Monte Carlo Fan Company 5BY52XX User's Manual
Contents
1. Control Attach blade brackets to blades using the blade bracket screws and wash ers provided The blades will have a label showing this side up on each blade 16 Tighen set screws and nuts to secure downrod in yoke 8 Insert downrod into yoke on top of fan body Align the hole in the down rod with hole in the yoke Insert pin through the yoke and downrod until the point appears on the other side Install the keeper Check the fan motor for shipping sta bilizer and remove if present 9 For Canadian installation and for USA fan and light kit combinations over 35 lbs in both flush and downrod mode the safety cable must be installed into the house structure beams using the 3 lag screws provided Make sure that when the safety cable is fully extended the leadwires are longer than the cable and no stress is placed on the leadwires 11 Safety cable installation Safety Cable Lag Screw Lag Screw Safety Cable Washer Lock Washer Push plug from fan and plug from switch plate together 20 Remove the 3 screws from switch cap 21 Install switch plate by placing over the 2 screws and twisting into place Install screw removed and tighten all 3 screws securely 19 Install switch cap into switch plate housing align the 3 holes and install 3 screws and tighten securely 22 1 Check main and branch circuit fuses or circuit breakers 2 Check line wire connections to fan and switch wire conn2. are not equal you can adjust blade levels by the following procedure To adjust a blade tip down insert a washer not supplied between the blade and blade holder at the screw closest to the motor To adjust a blade tip up insert washer not supplied between the blade and blade holder at the two screws farthest from the motor Reverse the position of the washer if blades mount from top of blade 6 If blade wobble is still noticeable interchanging two adjacent side by side blades can redistribute the weight and possibly result in smoother operation 1 Check wire from fan to make sure it is connected to hot wire from house 2 Check for loose or disconnected wires in fan switch housing 3 Check for loose or disconnected wires in light kit 4 Check for faulty light bulbs CAUTION Make sure main power is turned off before entering switch housing 2 If fan sounds noisy 1 If fan does not start 3 If fan wobbles 4 If light does not work Trouble Shooting If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly installation or wiring In some cases these installation errors may be mistaken for defects If you experience any faults please check this Trouble Shooting Chart If a problem cannot be remedied or you are experiencing difficulty in installation please call our Customer Service Center at the number printed on your parts list insert sheet Warning Before servicing or cleaning
3. Quality Ceiling fans Owner s Manual Ceiling Fan Installation Instructions For 5BY52XX Series Fans READ AND SAVE THESE INSTRUCTIONS Total fan weight Place canopy and then yoke cover over downrod as shown Then thread the lead wires and safe ty cable from fan through the downrod as shown Installation work and electrical wiring must be done by qualified person s in accordance with applicable codes and standards ANSI NFPA 70 1999 including fire rated construction Use this unit only in the manner intended by the manufacturer If you have any questions contact the manufacturer After making the wire connections the wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box Before you begin installing the fan Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel Be cautious read all instructions and safety information before installing your new fan Review the accompanying assembly diagrams When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities Make sure the installation site you choose allows the fan blades to rotate without any obstructions Allow a mi
4. ections in switch housing 3 Make sure that any shipping stabilizer has been removed from motor CAUTION Make sure main power is turned off 1 Check to make sure all screws in motor housing are snug not over tightened 2 Check to make sure the screws which attach the fan blade holder to the motor are tight 3 Check to make sure wire nut connectors in switch housing are not rattling against each other or against the interior wall of the switch housing CAUTION Make sure main power is turned off before entering switch housing 4 Some fan motors are sensitive to signals from Solid State variable speed controls DO NOT USE a Solid State variable speed control 5 Allow break in period of 24 hours Most noises associated with a new fan will disappear after this period 1 Make sure that the ridge of the canopy engages the notch in the downrod ball 2 Check that all blades are screwed firmly into blade holders 3 Check that all blade holders are tightened securely to motor 4 Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and junction box is mounted firmly to ceiling joist 5 Most fan wobble problems are caused when blade levels are unequal Check this level by selecting a point on the ceiling above the tip of one of the blades Measure this distance from blade tip to ceilng Keeping measure within 1 8 rotate the fan until the next blade is positioned for measurement Repeat for each blade If all blade levels
5. nimum clearance of 7 feet from the floor to the trailing edge of the blade To reduce the risk of fire electric shock or personal injury mount to outlet box or supporting system acceptable for fan support Mounting must support at least 35 lbs Do not bend blade holders during installation to motor balancing or during cleaning Do not insert foreign object between rotating blades Attach the mounting bracket using only the hardware supplied with the outlet box To reduce the risk of fire or electric shock do not use this fan with any solid state fan speed control device or variable speed control If this unit is to be installed over a tub or shower it must be marked as appropriate for the application NEVER place a switch where it can be reached from a tub or shower The combustion airflow needed for safe operation of fuel burning equipment may be affected by this unit s operation Follow the heating equip ment manufacturer s guideline safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code authorities Before servicing or cleaning unit Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel Note Fo
6. p Ladder Keeper Pin Carefully lift fan assembly onto mounting brack et Rotate fan so that the notch on the ball engages the ridge in the mounting bracket This will allow hands free wiring 10 7 Check the motor for shipping stabilizer and remove if present Attach blade assembly to motor using the motor screws and washers provided Tighten screws securely 17 Remove 1 screw and loosen 2 screws 18 Make wire connections to power source using wire nuts provided Make sure that no filiments are outside of the wirenut After making the wire connections the wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box 12 For pullchain controls follow diagram above Make sure that all exposed wiring is secured inside wire nuts Note Wires from house may vary in color and may not include ground wire After wiring is conplete gently push wires into junction box with wire nuts pointing upward Refer to point 3 of safety tips 13 For control of fan and optional light from wall location follow diagram above NOTE A profes sional electrician is recommended for this type of installation 14 Raise the canopy up and align the two holes in the canopy with the two holes in the hanger bracket Twist into place Secure with two screws provided 15 Light Switch Fan Switch Wall
7. r Outdoor Fans Only Suitable for use in wet locations when installed in a GFCI protected branch circuit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Installation WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING READ AND SAVE THESE INSTRUCTIONS SAFETY TIPS Before you begin installing the fan Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel Before installing this fan make sure the outlet box is properly installed to the house structure To reduce the risk of fire electric shock or per sonal injury mount to outlet box or supporting system acceptable for fan support Mounting must support at least 35 lbs Use metal outlet box suitable for fan support must support 35 lbs Before attaching fan to outlet box ensure the outlet box is securely fastened by at least two points to a structural ceiling member a loose box will cause the fan to wobble Use only the screws provided with the outlet box Remove keeper from pin Pull pin out and replace keeper save for later 3 2 1 4 6 Loosen the 2 set screws and nuts till you can not feel them on inside of yoke 5 TOOLS REQUIRED Phillips Screwdriver Wire Cutters Pliers Ste
8. unit Switch power off at Service panel and lock service dis connecting means to prevent power from being switched on accidentally When the service dis connecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel Customer Service Center 740 S W Loop 820 Suite 110 Fort Worth Texas 76115 1 800 519 4092 Trouble Suggested Remedy
Download Pdf Manuals
Related Search