Netgear NAS 1100 User's Manual
Contents
1. N E T G E A R Installation Guide NETGEAR ReadyNAS 1100 Start here Follow these instructions to install your NETGEAR ReadyNAS 1100 Then consult the ReadyNAS Setup Manual on your Installation CD for instructions on installing the RAIDar utility and using the FrontView Setup Wizard to configure the ReadyNAS Access the ReadyNAS User Guide on the Installation CD to configure any advanced features The ReadyNAS User Guide is also on the NETGEAR support site at http www netgear com support Warning If you purchased a diskless unit please read the optional disk installation section before installing the RAIDar utility or connecting ReadyNAS to the network First check your package contents Before starting installation check your package contents e ReadyNAS 1100 e Four hard disk trays not included with diskless units e Installation Guide e Warranty Card e Power cable e Ethernet cable e ReadyNAS Installation CD e 16 screws for hard disk installation included only with diskless units Then take a moment to identify the features of your ReadyNAS 1100 A Programmable backup button F Ethernet activity LEDs 2 USB ports 3 G Power LED USB activity light 1 H Disk LEDs 4 Green for disk online I Activity LED Blinks for disk access System reset button Power Button To power off depress for 5 seconds or until LED blinks POF J Mounting ear for 2 post rack mounting DOO OOOOO K2. RAID synchronization ReadyNAS is accessible during this time Normal status ReadyNAS is fully redundant Firmware Version No disks detected if all disk LEDs flash at once and if disk 2 flashes No disks detected repeatedly Bad disk detected if one disk LED flashes once per second Firmware Version The disk corresponding to this LED is bad Root image needs repair if all 4 disk LEDs flash and then disk 1 and Corrupt root disk 2 LEDs flash repetitively K H O X O O O O OCJO OXX OC O O O O O O HK HO HK HK OO He HK HK HK If you purchased a diskless ReadyNAS after you install the hard disks and perform the optional RAID Configuration see the ReadyNAS User Guide for complete instructions you must wait until the volume creation has completed before accessing the Front View Setup Wizard see theReadyNAS Setup Manual It will take up to 2 hours depending on disk capacity An additional 2 to 10 hours are required before the RAID synchronization has completed and the system is fully redundant During the background RAID synchronization access to the NAS will be slower than normal The RAIDar Status column shown in the preceding table will indicate progress Caution While synchronization is underway do not turn off the ReadyNAS 1100 Set up ReadyNAS 1100 Start RAIDar see the ReadyNAS Setup Manual for complete instructions and then power on the ReadyNAS The ReadyNA
3. the following e ReadyNAS connected directly to your network If your client has a static IP address make sure it is on the same IP address subnet as the ReadyNAS device You can do this by configuring your client to obtain its IP address via DHCP Even if your network does not have existing DHCP service the ReadyNAS device will assure that you will get an IP address e ReadyNAS connected directly to your PC If you are connecting a PC directly to ReadyNAS and not through a network first set a static IP address on your PC in the 192 168 168 xxx subnet subnet mask 255 255 255 0 You can then use RAIDar to detect ReadyNAS or you can open a browser and enter the ReadyNAS default IP address https 192 168 168 168 admin to connect to the ReadyNAS Ethernet Cable 4 eee Direct Connect SS ReadyNAS 1100 S ReadyNAS connected directly to your ReadyNAS connected directly to network your PC no cross over cable needed ReadyNAS 00 USB Devices Initialize hard disks if installed separately up to 2 hours up to 10 hours Error Error Error a Installation will abort if an error is detected Legend C LED off Q LED on xt LED slow blinking Ye LED fast blinking 7 Repetitive pattern d A b 201 11142 01 October 2007 Description RAIDar Status Initial boot up Perform RAID configuration on RAIDar optional Click Setup Volume Creation Installing ReadyNAS is not accessible during this time Creating Booting
4. Disk tray door access L Disk tray with lock on latch M Thumb screw latch system module access Q Q OLOO N Cooling fans O Power switch P Power connection 100 240VAC M MOAM W W 50 60 Hz Q Label includes serial number and MAC address R Ethernet ports 2 Install the hard disks optional This is an optional step required only if you purchased a diskless unit 1 Remove disk trays from the unit a Open the door b Press to release the latch c Pull out the tray 2 Set the lock before installing the hard disk into the tray optional ae Ps A Unlocked Default position Dopo ae To open the tray press the round button up xe J a N ame y NR CO Locked the lower position Use a push pin to release the latch and open the tray 3 Install the hard disks into the trays Hard disk x gt SATA connector SATA Hard Disk Drive facing away Disk Tray f J Screws 4 With the latch in the open position slide the disk trays into the unit completely securing the latch and closing the door Finally install the RAIDar utility Your Installation CD contains the RAIDar utility for Windows MAC and Linux See the ReadyNAS Setup Manual for installation instructions When you complete installation of the RAIDar utility you are ready to connect ReadyNAS to your network and then power on ReadyNAS Connect ReadyNAS When connecting ReadyNAS please note
5. S system will appear in the RAIDar scan list Click Setup to start the FrontView Setup Wizard The default user name is admin and the password is netgearl Technical Support Thank you for selecting NETGEAR products At the conclusion of FrontView Setup Wizard configuration complete your product registration or if you choose to register later you can register your product at http www netgear com register Registration on the website or over the phone is required before you can use our telephone support service The phone numbers for worldwide regional customer support centers are on the Warranty and Support Information card that came with your product Go to http www netgear com support for product updates and Web support This symbol was placed in accordance with the European Union Directive 2002 96 on the Waste Electrical and Electronic Equipment the WEEE X Directive If disposed of within the European Union this product should be treated and recycled in accordance with the laws of your jurisdiction implementing the WEEE Directive 2007 by NETGEAR Inc All rights reserved NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR Inc in the United States and or other countries Other brand and product names are trademarks or registered trademarks of their respective holders Information is subject to change without notice
Download Pdf Manuals
Related Search