ftp gt get system cfg i an ka 200 PORT command successful Name is admin password is 12345 230 User 150 Opening BINARY mode data connection for system cfg admin logged in will be displayed when successful 226 Transfer complete ftp bytes received in Seconds Kbytes sec ftp gt 5 Enter cd C to move to the C drive of the camera 250 CWD command successful will be displayed when successful 6 Enter bin or binary to set FTP binary mode 200 Type set to I will be displayed when successful 7 Enter get system cfg to download the setup data The following message will be displayed when successful In case of WV NP1000 series Enter get np1000setup dat to download the setup data 200 PORT command successful 150 Opening BINARY mode data connection for system cfg xxxxx bytes 226 Transfer complete ftp xxxxx bytes received in x xxSeconds xxx xxKbytes sec 8 Check if the system cfg or np1000setup dat is saved in the specified directory 9 Enter bye to finish the FTP session and then close the command prompt Panasonic System Solutions 1 __j Pro_camera_UpgradeGuide_A i Pro series camera upgrade guide Maintenance guide 4 Uploading the firmw
3. are The firmware upload is performed through the browser GUI 1 Open the Setup Maintenance menu Network Camera WV NP244 WV NP244 2005 01 01 0 00 2 Open the Upgrade tab menu 3 Click Browse and navigate to the correct firmware e g np244 xxxxx img and select the firmware i E TEA cata Reset to the default settings after completing the 4 Select whether you wish to initialize the setup data a O Do not reset the settings after completing the upgrade during the upgrade process by the radio button It wil take for around 4 minutes with resetting the settings or for around 3 minutes without resetting the settings to complete the upgrade Please wait for a while Please do not operate the browser in the process of the upgrade 5 Click Upgrade Confirmation message will be displayed Click OK to start loading the firmware When Do not reset the settings after completing the Microsoft Internet Explorer upgrade was selected the confirmation message YD When the OK button is clicked data is initialized with upgrade Is it OK will not be displayed 6 Upload in progress is displayed It takes 2 to 4 Upload in progress minutes depending on the camera model When com pleted the browser GUI automatically displays live image 7 After the upgrade check the updated firmware version on the Setup menu Maintenance Upgrade tab Note The following network set
4. i Pro series camera upgrade guide Maintenance guide 1 Outline This manual describes how to upgrade the firmware of the 1 Pro series cameras listed below Applicable models WV NP240 series WV NP1000 series W V NS202 series WV NF284 series WV NW484 series W V NS950 series WV NW960 series WV NF302 series WV NP304 series The procedure includes setup data backup firmware loading and setup data restore 2 Preparation The following items are required for the upgrade 1 PC with specified hardware software Refer to the Operating instructions for detail 2 Network connection between the PC and the camera Default IP address of the camera 192 168 0 10 Note When there is a communication error between the PC and the camera try fixed speed 1OMbps or 100Mbps 3 Firmware of the camera e g np244 xxxxx img which is in the BIG WEB site 3 Setup data backup This procedure is optional as the firmware can be upgraded without initializing the setup data If you wish to backup the setup data follow the procedure below Prior to the FTP transfer open the Setup menu Network setup Network tab and then set the FTP access to allow C cam1 gt ftp 192 168 0 10 Connected to 192 168 0 10 1 Open the command prompt 220 PrNET FTP server PrNET FTP 1 00 Ready User 192 168 0 10 none admin 331 Password required for admin 2 Move to the directory where you wish to save the Password 12345 setup data by using cd command
5. tings will not be initialized during the firmware upgrade procedure On Off for DHCP IP address subnet mask default gateway HTTP port line speed bandwidth control bit rate time amp date Caution ttPEE EEE EEEEEEEE HHHH HHHH HHHH e When upgrading connect the PC in the same subnet as the camera e Do not turn off the power during the upgrade e Do not operate the browser GUI during the upgrade FEEEEEEEEE EEE EEE EERE EEEE EEE EERE EEEEEEEEEEEE EEE EEE EEEEEEEEEEEE EEE E EEE EEEP EEE EE EF 5 Setup data restore This procedure is optional Setup data can be restored as follows This can also be used to copy setup data from another camera same model Prior to loading the setup data change the file name from system cfg to the file name respective to the camera model as shown below except for WV NP1000 series WV NP240 series np244setup dat WV NS202 series ns202setup dat WV NS202A series ns202asetup dat WV NF284 series nf284setup dat WV NW484 series nw484setup dat WV NS950 NW960 series ns950setup dat WV NF302 NP304 series nf302setup dat Panasonic System Solutions 2 _ j Pro_camera_UpgradeGuide A i Pro series camera upgrade guide 1 Open the command prompt 2 Move to the directory where you have saved the setup data by using cd command 3 Enter FTP 192 168 0 10 IP address of the camera 4 Enter the User Name and Password The default User Name is admin password is 12345
Download Pdf Manuals
Related Search