Optoma Technology GT750 User's Manual
Contents
1. Pairing Mode Optoma 3D RF System Optoma 3D RF Glasses and Optoma 3D RF Emitter for Optoma 3D XL Converter Box and 3D ready projector models HD83 HD33 GT750 Contains Patent Pending software and technology from Bit Cauldron Contient les logitiels de brevet en instance et la technologie de la compagnie Bit Cauldron Connections Optoma 3D XL converter box with 3D Emitter Port Connect the Optoma 3D RF emitter to the Optoma 3D XL converter box using the IR Emitter Port as shown below 2 ps P 2 2 2 M p gt 1 VESA 97 Cable Supplied LED Indicators After cable connection the LEDs will display a red moving pattern while the emitter is attempting to acquire a 3D signal and until a 3D sync signal is found The joystick of Optoma 3D RF Emitter can be moved in any direction to enable pairing mode If any Green LEDs are on push the joystick in any direction for a second until all LEDs are off Then push the joystick in any direction for 3 seconds until 3 green LEDs turn ON Release the joystick when 3 green LEDs turn ON You can always remove the cable and start over if you end up in wrong move Prass and Hold the Joystick Down to Cycle Through Available Modes Release the Joystick Button to Select New Mode NA A Restore Factory Defaults Q lt Si Signal Search and Leam Ka iai Pair With Glasses el e h E Manual Performance Tuning adl M Signal Strength Indicator i F i it Mormal Operation Copyr2. de The glasses will stay in pairing mode until they successfully pair with an emitter or until one minute expires While in pairing mode the LED will display the heartbeat pattern If the glasses find an emitter in pairing mode then the glasses will pair with the emitter and resume normal operation as described in Error Reference source not found If an emitter is not found in pairing mode the glasses will not operate but will continue to display the heartbeat pattern until the emitter is placed into pairing mode at which point the glasses will pair and begin normal operating mode immediately If the emitter is not placed in pairing mode the glasses will stay in pairing mode for one minute and then will power down Unpaired mode Follow steps below to put the glasses in the unpaired mode e Start with the glasses turned off e Press and hold down the button e The LED will go on solid after 1 second keep holding down the button e After about 10 more seconds the LED will start pulsing indicating that the glasses are ready to pair keep holding down the button e After about 20 more seconds the LED will start blinking rapidly Release the button now The glasses will restore the factory default settings and firmware This can take several seconds After the process is complete the glasses will resume normal operation If you do not release the button within 20 seconds after the LED begins rapidly blinking the glasses will power
3. ight 2011 Bit Cauldron Corporation Page 1 of 2 After placing the Optoma 3D RF Emitter in pairing mode you will see the red in search of a pair light sequence heartbeat The Optoma 3D RF Emitter will remain in pairing mode for one minute During that time multiple glasses may be paired with the Optoma 3D RF Emitter The only indication that pairing is successful will occur at the glasses When the Optoma 3D RF Emitter cannot pair to any more devices it will display the all available pairs already memorized signal indicated by five red LED s blinking all on and all off for ten seconds The emitter will then return to normal operation The device must be reset to factory defaults to clear the memorized pair list fo fo HI n a ggal Button and LED Indicator Function The top of the left earpiece of the frames contains a button Inside the left earpiece is a red LED Pairing to an emitter With the device off press and hold the power button After 1 2 seconds the red LED will come on Normally you would release the button at this point to power on the glasses Do not release the button after the red LED comes on keep holding down the button After about 10 seconds of the LED on solid the LED will start to pulse with the same heartbeat pattern used by the emitter in pairing mode When you see the heartbeat pattern you must release the button within 10 seconds or the device will go into Restore Factory Defaults mo
4. off Copyright 2011 Bit Cauldron Corporation Page 2 of 2
Download Pdf Manuals
Related Search