Makita 6176D User's Manual
Contents
1. 8 Tn kita M Cordless Driver Drill MODEL 6176D INSTRUCTION MANUAL A WARNING For your personal safety READ and UNDERSTAND before using SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE www makitatools com SPECIFICATIONS Capacities No load speed RPM Overall length Net vveight Steel VVood 6176D 10 mm 3 8 4 5 x 20 mm 3 16 x 3 4 O 600 min 210 mm 8 1 4 0 97 kg 2 1 Ibs Battery Charger DC7020B Input A C only 50 Hz 60 Hz Charging time Approx 3 Hr e Manufacturer reserves the right to change specifications without notice e Specifications may differ from country to country GENERAL SAFETY RULES FOR All BATTERY OPERATED TOOLS USA003 1 A WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS Work Area tools create sparks which may ignite the dust or fumes 1 Keep your work area clean and well lit Cluttered benches and dark areas invite acci 3 Keep bystanders children and visitors dents away while operating a power tool Distrac i I tions can cause you to lose control 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power Electrical Safety 4 A battery operated tool with integral bat teries or a separate battery pack must be recharg2. Reversing switch action This tool has a reversing switch to change the direction of rotation Move the reversing switch lever to the FWD posi tion for clockwise rotation or the REV position for counter clockwise rotation When the reversing switch lever is in the neutral position the switch trigger cannot be pulled A CAUTION e Always check the direction of rotation before operation e Use the reversing switch only after the tool comes to a complete stop Changing the direction of rotation before the tool stops may damage the tool e When not operating the tool always set the reversing switch lever to the neutral position ASSEMBLY 002112 1 Tighten 2 Sleeve 3 Ring OPERATION Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged Wait 20 30 sec onds before resuming operation A CAUTION e Always be sure that the tool is switched off before carrying out any work on the tool Installing or removing driver bit or drill bit A CAUTION e Always set the reversing switch lever to the neutral position before installing or removing the bit Hold the ring and turn the sleeve counterclockwise to open the chuck jaws Place the bit in the chuck as far as it will go Hold the ring firmly and turn the sleeve clockwise to tighten the chuck To remove the bit hold the ring and turn the sleeve counter clockwise Screwdriving oper
3. Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase Should any trouble develop during this one year period return the COMPLETE tool freight prepaid to one of Makita s Factory or Authorized Service Centers If inspection shows the trouble is caused by defective workmanship or material Makita will repair or at our option replace without charge This Warranty does not apply where e repairs have been made or attempted by others e repairs are required because of normal wear and tear e the tool has been abused misused or improperly maintained e alterations have been made to the tool IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A SPECIFIC PURPOSE AFTER THE ONE YEAR
4. Make sure cord is located so that it will not be stepped on tripped over or other wise subjected to damage or stress Do not operate charger with damaged cord or plug replace them immediately Do not operate charger if it has received a sharp blow been dropped or otherwise 10 11 12 13 14 15 USC003 1 damaged in any way take it to a qualified serviceman Do not disassemble charger or battery cartridge take it to a qualified serviceman when service or repair is required Incor rect reassembly may result in a risk of electric shock or fire To reduce risk of electric shock unplug charger from outlet before attempting any maintenance or cleaning Turning off con trols will not reduce this risk The battery charger is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the bat tery charger If operating time has become excessively shorter stop operating immediately It may result in a risk of overheating possi ble burns and even an explosion If electrolyte gets into your eyes rinse them out with clear water and seek medi cal attention right away It may result in loss of your eyesight ADDITIONAL SAFETY RULES FOR CHARGER amp TOOL 1 The charger and the tool are specifically designed to work together Do not attempt to charge any other cordless tool with this charger Do
5. TERM OF THIS WARRANTY This Warranty gives you specific legal rights and you may also have other rights which vary form state to state Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you Makita Canada Inc 1950 Forbes Street Whitby Ontario L1N 7B7 883847B067
6. hearing protection must be used for appropriate conditions Tool Use and Care 12 Use clamps or other practical way to secure and support the workpiece to a stable platform Holding the work by hand or 13 14 15 16 17 18 19 20 against your body is unstable and may lead to loss of control Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use tool if switch does not turn it on or off A tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect battery pack from tool or place the switch in the locked or off posi tion before making any adjustments changing accessories or storing the tool Such preventive safety measures reduce the risk of starting the tool accidentally Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a con nection from one terminal to another Shorting the battery terminals together may Cause sparks burns or a fire Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control Check for misalignm
7. not attempt to charge the tool with any other charger 2 Do not charge the tool when temperature is BELOW 10 C 50 F or ABOVE 40 C 104 F Do not attempt to use a step up trans former an engine generator or DC power receptacle Do not store the tool in locations where the temperature may reach or exceed 50 C 122 F Do not incinerate the tool even if it is severely damaged or is completely worn out The tool can explode in a fire Do not charge inside a box or container of any kind The tool must be placed in a well ventilated area during charging SAVE THESE INSTRUCTIONS FUNCTIONAL DESCRIPTION 002059 1 Charging plug 002268 1 Switch trigger 002074 1 Reversing switch lever A CAUTION e Always be sure that the tool is switched off before adjusting or checking function on the tool Charging Connect the charging plug to the charging connector then plug in the charger to the power receptacle Charging takes 3 hours A CAUTION e The battery in your new tool is not fully charged You will need to charge it before use e Do not operate the tool during charging e Overcharging more than 2 days considerably shortens the battery service life Always unplug the charger after completing the charge Switch action To start the tool simply pull the switch trigger Tool speed is increased by increasing pressure on the switch trigger Release the switch trigger to stop
8. 364 Wilmington W Chester Pike Glen Mills PA 19342 610 459 4122 6200 Babcock Blvd Pittsburgh PA 15237 412 366 6363 PUERTO RICO 200 Guayama St Hato Rey PR 00917 787 250 8776 TENNESSEE 4655 Nolensville Rd Nashville TN 37211 615 331 9922 TEXAS 12801 Stemmons Fwy Ste 809 Farmers Branch TX 75234 972 243 1150 12701 Directors Dr Stafford TX 77477 3701 281 565 8665 3453 IH 35 North Ste 101 San Antonio TX 78219 210 228 0676 UTAH 145 E 1300 S Ste 101 Salt Lake City UT 84115 801 359 3410 VIRGINIA 5760 Northampton Blvd Ste 102 Virginia Beach VA 23455 757 460 0280 WASHINGTON 22220 84th Ave So Bldg A Kent WA 98032 253 395 8055 WISCONSIN Lincoln Plaza Shopping Ctr 2245 S 108th St West Allis WI 53227 414 541 4776 CUSTOMER S RECORD When you need service Send complete tool prepaid to one Makita Service Center Be sure to attach a letter to the outside of the carton detailing the problem with your tool Model No 15 VVARNING Some dust created by povver Sanding savving grinding drilling and other construction activities contains chemicals Rnovvn to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e lead from lead based paints e crystalline silica from bricks and cement and other masonry products and e arsenic and chromium from chemically treated lumber
9. ation Place the point of the driver bit in the screw head and apply pressure to the tool Start the tool slowly and then increase the speed gradually Release the trigger just as the screw bottoms out If the trigger is not released the screw may strip out the hole or the screw and or bit may be damaged NOTE e Make sure that the driver bit is inserted straight in the screw head or the screw and or bit may be damaged e When driving wood screws predrill pilot holes to make driving easier and to prevent splitting of the workpiece See the chart 002138 MAINTENANCE Nominal diameter of Recommended size wood screw mm of pilot hole mm 3 1 1 8 2 0 2 2 5 64 3 32 3 5 9 64 2 2 2 5 3 32 3 32 3 8 5 32 2 5 2 8 3 32 7 64 4 5 11 64 2 9 3 2 7 64 1 8 Drilling operation Drilling in wood When drilling in wood the best results are obtained with wood drills equipped with a guide screw The guide screw makes drilling easier by pulling the bit into the workpiece Drilling in metal To prevent the bit from slipping when starting a hole make an indentation with a center punch and hammer at the point to be drilled Place the point of the bit in the indentation and start drilling Use a cutting lubricant when drilling metals The exceptions are iron and brass which should be drilled dry A CAUTION e Pressing excessively on the tool will not speed up
10. draw the built in battery halfway Disconnect the two lead wires from the battery by pulling them from the battery terminals Then withdraw the battery completely To prevent a battery short circuit tape the battery terminals or put the battery into a plastics bag Note Never put two or more batteries into one plastics bag Battery short circuit may result A CAUTION e Never incinerate the battery even if it is severely damaged or is completely worn out It can explode in a fire or toxic materials can leak out of it EN0001 1 Recycling the Battery The only way to dispose of a Makita battery is to recycle it The law prohibits any other method of disposal To recycle the battery 1 Remove the battery from the tool 2 a Take the battery to your nearest Makita Factory Ser vice Center or b Take the battery to your nearest Makita Authorized Service Center or Distributor that has been desig nated as a Makita battery recycling location Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling See your local Yellow Pages under Tools Electric ACCESSORIES A CAUTION e These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more d
11. ed only vvith the specified charger for the battery A charger that may be suit able for one type of battery may create a risk of fire when used with another battery Use battery operated tool only with specif ically designated battery pack Use of any other batteries may create a risk of fire Personal Safety 6 10 11 Stay alert watch what you are doing and use common sense when operating a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose cloth ing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Avoid accidental starting Be sure switch is in the locked or off position before inserting battery pack Carrying tools with your finger on the switch or inserting the bat tery pack into a tool with the switch on invites accidents Remove adjusting keys or wrenches before turning the tool on A wrench or a key that is left attached to a rotating part of the tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper footing and balance enable better control of the tool in unexpected situations Use safety equipment Always wear eye protection Dust mask non skid safety shoes hard hat or
12. ent or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool ser viced before using Many accidents are caused by poorly maintained tools Use only accessories that are recom mended by the manufacturer for your model Accessories that may be suitable for one tool may create a risk of injury when used on another tool SERVICE 21 Tool service must be performed only by SPECIFIC SAFETY RULES qualified repair personnel Service or main tenance per ormed by unqualified personnel may result in a risk of injury 22 When servicing a tool use only identical replacement parts Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury USB022 2 DO NOT let comfort or familiarity vvith product gained from repeated use replace strict adherence to cordless drill safety rules If you use this tool unsafely or incorrectly you can suffer serious personal injury 1 Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the tool live and shock the operator Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical out let Always be
13. etails regarding these accessories ask your local Makita service center e Drill bits e Screw bits e Rubber pad assembly e Wool bonnet e Foam polishing pad e Plastic carrying case Memo 12 eed A etat A EU etrarsa Makita U S A Inc 14930 Northam Street La Mirada CA 90638 5753 SE Fod AA ge er MAIL THIS PORTION Your ansvvers to the follovving questions are appreciated 1 This product was purchased from 3 Hovv did you learn about this product mM Home Center mM Other Magazine Radio Hardware Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other 2 Use of the product is intended for 4 Most favored points are mM Construction Trade Design Repair Service Industrial Maintenance Features Durability Home Maintenance Size Power Hobby Price Other Other Makita Brand 5 Any comments DATE PURCHASED MODEL NO MONTH ae EE MR STATUS INTL LAST NAME COMPANY NAME Married Single ra STREET ADRESS CITY ZIP CODE BE SURE TO COMPLETE THE CUSTOMER S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS Please return this portion by facsimile or mail Facsimile No 714 522 8133 nn FACTORY SERVICE CENTERS 1 800 4 MARITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA 2365 Pelham Parkway Pel
14. ham AL 35124 205 620 1791 ARIZONA 3707 E Broadway Rd Ste 6 Phoenix AZ 85040 602 437 2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd Ste C Little Rock AR 72211 501 224 5733 CALIFORNIA 41850 Christy St Fremont CA 94538 5107 510 657 9881 1421 N Clovis Ave Ste 112 Fresno CA 93727 559 252 5166 14930 Northam St La Mirada CA 90638 5753 714 522 8088 1970 Fulton Avenue Sacramento CA 95825 916 482 5197 1440 South E Street San Bernardino CA 92408 909 885 1289 7674 Clairemont Mesa Blvd San Diego CA 92111 858 278 4471 1714 E McFadden Ave Unit M Santa Ana CA 92705 714 667 5066 1565 Winchester B Campbell CA 95008 0501 408 379 0377 16735 Saticoy St Ste 105 Van Nuys CA 91406 818 782 2440 COLORADO 11839 E 51st Ave Denver CO 80239 2709 303 371 2850 CONNECTICUT 508 Spring St Windsor Locks CT 06096 860 292 6405 FLORIDA 620 Douglas Ave Suite 1302 Altamonte Springs FL 32714 407 774 6000 750 East Sample Road Pompano Beach FL 33064 954 781 6333 Thompson Center Waters 5501 W Waters Ave Ste 406 Tampa FL 33634 813 886 8292 GEORGIA 4680 River Green Parkway Duluth GA 30096 2566 770 476 8911 HAWAII 4510 Salt Lake Blvd Suite A7 Honolulu HI 96818 808 847 0038 ILLINOIS 1450 Feehanville Dr Mt Prospect IL 60056 6011 847 297 3100 INDIANA 8403 Michigan Road Unit 1 India
15. napolis IN 46268 317 334 9980 KANSAS 8819 W 95th St Overland Park KS 66212 913 642 1111 KENTUCKY 1215 S Hurstbourne Parkway Louisville KY 40222 502 326 3740 LOUSIANA 5626 Jefferson Hwy Harahan LA 70123 504 733 4138 MARYLAND 7541 45 Ritchie Highway Glen Burnie MD 21061 410 590 0160 MASSACHUSETTS 232 Providence Hwy Westwood MA 02090 617 461 9754 MICHIGAN 37454 Ann Arbor Trail Livonia MI 48150 313 432 1012 MINNESOTA 6427 Penn Ave South Richfield MN 55423 612 869 5199 MISSOURI 9876 Watson Road St Louis MO 63126 2221 314 909 9889 NEBRASKA 4129 S 84th St Omaha NE 68127 402 597 2925 NEVADA 3375 S Decatur Blvd Suites 22 24 Las Vegas NV 89102 702 368 4277 NEW JERSEY 251 Herrod Blvd Dayton NJ 08810 1539 609 655 1212 NEW MEXICO 5805 Menaul Blvd NE Albuquerque NM 87110 505 881 4619 NEW YORK 4917 Genessee Street Cheektowaga NY 14225 716 685 9503 131 35 31st Ave Flushing NY 11354 718 886 0971 NORTH CAROLINA 3501 G S Tryon St Charlotte NC 28217 704 527 0611 OHIO 6253 E Main St Columbus OH 43213 614 860 0222 6379 Pearl Road Parma Heights OH 44130 440 843 7555 1617 E Kemper Rd Sharonville OH 45246 513 771 0788 OKLAHOMA 552 E Memorial Road Oklahoma City OK 73114 405 752 2655 OREGON 828 19th Avenue N W Portland OR 97209 503 222 1823 PENNSYLVANIA Springwater Plaza
16. sure you have a firm footing Be sure no one is below when using the tool in high locations Hold the tool firmly Keep hands away from rotating parts Do not leave the tool running Operate the tool only when hand held Do not touch the drill bit or the workpiece immediately after operation they may be extremely hot and could burn your skin Some material contains chemicals which may be toxic Take caution to prevent working dust inhalation and skin contact Follow material supplier safety data SAVE THESE INSTRUCTIONS A WARNING MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER amp BATTERY CARTRIDGE SAVE THESE INSTRUCTIONS This man ual contains important safety and operat ing instructions for battery charger Before using battery charger read all instructions and cautionary markings on 1 battery charger 2 battery and 3 product using battery CAUTION To reduce risk of injury charge only MAKITA rechargeable batteries Other types of batteries may burst caus ing personal injury and damage Do not expose charger to rain or snow Use of an attachment not recommended or sold by the battery charger manufac turer may result in a risk of fire electric shock or injury to persons To reduce risk of damage to electric plug and cord pull by plug rather than cord when disconnecting charger
17. the drilling In fact this excessive pressure will only serve to damage the tip of your bit decrease the tool performance and shorten the service life of the tool e There is a tremendous force exerted on the tool bit at the time of hole break through Hold the tool firmly and exert care when the bit begins to break through the workpiece e A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out However the tool may back out abruptly if you do not hold it firmly e Always secure small workpieces in a vise or similar hold down device A CAUTION e Always be sure that the tool is switched off before attempting to perform inspection or maintenance To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers always using Makita replacement parts 9 002144 1 Cover 002145 1 Battery 2 Lead wire 3 Battery terminal eS Ni Cd DISPOSING OF TOOL A Ni Cd battery is built into the handle of the tool Always remove it before disposing of the tool Removing built in battery A CAUTION e Never remove the built in battery from the tool except when disposing of the tool The battery will be damaged or a battery short circuit could result To remove the cover push it in the direction of the arrow while pressing down on the OPEN portion of the cover With
Download Pdf Manuals
Related Search